Can't access c3550 over network

Hello!
I'm having trouble getting my c3550 to communicate on my network. I believe that I've set it up correctly, but there's obviously something wrong. I would appreciate any insight you may have. My network is currently 192.168.0.0/22 without VLANs. Here's some device output:
C3550_01#show running-config
Building configuration...
Current configuration : 2595 bytes
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname C3550_01
enable secret 5 $1$dwg9$2H2g.v8NcqqLl9lR9axK8.
enable password 123456
ip subnet-zero
spanning-tree mode pvst
spanning-tree extend system-id
interface FastEthernet0/1
 switchport mode dynamic desirable
 no ip address
... (0/2 - 0/23 have identical output)
interface FastEthernet0/24
 switchport mode dynamic desirable
 no ip address
interface GigabitEthernet0/1
 switchport mode dynamic desirable
 no ip address
interface GigabitEthernet0/2
 switchport mode dynamic desirable
 no ip address
interface Vlan1
 ip address 192.168.3.251 255.255.252.0
ip default-gateway 192.168.3.254
ip classless
ip http server
line con 0
 exec-timeout 0 0
line vty 0 4
 password 123456
 login
line vty 5 15
 password 123456
 login
end
C3550_01#show interfaces vlan 1
Vlan1 is up, line protocol is up
  Hardware is EtherSVI, address is 000e.d78f.ca80 (bia 000e.d78f.ca80)
  Internet address is 192.168.3.251/22
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 15:23:05, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 2
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicast)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
C3550_01#show vlan
VLAN Name                             Status    Ports
1    default                          active    Fa0/2, Fa0/3, Fa0/4, Fa0/5
                                                Fa0/6, Fa0/7, Fa0/8, Fa0/9
                                                Fa0/10, Fa0/11, Fa0/12, Fa0/13
                                                Fa0/14, Fa0/15, Fa0/16, Fa0/17
                                                Fa0/18, Fa0/19, Fa0/20, Fa0/21
                                                Fa0/22, Fa0/23, Fa0/24, Gi0/1
                                                Gi0/2
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup
VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
1    enet  100001     1500  -      -      -        -    -        0      0
1002 fddi  101002     1500  -      -      -        -    -        0      0
1003 tr    101003     1500  -      -      -        -    -        0      0
1004 fdnet 101004     1500  -      -      -        ieee -        0      0
1005 trnet 101005     1500  -      -      -        ibm  -        0      0
Remote SPAN VLANs
Primary Secondary Type              Ports
C3550_01#

Thanks for the response!
If I understand your questions correctly,
1 - I'm attempting to access the switch across my network (via wired ethernet) from my admin workstation. The switch does not respond to network discovery attempts, including ping.
2 - I'm unable to ping the switch or any device connected to it from my admin computer. Also, devices connected to the switch can't ping each other, the switch, or any network IP.
3 - The only access I have right now is through the serial console.
I should probably also mention that this switch is being configured on my bench before deployment - if I can get it to work.

Similar Messages

  • Can't access Mac over network since Mavericks update

    Help! Since the update to Mavericks I can't access my iMac over my home network using my Nexus 7 tablet. I used to do it flawlessly right before I updated from Mountain Lion.
    I was using ES File Explorer to browse my shared folders on my Mac from my Android Tablet right away and now I keep getting asked for a username and password to connect. I type it correctly but still not able to connect. I tried other file browing apps for my tablet (File Manger, AndSMB,...) but still unable to connect. The apps can scan my network and find the server address (iMac) but can't get access to it.
    I must say that the Tablet can access the internet so it's not Tablet network settings related.
    I tried the workaround found here http://cammodude.blogspot.ca/.  Still not working. Any suggestions?

    Try going back and checking the step 3 on the linked instructions for remote login where it mentions:
    Step 3: Now enable “Remote Login” in the Sharing menu of System Preferences.
    Read more: http://www.shoutpedia.com/transfer-files-mac-os-x-mavericks-android-phone-wifi-e asy-way/#ixzz30iEam8MC
    That's the part that will allow it.  I've got "Remote Login" checked there' and and then make sure you have whichever user(s)/groups added for the login you're using.  I have that set to Administrators and on then on my phone I have it set up with computer IP, port 22, my computer username which is a First Last type format with the space...whatever it normally says on your login screen on your computer or when you get prompted to allow software installs etc. and then the password.

