Can only connect one PC to WRT54G2
I recently purchased a WRT54G2 and initially it had been running fine. However, we recently realized that while my PC and my roommate's Mac can connect, we can't get a second PC to connect to our network. We have tried various computers and they all connect and say "limited or no connectivity". However, we have a friend visiting who has a Mac and that connects fine (as do iPhones). Does anyone have any advice on how I can fix this?
Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....
Similar Messages
-
Can only connect one user at a time via VPN?
Hi, long-term Mac user but new to OS X Server. Dug thru the forums quite a bit but couldn't find an answer to this one - hopefully I wasn't searching with the wrong keywords.
Installed OS X Server 10.6 on a MacBook (white, 1 generation back) at the office. Sits behind an Airport Extreme, which is connected to Comcast. Other machines at the office are NOT routed through the Server, but rather connect directly to the Airport Extreme for internet access. I've set up server.mydomainname.com to point to our Comcast address, and I am able to connect via VPN to the server without any problems, and access the server using the server.mydomainname.com address which I pointed to my Comcast IP address, as long as I check "Send all traffic over VPN connection" on my client.
However, when I'm logged in via VPN on one computer, and then log in via VPN on another computer (with the same UID or a different one), the first one loses all connectivity through the VPN - it's as if it had been logged off.
In Server Admin, under the Settings|Network tabs, I have Computer Name set up as "theserver", and Local Hostname as "theserver" (so I can access via theserver.private). VPN is set up to enable L2TP over IPsec, sharing ranges 10.0.1.200 thru 10.0.1.220; no load balancing, no PPTP. Client DNS servers is set to 10.0.1.29.
Any ideas as to why I can only connect with one client at a time?Thanks. I didn't see anything interesting, but then again I'm not up on VPN details. Here's the scenario:
First, I logged in as "user1", and I can use the VPN.
Then, I logged in as "user2", and I can use the VPN with user2, but user1 is no longer able to do anything over the VPN.
Then I hung up with user2, but user1 still can't see anything over the VPN.
Then I hung up and reconnected with user1, and user1 can use the VPN again.
Here's part of the log for this activity. I've replaced potentially identifying info with "XYZ" for safety. Appreciate any thoughts on this!
Tue Oct 19 07:33:08 2010 : L2TP received ICCN
Tue Oct 19 07:33:08 2010 : L2TP connection established.
Tue Oct 19 07:33:08 2010 : using link 1
Tue Oct 19 07:33:08 2010 : Using interface ppp1
Tue Oct 19 07:33:08 2010 : Connect: ppp1 <--> socket[34:18]
Tue Oct 19 07:33:08 2010 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:08 2010 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:08 2010 : lcp_reqci: returning CONFACK.
Tue Oct 19 07:33:08 2010 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:08 2010 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:08 2010 : sent [LCP EchoReq id=0x0 magic=XYZ]
Tue Oct 19 07:33:08 2010 : sent [CHAP Challenge id=0x18 <XYZ>, name = "myserver.private"]
Tue Oct 19 07:33:08 2010 : rcvd [LCP EchoReq id=0x0 magic=XYZ]
Tue Oct 19 07:33:08 2010 : sent [LCP EchoRep id=0x0 magic=XYZ]
Tue Oct 19 07:33:08 2010 : rcvd [LCP EchoRep id=0x0 magic=XYZ]
Tue Oct 19 07:33:08 2010 : rcvd [CHAP Response id=0x18 <XYZ>, name = "user2"]
Tue Oct 19 07:33:08 2010 : sent [CHAP Success id=0x18 "S=XYZ M=Access granted"]
Tue Oct 19 07:33:08 2010 : CHAP peer authentication succeeded for user2
