Can printer connect to more than one network?

Hello.
I just bought the wireless HP deskjet 3050 printer. I've connected it to the internet (network) and it's working perfectly. Is it possible to connect to more than one network? We have more than one internet line in the house so I was wondering if I can set it up for both lines. I understand that I can print with multiple computers on the same network (and I am able to do so), but how about on different networks?
Thanks.

No, it only has one network connection device so can only connect to one at time, sorry.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

  • Connecting to more than one network

    Can I set up the 8620 to connect to more than one network?  If so, will the printr connect to whatever network the computer is using?  

     Welcome to the HP Community Forum. If I understand your inquiry, the following might be helpful. It is possible to switch the default printer when you switch networks. Example here:Set Printer as Default See section titled Method 3 – Set the Printer Default when you change Networks  When you see a Post that helps you,Inspires you, provides fresh insight,Or teaches you something new,Click the "Thumbs Up" on that Post. Click my Answer Accept as Solution to help others find Answers.
     

  • Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????

    Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????

    Hmmmm.
    If you reset the AirPort Extreme by holding in the reset button for 9-10 seconds and then releasing, the AirPort should be back in default settings which would allow mutliple computers to connect to the LAN ports on the AirPort.
    Power off the cable modem for now and leave it off at least 15 minutes.
    With the AirPort Extreme still powered on, hold in the rest button on the back for 9-10 seconds and release. Allow a full minute for the AirPort Extreme to restart to a slow, blinking abmer light.
    Then, power off the AirPort Extreme.
    Check to make sure that the Ethernet cable from the modem is connected to the WAN "O" port on the AirPort Extreme.
    After the modem has been powered off for at least 15 minutes, power it up and let it run for 5 minutes by itself.
    Now, power up the AirPort Exteme and let it run for 2-3 minutes
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Connect an Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Express
    Click on the AirPort Exteme, then click Continue to follow the guided setup tp configure the AirPort Extreme.  You can use the same wireless network name, password, etc that you used before, or set up a new name and password, etc.

  • Can I connect with more than one iTunes acct

    Can I connect with more than one iTunes acct

    Laxman25 wrote:
    If its multiple apple id's on one computer you can't because you have to log out of one and login on another.
    I've only got one ID so I can't test but Winston says you can be signed into iTunes with multiple AppleIDs (i.e authorise iTunes for more than one ID content) at the same time, and that even different account content will stream so long as Home Sharing ID in iTunes matches AppleTV Home Sharing ID.
    AC

  • How can I connect to more than one computer from external ip

    Hi
    I have been using remote desktop for some time and have a port forward set so I can connect to our mail server from anywhere else externally from my macbook pro, but how can I connect to other macs in the office when there only seems to be the two ports available for use 5900 and 3283. I can only port forward to one computer? How can I connect to multiple computers when not within the same network? are there other ports available?
    Cheers
    Tony

    If your workstations get their addresses from an NAT device rather than being "real", the ports also need to be forwarded in the router to the workstation's internal IP address.  ARD uses port 3283 for the reporting and updating function, so if your Macs are getting their IP addresses through NAT, since you can only forward a port to a single workstation, you can only get reports, push package/files to etc. for a single workstation.
    ARD uses the VNC protocol for observation and control, though, and there are a range of IP addresses for that protocol, starting with 5900. ARD uses 5900 by default, so that port would be forwarded to the first workstation. You would, I believe,  need to install third-party VNC software on the systems (since the ARD client cannot listen on any port other than 5900 while other VNC systems can be set for other ports such as 5901, 5902, etc. You would then  forward 5901 to the second workstation (and on to 5902, 5903, etc.). You can then use the following information:
    http://docs.info.apple.com/article.html?path=RemoteDesktop/3.0/en/ARDC715.html  to connect.
    The only other options are: 1) to run the ARD administrator on a workstation on the network, and then take control of that system from outside, either via VNC or another copy of ARD, or 2) set up a virtual private network (VPN) so that when you connect from outside, your admin system is officially part of the local network.
    Hope this helps.

  • HT5622 Can Face Time be used to connect with more than one person at a time?

    Can I connect with more than one person at a time when using Face Time?