  • Windows 7 media center MCE plug-in & Elements 8 - can not access catalog over network

    Hi,
    I have Elements 8 installed on windows 7 and want to use the Microsoft Media Center photoshop plugin to view photographs and slide shows held on a network share.  How do I configure the plug-in to find the catalog on the share ( at address  P:|Pictures ).
    All I can see is an entry for "My Catalog" on screen and a small number of black thumbnails.
    Thanks
    Kilraughts

    For some reason when using the "certified" MCE version of the Forceware drivers, after a short while all the buttons in the menus become "corrupted"
    The simple solution: use regular XP/2000 version of Forceware drivers. They still work perfectly in MCE2005, and the graphical corruption doesn't appear.
    nVidia Drivers
    EDIT: this problem appears to have been corrected in the recent Rollup 2 Update

  • How can i access my wireless network?

    how can i access my wireless network at home?

    Does your iPad see your WiFi network - Settings>WiFi>Tap your network name, enter your password and tap join.
    If the iPad isn't seeing the network, try rebooting the router - unplug it for about 30 seconds and then plug it in again.

  • Verizon Chat advises pdf attachment non-download from AOL email is a software problem and directs me to Apple Support. I see "can't access cellular data network" in an instant before the file's icon turns into the file's name.

    Verizon Chat advises pdf attachment non-download from AOL email is a software problem and directs me to Apple Support. I see "can't access cellular data network" in an instant before the file's icon is replaced by the file's name. In Inbox three emails in a row show there is an attachment. My iPad 3rd gen. runs 7.1.

    You have Acrobat Pro on your system. It will try to open PDFs, and of course it will fail. You must uninstall it. Then, you will need a PDF reader. So install Adobe Reader. That seems quite simple, but perhaps something is wrong. If anything goes wrong with these two steps (1) uninstall Acrobat Pro (2) install Adobe Reader, then please let us know the details.

  • VPN - can't access internet over VPN

    Hi,
    I have an issue with VPN.
    For my work I need to be able to log into my office network remotely and then access remote desktop connection from within my work network.
    This won't work unless I am accessing the internet from inside the VPN.
    I have got this working on a PC, just had to select "Use default gateway on remote network" and now when I access the VPN on a windows laptop I am accessing the internet over the VPN.
    When I connect to the VPN on the Mac I can access the network, email server, file servers etc, but can not access the internet through the VPN.
    I have tried:
    - changing the service order
    - ticking and unpicking the send all traffic over VPN setting
    I can get to the point where I can access my work network over the VPN while also accessing the internet over my wifi but cannot get it so I can access the internet over the VPN connection. It is a PPTP VPN.
    Does anyone know how I get my Mac to use the default gateway on the remote network?

    If this server is behind a (NAT-) router you need to turn on "ipforwarding only" in Server Admin NAT configuration otherwise the server wont route packets beyond it's subnet.

  • Can't access Windows 7 network nor homegroup via router or ad-hoc

    I have a really annoying problem. I have 2 clean computers. They were formatted and Win 7 ultimate was installed on both computers. They have a PCI wireless card (D-Link DWA 525). Their hardware is identical, same motherboard, etc, beside the "server"
    is pentium 4 and the "client" is celeron.
    We have 2 routers and 1 modem. The first router, Airport Extreme, act as DHCP server, and provides the wireless network. The second router (TimeCapsule), connected thought ethernet to the first router, extends the wireless network (act as a bridge). I can connect
    to the network and the internet works fine.
    The problem is with the local network.
    I can see both computers on the network tab. I can ping both by IP and by name. I made a Homgroup on the computer "Server". The computer "client" joined. I can see the libraries. Both computer's firewall are disabled. All firewalls from
    the routers and the modem are disabled.
    Double-clicking the library on the Homegroup does nothing. Trying to access the shared folder by \SERVER or by the network tab gives error "network path not found".
    Basic settings, like file and sharing, etc, are on. Password sharing is off. Encryption is 40 - 50 (not the 128, I don't remember the specific number).This is both for Home and Work and Public networks.
    Because I couldn't access the network, I decided to make an ad-hoc. Same problems. Even with static IP (192.168.0.1 [server] and 192.168.0.3 [client], 255.255.255.0 subnet) and NetBios forced at enabled.
    I just can't make it work. I have tried a lot of info from here and other forums, but nothing has work. The worst is that another PC will join the network, but I haven't do it yet just because I can't make these PCs to work. As a test, I did put the other PC
    in the network (Win 7 Home), and the same problem applied.
    All the computers can see them in the Network tab, ping either ways with both IP and name, but when trying to access the pc over network, it gives network path not found error.
    Yes I have shared files.
    Troubleshooting both Homegroup and Network finds nothing wrong or just can't fix the problem.
    Please help!