Tue Oct 19 07:33:08 2010 : DSAccessControl plugin: User 'user2' authorized for access
Tue Oct 19 07:33:08 2010 : sent [IPCP ConfReq id=0x1 <addr 10.0.1.29>]
Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfReq id=0x1]
Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
Tue Oct 19 07:33:08 2010 : ipcp: returning Configure-NAK
Tue Oct 19 07:33:08 2010 : sent [IPCP ConfNak id=0x1 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
Tue Oct 19 07:33:08 2010 : rcvd [IPV6CP ConfReq id=0x1 <addr XYZ>]
Tue Oct 19 07:33:08 2010 : Unsupported protocol 0x8057 received
Tue Oct 19 07:33:08 2010 : sent [LCP ProtRej id=0x2 80 47 01 01 00 0f 01 0a 02 1b 63 ff fe a0 dd da]
Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfReq id=0x1 <ms-dns1 0.0.0.1> <ms-dns1 0.0.0.1>]
Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfRej id=0x1 <ms-dns1 0.0.0.1>]
Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfAck id=0x1 <addr 10.0.1.29>]
Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfAck id=0x1]
Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfReq id=0x2 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
Tue Oct 19 07:33:08 2010 : ipcp: returning Configure-ACK
Tue Oct 19 07:33:08 2010 : sent [IPCP ConfAck id=0x2 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
Tue Oct 19 07:33:08 2010 : ipcp: up
Tue Oct 19 07:33:08 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
Tue Oct 19 07:33:08 2010 : found interface en0 for proxy arp
Tue Oct 19 07:33:08 2010 : local IP address 10.0.1.29
Tue Oct 19 07:33:08 2010 : remote IP address 10.0.1.213
Tue Oct 19 07:33:08 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfReq id=0x2 <ms-dns1 0.0.0.1>]
Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfAck id=0x2 <ms-dns1 0.0.0.1>]
Tue Oct 19 07:33:08 2010 : sent [ACSP data <payload len 26, packet seq 0, CI_DOMAINS, flags: START END REQUIRE-ACK>
<domain: name XYZ>]
Tue Oct 19 07:33:08 2010 : rcvd [IP data <src addr 10.0.1.213> <dst addr 255.255.255.255> <BOOTP Request> <type INFORM> <client id 0x08000000010000> <parameters = 0x6 0x2c 0x2b 0x1 0xf9 0xf>]
Tue Oct 19 07:33:08 2010 : sent [IP data <src addr 10.0.1.29> <dst addr 10.0.1.213> <BOOTP Reply> <type ACK> <server id 0x0a00011d> <domain name "XYZ">]
Tue Oct 19 07:33:08 2010 : rcvd [ACSP data <payload len 0, packet seq 0, CI_DOMAINS, flags: ACK>]
Tue Oct 19 07:33:34 2010 : rcvd [LCP TermReq id=0x2 "User request"]
Tue Oct 19 07:33:34 2010 : LCP terminated by peer (User request)
Tue Oct 19 07:33:34 2010 : ipcp: down
Tue Oct 19 07:33:34 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
Tue Oct 19 07:33:34 2010 : sent [LCP TermAck id=0x2]
Tue Oct 19 07:33:34 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
Tue Oct 19 07:33:34 2010 : L2TP received CDN
Tue Oct 19 07:33:34 2010 : Connection terminated.
Tue Oct 19 07:33:34 2010 : Connect time 0.5 minutes.
Tue Oct 19 07:33:34 2010 : Sent 777000 bytes, received 105388 bytes.
Tue Oct 19 07:33:34 2010 : L2TP disconnecting...
Tue Oct 19 07:33:34 2010 : L2TP disconnected
2010-10-19 07:33:34 PDT --> Client with address = 10.0.1.213 has hungup
Tue Oct 19 07:33:50 2010 : rcvd [LCP TermReq id=0x3 "User request"]
Tue Oct 19 07:33:50 2010 : LCP terminated by peer (User request)
Tue Oct 19 07:33:50 2010 : ipcp: down
Tue Oct 19 07:33:50 2010 : sent [LCP TermAck id=0x3]
Tue Oct 19 07:33:50 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp0, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.214).
Tue Oct 19 07:33:50 2010 : L2TP received CDN
Tue Oct 19 07:33:50 2010 : Connection terminated.
Tue Oct 19 07:33:50 2010 : Connect time 3.5 minutes.
Tue Oct 19 07:33:50 2010 : Sent 625383 bytes, received 225586 bytes.
Tue Oct 19 07:33:50 2010 : L2TP disconnecting...
