Can not turn i pad on, i did hard reset and still not working ? help please
can not turn i pad 2 on , I did try the hard reset, no luck. help please
Probably depends on how long you've had it. I don't know what Best Buy's returns/repairs policies are, and whether you're within their exchange period. You could try contacting them
Similar Messages
-
on my iPhone 5 camera photographed not clear. blurry pictures, autofocus does not work. help please!
Could you please describe how you are trying to delete a single text message and it will not work? What are you seeing in place of the trash can icon?
-
HP pavilion dv6 microphone not working . help please . . .
HP pavilion dv6 microphone not working . help please . . .
Hi,
DV6 is a series of hundreads of models, what is yours ? To help us answer question quicker, please read this:
http://h30434.www3.hp.com/t5/First-Time-Here-Learn-How-to/Welcome-Get-started-here/td-p/699035
You may wat to try this first:
1. Right click speaker icon (right hand corner)
2. Select Microphone devices
3. Right click Microphone
4. Enable it
5. Click Apply/Ok
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Can I delete a song from mu PC hard drive and still have it in the icloud?
Can I delete a song from my PC hard drive and still have it in the icloud?
Of course. This will only work if you are using iTunes Match or with the songs you purchased in the iTunes Store, because with iTunes 11, you can listen to them without having them saved on your Mac or PC
-
after update.. i can not start the ipad, when i press agree in the terms ...it will freeze and the screen not working///help please
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
Cheers, Tom -
when i go in my settings on my ipod touch 3gen it says no wi-fi as in i cant connect to any wi-fi at all i tried to restore but did not work HELP PLEASE
See:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar -
Hello
I can not restore my iPhone 4S itunes error says I have 29 and I put it in DFU mode and not working help please
-
My iPad screen is totally frozen with a message box asking me to go to photo stream settings but when either option (ignore or settings) is selected nothing happens. I can't turn off the device either because the screen won't respond. Help please
Try a reset:
Hold the Sleep and Home button down for about 10 second until you see the Apple logo. -
Can i put my photos on my external hard drive and still open them in iPhoto
I am an amateur photographer and an art teacher and i have thousands of photos and music files on my computer that i would much rather put on my external hard drive so they dont take up so much room on my computer. I would like to extend the life of my computer as long as possible and want to keep as much memory free on the actual computer as i can. is there a way for me to put my pictures and or music on my external hard drive and still have it open regularly like it does now in iphoto or itunes?
they are backed up but there are thousands of them i have a small business selling my photos online and i was wondering if i could put them on the external hd and still have them open in iphoto or put my music on the hd and have it open in itunes so i dont have all of it on the computer. i take hundreds of photos a week and my photo gallery is not shrinking by any means any time soon so the more i can put in places other than my hard drive the better but i need them accessible at all times through my iphoto and other programs like photoshop illustrator etc.
DR. -
When trying to open my mail, it opens then closes immediately, I've deleted the account and re-created it 3 times and also done a reset but still not working, help please
Try closing all apps in Multitask Window
1. Double tap the home button to bring up the multi-tasking view
2. Swipe up on the screenshot of the app you want to exit.
3. The app will fly off the screen -
Can not install windows 7 pro using boot camp as mouse and keyboard will not work Help please
I have a new iMac and trying to install Windows 7 Pro using boot camp. I have reached the stage of starting to load windows from the DVD then discovered the mouse and the keyboards not working so I could not interact with windows installation.
Open, if not so already, the Windows formatter. Identify the BC Windows partition. It will be the one listed with the proper size you created and/or will be labeled as a C: drive. Be careful you select the right one or you may be corrupting the entire drive.
Format the partition as NTFS. -
Hi guys, please help me. my son's mini ipad cannot be unlocked because the touchsreen is not responding.. help please. thank you.
A reset should help. Tap and hold the Home button and the On/Off buttons for approximately 10-15 seconds, until the Apple logo reappears. When the logo appears, release both buttons.
No content is affected by this procedure. -
HSRP on 2 3550's not working, HELP please
Hello Everyone,
I am attempting to run and test HSRP but there seems to be some errors.
My first switch is a Catalyst 3550 - 48 Port with SMI image
My second switch is a Catalyst 3550 - 48 Port with EMI image.
I configured HSRP on Vlan12 to try and see if my second switch will take over once I pull the cable out of the first one but it seems like it doesn't.
In the "show standby" command, the second switch shows as "Active router" because I gave it higher priority and it sees the neighbor switch which shows as standby router, so hsrp sees both the switches, knows which one is active and which one is standby but yet when I pull the plug on the first one, network is down, as if it did not revert to the second switch.
My cabling is as follows.
First switch has the first GIG (over fiber) uplink to my provider, the second GIG port is connected to the second gig port on the second switch over fiber as well. The first gig port of the second switch is NOT connected to anything as I only have one provider.
The two ports communicate since hsrp seems the neighbor switches.
