Can't boot from IDE RAID 0 on K7D

I'm running the K7D with the latest BIOS, with two MP 2000+ processors. In PCI32 slot 1 is my adaptec 1200A IDE RAID controller, with one WD Caviar 1200JB set as the master drive on each of the card's IDE channels.
With the drives set for RAID 1 (mirroring), I have no problems. I can install Windows 2000 Professional, and I used it for weeks with no significant problems.
With the drives set for RAID 0 (striping), Windows 2000 installs just fine, but the K7D will not boot from the array. If I boot from a floppy or a CDROM, The Win2K boot loader has no problems loading win2k from the RAID 0 set. But the K7D does not find an MBR on the array.
Where could the problem lie? My Award BIOS boot order is CDROM, SCSI, HDD0. The array is marked as bootable in the RAID card setup.
Thanks --
Neil

no Paazel...
this is the right forum for him
his board uses the AMD chipset... this is the AMD chipset forum...
i think he has a MSI K7D Master-L 760 MPX
witch is a dual prossesor mobo. with the AMD chipset.

Similar Messages

Can't boot from IDE hard drives

Just purchased a barebones system with a KEN NEO Platinum board running an AMD 64 3400+. Tried to install old Maxtor hard drive (40 gb) into new system and a blue screen pops up for less than one second and reboots PC. I can’t read the blue screen but I believe it is saying there is a hardware conflict.
What is causing this. The CMOS recognizes the HD but it can't boot from it. I’ve got two of these units and both have the same problems. I put the drive back into the original PC and it works fine.
Need help desperately.

When I connect the cables, they show which is the slave and which is the master. In the CMOS, everything looks fine. I've noticed alot of people are having difficulty installing used and new hard drives. I've been working with PC's for quite a while and I've never had this much trouble. I was hoping there was something I missed in the CMOS settings.

Can not boot from a RAID 5 volume

Dear Friends,
I have a Mac Pro (3 GHZ) with RAID that will not boot off of a RAID 5 volume. Here's the details:
The unit has 4 768 GB drives that I have made into one RAID 5 set. After that I broke it down into 2 two volumes one for OS (200 GB) and one for storage (the balance of the RAID). After that I copied a known good image to the OS volume.
The Start-up disk utility on the DVD sees the OS but when I boot it sits for a long time and eventually gives me what Apple calls the prohibited icon; a circle with a line-through it like Ghostbusters.
The patron table is good, and I have done this on another Mac Pro. I have tried to rebuild the RAID a few times with no luck. Ideas would be appreciated. Thanks!

My guess is that the Mac OS X system is damaged. You may need to use the Sysytem CD to perform an archive and install.
For those interested in bootable RAID cards on the Mac Pro, the Areca is the only non-Apple solution that I have found with this capability. You can read more about it here:
http://www.amug.org/amug-web/html/amug/reviews/articles/areca/1221x/
Have fun!

645E MAX2-LRU Can I boot from Raid?!

Hello,
Is it possible to boot from the onboard RAID?
I'm not sure cause I can't boot from any HD that is connected to the RAID IDE when I use them in "non Raid" mode.
I have an entry in the Bios "boot device" where I can set "Legacy SCSI". Is this the entry for the RAID Controller?
THX for your answers and excuse me for my bad english!!
Greets burnmeister

Some more interesting information is had in this article about the virtues of SoftRAID vs. OS X RAID.
I've got backup to my backup. Call me paranoid if you like, but I hate standing there looking like a horse's tail end and crying about lost data and irreplaceable applications because I didn't do some simple housekeeping.
Add me to the "tri-backup" team (the wife hates all my hard drives.... sees money spent, I guess....).
I also keep 'hard copy" DVD of archived data, and all photos and audio. It only takes losing some important data once to underscore the importance of backup. In my case, it was a near miss (was able to scavenge the SCSI drive), but it scared the bejeebers outta' me......

Can I boot from a SATA drive? What if it's RAID?

I'm planning on getting the MSI 875P Neo FIS2R 800FSB motherboard. I'm also planning on getting ONE SATA hard drive. Can I boot from the SATA drive? Do I HAVE to set up it as a RAID drive? Can you boot from RAID drives? RAID and SATA confuse me a little. Anyone care to help?

I'm using the MSI 865PE Neo2 board and I'm having this problem. It probably has an easy solution, but this is my first build, so I'm not sure exactly what to do.
MSI 865PE Neo 2 Mobo
2.4b P4
Seagate SATA 80GB HDD
Panasonic FDD
Lite-On DVDROM
It took me a little bit of experimenting, but I got the BIOS to recogonize the DVD & HDD. It seems every time I got it to recognize one, the other disappeared. Anyway, like I said, BIOS recognizes all 3 now.
I go to install XP and it says I need to install the drivers from a floppy (after I had previously hit F6). Well, where do I get the drivers? I have a CDROM that came with the mobo but I don't know where to find the drivers for the SATA controller on it. ???
Can someone help me by directing me to a download and/or the file names that I need to transfer to floppy for Win XP installation? I would appreciate it. Thanks.

Can I install Snow Leopard and boot from software RAID 1 (mirror)?