Tue Oct 19 07:33:50 2010 : L2TP disconnected
2010-10-19 07:33:50 PDT --> Client with address = 10.0.1.214 has hungup
2010-10-19 07:33:59 PDT Incoming call... Address given to client = 10.0.1.216
Tue Oct 19 07:33:59 2010 : Directory Services Authentication plugin initialized
Tue Oct 19 07:33:59 2010 : Directory Services Authorization plugin initialized
Tue Oct 19 07:33:59 2010 : L2TP incoming call in progress from 'XYZ'...
Tue Oct 19 07:33:59 2010 : L2TP received SCCRQ
Tue Oct 19 07:33:59 2010 : L2TP sent SCCRP
Tue Oct 19 07:33:59 2010 : L2TP received SCCCN
Tue Oct 19 07:33:59 2010 : L2TP received ICRQ
Tue Oct 19 07:33:59 2010 : L2TP sent ICRP
Tue Oct 19 07:33:59 2010 : L2TP received ICCN
Tue Oct 19 07:33:59 2010 : L2TP connection established.
Tue Oct 19 07:33:59 2010 : using link 0
Tue Oct 19 07:33:59 2010 : Using interface ppp0
Tue Oct 19 07:33:59 2010 : Connect: ppp0 <--> socket[34:18]
Tue Oct 19 07:33:59 2010 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:59 2010 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:59 2010 : lcp_reqci: returning CONFACK.
Tue Oct 19 07:33:59 2010 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:59 2010 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
Tue Oct 19 07:33:59 2010 : sent [LCP EchoReq id=0x0 magic=XYZ]
Tue Oct 19 07:33:59 2010 : sent [CHAP Challenge id=0xf1 <XYZ>, name = "myserver.private"]
Tue Oct 19 07:33:59 2010 : rcvd [LCP EchoReq id=0x0 magic=XYZ]
Tue Oct 19 07:33:59 2010 : sent [LCP EchoRep id=0x0 magic=XYZ]
Tue Oct 19 07:33:59 2010 : rcvd [LCP EchoRep id=0x0 magic=XYZ]
Tue Oct 19 07:33:59 2010 : rcvd [CHAP Response id=0xf1 <XYZ>, name = "user1"]
Tue Oct 19 07:34:00 2010 : sent [CHAP Success id=0xf1 "S=XYZ M=Access granted"]
Tue Oct 19 07:34:00 2010 : CHAP peer authentication succeeded for user1
Tue Oct 19 07:34:00 2010 : DSAccessControl plugin: User 'user1' authorized for access
Tue Oct 19 07:34:00 2010 : sent [IPCP ConfReq id=0x1 <addr 10.0.1.29>]
Tue Oct 19 07:34:00 2010 : sent [ACSCP ConfReq id=0x1]
Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
Tue Oct 19 07:34:00 2010 : ipcp: returning Configure-NAK
Tue Oct 19 07:34:00 2010 : sent [IPCP ConfNak id=0x1 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
Tue Oct 19 07:34:00 2010 : rcvd [IPV6CP ConfReq id=0x1 <addr XYZ>]
Tue Oct 19 07:34:00 2010 : Unsupported protocol 0x8057 received
Tue Oct 19 07:34:00 2010 : sent [LCP ProtRej id=0x2 80 57 01 01 00 0e 01 0a 02 1b 63 ff fe 99 35 cb]
Tue Oct 19 07:34:00 2010 : rcvd [LCP ProtRej id=0x2 82 35 01 01 00 04]
Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfAck id=0x1 <addr 10.0.1.29>]
Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfReq id=0x2 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
Tue Oct 19 07:34:00 2010 : ipcp: returning Configure-ACK
Tue Oct 19 07:34:00 2010 : sent [IPCP ConfAck id=0x2 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
Tue Oct 19 07:34:00 2010 : ipcp: up
Tue Oct 19 07:34:00 2010 : found interface en0 for proxy arp
Tue Oct 19 07:34:00 2010 : local IP address 10.0.1.29
Tue Oct 19 07:34:00 2010 : remote IP address 10.0.1.216
Tue Oct 19 07:34:00 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp0, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.216).