    You mean like a conference call?  No, unfortunately.

  • Connectivity to more than one ERP

    Hi experts!
    Does anyone know whether CRM 2007 can be connected to more than one ERP?
    Thanks in advance.
    Almudena

    Hi Almudena
    Yes, Certainly CRM 2007 can be connected to more than one ERP backend systems. These systems can be SAP EPR systems or may not be SAP ERP systems or can be a combination of SAP & Non SAP ERP systems.
    The exchange of information between SAP CRM and other components, such as SAP BW and ERP back-end systems, occurs over the CRM middleware.
    The CRM Server contains the CRM middleware, which handles the data exchange with internal applications and external major components, such as an SAP ERP and/or non-SAP ERP systems used as the back-end. The CRM middleware can exchange messages with Non u2013SAP ERP system via standard interfaces, for example, XML u2013 SOAP.
    If you want to link more than one CRM system or more than one ERP system, see Notes 640570 and 853430.
    The data exchange between the CRM Middleware and external systems is performed via adapters. The adapters map and convert data between various formats.
    Hope I have answered your question. Please give rating to my answer if you find it useful.
    Regards
    Dinesh

  • Express won't connect to more than one devise

    I got an airport express used and it won't connect to more than one device. First only my MacBook and would not allow my iPad on. And now the playstation is connected and the MacBook can't get Internet. Any advise?

    Kyle-BHD wrote:
    I got an airport express used and it won't connect to more than one device.
    Please identify the model number of your AirPort Express (A1084, A1088, A1264?), the brand(s) and model number(s) of your other networking equipment, and how it's all connected. When you launch AirPort Utility and put the AirPort Express into "manual setup" mode, what value do you see for "Connection Sharing" in the Internet panel, "Internet Connection" tab?

  • Can I back up more than one mac to the time machine:

    Can I back up more than one Mac to a time machine? I have a laptop and a Mac Desktop computer can I back up both on the same Time machine

    Absolutely.
    However, quoting from ASC contributor Pondini's excellent Time Machine FAQ:
    It is advisable, though, to partition an external disk that will be connected to your Macs into one volume for each Mac ...

  • I have a PC, Windows 7 x64. I installed a plug-in in Elements 13. I tried to installed another plug-in. It replaced the first plug-in . Can't I have more than one plug-in at a time??? If so, how?

    I have a PC with Windows 7 x64. I have Elements 13. I installed a plug-in (Topaz) which appeared under the Filter Menu.
    Then I tried to install my new Canon Printer software plug-in which put it under FILE > AUTOMATION TOOLS. However, when I tried to use TOPAZ under the FILTER MENU it was gone. In other words, the Canon printer plug-in replaced my Topaz plug-in. When I reinstalled the Topaz plug-in, it replaced the Canon Printer Plug-in.
    QUESTION: Can't I have more than one plug-in installed in Photoshop Elements 13 at a time? So that the Canon printer plug-in is in AUTOMATION TOOLS, and the Topaz plug-in is under the FILTER menu?

    Have a look at this thread.
    http://discussions.apple.com/message.jspa?messageID=2369954#2369954
    Before you try some of the suggestions bear in mind that your iPod is still under warranty.

  • Simultaneous connection of more than one unit of GPIB device

    Dear all out there,
    Would anyone has any idea/ solution in programming of ATE that makes Simultaneous connection of more than one unit?
    What's the better, if not the best, way of initialisation, acquisition and report generation for such system? without significant delay incurred.
    For instants,
    1. Initialise X number of, say, Agilent 34401A multimeter (GPIB)
    2. Acquiring of meter readings from each meter, limit check and write to respective report
    Any idea/ sample code/ solution is very much appreciated.
    Regards
    ian.f k
    Ian F
    Since LabVIEW 5.1... 7.1.1... 2009, 2010
    依恩与LabVIEW
    LVVILIB.blogspot.com