The two are configured like this 10.0.0.1 s virtual gateway. 10.0.0.2 is the address of first switch. 10.0.0.3 is address of second switch (backup one). Those IP's are on a MANAGEMENT VLAN which I gave as VLAN ID 100
Now for the VLAN12 I am testing HSRP on, it has VALID INTERNET IP's and not local internal IP's.
Once again, the virtual IP finishes with 225, and I configured 226 as IP on switch1, 227 as IP on switch2.
I am NOT using the track option as I am not sure what it does, I only use the standby priority and preempt options.
So to put it in brief, I am trying to make VLAN12 work with HSRP so that all traffic from VLAN 12 enters switch 1 (from the provider uplink) goes to switch2 since I set vlan12 with higher priority (hsrp) on switch2 goes to the servers, then comes back to switch2, routes to switch1 (since it has to uplink to provider) and out to the internet.
I hope my formatting is not very bad and pretty much understandable.
Can someone please tell me what I am doing wrong and why is hsrp not working for me?
PS: I am suspecting the routing is not done well between one switch and the other so they cannot communicate the traffic, but I am not sure
Please help me
Thank YouHello,
Ok I am copy and pasting the configs of INTERFACE FASTETHERNET 12, VLAN12 and SHOW STANDY on BOTH 3550's...
NOTE: Port 12 is not connected at this point on standby 3550 to the 2950t anymore as I have disconnected the cable since it was not working, this is why there are less details for interface fast ethernet port 12 on standby switch, if you need full details I can give you more details once I connect it again, even with it disconnected, show standby shows the standby 3550 as active for Vlan12, but yet vlan12 operates out of active 3550 even when port 12 was active on standby one.
For privacy reasons, I have XXX'ed the IP's
Here is the data:
--- ACTIVE 3550 -----------------
interface FastEthernet0/12
description Switch 8 Uplink
switchport trunk encapsulation dot1q
switchport trunk native vlan 12
switchport trunk allowed vlan 1,3,12,100
switchport mode trunk
mls qos trust cos
macro description cisco-switch
auto qos voip trust
wrr-queue bandwidth 10 20 70 1
wrr-queue min-reserve 1 5
wrr-queue min-reserve 2 6
wrr-queue min-reserve 3 7
wrr-queue min-reserve 4 8
wrr-queue cos-map 1 0 1
wrr-queue cos-map 2 2 4
wrr-queue cos-map 3 3 6 7
wrr-queue cos-map 4 5
priority-queue out
spanning-tree link-type point-to-point
interface Vlan12
ip address 2XX.XX.XX.226 255.255.255.224
no ip redirects
standby 12 ip 2XX.XX.XX.225
standby 12 priority 95
standby 12 preempt
Vlan12 - Group 12
State is Standby
4 state changes, last state change 1d08h
Virtual IP address is 2XX.Xx.XX.225
Active virtual MAC address is 0000.0c07.ac0c
Local virtual MAC address is 0000.0c07.ac0c (v1 default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.068 secs
Preemption enabled
Active router is 2XX.XX.XX.227, priority 110 (expires in 7.508 sec)
Standby router is local
Priority 95 (configured 95)
IP redundancy name is "hsrp-Vl12-12" (default)
Vlan100 - Group 10
State is Active
2 state changes, last state change 2d03h
Virtual IP address is 10.0.0.1
Active virtual MAC address is 0000.0c07.ac0a
Local virtual MAC address is 0000.0c07.ac0a (v1 default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.064 secs
Preemption enabled
Active router is local
Standby router is 10.0.0.3, priority 100 (expires in 9.608 sec)
Priority 150 (configured 150)
IP redundancy name is "Hsrp-Vlan100" (cfgd)
---- STANDBY 3550 -------------------------
interface FastEthernet0/12
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,3,12,100
switchport mode trunk
interface Vlan12
ip address 2XX.XX.XX.227 255.255.255.224
no ip redirects
standby 12 ip 2XX.XX.XX.225
standby 12 priority 110
standby 12 preempt
Vlan12 - Group 12
Local state is Active, priority 110, may preempt
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.126
Virtual IP address is 2XX.XX.XX.225 configured
Active router is local
Standby router is 2XX.XX.XX.226 expires in 7.756
Virtual mac address is 0000.0c07.ac0c
2 state changes, last state change 1d08h
IP redundancy name is "hsrp-Vl12-12" (default)
Vlan100 - Group 10
Local state is Standby, priority 100, may preempt
Preemption delayed at most a further 0 secs for syncs
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 2.348
Virtual IP address is 10.0.0.1 configured
Active router is 10.0.0.2, priority 150 expires in 7.752
Standby router is local
1 state changes, last state change 2d03h
IP redundancy name is "Hsrp-Vlan100" (cfgd)
Hope this helps you experts to help me :)
Thanks -
Simple copy of reports not working - help please
Hello
I have this function that was written to copy a given report object to a given folder. The code is not working - the copyObj = col.Copy(obj,2) appears to be failing.
Can anyone shed some light on this? Thank you in advance!