Tue Oct 19 07:34:00 2010 : rcvd [IP data <src addr 10.0.1.216> <dst addr 255.255.255.255> <BOOTP Request> <type INFORM> <client id 0x08000000010000> <parameters = 0x6 0x2c 0x2b 0x1 0xf9 0xf>]
Tue Oct 19 07:34:00 2010 : sent [IP data <src addr 10.0.1.29> <dst addr 10.0.1.216> <BOOTP Reply> <type ACK> <server id 0x0a00011d> <domain name "XYZ">] -
WRT45G: can only connect one pc at the time to internet, cannot login to router setup
Hello,
I don't get this. The complete network worked fine for ... years? After a call with the ISP about a general/different issue, we can now only connect one pc at the time to internet. (We were asked to take out cables and we've put them back).
I've been trying and searching for an answer for hours.
problem:
We can only connect through the router to internet with only one pc at the time (the first pc we connect after starting up the router).
Also we cannot get into the setup menu of the router at 192.168.1.1
We've been trying to reset the modem for 10, 30 seconds.
Auto resolve IP/DNS. DHCP is enabled.
I also remembered that I pushed the SES button, it turned from orange to flashing bluish. I never knew aboutthis function, nor it is mentioned in the manual I downloaded. Now this SES indicator is off.
Also WLAN and DMZ led are off.
I downloaded EasyLink_Connect.exe, went through the setup. It recognises there's internet connection, but stops and says: cisco does not support this modem.
Temp. replacing this WRT45G modem with another one did not resolve the issue.
I have no clue what went wrong, what we did wrong, and how we can resolve this issue? Please help! Thanks
Message Edited by Brammm on 11-27-2008 03:13 PMOkay!
1. (results when having assigned a static IP) :
Windows IP-configuratie
Primair DNS-achtervoegsel. . . . .:
Knooppunttype: . . . . . . . . . .: onbekend (unknown)
IP-routering ingeschakeld. . . . .: nee (no)
WINS-proxy ingeschakeld . . . . . : nee (no)
Ethernet-adapter LAN-verbinding:
Verbindingsspec. DNS-achtervoegsel:
Beschrijving . . . . . . . . . . .:
VIA Compatable Fast Ethernet Adapter
Fysiek adres. . . . . . . . . . . : 00-16-17-CE-D5-40
DHCP ingeschakeld:. . . . . . . . : nee (no)
IP-adres. . . . . . . . . . . . . : 192.168.1.20
Subnetmasker. . . . . . . . . . . : 255.255.255.0
Standaardgateway. . . . . . . . . : 192.168.1.1
DNS-servers . . . . . . . . . . . : 192.168.1.1
(results without having assigned a static IP: automatic config.) :
Ethernet-adapter LAN-verbinding:
Verbindingsspec. DNS-achtervoegsel:
Beschrijving . . . . . . . . . . .:
VIA Compatable Fast Ethernet Adapter
Fysiek adres. . . . . . . . . . . : 00-16-17-CE-D5-40
DHCP ingeshakeld. . . . . . . . . : ja (yes)
Autom. configuratie ingeschakeld. : ja (yes)
IP-adres. . . . . . . . . . . . . : 84.30.99.32
Subnetmasker. . . . . . . . . . . : 255.255.254.0
Standaardgateway. . . . . . . . . : 84.30.98.1
DHCP-server . . . . . . . . . . . : 213.51.144.90
DNS-servers . . . . . . . . . . . : 212.54.40.25
212.54.35.25
2. I do have another router, when I try that one, the problem we have remains. So that's a bit strange to me. That one is supposed to be working.