    Hi,
    I tried and received only errors (i don't remember know which ones).
    However, I plugged the PCs via ethernet, let automatic IP address, and now I can access the network from both computers. Homegroups doesn't work because the network is public, but that isn't a matter right now, because I can access the files.
    This makes me thing if the problem is the network adapter. In the Advanced tab on Device Manager Properties, I have the follow options, which I don't have idea what are they for:
    AC_BE support APSD [disabled]
    AC_BK support APSD [disabled]
    AC_VI support APSD [disabled]
    AC_VO support APSD [disabled]
    APSD capable [disabled]
    Multimedia/Gaming Environment [Enabled]
    Roaming Sensitivity [Medium]
    WMM Capable [Enabled]
    Do you think some of that options are interfering?
    Thank you

  • I can't access my USB network drive connected to my router.

    I have a G5 that I was running Tiger, and could easily access a usb network drive connected to my router. As soon as I upgraded to Leopard, I sporadically get access, but usually not.
    I just purchased an iMac with Snow Leopard and then upgraded to Lion, but I have never had access to this drive.
    I can't get access with either Mac now, but I have no problem accessing the drive from a PC on the same home network, so I know the drive is connected properly, and is working properly.
    Any thoughts how to access this drive from my Macs?

    Let's say that the name of your drive is Hard Drive
    Check using AirPort Utility to get the IP address of your AirPort Extreme, for example you see that it is 10.0.1.1
    You'll need to know the device name for the AirPort Extreme. This is not the wireless password, it's the device password.
    On the PC, open My Computer
    Click on Tools and select Map Network Drive.
    Select the drive you want, "Z" for example
    On the next line for Folder, type in
    \\10.0.1.1\Hard Drive
    Click Finish
    Type in your user name
    Type in the device password for the AirPort Extreme

  • Changed OVM IP.... cannot access guests over network.

    I moved my test OVM server from one datacentre to another. This necessitated a change of IP address for the server and the guests. I was able to update the servers details in the OVS VM management app and all is well. The VM management server did not move. I can start and stop the guests etc etc. However I can no longer access the guest over the network. I can access the guests when I am logged on to the OVS server, I can ping, ssh and do all the things you would expect, I can even ping from inside one guest to another guest so there is, fundamentally, nothing wrong with the guest setups that I can see. It would appear as though packets to/from the guests are not being 'forwarded' or some such. I have triple checked all my network settings from OVS server and 2 guests and cannot get it to work. From inside a guest if I ping the gateway address I get no answer.
    Is there something tucked away in the bowels of the xen configuration that still has some old settings ?
    Surely I wouldn't have to re-install just because I changed the IP ?
    Any help would be appreciated.

    Is the MAC-address for the Xen-bridge in vm.cfg on the VM Server identical to the HWADDR in /etc/sysconfig/network-script/ifcfg-ethX ?

  • Password to access TL96 over network

    Hi, when I browse the IP of my TV over my LAN I am prompted for a username and password. What are the defaults?
    Thanks

    Hi
    If such default password and user name would be required, you should be able to find it in user manual.
    But Im wondering why you access the TV over the IP?
    You can connect the TV to the home network and the Toshiba TV menu support some options to access the network. In Media Player you can find the USB media player and Network Media Player. To get access to the video and picutres you have to use the 2nd option (Network Player)

  • Having problem accessing MacMini over network with PC's Windows 7

    Hi all,
    I have a Mac Mini with 10.6.x
    Onec in a while, especially when restart Airport Extreme for upgrade or something else (both are connected with ethernet cable cat5e) ALL PC's on the network having problem accessing Mac Mini Server while All MACs are fine and can access all folders no problem. Usually takes about 3-4 min for PC to connect to server. Then  once it is connected (it loads all folder and files in that current window on the PC) i can go from folder to folder with no delays. However if i close the window with all folders then again i have to wait for around 3 min. to load everything all over again. AFP and SMB are ON. Today i made an experiment and turned SMB off and the problem still excist with the difference that after 3-4 min delay no folders were shown.
    It seems that the PCs have hard time establishing connection with the server which is weird that Macs don't have that problem. It must be something with the setting of Mac MIni. Other wise i have no problem accessing Internet so the routher is working fine. DHCP is ON on the AP Extreme.
    I came across as i was searching for this issue and it seems that authentication - Golden triangle or whatever is called - might be the issue in the whole mess. Do you guys think that this might be the case ?
    The only way i have found out to help is to restart the Router and Server and that usually fix the problem  .
    Could you please help me figure what is going on there?
    Here is the original thread: https://discussions.apple.com/thread/3867559?tstart=0 ( i think i posted in the wrong forum )

