Can't access the web setup utility - server says: level_15_access

I've been using a Dlink router, and wasn't getting any range on my network, so I tried to setup my linksys wrt150-n v1.1 router. I pressed the reset key for about 20 seconds, then unplugged both my modem (cable) and router, then plugged them back in. When I opened a browser window and typed http://198.162.1.1, instead of opening the setup page, I get a message saying "the server http://198.162.1.1:80 requires a username and password. The server says: level_15_access"
I left the user name blank, and used the default password admin, and that does nothing.
Tried resetting the router about 4 or 5 times with no luck. Any ideas about what I'm overlooking? I don't have the router setup CD that originally came with the router, and there isn't a downloadable file - I should be able to, and have in the past been able to just use the default IP and admin PW.
Thanks!
Solved!
Go to Solution.

Try a Hard Reset:
Hard Reset (aka 30/30/30 reset):
The following procedure will clear out the NVRAM and set dd-wrt back to default values:
With the unit powered on, press and hold the reset button on back of unit for 30 seconds
Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
Plug the unit back in STILL holding the reset button a final 30 seconds
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Similar Messages

How do I access the web-based utility

I just purchased a wireless router...WRT300N. I want to access the "web-based utility" in order to update the firmware.
How do I access the web-based utility...help!
Thanks.

Access the router’s web-based setup page.
For instructions, click here.
Linksys Easy Answer 4030, applies to WRT300N
Upgrading the Linksys Router's Firmware
Hope this helps,
Lilla
Westell 6100 modem/router; Linksys WRT54GL v1.1 router firmware 4.30.9; Linksys WPC54G v2 Notebook Card; CenturyTel DSL using PPPoE

TS3798 I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

amarilysfl wrote:
"Your disk could not be partitioned. An error occurred while partitioning the disk".
https://www.apple.com/support/bootcamp/
If you were using Apple's BootCamp and received this message, quit it and open Disk Uility in your Applicaitons/Utilities folder.
Select the Macintosh HD partition on the left and select Erase and Erase Free Space > Zero option and let it complete (important) this will check the spare space for bad sectors that can cause issues formatting partitions.
Once it's completed, try creating a partiton again in BootCamp.
If that doesn't work, then hold command option r keys down while connected to a fast internet connection, Internet Recovery should load (spinning globe) and then in that Disk Utility, select your entire internal drive and click > First Aid > Repair Disk and Permissions.
reboot and attempt Bootcamp again.
If you still get a error, it might be that you have OS X data on the bottom area where BootCamp partition needs to go. This would occur if you had the drive or computer for a long time or wrote a large amount of files to the drive and nearly filling it up and then reduced some, but it left traces in the area BootCamp needs to go.
To fix this
BootCamp: "This disc can not be partitioned/impossible to move files."
How to safely defrag a Mac's hard drive

I bought an EE sim, I've added a £15 smart pack but can't access the web

I bought an EE sim, I've added a £15 smart pack but can't access the web, it's an unlocked Galaxy S3, has anyone else had this issue?

Can you make calls & texts?
Have you selected a Network Operator under Settings / Connection / More Networks / Mobile Networks?

Can't Access the web administration page

Hello,
I have a new Linksys router that I installed a few months ago. I am trying to connect my PS3 using wireless. the PS3 sees the access point SSID, but keeps failing to connect. I have double/triple check the WEP2 key and it is correct. I am also having problems accessing the web administration page. I keep getting page not found. I don't think that I have access the web administration page since I set it up. I can ping the router, so I know that its up, along with getting out to the Internet, I have used NMAP and scanned the router, but only 10080 is open (PS3) port. I assume that the default URL for the web administration page is http://192.168.1.1. There is no port needed to put in the URL is there? Also, since NMAP showed no ports open does that mean that the web server in the router is not listen? If so how do I connect without having to reset the router?
I do have some Cisco Linksys app that shows a GUI of my network, but no adminisration help.
Thanks,

Who is your ISP..?
Are you able to go online on the wired computer...?
Make sure the computer is connected to the router on the Ethernet port and check the ip address first...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjust the browser settings....Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
Now,try to open the setup page again...

Can't access the web but can screen share and secure shell on my network???