Does this SES function configure anything other than the modem? So, does it alter PC configurations? I have no clue. We even start to wonder whether the ISP is able to set up their internet in a way that unables us to make use of a router? That would be ridiculous
Message Edited by Brammm on 11-30-2008 04:03 AM -
Can only connect one laptop via AEBS wifi
i was able to use my internet service with my Apple Airport Express Base Station (AEBS) for months without any problem and it was capable of simultaneous internet sharing (via wifi) among 3 laptops without the need to enter / directed to the internet provider's portal per connection (to enter account number and service reference number for authorization - works like a username and password for the connection)
not until their so-called "network upgrade" as stated by my internet provider's tech support - I am now only able to connect a single laptop via the AEBS
attempting to connect the other 2 laptops simultaneously with the 1 laptop on wifi connection was unsuccessful
can not connect more than one laptop to my internet service through the AEBS simultaneously
and whenever one laptop tries to connect to my internet service provider (via AEBS), you are immediately directed to the internet service provider's portal to enter your Account Number and Service Ref Number - you have to go through this every time you want to connect
i have already reset the settings of the AEBS and still, the problem persisted
any ideas on how to resolve this issue? is the problem with my internet service provider or my AEBS?
thanks in advanceSounds like they've done something to stop more than one computer sharing the internet connection. It's possible that they've done this to prevent unauthorised access (by neighbours, etc.), but it's also possible that they've done it to stop people sharing one account - an attempt to get more customers to pay extra?
I'd be tempted to look for a new ISP if they can't help. -
At home I have a HP PC, netbook and Sony laptop with no connection issues. Last year I bought an iPad 1 for my wife. This year I bought an iPad 2 for myself. However, only one iPad can connect to the wifi home network at a time. If I am using the iPad2 then the iPad1 fails to connect to the internet. if the iPad1 is being used then the iPad2 cannot connect. I tried resetting iPad network settings for both, reset router, and updated both iPads to latest software/firmware yesterday. Right now the only iPad that shows any connection is the iPad1. The iPad2 does not see the home network or any other outside network. Any suggestions or ideas on how to resolve this? It is odd the network issues only affect the iPad's.
@dananova,
It sounds like you need to either increase the number of dynamic IP addresses your router will hand out or change some of your devices to static IP addresses.
Check the router manual on how to change the dynamic IP range of your router. If you don't have a manual, you can go to Belkin's website and download it.
To change the IP address of your iPads to static addresses, go to Settings > Wi-Fi and tap the ">" next to the name of your wireless network. DHCP should be highlighted. Write down the all the settings on the screen. Next tap the Static button. Enter the exact same information that you copied from the DHCP screen with the exception of the last 3 digits of the IP address. Enter a new 3 digit number in this spot. Generally the original IP address will end with a low number such as 009, so pick a number that is not that low but less than 255. I would suggest a range of 240 to 250, unless the original IP range falls near this range. Also make sure you use a different 3 digits for each device you set to use a static IP address. -
Clients behind shared wireless can only connect one at a time to RV042
I am using a RV042 HW version 3 (black front panel and blue user interface).
I have have 2 vpn users who share an apartment.
They use a wireless router to get to the internet.
Both use Windows 7 (firewall enabled) and the latest QuickVPN client.
As it is, only one of the users can connect at the same time.
When one is already connected the other gets a message "the remote gateway is not responding"
Has anyone else experienced something like this ?
Thanks in advance.
These are the logs from the PC that connected ok:
From wget_stop_error.txt
--10:29:50-- https://Serena:*password*@180.243.235.82/StopConnection.htm?version=1?status=disable?IP=192.168.0.101?PASSWD=*password*?USER=Serena
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//stopconn.conf'
Connecting to 180.243.235.82:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: unspecified [text/html]
0K 96.68 KB/s
10:29:50 (96.68 KB/s) - `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//stopconn.conf' saved [99]
From wget_request_error.txt
--10:29:45-- https://Serena:*password*@www.vantagebanking.com:60443/CheckIsakmp.htm?version=1?IP=192.168.0.101?PASSWD=*password*?USER=Serena*password*@www.vantagebanking.com:60443/CheckIsakmp.htm?version=1?IP=192.168.0.101?PASSWD=*password*?USER=Serena
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//isakmp_status.conf'
Resolving www.vantagebanking.com... 180.243.235.82
Connecting to www.vantagebanking.com[180.243.235.82]:60443... connected.
HTTP request sent, awaiting response...
End of file while parsing headers.
Giving up.
