Can Prime Infrastructure 2.0 enable port 8080 for Browser access?

By the offical document, port 8080 is pre-defintied for the Browser access but it is disabled by default.
I am finding a way to enable the port, but I cannot find any guide on cisco site.
Did anyone know how to enable the 8080 port?
Thanks in advance.
Louis

HIi Hoi;
As per cisco document : http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1082023
Configuring Server Settings
The Server Settings page allows you to enable or disable the TFTP, FTP, HTTP, HTTPS, or Compliance Service. To turn the server settings on or off:
Step 1 Choose Administration > System Settings.
Step 2 From the left sidebar menu, choose Server Setting.
Step 3 If you want to modify the FTP and TFTP directories or the HTTP and HTTPS ports that were established during installation, enter the port number (or port number and root where required) that you want to modify and click Enable or Disable.
The changes are reflected after a restart.
I am not sure but try to change the port number 8080 in HTTP Forward option and save it, then restart it.
I think it will work.
Regards
Don't forget to rate helpful posts

Similar Messages

Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

Prime Infrastructure/ Assurance is positioned today more towards managing network elements and network performance, rather than server infrastructure. We are in the process of adding Datacenter component support, with more focus on Nexus and UCS- due later this year.
Having said that, Prime Infrastructure allows the system user to add custom SNMP polling templates, which can then be used for polling any SNMP based values from any SNMP enabled device. These can be used to collect the information you specified below and the polled information will be available in dashboards and reports.

How to enable digital signature for browser enabled infopath form?

Dear all,
I have designed infopath form and published it into the document library. I want to provide signature option on the browser enabled infopath form.
I have created it using secion and digital signature control.
but I am getting this message.
When i click on Yes . I get following screen.
And it just hang here. I have enabled the active x control feature for IE.
Please tell me where i should install this component and how it can be done?
I have access only to the sharepoint site.
Thanks

Hi,
According to your post, my understanding is that you want to enable digital signature for browser enabled infopath form.
To be able to sign this form, you need to activate two Windows Internet Explorer add-ons. Click the Information Bar in the dialog box, and then click Run ActiveX control to activate each add-on.
Then you need to active the following add-on.
In my environment, after I click the Next button, it open the picture as below.
Once I click the link to add the add-on as above, everthing works well.
For more information, you can refer to:
Add a digital signature to a browser-enabled form
Digital Signatures in InfoPath 2010
Best Regards,
Linda Li
Linda Li
TechNet Community Support

With iOS 7.0.2 I lost many apps from my screen. They are in the Apps store under "updates." I can open them but can't get them back onto the desktop for easy access.

How can I get my Apps back on my iPhone screen? Many disappeared when I updated to i0S 7.0.2. I can open them from the Apps store where they are listed in Updates. But I can't get them back on my desktop for easy access.

Try restoring the iPhone from backup.

Prime Infrastructure 2.1 - SFP port alarms to email/show total network traffic speed

Hello,
Running Prime Infrastructure 2.1 with assurance license.
I have two questions:
1. Setting up alarms in PI 2.1. I've set up a port group of my main switches that have TenGig links to our main router. I have set up a monitor template that has only interface availability on it and then deployed it. In theory, this should email me, the contact (where I put my email address in), when the ports that I have set up go down, correct?
2. I want to monitor the entire traffic of the network going in to the router from our TenGig ports. I've messed around with the dashlets and adding my port group to the WAN utilization dashlet but only see % of utilization. I'd like to be able to see raw traffic stats from those ports. I'm sure I'm missing something. Where do I need to look in PI to check raw traffic data in Mbps/Gbps from my ports.

In my first question, I do not get an email when a port goes down. I set up a test port and when I pulled it, after about 10 minutes, it had never sent me an email. I will continue to look through what I've been doing to see if I can figure it out.

Can't Connect to SMP on port 8080

Hello,
I have 2 SMP 3.0 SP06 servers, one installed in remote server "azure server"and the other o is installed internally in local server that doesn't have an internet connection.
I can connect to the remote server , I can so the following :
- open admin page
-open integration gateway management page
- telnet port 8080 and port 8083
-register client on application and execute OData services from Advanced REST Client
but when I'm trying to do the same on SMP installed on the local server , I am only able to
- open admin page
- open integration gateway management page
- telnet port 8083 only
but I can't :
- telnet port 8083
- register client on application and execute OData services from Advanced REST Client, as this is done through port 8080.
I executed the command " netstat -a | find "8080" "
and it has the same result on both servers :
screenshot from local server, the other server on azure has the same result.
I have stopped and started SMP services, and still can't connect to port 8080.
I added a role in firewall for port 8080 to allow connection but still same issue, I even disabled the firewall with no hope.
this is screenshot from Advanced REST client, it gives no response after timeout:
screenshot from telnet command:
Am I missing something ?
Thanks,
Hossam