Hi,
I don't know if this is relevant, but I installed a security patch along with a safari patch the other day and the next morning, I could not access the internet, however I can do things like screen share and ssh. I cannot however view internal websites on my network, whether I'm connected via airport or ethernet cable (attached to either time capsule or the modem directly). Whenever I try to go to a website in either firefox or Safari, I get a message saying I'm not connected to the internet and a "Network Diagnostics" button (which says it cannot fix my problem). Here is what I've tried:
-Repair Disk (everything OK)
-Repair Permissions
-Restart computer
-Turn Airport card off then on
-Restart modem and routers, one by one in daisy chain order (and then restarted computer)
-Tried different browsers
-Tried connecting directly to modem via Ethernet cable in addition to wireless
-Restored the System from a time-capsule backup from Sept. 6th (noticed the problem on the 10th)
-Turned off my firewall
-Created a new user account and tried it
-Let my computer remain off for a half hour
-Zapped the p-ram
Here's what I've confirmed I CAN'T do:
-Access the web via either Safari or firefox (haven't tried any other browsers)
-Access the Software Update Server
-My iCal calendars cannot access the webdav server
Surprisingly, here's what I've confirmed I CAN do:
-Ping other computers on my network
-Use the Screen Sharing App. with computers on my network
-Access the internet from every other computer on my network (4 of them)
-ssh to other computers on my network
I've been using my computer infrequently lately, and I'm not sure when the last time was I accessed the internet or for that matter when I performed the security patching, but I'm pretty sure it was within the last week and a half. I really don't want to try restoring from an earlier backup, but I'm reaching the end of my rope. Anyone have any other ideas? I'm fresh out.
Rob

The problem was either the Security Patch 2010-005 or the Safari update (though I don't have the version number in front of me). Note, I had ignored the iTunes 10 update. I assume that I must have miscalculated the date I performed the updates because the problem persisted after restore from a Sept. 6th backup off my time capsule.
I went to the Apple Store and they were able to restore full internet access by performing a 10.5.8 combo-update. When we ran Software Update at the Apple Store, the 3 updates were again there available for download, but I am going to ignore them all because of this issue. The people at the apple store agreed that it was the update which caused the problem.
Rob

Can't access the web-site in my home folder from the internet. Need help.

I am trying to publish a website from the Sites folder in my home directory. The website is made and I can access it from from every computer within my ethernet. But despite a couple attempts I made I can not get the website published on the internet.
I have an Airport Express station. Two Macs and one PC are using the ethernet. As far as I can tell the Airport Express station is directly connected to the internet. I live in a brand new apartment which has Lan outlets in every room next to the electricity outlets. I have a single designated internet IP address.
To open my computer to the internet I set the "Default Host Option" in the Airport Administrator Utility and selected the default three digits for the "Default Host option" IP address. Then I updated the Airport Express station, manually set the IP address in the Network preferences on my Mac to the "Default Host option" IP address and activated Personal Web Sharing in the Sharing preferences. By doing so I lost my internet connection. It turned out I still had the same IP address that I had before I selected Default Host Option.
As I understand with the Default Host Option I designate one IP address within the ethernet to receive all traffic from outside. But how do you now tell the Airport Express station which computer on the ethernet will be the host for the incoming traffic carrying the Default Host Option IP address? Apparently just setting the IP address manually in the clients computer Network preferences to the "Default Host Option" IP address doesn't tell the Airport Express station to change the IP address it has assigned to this client to the Default Host Option IP address.
In another attempt to make my website accessible on the internet I removed the Default Host Option and instead opened Public Port 80 and Private Port 80 for the IP address of the client computer in the Port Mapping tap of the Airport Administrator Utility. But again, no access to my website from the internet.
To access the website from within the ethernet I use the following web-link, which works fine:
http://192.xxx.x.x/~user/index.html
The internet of course doesn't see the 193 IP address. It only sees the Public IP address. Therefore I used the Public address instead of the Private IP address to connect to my website from the internet:
http://222.xxx.xxx.xxx/~user/index.html
But as I said, I still can't access the website from the internet.
I have the feeling that I conceptually don't understand something correctly. I would appreciate if somebody could help me with this problem.

See this article:
http://support.apple.com/kb/HT1866
Sometimes My Music does not show up in special folders in TweakUI.
If so, see this post:
http://discussions.apple.com/thread.jspa?messageID=1731188&#1731188##
If you would rather not mess with the registry you can often work round with a shift key start.
Hold down the shift key and start iTunes, keep holding down the shift key until you are asked to choose or create a library. If you already have one, navigate to your iTunes folder and choose iTunes Library.itl. Otherwise create a new library in My music.