From wget_error.txt
--10:29:13-- https://Serena:*password*@180.243.235.82/StartConnection.htm?version=1?IP=192.168.0.101?PASSWD=*password*?USER=Serena
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf'
Connecting to 180.243.235.82:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: unspecified [text/html]
0K 176.76 KB/s
10:29:14 (176.76 KB/s) - `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf' saved [181]
From Log.txt
2011/07/16 10:29:12 [STATUS]OS Version: Windows 7
2011/07/16 10:29:12 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/07/16 10:29:12 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:12 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:12 [STATUS]One network interface detected with IP address 192.168.0.101
2011/07/16 10:29:12 [STATUS]Connecting...
2011/07/16 10:29:12 [DEBUG]Input VPN Server Address = www.vantagebanking.com
2011/07/16 10:29:13 [STATUS]Connecting to remote gateway with IP address: 180.243.235.82
2011/07/16 10:29:14 [STATUS]Remote gateway was reached by https ...
2011/07/16 10:29:14 [STATUS]Provisioning...
2011/07/16 10:29:24 [STATUS]Success to connect.
2011/07/16 10:29:24 [STATUS]Tunnel is configured. Ping test is about to start.
2011/07/16 10:29:24 [STATUS]Verifying Network...
2011/07/16 10:29:30 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:33 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:36 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:39 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:42 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:45 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2011/07/16 10:29:49 [STATUS]Disconnecting...
2011/07/16 10:29:53 [WARNING]Failed to disconnect.
And these are the ones from PC # 2 which failed to connect with error "The remote gateway is not responding"
This error just keeps looping around
From wget_error.txt
--10:29:21-- https://Paul:*password*@180.243.235.82/StartConnection.htm?version=1?IP=192.168.0.100?PASSWD=*password*?USER=Paul
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf'
Connecting to 180.243.235.82:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: unspecified [text/html]
0K 174.80 KB/s
10:29:22 (174.80 KB/s) - `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf' saved [179]
From Log.txt
2011/07/16 10:29:18 [STATUS]OS Version: Windows 7
2011/07/16 10:29:18 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/07/16 10:29:18 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:18 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:18 [STATUS]One network interface detected with IP address 192.168.0.100
2011/07/16 10:29:18 [STATUS]Connecting...
2011/07/16 10:29:18 [DEBUG]Input VPN Server Address = www.vantagebanking.com
2011/07/16 10:29:20 [STATUS]Connecting to remote gateway with IP address: 180.243.235.82
2011/07/16 10:29:22 [STATUS]Remote gateway was reached by https ...
2011/07/16 10:29:22 [STATUS]Provisioning...
2011/07/16 10:29:32 [STATUS]Success to connect.
2011/07/16 10:29:32 [STATUS]Tunnel is configured. Ping test is about to start.
2011/07/16 10:29:32 [STATUS]Verifying Network...
2011/07/16 10:29:38 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:30:51 [WARNING]Failed to ping remote VPN Router!I just removed the tunnel and after that I cannot log in any more.
I rebooted the router after removing the tunnel.
I have tried many times.
I use remote management from Singapore with the RV042 in Jakarta.
Other users also cannot log in.
"Verifying network" is as far as we get.
This is the log:
2011/07/19 14:54:06 [STATUS]OS Version: Windows XP
2011/07/19 14:54:06 [STATUS]Windows Firewall is OFF
2011/07/19 14:54:07 [STATUS]One network interface detected with IP address 10.71.11.9
2011/07/19 14:54:07 [STATUS]Connecting...
2011/07/19 14:54:07 [DEBUG]Input VPN Server Address = 180.243.235.82
2011/07/19 14:54:07 [STATUS]Connecting to remote gateway with IP address: 180.243.235.82
2011/07/19 14:54:09 [STATUS]Remote gateway was reached by https ...
2011/07/19 14:54:09 [STATUS]Provisioning...
2011/07/19 14:54:19 [STATUS]Success to connect.
2011/07/19 14:54:19 [STATUS]Tunnel is configured. Ping test is about to start.
2011/07/19 14:54:19 [STATUS]Verifying Network...
2011/07/19 14:54:23 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:24 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:25 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:26 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:27 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:28 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2011/07/19 14:54:37 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:38 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:39 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:40 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:42 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:42 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
I have restored from the export .config file and all is back to normal.
