Can't access Web Site, super slowly and time out!
Hi all,
I am using Server 2012 R2 with Hyper-V, HP DL360 G6 Server
The Master OS have a NIC1 to VLAN1 Switch (Also in the Cisco SG300 Switch)
Plus other NIC2 connect to Cisco SG300 28 Switch (Running in L3 Mode), this Cisco then connect to a SonicWALL NSA 2400.
I build some VLAN31 on SonicWALL NSA 2400, and add this to the Cisco SG300 as Truck Port connect Both...
Other Port on the SG300 are untouch, so mean default running mode is Truck mode, and one of it port connect to the NIC2 to the Server ...
Ok, if Hyper-V VM, not enable VLAN in the Hyper-V Management in 2012 R2, it can take the DHCP from the SonicWALL NSA 2400 no problems, can see other LAN (VLAN1) machine well both direction, and go to Internet too.
But, if I setting the VLAN31 on Hyper Manager to some VM, it can take the DHCP and take the IP from SonicWALL for this VALN31, include DNS, GW etc...
But ... it just can ping internet, for example, ping www.yahoo.com it ok, but open IE, enter www.yahoo.com will super super slowly and time out, if running CentOS 6.5 Linux, enter yum update, it total not work, time out, 0.2kb/s etc. But it can ping to www.yahoo.com
no problems...
And If Windows run routert www.yahoo.com, over 10s to see next hub ...
I am double checked SonicWALL NSA2400 Firewall Policy is allow all VLAN and LAN to WAN, and VLAN TO VLAN too..
What is wrong on the Hyper-V VLAN? Do I am setting wrong of my switch port mode (Access/Trunking)?
I am now out of direction what is go on to troubleshooting this.
Thank you.
Microsoft Windows [Version 6.3.9600]
(c) 2013 Microsoft Corporation. All rights reserved.
C:\Users\Administrator>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : JimmyChan-G6-01
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Ethernet 5:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Intel(R) PRO/1000 PT Dual Port Network Co
nnection #2
Physical Address. . . . . . . . . : 00-1B-78-5A-B2-81
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Ethernet 4:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP NC382T PCIe DP Multifunction Gigabit S
erver Adapter #52
Physical Address. . . . . . . . . : 00-26-55-23-1F-E2
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Ethernet 3:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP NC382i DP Multifunction Gigabit Server
Adapter #49
Physical Address. . . . . . . . . : 00-26-55-1A-26-F8
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::1de6:509d:b011:775a%14(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.218.157(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.218.1
DHCPv6 IAID . . . . . . . . . . . : 436217429
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-D3-8A-8D-00-26-55-23-1F-E0
DNS Servers . . . . . . . . . . . : 8.8.8.8
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Ethernet 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Intel(R) PRO/1000 PT Dual Port Network Co
nnection
Physical Address. . . . . . . . . : 00-1B-78-5A-B2-80
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::acb8:319f:2c75:f829%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.101.11(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 218110840
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-D3-8A-8D-00-26-55-23-1F-E0
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Ethernet:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP NC382T PCIe DP Multifunction Gigabit S
erver Adapter #51
Physical Address. . . . . . . . . : 00-26-55-23-1F-E0
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{A9915F4B-84C6-4168-8E25-909FD2105BD9}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{E893BCF0-EA57-4E6D-8406-1B6ECF27A1C1}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
C:\Users\Administrator>
Above is the Server 2012 R2 Master Host (Mother)
But ... actually still have one Ethernet 6 NIC Card there, it also NC382i, buildin HP DL360 G6 NIC... This card is connect to the Cisco SG300 28 Switch and the Server, and make this card as for Hyper-V Switch (Extenal) ...
I don't why run ipconfig /all not see this card above ..
If you need Screen Capture, let me know ...
THX
Similar Messages
-
How can i access web sites configured for internet explorer?
I try to access web sites thatwork with internet explorer from my mac and cannot load the home page. How can i access these pages?
Not sure if you're using a different browser than Safari. If not try Firefox or Chrome.