    The specified changeip -checkhostname command does not make changes to your configuration. 
    To research the command (and that's entirely your perogative), please use Google or Bing to search for previous discussions and details, or review the provided man page documentation for the command.  (Launch Terminal.app (folder Applications > Utilities) and issue the command man changeip.  You'll see something like this:
    $ man changeip
    changeip(8)               BSD System Manager's Manual              changeip(8)
    NAME
         changeip -- Change service configuration files with hard-coded IP addresses
    SYNOPSIS
         changeip [-v] [-d path] old-ip new-ip [old-hostname new-hostname]
         changeip -checkhostname
         changeip -h
    DESCRIPTION
         changeip is used to manually update configuration records when a server's IP address or hostname changed in a way that affected services were unable to properly process, for example when the server is behind a NAT device and the WAN identity changed.  ...
    Given your response and your concern, consider creating a backup of your disk.  Shut down, boot the installation DVD, and use Disk Utility (from the Utilities menu) in the second screen of the installation process to copy your disk contents to an external storage device.  (Time Machine isn't as good at getting a backup of a server as is a clean backup created while shut down.)  There are descriptions around that detail how to create this backup using Disk Utility.
    There is no DNS server implemented in the Airport Extreme.  The Airport Extreme forwards DNS requests to a DNS server elsewhere.  Few gateway devices contain DNS servers; that these devices request a DNS address tends to be confusing, too.  That address is solicited from the user for use in the DHCP server that many of the available gateway devices provide.
    There is no need for a DNS forwarder, particularly if your server is configured for your LAN.  (Adding a forwarder adds another hop into the whole translation process.  That configuration and that extra hop can be useful when the intermediate DNS server is providing specific, enhanced DNS-related functions, such as security monitoring and logging, or providing a "nanny filter" mechanism.)
    If you are running DNS services on your LAN, then your Airport Extreme DHCP server should be configured to pass out the IP address of your DNS server.
    It would appear that your local box has the default self-hosted DNS, and is not configured to serve LAN DNS (other than for itself).  That's good.  Accordingly, it'll likely be getting good DNS from itself, but will not be getting translations for other hosts on your network.  That's not so good.  When DNS responses are not available, you'll get DNS-level timeouts, and those are usually around 30 seconds each.
    Check your server logs for messages related to the failed connections, and check the Windows file service logs for any errors being generated by the file service.  The log information is most easily available from Console.app, which is a utility in Applications > Utilities folder, or from the Server Admin tool (Applications > Server folder) for DNS, and for the file server component.
    The above is probably going to read like a wall of unfamiliar jargon, so please ignore this and my previous response here, and I'll leave it to somebody else to assist you here.

  • What to do if you can't access a wifi network and showing you message that your airport has a self-assigned IP and cannot be connected to the internet?

    Hi,
    i am currently using 10.6.8 snow leopard
    i usually access internet through my broadband modem and wifi at home.
    i've been using our home wifi network for almost 1 week now (since it's new) and almost everyone at home use it as well.
    and im using my broadband everytime i go out.
    this last week, i went to a vacation and i use the wifi connection of the hotel where i stay in.
    my connection works fine and so i don't use my broadband anymore.
    then i got home..
    when i got home..  i tried to connect to our home wifi network again .
    like what im doing before, im clicking the airport icon on the top of my desktop,
    and since my airport is always on, the next step that im doing is to click the preferred network that i want to join and put the password on it.
    this is perfectly working in my macbook before i left.
    but now , it's not working to my laptop anymore! i can't connect to it!
    after putting the password and hitting the enter, the airport icon at the top will run, however after seconds it showing gray color with exclamation point on it!
    the alert is showing : No internet connection
    but the network i joined is still checked and showing full signal !
    i tried checking my Network under system preferrence and the airport tab in the left corner is showing me a message that
    my airport has the self-assigned IP address 169.***.****.** and will not be able to connect to internet!
    i don't know what happen and i dont understand why is this happening since everyone at home can still use and access our home wifi !!
    it's the same network that i'm trying to connect to anyway!
    i tried using my broadband instead to connect online and it works fine!
    but everytime i try to connect using wifi at home , again i cant connect!
    anyone can tell me what's going on?
    i haven't try joining other network anyway! but i'm planning to do so..
    can some one help me please??
    showing me a message that
    my airport has the self-assigned IP address 169.***.****.** and will not be able to connect to internet!

    and now, when i tried to check again my network preference below the airport tab is showing a message that
    "my airport does not have an IP address and cannot connect to the internet!"
    then after seconds it will goes back to the first message that
    "airport has the self assigned IP address etc....."
    i don't know whats going on now!
    airport tab is not showing green color anyway! i'ts always in yellow!
    i tried turning it on and off but nothing happen! HEEELLLLPP!!!!