So I better leave the single tunnel as it is.
I will try with spare RV042 when I am back in Jakarta -
Can only connect to Internet from one computer at a time on network
I have a 2 computer network in my office networked with an Asante 10/100 hub. The computers are a iMac 24 (Intel) and an old G4 (PCI). The network has worked fine until just recently. Now, I can only connect to the Internet with one computer at a time...(DSL connection). I checked cables, ports, etc, and I'm wondering if this is a 10.4.9 issue. Coincidentally, I noticed that I am not able to access the Internet via Win XP using Parallels which also worked fine up until recently. I checked with the ISP (AT&T) who confirmed that all is OK on their end. Anyone have similar problem? Could OS X 10.4.9 be the culprit? Any help on this will be much appreciated. Thanks.
iMac 24 Mac OS X (10.4.9) 2G RAM; NVIDIA GeForce 7600 GT 256I'd consider that a 3 computer network, Parallels being a virtual machine would alias the ethernet interface and need its own IP address. That may or may not have anything to do with your problem. Actually, the way you've described things, it sounds like a lot has to do with your contract with ATT. Is there a routing device at your end?
The only way 10.4.9 could be the culprit would be if it were the routing device.
-Phil -
Can only connect from one direction
I'm having trouble video confrencing... I tried searching the forums, but I'm having trouble thinking of clever search terms.
I can only connect from one direction with one person. They can invite me to a chat and it works fine every time. However when I invite them it always fails. I can invite other people and it works fine though.
This doesn't seem like a typical router problem, because they can invite me and we videochat just fine.
This has been a problem for most versions of iChat that I can remember, but I'm using 3.1.5 currently.Hi
Is the other person a PC user.
Tony -
Can only print one item at a time
Hey everyone,
Bit of a Photoshop novice here, use it for DVD covers and labels. I have been using CS3 previously but upgraded to CS5.5 last year. The thing is on CS5.5 I can only print one page at a time even when I input say 20 copies to be printed, only one will print. That goes for the regular printer for printing covers and the disc printer.
I can open CS3 up and right away it will print however many I ask it to.
Is there something I am missing? Something so painfully obvious that it is staring me in the face but I am just not seeing it?
Thanks in advance!It isn't a printer setting. I have 3 different printers connected to my system and all of them worked with CS3 fine. And when I delete the preferences folder for CS5.1 it works as it should but only once, then afterwards it only prints one copy, no matter how many I ask it to print!
So if it works when the preferences have been removed, then fails to work afterwards, how can that be a printer setting?
I have read elsewhere that others have had similar issues with CS5 and Windows 7. -
Database 'TEST' is already open and can only have one user at a time.
Hi all,
Could some help on this issue as per urgency!
Database 'TEST' is already open and can only have one user at a time.
I also tried this command but having the same error, please let me know how to troubleshoot this issue
Use Master
GO
Select * from master.sys.sysprocesses
Where spid > 50
And dbid=DB_ID (‘StuckDB’)) -- replace with your database name
ThanksHi Tony,
sorry got the same error again, it can't allow me sp_who2 as well
I tried above command got the following error
Changes
to the state or options of database ‘TEST’ cannot be made at this time. The database is in single-user mode, and a user is currently connected to it.Msg 5069, Level 16, State 1, -
got a new laptop. unsure of firefox verson on old as the computer quit taking a charge.
but essentially on my old laptop if a window had six downloadable links i would be able to download all six at once. now i can only download one link at a time. this is very annoying. i do not believe it is an issue with the new laptop itself as it is a highend toshiba.Hello cherokeeguy, go to [http://kb.mozillazine.org/About:config about:config] find [http://kb.mozillazine.org/Network.http.max-persistent-connections-per-server network.http.max-persistent-connections-per-server] right-click on it, select modify and put a greater value, try 10 or 16, click ok to save it, exit firefox and restart it.