- Russell
My function:
function CopyReport (objID, DestFolder, iStore)
dim col
dim obj
dim copyObj
on error resume next
'QUERY FOR OBJECT TO COPY
str = "SELECT * FROM CI_INFOOBJECTS WHERE SI_ID = " + objID
set col = iStore.Query ( str )
obj = col.Item(1)
'COPY THE OBJECT
copyObj = col.Copy(obj,2)
'SET THE PARENTID OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENTID").Value = DestFolder
'SET THE PARENT FOLDER OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENT_FOLDER").Value = DestFolder
'COMMIT THE COLLECTION
iStore.Commit(col)
end functionHi All
I've resolved the problem with the copy and am posting the code below. I'd appreciate it if it could be placed in the appropriate forum so that it may be a resource for other developers in the future. I've left in all of my debugging/error checking code for reference as well.
- Russell
The working copy function (with loads of debugging code) is this:
function CopyReport (objID, DestFolder, iStore)
'Function CopyReport
'Parameters:
' objID - the ID of the report to copy
' DestFolder - the ID of the destination folder for the copy
' iStore - the InfoStore to use
'Returns: A text string that is displayed in a web page via response.write that includes the
' name of the report if copied or the error information as appropriate.
dim col
dim obj
dim copyObj
dim newCol
on error resume next
'QUERY FOR OBJECT TO COPY
str = "SELECT * FROM CI_INFOOBJECTS WHERE SI_ID = " + objID
set col = iStore.Query ( str )
If Err.Number <> 0 Then
CopyReport = "iStore.Query failed<br>"
CopyReport = CopyReport + "<br>Error: " & Err.Number & " - " & Err.Description
CopyReport = CopyReport & "<br>" & str
Exit Function
End If
set newCol = iStore.NewInfoObjectCollection()
If Err.Number <> 0 Then
CopyReport = "newCol creation error"
CopyReport = CopyReport + "<br>Error: " & Err.Number & " - " & Err.Description
CopyReport = CopyReport & "<br>" & str
Exit Function
End If
set obj = col.Item(1)
If Err.Number <> 0 Then
CopyReport = "OBJ = col.item(1) error<br>"
CopyReport = CopyReport & "<br>" & str
CopyReport = CopyReport & "<br>Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'COPY THE OBJECT
set copyObj = newCol.Copy(Obj, 2)
If Err.Number <> 0 Then
CopyReport = "copyOBJ error"
CopyReport = CopyReport & "<br>Count: " & col.Count
CopyReport = CopyReport + "<br>Error: " & Err.Number & " - " & Err.Description
' Exit Function
End If
'SET THE PARENTID OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENTID").Value = DestFolder
If Err.Number <> 0 Then
CopyReport = "Error setting SI_PARENTID to " & DestFolder
CopyReport = CopyReport + "<br>Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'SET THE PARENT FOLDER OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENT_FOLDER").Value = DestFolder
If Err.Number <> 0 Then
CopyReport = "Error setting SI_PARENT_FOLDER to " & DestFolder
CopyReport = CopyReport + "<br>Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'COMMIT THE COLLECTION
iStore.Commit(newCol)
If Err.Number <> 0 Then
CopyReport = "Commit error"
CopyReport = CopyReport + "<br>Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'Return the object info
CopyReport = copyObj.Title
end function
Edited by: Russell L Magidson on Dec 11, 2008 5:12 PM
Edited by: Russell L Magidson on Dec 11, 2008 10:28 PM
Edited by: Russell L Magidson on Dec 11, 2008 10:29 PM -
My iphone 4 automatic lock is not working help please
hi there
my iphone run out of charge very rapidaly and also turn it self off time to time , and when i set auto lock for example 1,2,5 ect minutes it does not work at allDo you have a protective case on the iPhone, maybe it's interfering with the auto-lock?
If that isn't it, try restarting or restoring the iPhone.
Maybe you are looking for
-
How to send an email with an attachment using webdynpros
Hi Friends, i have a table and a toolbar button (send) when i click on that button i have to send an email for the selected row from the table with an attachment. please let me know step by step in detail. Thanks, Mahesh.Gattu
-
Hi All, I have some trouble regarding the QOS implementation for the VOICE communication. I tried to setup the low latency queuing but it showed that it is weighted fair queuing. I want to apply the strict policy ( reserved the bandwidth) of 128 k fo
-
Giving away computer - how do I clean up the hd?
I would like to thoroughly clean / erase everything inside my iMac G5 before giving it away. What is the best way of doing this and can it be done without losing leopard? I have the Leopard disks so should be able to reinstall if necessary. All help
-
Ipad2 not sending e mails they just disappear no comments no problem sending e mails on gmail
IPad 2 will not send emails just disappear no response no problem sending e mails using g mail
-
I have tried to merge two element lists and then process the result with XSLT. The problem is that processXSL() never returns. While playing with my xsl stylesheet it seems that the attributes aren't visible. (There are some older posts who says the