TS1398 I can't access to the web pages thro' Wi-Fi, after switching on the wi-fi.But if I switch off the iphone andswitch on the phone then I can get the web pages.Daily I have to repeat this process to access the web pages.help to solve the problem.

I can't access the web pages thro' wi-fi,But if I switch off the phone and thenswitch on the phone again I am able to access the web pages.Daily I have to repeat this process.help to solve this problem.

Does using 192.168.1.1 get you to the web page?
Firmware Update Process
To safely update FW, I recommend doing the following: Download the FW file from the support site first.
Disable the auto update feature on the router.
1. Save router config to file first using IE or FF with all security add-ons disabled.
2. Factory reset the router with all other devices disconnected or turned OFF accept for 1 wired PC.
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=9d2ff02077f645679972a...
3. Reload or Update the FW using IE or FF. Just download the FW file to your local wired LAN PC.
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=0a6881b90224439b92c8d...
4. Factory reset the router and then set up from scratch first using the local log in link and test with out loading the saved config from file. Check to see if any problems are fixed before loading the saved config from file. Sometimes you need to set up from scratch with out loading the saved config file. Just safer that way.
PC Web Browser Configurations
What browser are you using?
If IE 8, 9, 10 or 11, set compatibility mode and test again.
Disable any security browser Add-ons like No Script and Ad-Block or configure them to allow All Pages when connected to the router.
Clear all browser caches.
Be sure to log into the local log-in account on the router first.

Can't access teaming web page

Hi, I've installed teaming 2.1 on a sles11 x64 virtual machine. I've used sun java jdk 1.6.21. After install I start the teaming server but then can't access the web page (I've used port 8080 in the URL). I used default network settings. I believe the mysql database has been created correctly. I think the problem is with Tomcat/java. I've included the output of tail --f catalina.out
/opt/novell/teaming/apache-tomcat-6.0.18/bin/catalina.sh: line 309: /usr/jre/bin/java: No such file or directory
Error occurred during initialization of VM
Could not reserve enough space for object heap
Could not create the Java virtual machine.
Error occurred during initialization of VM
Could not reserve enough space for object heap
Could not create the Java virtual machine.
Error occurred during initialization of VM
Could not reserve enough space for object heap
Could not create the Java virtual machine.
the path shown in the first line of this output is not what I specified for java during the installation of teaming (I used /usr/java/jdk1.6.0_21). Any help would be greatly appreciated
Lou

Hi Lou,
Have you set an environment var for the JAVA_HOME?
you can set it system wide, create or edit /etc/profile.local, and add:
export JAVA_HOME=/usr/java/jdk1.6.0_21
Then reboot the system so the env var gets set globally.
If the site is still not accessible, rerun the Teaming install choosing to reconfigure, double check the JAVA_HOME path set and see if that does the trick.
Cheers,
Willem

TS2529 itunes will not access the istore or itunes server for updates

I can not access the istore or itunes server from my itunes page...any articles or links on this???

Hi, tsgeisel,
iTunes can access CDDB for track information after a CD has been imported into iTunes by using the Advanced menu option I mentioned in my previous post.
If you want to check it out, import a CD when you're not connected to the internet - or with Automatically retrieve CD track names from internet unchecked in your iTunes Importing Preferences.
After the CD has been imported there will be no track information included. But if you then select the tracks - all together, one at a time or in any combination you desire - and select Get CD Track Names, you will be pleasantly surprised.