BUT this normally should not happen !
check it also in [https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Safe Mode], select '''''"Start in Safe Mode" '''''and see if this happen again, if not see: [https://support.mozilla.org/en-US/kb/troubleshoot-extensions-themes-to-fix-problems Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]
also try to update to the latest firefox 16.0.1
thank you
Please mark "Solved" the answer that really solve the problem, to help others with a similar problem. -
TS1398 i have trouble connecting to wifi i can only connect from less than a feet from my router
i have a iphone4 and i am haveing trouble conneting to wifi can only connect to wireless router from one feet away
Hi there,
You may want to take a look at the troubleshootings steps found in the article below.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
-Griff W. -
I can only access one web site . www.cisco.com. I am connected to the internet via a lynksys DSL Router, I am using dhcp and NAT from the Lynksys note:works fine for 3 other windows based pc's.
when I try to connect to any other site the page Hangs during load and neve displays.
I can ping all of the web sites that do not come up
I am using a SunBlade 100 and did a new install. I tried the install with webstart and had the same result during the install. again I can only open sucessfully www.cisco.com.Hello!
I am getting this error, but the above fix does not solve the issue, however I do know what has caused it.
I have an edmx file in a WCF webservice which feeds a silverlight app. The edmx is quite complex and a bit fragile, but was working fine up until I introduced our Industry Codes view into the model. The view is basically { ID, ParentID, Name, ... }. In my model I have created an association to itself which describes Children(*)/Parent(0/1) so I have a nice and tidy hierarchical structure. The edmx and the service build without any errors - hurrah! However, when I update the service reference I then get the below error (and a whole load of others as none of the webservice objects exist anymore):
Error 21 Custom tool error: Failed to generate code for the service reference 'WCF_ContactAdmin'. Please check other error and warning messages for details. X:\2008-054 ContactAdmin_Silverlight\Contact2_Admin_Silverlight\Service References\WCF_ContactAdmin\Reference.svcmap 1 1 Contact2_Admin_Silverlight
When I try the fix mentioned in the link above this error disappears, but then so do all the objects in the datamodel, so I cannot continue from there.
Having the hierarchical data objects defined in the EDM will make like so much easier in future, any help will be greatly appreciated, thank you!!
Tim
Web Developer at Terrapinn -
Because of a problem, I uninstalled Firefox once, reinstalled it and it ran. I had a problem so I uninstalled/reinstalled it again. Now it will not run. I get an error message saying that firefox is running and you can only run one at a time. I have uninstalled multiple times and can't figure out what is running. The is only one Firefox installed and it is not open. What does this mean and how do I fix it?
If you use ZoneAlarm Extreme Security then try to disable Virtualization.
*http://kb.mozillazine.org/Browser_will_not_start_up#XULRunner_error_after_an_update
See also:
*[[/questions/880050]] -
I am trying to print all the PDF pages in a range of 5 pages but can only print one page at a time . . . It will print the current page only, but not all or pages 1-5. I need to go to the next subsequent page and command to print current page; continuing with this procedure until all pages are printed one at a time. Can this be overcome?
You can use printPages(1, 5), however I need to know how you print current page.
Maybe you are looking for
-
I am able to open a PDF file but I cannot save it. The file was stored elsewhere on line. Does anyone know how to save it to my ipad?
-
DEPRECIATION PROCESS IN ORACLE ASSETS(FADEPR)
제품 : FIN_FA 작성날짜 : 2003-05-20 DEPRECIATION PROCESS IN ORACLE ASSETS(FADEPR) ============================================= PURPOSE Oracle Assets 에서의 depreciation process 를 간략하게 기술 Explanation DEPRECIATION IN ORACLE ASSETS ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
Hi How do I allocate Contiguous memory space to JVM 1.3 in Windows and AIX? Regards Sudhindra
-
After installing Firefox 4 my bank website login is slow, why?
MacBook, Mac OS X 10.6.7, Firefox 4 4.0.1 My bank login has strong security which worked fine under Firefox 3. After I loaded Firefox 4 the time needed to go through bank security, i.e., after entering password and before painting the initial page, h
-
Trying to view an SD version of an iTunes movie on my MacBook Pro and it repeatedly freezes 9 minutes into movie. Using iTunes 10. Any suggestions to correct this problem?