  • GnuPG: Can't access keyserver over HKPS

    Accessing a keyserver over HKP works, but HKPS doesn't. I'm using GnuPG 2.1.1-1.
    # HKP - works
    $ gpg --keyserver hkp://hkps.pool.sks-keyservers.net --search-keys 9741E8AC
    gpg: data source: http://srv01.secure-u.de:11371
    (1) Pierre Schmitz <[email protected]>
    2048 bit RSA key 9741E8AC, created: 2011-04-10
    # HKPS - general error
    $ gpg --keyserver hkps://hkps.pool.sks-keyservers.net --debug 1024 --search-keys 9741E8AC
    gpg: reading options from '/home/florian/.gnupg/gpg.conf'
    gpg: enabled debug flags: extprog assuan
    gpg: DBG: chan_3 <- # Home: /home/florian/.gnupg
    gpg: DBG: chan_3 <- # Config: /home/florian/.gnupg/dirmngr.conf
    gpg: DBG: chan_3 <- OK Dirmngr 2.1.1 at your service
    gpg: DBG: chan_4 <- # Home: /home/florian/.gnupg
    gpg: DBG: chan_4 <- # Config: /home/florian/.gnupg/dirmngr.conf
    gpg: DBG: chan_4 <- OK Dirmngr 2.1.1 at your service
    gpg: DBG: connection to the dirmngr established
    gpg: DBG: chan_4 -> KEYSERVER --clear hkps://hkps.pool.sks-keyservers.net
    gpg: DBG: chan_4 <- OK
    gpg: DBG: chan_4 -> KS_SEARCH -- 9741E8AC
    gpg: DBG: chan_4 <- ERR 1 General error <Unspecified source>
    gpg: error searching keyserver: General error
    gpg: keyserver search failed: General error
    gpg: DBG: chan_4 -> BYE
    gpg: secmem usage: 0/32768 bytes in 0 blocks
    Tried this with both an empty dirmngr.conf and the following (from the bottom of https://sks-keyservers.net/overview-of-pools.php):
    hkp-cacert /home/florian/.gnupg/sks-keyservers.netCA.pem no-honor-keyserver-url
    The gpg.conf is completely empty.
    Any idea what's going wrong here?

    @clfarron4: So you didn't change gpg.conf from the default (sorry if I understood this incorrectly)? If so, I think HKPS isn't actually used. See this output, using default gpg.conf:
    ~ mv .gnupg/ gpg
    ~ gpg
    gpg: directory '/home/florian/.gnupg' created
    gpg: new configuration file '/home/florian/.gnupg/gpg.conf' created
    gpg: WARNING: options in '/home/florian/.gnupg/gpg.conf' are not yet active during this run
    gpg: keybox '/home/florian/.gnupg/pubring.kbx' created
    gpg: Go ahead and type your message ...
    ^C
    gpg: signal Interrupt caught ... exiting
    ~ gpg --debug 1024 --keyserver hkps://hkps.pool.sks-keyservers.net --search-keys 9741E8AC
    gpg: reading options from '/home/florian/.gnupg/gpg.conf'
    gpg: enabled debug flags: extprog assuan
    gpg: DBG: chan_3 <- # Home: /home/florian/.gnupg
    gpg: DBG: chan_3 <- # Config: [none]
    gpg: DBG: chan_3 <- OK Dirmngr 2.1.1 at your service
    gpg: DBG: chan_4 <- # Home: /home/florian/.gnupg
    gpg: DBG: chan_4 <- # Config: [none]
    gpg: DBG: chan_4 <- OK Dirmngr 2.1.1 at your service
    gpg: DBG: connection to the dirmngr established
    gpg: DBG: chan_4 -> KEYSERVER --clear hkps://hkps.pool.sks-keyservers.net
    gpg: DBG: chan_4 <- OK
    gpg: DBG: chan_4 -> KEYSERVER hkp://keys.gnupg.net
    gpg: DBG: chan_4 <- OK
    gpg: DBG: chan_4 -> KS_SEARCH -- 9741E8AC
    gpg: DBG: chan_4 <- S PROGRESS tick ? 0 0
    gpg: DBG: chan_4 <- S SOURCE http://206.176.170.195:11371
    gpg: DBG: chan_4 <- D info:1:1%0Apub:4AA4767BBC9C4B1D18AE28B77F2D434B9741E8AC:1:2048:1302428133::%0Auid:Pierre Schmitz <[email protected]>:1302428133::%0A%0D%0A
    gpg: data source: http://206.176.170.195:11371
    gpg: DBG: chan_4 <- OK
    (1) Pierre Schmitz <[email protected]>
    2048 bit RSA key 9741E8AC, created: 2011-04-10
    Keys 1-1 of 1 for "9741E8AC". Enter number(s), N)ext, or Q)uit >
    gpg: signal Interrupt caught ... exiting
    As you can see, this does work, but doesn't actually use the keyserver specified with --keyserver. It falls back to the one from the config, which uses an unencrypted connection (HKP). Also see http://lists.gnupg.org/pipermail/gnupg- … 29219.html:
    Gnupg sends the dirmngr the keyserver it should use with a KEYSERVER command.
    In dirmngr's debug output you can see that it sends KEYSERVER --clear <foo>
    and then another KEYSERVER command for each keyserver configured.
    In my tests it always used the last one.
    @jasonwryan: do you have any keyserver(s) specified in your gpg.conf? If yes, then HKPS might not work for you after all. You should be able to check with --debug 1024.
    Last edited by fwalch (2015-01-02 10:24:00)