-
Safari Mac can't access web site that Windows can
None of my Macs can access the site http://cards.123greetings.com . I get Can't Find Server messages in both Safari and Firefox. (Clearing caches doesn't help)
cards.123greetings.com is part of a large free card site that did a major upgrade in October. It still renders correctly on a PC running Windows XP Home which runs on the same network as the Macs, so it's not an isp problem.
Since both Macs (G4 iBook running 10.3, MacBook running 10.4) have the same Can't Find Server problem with both Safari and Firefox, it appears that some setting in the Macs themselves is causing this.
Any help or insight would really be appreciated - Thanks!A big Thank You to Mulder for letting me know that you can access the site (with Mac Safari I presume) - That's good news.
The bad news: I still can't access the site.
The problem affects two separate computers and four browers. Taking your advice, I repaired permissions and logged in as a new account on both machines. Unfortunately that didn't work.
I next tried accessing the site on the MacBook through Parallels running Windows XP Home. The site came up fine using Internet Explorer.
Then I realized that Parallels operates with a different ip address. So I went back on the Mac using a proxy, and the site came right up.
It now seems that the ip addresses of both computers are being blocked at some level. I want to thank Mulder for replying and virtually ruling out that it might be a Safari issue. I'm now "off topic" and will no longer post in this section. But I'm also over my head... If anyone has advice about how to proceed now, I'd truly appreciate it.
Thanks! -
Firefox automatically updates to the latest version which is now version 32. I get the following error message: "Firefox can't find the server at us.data.toolbar.yahoo.com" Preceded by "Sever Not Found" This happens on any web site I try to access. Reloading version 31 Firefox works fine, but then it will update itself again.
Windows 8.1 is my operating system.The latest Release is Firefox '''31.0''' as the only way you would get updated to the current Beta build which is Firefox 32.0'''b2''' (b2 = Beta 2 as there can be say six to twelve Betas) build is if you were on the Beta channel due to having installed a Beta build and continued using it since. If the Firefox 31.0 you installed is updating to 32.0b2 then the 31.0 you installed was a Beta build (make sure the file name did not have say 31.0'''b'''# as there were nine Betas) and not the Firefox '''31.0''' Release say from mozilla.org or https://www.mozilla.org/en-US/firefox/all/
The typical reason for a new version (on Windows) not being able to connect after a new major version Firefox update or install is usually due to a software Firewall blocking the new .exe yet it may stll have the previous version allowed.
*https://support.mozilla.org/en-US/kb/firefox-cant-load-websites-other-browsers-can
*https://support.mozilla.org/en-US/kb/configure-firewalls-so-firefox-can-access-internet -
I am trying to access a web site that I normally have no problems accessing. Now Safari tells me:
Safari can't find the server
Safari can’t open the page “http://www.xxxx.edu/” because Safari can’t find the server “www.xxxx.edu”.
We are using an apple time capsule and no device on the wireless network can open the above web site. We asked a friend to log on and they had no problem accessing the web site.Hi,
Check Network pane in System Preferences. Select the Proxies tab.
If there are any boxes selected on the left, deselect then quit Safari. (Command + Q)
You can also access that information from System Preferences - Advanced. Click the *Change Settings* button.
Relaunch Safari.
Carolyn -
Query runs slowly and times out in CF 8
I'm trying to run this query using Coldfusion 8 and MySQL 5.
If I run the query directly off the database the results are
returned very quickly.
If I run the query through CF 7, it's pretty slow but still
runs. If I run the query through CF 8 it takes FOREVER, then times
out.
Any ideas what could be going wrong here?
I'm no DB expert. But if the query can run quickly directly
off the DB OK, but then bombs out in CF 8, that the problem might
be with CF 8 itself?