Error: "Cannot access the web server" with BlazeDS Turnkey

Help! I'm new to Flex and BlazeDS and Eclipse. I was trying to setup a Flex Project using a BlazeDS/Tomcat server running from Eclipse on Windows XP per the example in flexbandit.com/archives/55#comment-269 and in (www.infoq.com/articles/blazeds-intro).   I am NOT using the Eclipse Flex plug-in. I'm using Flex Builder for the Flex code.
Here's what I've done:
I installed BlazeDS and tested http://localhost:8400 - That worked.
I setup Tomcat in Eclipse. - That seemed to work.
I created a Dynamic Web Project in Eclipse - That seemed to work.
I created the bare-bones BlazeDS Configuration under the Eclipse project and then created a basic HelloWorld java class.
I added the destination in the “remoting-config.xml” file found in the c:/projects/workspace/ReportGenTool/WebContent/WEB-INF/flex” directory:
<destination id="HelloWorld">   <properties> <source>HelloWorld</source> </properties> </destination>
When I started the application server by clicking on the server's green play button in Eclipse and then tried to open localhost:8400/ReportGenTool, I got the 404 error : The requested source (/ReportGenTool/) is not available which according to the instructions is fine.
Next I created a Flex Project, but when I try to validate the new Flex project configuration, it gives me an error "Cannot access the web server. The server may not be running, or the web root folder or root URL may be invalid."
When I validated the server was running after setting up the BlazeDs Turnkey, I saw the BlazeDS page.
Now when I bring up http://localhost:8400 I get:
      Directory Listing for /
      Apache Tomcat/6.0.14
My eclipse project is named ReportGenTool and I've overwritten the WebContent directory with the META-INF and WEB-INF directories from the BlazeDS installation (C:\blazeds\tomcat\webapps\blazeds). According to Eclipse the server is running.
My Flex project is named ReportGenTool and is located in another directory away from the Eclipse project directory.
     My root folder is: C:\Projects\workspace\ReportGenTool\WebContent
     Root URL: is http://localhost:8400/ReportGenTool/
     Context root is: /ReportGenTool/
Any idea what might be wrong? What didn't I configure that needs to be configured?
Thanks in advance.

This is not working because your router has a direct to your web server that is not through the outside interface which is needed for nat to occur, for this to work you need to setup a loopback interface as nat outside and policy route traffic to there for your server traffic
Bu if your server is internal why do you need nat at all? Can you not use bind with views that might be simpler
M
Sent from Cisco Technical Support iPad App

Is there a way to access the web-based setup for my router if I cannot access the internet?

Okay, I need to change the ip address settings on my router. I have a WRT54G Wireless router. I cannot access the internet on my computer connected to the router, and do not know how to change the router settings without accessing the web-based setup page. So, back to my question. Is there a way to access this page if I cannot connect to the internet?

On the back of the router is a small reset switch. Using a paper clip or other small item, press the switch in and hold it for a few seconds. This will reset the router to the default IP address of 192.168.1.1. Enter that address in your web browser, and be sure your computer is attached to the router by an Ethernet cable. Don't attempt to do this using the wireless connection.
Once you have reached the web configuration utility you can change the DHCP settings.
To give your PC a static IP address you will need to open your network connections panel and, assuming your using Windows XP, make the changes from dynamic IP to static there.

How can we access the file/directory system in the server

Hi friends,
I have made a text editor attached with an audio player for my project.
Both text editor and audio player are implemented in applet and put in to a
jsp page using jsp:plugin. Text editor and player are separate applets running
in the same page and from same server.A client who is using this editor may
want to save the edited text files to the server as well as hear audio files from
directories in the server.
My question is how can we access the file/directory system in the server
like we do in the local machine.When the user cliks save or openfromserver button
in the editor, folder/files in the server must be displayed as we do with FileChooser.
I am using Apache Tomcat 5,wiindows 2000 server, jdk1.5.
manu

You can't access it directly. But your applet can make net connections to the server, and the server can provide that kind of functionality. Generally this is easiest by making HTTP connections and having the server provide the functionality via the web server. (So in your case, JSPs or servlets on the server would list/deliver/create/modify/delete files, and the applets would invoke those JSPs and servlets.

Can't Access the Server RootDSE

Hi All,
I am working on Windows platform and trying to create a directory instance in Sun Directory Server 6.0 using its commandline utility dsadmin by executing the following command:
dsadm create - h localhost -p 2389 -P 1064 D:\Temp\SUNDS_TEMPthen strat the instance as:
dsadm start D:\Temp\SUNDS_TEMPThe instance gets created successfully but when I try to access the instance using an LDAP browset it gives me error:
Can't Access the Server RootDSE
Error Code: 32
Error Message: No Such Object
I am creating this instance to use as Access Manager configuration store. Is anybody aware of this issue?
Thanks,
Tariq Chauhdary

Thank you very much all. I was able to resolve this issue.
I did not create the Suffix and LDAP browser and that was the reason for LDAP browser to raise RootDSE error.

TS3408 Safari on my new iPad mini isn't working - says server stopped responding but no problem accessing the web with my old iPod touch. What's going on?

Safari isn't working on my iPad mini - "server stopped responding" but I can access the web on my old ipodtouch. What's up??

All other apps were working. We fixed it by reverting to factory settings and starting over. Thank you!

Can't access the web setup utility - server says: level_15_access

Similar Messages

Maybe you are looking for