What do you see when you run?
http://localsmpserverip:8080
https://localsmpserverip:8081
when I tried to access the two links :
http://localsmpserverip:8080
https://localsmpserverip:8081
it gives me after timeout this :
but when I tried to access:
https://localsmpserverip:8083
it downloaded a file.
and as I mentioned I can access the cockpit and telnet port 8083.
do you see the same PID for all SMP ports?
" netstat -a | find "8080"
" netstat -a | find "8081"
" netstat -a | find "8082"
" netstat -a | find "8083"
8080 might being used by some other service.
they all used by java.exe and not used by any other process
You can achieve above with HTTPS (secure connection) and 8081 as well.
I tried to register using port 8081 same response :

A job in Cisco Prime Infrastructure 2.1 has been running for 50 days

I found a job (SAM_Poller_22_15_GETVPNPoller_1878262177) in cisco prime infrastructure 2.1 (Administration -> Job Dashboard -> System-defined), which has been running for about 50 days. Is this normal? How can I stop it? Thanks for any help..
SAM_Poller_22_15_GETVPNPoller_1878262177
PollerJob
In-Progress
Running
2014-09-19 01:28
49 Days 01 : 28 : 37

Not normal, seems to be stuck. Try to stop (ncs stop) and start (ncs start) the system processes, which should stop this job.
If it happens again, i would recommend to open a TAC case for further investigation.
-Thanks
Vinod

TCP's port mapping for safe access

So, I have a statical IP and need to organize safe access to my domestic NAS via Capsule from Global Internet, it means I need https://.
As I know (may be it's not) TCP's set 443 can provide https:// only.
I could not find such TCPs pre-set in Capsule.
I tried to use all pre-set (one after the other) and even made a new set with TCP 443 (just by hand), but all my attempts ended by changing TCP's 443 to 8080 automatically and I saw https:// when I tried to make a safe enter.
Pls., explain, how can I do it?
Thanks' a lot advance.

You have to map port 443 to the NAS IP in your local lan..
You should be able to access it no problem.. there is nothing preset on the TC.
Read the instructions by Tesserax on port mapping for v5 or v6 utility depending on which one you use.
https://discussions.apple.com/community/wireless/airport?view=documents
IMHO if your TC is not the latest AC you will have far more success with v5 utility.
v6 seems to have issues making it stick.
You can load the older version into Mountain Lion .. but according to your profile you are on 10.6 so still fine for v5.

How can i Store web links in my iPad for easy access?

How can i store web links in iPad for easy access?

Add them as a bookmark in the Safari web browser. You can sync bookmarks between your computer and iPad too using iTunes or iCloud.

Can't set IE Desktop as default program for Assigned Access

I have searched everywhere for this answer. Kiosk mode/assigned access is excellent. But it appears that you can only use IE Modern (Metro) for assigned access and the problem with that is I have found no way to completely lock down IE Modern.
I can only partially lock it down but users can still get to the address bar and settings very easily.
I either need some advice on setting IE to complete lockdown or how to set IE desktop for Assigned Access.

Perhaps you can create a special application that will be selected for Assigned Access. This application will then start the desktop variant of Internet Explorer (or an intermediate desktop program). There are some articles about such
operation based on Launcher class and custom file association.

Prime infrastructure 2.1 - no E-Mail for syslog alarms

Hi,
I´ve now configured my CPI (2.1) for receiving all syslog and SNMP Traps sent from my switches (catalyst 2960s). Everything works fine so far.
Now i want CPI to send an email for the syslog event "security violation". I can see this event in Syslog view and also in events with severity cirtical like i defined in severity configuration - but no email is generated?? Do i have to configure something special if i want to have an email notification for syslog generated alarms?
The reason for this problem (maybe there´s another solution): We use 802.1x authentication and i want to know when there´s a security violation and a port is set to error disabled state. I´ve configured my switches to send SNMP Traps for "errdisabled" but they never appear in CPI.
Because of that i´ve configured syslogs and saw that "security violation" is logged by syslog but no email is created :((
Thank you very much for you help!!

We're experiencing similar problem when syslog for STP loop (severity 2) is received, recognized as critical but no alarm is created.

Can Ideapad Lynx k3011 micro USB port use for data communication?