<cfquery name="theOrders"
datasource="#Application.ds#">
SELECT o.orderid, o.dealer, o.dealerRep, o.dealerPO,
o.dealerShippingInstructions, o.dealerFreightCollect,
o.othershipping, o.billoflading, o.carrier, o.othercarrier,
o.serialno, o.ShippingDate, o.Shipping, o.ShippingTotal,
o.SaleSubTotal, o.SaleTotal, o.Tax, o.Discount, o.DiscountRate,
o.Status, o.DateIn, o.bFirstName, o.bLastName, o.bAddress1,
o.bAddress2, o.bCity, o.bState, o.bZip, o.bPhone, o.sFirstName,
o.sLastName, o.sAddress1, o.sAddress2, o.sCity, o.sState, o.sZip,
o.sPhone, o.sPhone2, o.Message, o.dealerShippingInstructions,
o.bCompany, o.sCompany, o.bEmail, o.ipaddress, o.oAuthorization,
o.CCType, o.CCNum, o.CCName, o.CCYear, o.CCMonth, o.entryDate,
i.RelProductID, i.Quantity, i.RelUnitPrice, i.Shipping, i.Discount,
i.title
FROM tblorders as o, tblorderitems as i
WHERE o.OrderID=i.Relorderid
ORDER BY OrderID ASC
</cfquery>The server monitoring tool that is built in CF8 can help
debug this issue quickly. It can give you report about query
execution time, time taken by a tag to execute and lot more other
details.
You can launch sevrer monitoring via CF Administrator. -
Intermittent can not access web sites.
I have a HughsNet satelight dish/ HughsNet modem. I have a
WRT 160N v3 rounter that routes two computers (mine and my wife's) that are
connected to the router with Cat 5 cables. Each computer has a printer attached to
the local computer only (no sharing). We have had several power outages.
We have been having increasing problems with connecting to websites and
connecting to AOL. We have these problems with both AOL and Google Chrome.
The error messages are: "The web address could not be found", and onece I got:
"More than one device is performing address translation (NAT)". Also, some
downloads fail.
What I have already tried: I opened a utility (trouble shooter?) where you type in the
name of the website and it shows the numerical translation...it was working without
error.
These problems occur on both computers and it does not matter if only one is being used and
the other is sleeping/shut off.
I flushed the DNS cache on both PCs:
(Open up a command prompt (Start > Run > cmd.exe > OK).
Type in the command ipconfig /flushdns)
I made sure that my router's firmware was the latetest available.
I changed the router to distribute Goggle's DNS (8.8.8.8, 8.8.4.4.) instead of the default
I.S.P's.
I opened my Local Host file and checked to make sure that there was not any ip
addresses listed that were not commented out (#).
However, when I went to my wife's comptuer to do the same thing, C:\Windows
\System32\dirivers\etc, there was NO host fire or any other file in the etc folder. Do
not know why, I never deleted it and my wife would not know how to delete it.
When I typed the the ip address for the router on my wifes compter (mine was o.k.),
instead of a blank user name and "admin" as the password, both fields were
blank...keeping me from access it. I tried entering admin as the password and
leaving the username blank, but it told me I had not entered the correct password.
I have disabled my Firewall, no change.
I have run Malwarebytes, and have reset (little red button on the back), the router all
to no avail.
What to do? Any help, ideas please.
Note: I am a rank amature. If you give me an abstract of a possible solution (like: set
your router to bridge mode, I will not be able to do it. Please give any possible
solutions in the "just like I am six years old", format: First type in XXXX then select
XXX, then go to XXXXX etc. An abstract answer will only make sense to other
experts (which I am not), and frustrate me.
Thanks for any help.In this example, they show you how to change the local IP address to 192.168.2.1. But use 192.168.4.1 to be safe. Don't worry that it says DSL. It's the same principal.
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3687 -
Can I access Webi queries and Xcelsius dashboards from SAP portal?
Hello,
Can I access Webi queries and Xcelsius dashboards from SAP portal? And how?