    albert geven wrote in message news:<[email protected]>...
    > The connection of multiple multimeters to the gpib bus is normal, the
    > only thing you need to do is switch them each to a unique address on
    > this bus.
    > Your program can best initialise all multimeters once in the beginning
    > of your program and read out those meters when appropriate.
    With many instruments there are two types of "initialise."
    One type, which is a reset, choose range, etc., as you suggest can
    be done at the beginning of a program or section of a program.
    However, the other type of initialize is to sent the SCPI INIT command
    to the instrument. This command tells the instrument to take a measurement
    (or scan of measurements).
    When dealing with multiple multimeters, there are at least 2 ways of
    handling measurements. The slow way deals with one instrument at a
    time -- using the SCPI commands INIT, wait FETCH?, or perhaps just READ?
    sent to each instrument. It is slow because each instrument must wait
    for the previous instrument to finish before it can start.
    The better way is to set up each instrument for the desired measurement.
    If simultaneous triggering is needed, either use some type of external
    trigger or BUS trigger if the instrument can use it. After all instruments
    are set up, issue the INIT command to each instrument, then trigger.
    when all measurements are completed, use the FETC? command to get the
    results from each instrument. Note that there may be Plug&Play drivers
    to issue these commands for your instrument.
    [email protected]
    www.CompleteTest.com

  • Connect to more than one database?

    Hi,
    Is there a way to connect to more than one database from Oracle form (one form)? If yes, what's the best practice to do it?
    Saad,

    hi
    u can modify Tnsnames.ora for that
    example:
    test1 =
      (DESCRIPTION =
        (ADDRESS_LIST =
          (ADDRESS = (PROTOCOL = TCP)(HOST = IP Address)(PORT = 1521))
        (CONNECT_DATA =
          (SERVICE_NAME = test1)
    test2=
      (DESCRIPTION =
        (ADDRESS_LIST =
          (ADDRESS = (PROTOCOL = TCP)(HOST = IP Address)(PORT = 1521))
        (CONNECT_DATA =
          (SERVICE_NAME = test2)
      )

  • While connecting to more than one database

    what shold i do while connecting to more than database...
    shold i implement it using serializable class
    or shold i pass the connection object a session variable
    give me some exaple for connecting to more than one database..
    sreekanth

    Sometimes you can use Connection.setCatalog(...) to switch.

  • Can not color label more than one file at a time

    Hi,
    I've had this problem since 10.6.6-ish, i can not color label more than one file at a time in the Finder.
    Wether i select two, twenty or twohundred only one file gets color labeled.
    It doesn't seem to matter if i assign a color label through the File menu or right click > label.
    Figured a re-install might fix this but it hasn't (even a clean install without restoring any kind of backup).
    Does anyone else have this issue and/or a fix for it?
    Thanks,
    Jay

    Aaaaanyone ?

  • My sister has a mac and i want to update my phone onto the computer but i dont want her to see all my stuff can you somehow have more than one itunes account on the same computer so my stuff with save?

    my sister has a mac and i want to update my phone onto the computer but i dont want her to see all my stuff can you somehow have more than one itunes account on the same macbook so my stuff with save?

    How to use multiple iPhone, iPad, or iPod devices with one computer. The only way is for you to have a separate user account to log into on that computer.

Maybe you are looking for

  • Issue in dbms_metadata.set_transform_param , SQLTERMINATOR Property

    Hi, I am using the dbms_metadata to get the DDL for all the objects in a particular schema. DDL is retrieved without any issue, but the SQLTERMINATOR  is not added in end of any DDL. The property used is   dmsf := dbms_metadata.session_transform;   d

  • Form 16 error

    Hello Friends We are facing an issue with Form 16 in ESS. After raising an issue with SAP, they have asked us to install a note for R/3 system in order to have TAN based reporting for Form16.  After installing this note we are able to run Form 16 in

  • Photoshop elements 10 freezes and won't allow me to sign in.

    I've installed photoshop elements 10. Serial # is accepted. I try to open the application on my mac and it freezes. No sign in and I have to force quit the application. Does anyone have any suggestions because Chat support is apparently only for the

  • How do I restore one contact from my Time Machine?

    How do I restore one contact from my Time Machine?

  • Photo Booth Recording Movie Stutter & Unintentional Stops

    I'm trying to record video with my Photo Booth and when I press record, the sound that makes a click right after the last second of the countdown stutters about four times and then begins to record. Even if I record two minutes or so, when the video