Greetings,
I would like to connect on one end an VAG-Com USB dongle (http://www.ross-tech.com/vag-com/hex-usb+can.html) via a Micro USB adaptor to the tablet and the CAN bus to my car on the other end to turn some car features on and off. Can the Micro USB port on the tablet be used as communication device to achieve this?
Thanks,

Just check ebay or http://www.parts4repair.com/brands/Sony.html
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Can DVDSP create a CSS enabled Video_TS ready for replication?

Can I create a copy-protected DVD with a Video_TS folder ready for replication?
From what I understand, copy-protected DVD's for replication can only be created through the DDP file process. That means that the replicator must apply a "mastering process" to the files before a glass master is created.
I am being told my a replicator that in the past, they have received discs from clients that are copy protected and ready for replication. Is this possible? Can I burn these type of discs with DVD Studio Pro and a built in burner?
Ed

Here is a post from another site that provides more details--basically the answer to my question is no.
Can I create a copy-protected DVD with a Video_TS folder ready for replication?
Nope. All CSS encrypted DVD's must be in DDP or CMF format on either hard drive, DLT, or DVD-R (provided as DVD-ROM, not Video_TS).
The "mastering process" is us (replicators) adding the actual CSS keys to the final image while it is premastering. DVD Studio Pro "flags" the master with CSS. The keys are added in the premastering stage at the replicator before glass is made (unless you use Scenarist, you can add the keys upon output, which doesn't make it playable but the Eclipse software will see the keys are present and we don't have to add them).
I am being told by my replicator that in the past, they have received discs from clients that are copy protected and ready for replication. Is this possible? Can I burn these type of discs with DVD Studio Pro and a built in burner?
I would think that this would be the DDP image with the CSS keys included. I dont believe there is any way to output a playable DVD that has CSS to a DVD-R on any authoring system. Even if there was you cannot premaster a DVD-Video with CSS at any replication facility.
-Luke
I think that pretty much sums it up.
Ed

Port forwarding for external access to VNC server on multiple machines

I will have 10 PCs connected to the WRT54GL wireless AP. I am testing with 1. It has a static addresses 10.155.22.51. It is running a VNC server at port 5951.
If I set my VNC client up to access 10.155.22.51:5951 it works through the WRT54GL wireless AP.
I set the WRT54GL port forwarding to 5951 - 5951, set the IP address to 10.155.22.51 and enable. The external address of the AP is 10.155.0.29 on the company LAN.
So I set the VNC client to access the AP address with the VNC port, i.e. 10.155.0.29:5951. I expect the AP to change the address to 10.155.22.51:5951. This does not work.
Note: the problem could be that the AP is going through NATting because I can also access it at 10.155.22.9 along with all the other PCs on that LAN, i.e. I can access the LAN directly from elsewhere on the company net.

You can try changing the IP of the AP manually ... connect it to the Computer ..... access the setup page using http://192.168.1.245 .... use password as admin ....
Configure the IP settings first ...
Again login with new IP address .... configure wireless settings .....
Power down the AP & then the router ....
Wait for few minutes .... then power on the router ...first then the AP ...

Ports Required for SMTP access from DMZ

We have a Windows 2000 Adv Server on a DMZ interface of a PIX firewall. We are using native Windows SMTP services as a Front End server for Exchange mail. Our Exchange server has a SmartHost entry that sends outbound mail to the server on the DMZ. Our MX record points to the server on the DMZ for inbound traffic.
We originally allowed DNS resolution and SMTP (Port 25) traffic to the server. We've done this numerous times from the Internal interface of the PIX. Yet, there apparently is at least one other port that needs to be opened up because the mail stays in the Queue of the SMTP server on the DMZ. We got around the problem by opening up all outbound ports from that server.
My question is: "Does anyone know what ports are required for an SMTP server to work on a PIX DMZ?"
Thanks

Should just be TCP/25 and probably DNS (UDP/53). Probably the easiest way to figure out what other port it's using is to look at the active connections from this going through your PIX.
Let's say the IP address of the mail server is 10.1.1.1. Doing:
sho conn | include 10.1.1.1
will give you all the connections. This will tell you where it's connectig to and on what ports. The output will look something like:
FW1(config)# sho conn | incl 10.1.1.1
UDP out 10.2.2.1:17127 in 10.1.1.1:10655 idle 0:01:23 Bytes 1000
UDP out 10.2.2.1:18733 in 10.1.1.1:10477 idle 0:01:38 Bytes 1000
UDP out 10.3.3.2:18429 in 10.1.1.1:10789 idle 0:01:10 Bytes 1000
The numbers after the colons are the port numbers on the connection. Of course yours will show TCP and port 25 (and something else hopefully), but you get the idea.

Can Prime Infrastructure 2.0 enable port 8080 for Browser access?

Similar Messages

Maybe you are looking for