ThanksPortal Part 1
/people/ingo.hilgefort/blog/2010/03/29/sap-businessobjects-enterprise-sap-enterprise-portal--part-1-of-4
Portal Part 2
/people/ingo.hilgefort/blog/2010/03/30/sap-businessobjects-enterprise-sap-enterprise-portal-part-2-of-4
Portal Part 3
/people/ingo.hilgefort/blog/2010/04/08/sap-businessobjects-enterprise-sap-enterprise-portal--part-3-of-4
Portal Part 4
/people/ingo.hilgefort/blog/2010/04/21/sap-businessobjects-enterprise-and-sap-enterprise-portal--part-4-of-4
Ingo -
Turned on computer this am and firefox icon not there. Used Internet Explorer to access web sites. Was able to access my Yahoo home page but not able to open my e-mail account. I am not savvy enough to change settings by myself, so I really need help.
Thank youHi--I tried your suggestion and no dice. A window came up with the following:The item 'Firefox.exe' that has this shortcut will no longer work properly. Do you want to delete?
Another window said 'C:Program files (x86) Mozilla Firefox\firefox.exe' specified in the target box is not valid. Make sure the path and file name are correct.
I have no clue as to what that means. I did delete the shortcut.
Finally went into our Kaspersky virus protection and found Firefox is in quarantine and that is probably why I am unable to uninstall and reinstall.
Any ideas????
Thanks, Ginny -
I'm trying to update a Muse site and it keeps telling me that the site was created with a different version of Muse. I have updated Muse and still can't access the site to make changes.
Hi rgarden95,
Can you please confirm the exact version of Muse you are opening the file with?
To check the version of Muse, please click on help->About Adobe Muse CC.
Regards,
Akshay -
Can't Access One Site - Common Threads
I have recently been hit by the unable to access one site problem.
Having read through all the threads, it seems many people are identifying it as a possible DNS issue; however, it seems that almost all of the issues are with people who are hosting their own web servers off-site.
I was hoping this thread could gather information from people who are having/had this issue?
1) Was the inaccessible site self-hosted?
2) Did you have any server changes, etc?
3) Have you solved the issues, how?
Hopefully this gets to the bottom of things.There is one site that I am aware of that I can not access using my Airport. I have narrowed down the issue to the Airport so far. When I bypass the Airport, the web site connects. Both my Macbook and two PC's can not access this site if I connect via the Airport. I have reset, powered down, booted the modem, worked with Norton and Comcast: still no fix.
I tried changing settings in the utility tool that were suggested on the boards here and still no correction. If anyone has an idea, please post here. Thanks. If I find a correction, I will post here. -
I am new to RemoteApp. I have been using WSE 2012 R2 for some time, mainly for the remote web access web site. I would log into my site (<my name>.remotewebaccess.com/Remote). Then, I would see my server listed under "DEVICES".
I would click on the tile for the server, and the Dashboard would open.
I just followed a tutotial to install the role for RemoteApp publishing. It looks like it worked. I now go to my RD Web App site (<my name>.remotewebaccess.com/RDWeb), and I can log in and see my RemoteApp. But now I cannot
figure out how to get to my server's Dashboard, because when I go to my main web acess site (that ends with "/Remote"), the server is not listed under devices.
Ideally, I would like to see all of my computers, including the server, on the main Remote Web Access site. Also, it would be great if I could see my RemoteApps there too. But I don't know if that is possible. Can anyone help me get
to that state, or know if what I want is possible? I want everything on the same web page:
Devices
Shared Folders
Links
RemoteAppsHi,
Based on your description, I understand that DEVICES tab disappears from Remote Web Access website after RemoteApp
configured. If anything I misunderstand, please don’t hesitate to let me know.
à
But now I cannot figure out how to get to my server's Dashboard, because when I go to my main web acess site (that ends with "/Remote"), the server is not listed
under devices.
Did all users encounter the same issue when access RWA? Please open Dashboard and navigate to USERS tab, then
click the problematic user account and select View the account properties. In Properties of this user account, please navigate to Anywhere Access, then please check if Computer option was checked in
Show selected links on Remote Web Access. Meanwhile, please also use an administrator user account to check if this issue still exists.
In addition, please follow the path: C:\ProgramData\Microsoft\Windows Server\Logs\WebApps folder and check
RemoteAccess log file if find more clues.