  • Can you control when a user can have access to the network

    i want to set a time frame when users can be on network

    You do this using Timed Access in AirPort Utility.  It is possible to set daily time limits for each wireless device that connects to the wireless network.
    You can even have multiple rules for the same device. Example, a device could connect from 9 AM to 9PM Weekdays and from 9 AM to 11 PM on Weekends.
    For more information, click the Help menu at the top of the screen in AirPort Utility.
    Click AirPort Utility Help
    On the left panel of the next page, click on Setting up a Wi-Fi Network
    Select the following topics on the right:
    Control when a user can access your network
    Control access to your wireless network

  • Can't access favourites (in network)

    hi,
    when i open my network (shift,comand,k) my laptop won't let me access any folders in the 'favouties' tab on the left. Once i open a tab my laptop freezes and the window closes. PLEASE HELP

    Hi Juandi89,
    I had the same problem (i think?).
    We have a mac and another pc running windows 7 on our home network. After I upgraded to mavericks, when we tried to access files on my mac from the windows pc (as we stream media files from my mac onto the pc) it asked for a username and password to connect to my mac.
    For the life of us we couldn't figure it out. I tried setting back the SMB option as well and it didn't work for me either. I was in the process of backing up all my files to downgrade to a lower version of osx!
    But a friend told us to try entering the username and the password for my mac...and presto it worked! the windows pc can now see all the shared folders.
    I'm not sure if this is the same problem you're having but thought I would share what worked for me.
    If you have any questions (I'm not a techie tho), feel free to contact me.
    Marissa

Maybe you are looking for

  • Generating a report from RTF template using WSDL from ADF

    Hi, I am a newbie to ADF-BIP integration. I am using the wsdl http://<<ip>>:<<port>>/xmlpserver/services/PublicReportService?WSDL for generating a report from RTF Template in ADF. We are using Oracle Business Intelligence Publisher Release 11g (11.1.

  • Pdf files are not opening

    I have Adobe downloaded and in the past couple months the files haven't been able to open. It opens and it's black. I have re-downloaded it and it's still the same. Anyone have suggestions? It's a Mac.

  • How to instantiat​e a subvi multiple times parallely?

    Hi, I am developing an application which uses a set of input controls for performing a task. I have given eight such sets of these controls in the main vi. However, I want to provide user an option to add more sets if required by invoking a subvi (wh

  • CISCO AIR-AP1252AG-E-K9 is keep rebooting with no reason

    Hello I have an cisco AIR-AP1252AG-E-K9  and it reeboots randomly with no aparent reason this is the configuration aaa group server radius rad_eap server 10.10.1.2 auth-port 1645 acct-port 1646 aaa group server radius rad_mac aaa group server radius

  • How to use Photoshop With in My Samsung S3 Phone

    Today I have purchase Samsung s3 phone. I want to edit my picture in photoshop plz help me how to do?