Hope this helps.
Best regards,
Justin Gu -
An error occurred while publishing file "/Web/Sites/iWeb/Jim and Steph's Si
I'm guessing this is a common message most see when they try to publish their website. Reason I say this, is it is the only message I have recieved in the last week when trying to use this faulty software.
Here it is again if you missed it:
An error occurred while publishing file “/Web/Sites/iWeb/Jim and Steph's Site/Jim's Blog”.
I got this MacBook week ago yesterday. Totally excited to share pictures and blog information. Spent 99 dollars or close to it for a mac account to simply share this information on the web. The first four pages (all pictures), I published worked well. Then I updated to iWeb 1.1.1 and tried to publish with blogs and more pictures and it won't work. Now all that I published before does not even come up. I emailed support here on mac.com and got the generic reply that I have already read on this forum. I tired as many fixes as I could to no avail. Two questions:
1. Any ideas to fix this problem?
2. Can you get your money back?
Sorry this was so long.
Thanks everyone,
Jim BJim...
Try doing a "Publish All to .Mac" if nothing else works for you. And if I could make a recommendation, it probably wouldn't be a bad thing to simplify your site name (Jim and Steph's Site) and eliminate the apostrophes (also in Jim's Blog). A longer site URL with complexities such as punctuation and spaces and even capitalization can potentially wreak havoc on your site navigation and function. Simplifying your site and page names will at the very least lead to shorter and more recognizable URLs...and when you start to add more pages it will also make the navigation menu at the top of your pages look "cleaner". Think simple names, like "oursite" and "HeSays" or "SheSays"
Just a suggestion. -
Just recently I am getting the following error message when trying to access web sites. I am using Firefox browser version 10.0.2. I get a pop up window stating "Exc in ev handl: TypeError: c.location is null" as the web site page is being displayed in browser winder. Then I have to click ok. It doesn't matter what web link/site I go to it happens. It is an issue with some plug-in?
I have advised McAfee's product team of the problem and this thread, and they're looking into it now.
-
"Sorry you can't access the BT Sport App and onlin...
I've been trying to login to the BT Sport app and keep getting told that I haven't activated it yet. I'm shown an activate button and when I press it I'm taken to a site where I have to log in using my My BT credentials. Upon logging in I'm shown the following message:
"Sorry you can't access the BT Sport App and online content because a BT ID created by Stephen is the account holder."
The message is completely nonsensical as I the account holder and I've logged in with valid credentials. I tried calling the helpline and am still waiting for someone to call me back, even though I called them two hours ago. What awful service.Hi W0035521,
Welcome to the community forum. Do you have more than 1 BT ID? It sounds like you have another ID that has been set up with account holder status. I can take a look at this for you. Please send me in your details using the "Contact The Mods" link found in my profile.
Thanks
PaddyB
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)
Maybe you are looking for
-
In XI 3.0 how to set up Alert configuration......
Hi All I am new to XI and Pls..help me on this How to set up Alert Configuration in XI 3.0 (SP 9) What are the settings i need to do in RWB... For particular Purchase order How to set up the alert configuration ? Thanx in advance
-
I am getting a 3014 error message when trying to recover my iTouch after upgrading to 10.7.0.21. Everything worked fine until the upgrade.My PC is current with upgrades, I have unplugged all USB connections and I have disabled my firewall security.
-
Time Machine corrupting external USB hard drives
In February I installed two Mac Minis running 10.8 Server. Each machine had an external hard drive connected to it. Sometime over the Labor Day weekend, both drives stopped working. When I came in Tuesday, each machine had a message on the screen tha
-
I'm having trouble with my roommate and my WRT310N router. I setup the router password, but he downloaded LELA and uses it to change the router password and open ports for his own use. Needless to say, I want to setup my router so that LELA cannot
-
Premier Elements 13 I am in the process of making a movie with Premier Elements 13; it has been functioning fine--until today. For some reason, it no longer plays when I press the play arrow button to preview recent additions to the script. I have r