I have a Mac Pro (quad core 2.66 GHz) on order for my office workstation. Yeah, I know new ones are probably coming out early next year but due to budget and upcoming projects I need one now. What I'd like to do is replace the pre-installed 640GB drive with two 1 TB drives and mirror them. The 640GB drive will be redeployed to another machine in the office. Can I boot from the Snow Leopard install DVD, go to Disk Utility, setup a RAID 1 with the two drives, install Snow Leopard to the mirror and then boot off the mirror set?
I've searched and found offhand comments to the effect that installing to and booting from a software mirror is OK, but I'd like to know for sure that it's OK. Any experience that you have with such a configuration would be nice to hear.

Yes. But before you do read the following:
RAID Basics
For basic definitions and discussion of what a RAID is and the different types of RAIDs see RAIDs. Additional discussions plus advantages and disadvantages of RAIDs and different RAID arrays see:
RAID Tutorial;
RAID Array and Server: Hardware and Service Comparison>.
Hardware or Software RAID?
RAID Hardware Vs RAID Software - What is your best option?
RAID is a method of combining multiple disk drives into a single entity in order to improve the overall performance and reliability of your system. The different options for combining the disks are referred to as RAID levels. There are several different levels of RAID available depending on the needs of your system. One of the options available to you is whether you should use a Hardware RAID solution or a Software RAID solution.
RAID Hardware is always a disk controller to which you can cable up the disk drives. RAID Software is a set of kernel modules coupled together with management utilities that implement RAID in Software and require no additional hardware.
Pros and cons
Software RAID is more flexible than Hardware RAID. Software RAID is also considerably less expensive. On the other hand, a Software RAID system requires more CPU cycles and power to run well than a comparable Hardware RAID System. Also, because Software RAID operates on a partition by partition basis where a number of individual disk partitions are grouped together as opposed to Hardware RAID systems which generally group together entire disk drives, Software RAID tends be slightly more complicated to run. This is because it has more available configurations and options. An added benefit to the slightly more expensive Hardware RAID solution is that many Hardware RAID systems incorporate features that are specialized for optimizing the performance of your system.
For more detailed information on the differences between Software RAID and Hardware RAID you may want to read: Hardware RAID vs. Software RAID: Which Implementation is Best for my Application?

10.3 Server new install won't boot from Mirrored RAID - HELP!!

Hi all,
I had 10.3 Server running fine on a 450 MHz B&W G3 (home server use, nothing too demanding), when I decided to add a 2nd HD and run the server from a RAID mirror (both 80GB drives). I had problems enabling RAID on the boot drive with diskutil in Terminal, so I decided to rebuild the server. I didn't have much besides the system on it, so backing up data and re-installing isn't a big ordeal (or so I thought).
No problems creating the mirror set once I re-formatted the drives. The install seemed to go fine (10.3.4 on install disk), but upon restart, I got the flashing system folder/question mark. When booting from the install disk, Disk Utility recognizes the RAID, and Startup Disk recognizes the mirror as a viable boot drive and allows me to select it and restart. Same problem, no system found.
When I run diskutil info for the mirror, it lists the mirror volume as Not Bootable.
I've checked the disks with both Disk Utility and DiskWarrior - all looks OK. I've reset PRAM and NVRAM, taken out added PCI cards, and disconnected all FW and USB devices (besides kbd and mouse).
Unfortunately, B&W G3 can't boot from an external FW drive, so I'm stuck with booting from a CD/DVD for troubleshooting.
My next step is to re-install on a single drive again and try to enable RAID and mirror, but I'd sure like to avoid that if I could.
I've searched through this board and didn't really see this particular situation. Any of you smart server folks seen this before -- any ideas or suggestions??
TIA,
Brad
B&W G3 Mac OS X (10.3.4) 450 MHz, 10.3 Server, 80GB RAID mirror

if you backup your data from a NON-RAID Drive (Single drive), create a RAID array and then Restore from the backup you created... you will find you cannot boot from the drive.
Apparently the sector or drive header information in a non-RAID drive is different than in a RAID array... so when you restore the backup data from the non-RAID drive to the new RAID Array; you effectively corrupt the RAID array not allowing it to be booted from.
The solution is to create the RAID array and then re-install your system from scratch... copying over the data you want to keep from your initial backup one file at a time (don't do a complete system copy or you will once again, corrupt your new RAID install).
I had the same problem and it took me a great deal of time to figure it out.
Joe

HP Pavilion 500-210 QE Can't boot from any hard drive.

Good Evening. As you can see from the subject, my computer just can't boot from any hard drive that I put on it. I tried swapping the power supply, the SATA cable, resetting the BIOS, enabling legacy boot, changing from AHCI to IDE and RAID...
When I get to the BIOS setup, I can see the hard drive and its specifications, but it just won't boot or show up when I'm trying to install a new OS. I'm not an expert, but I think the problem might be in the motherboard SATA ports, but I'm not sure. Just to make sure, I did try another hard drive and it didn't work aswell.
I was also thinking about buying an external hard drive and instaling my OS on that, but I don't even know if that's possible and I would really like to have my computer working again.
Thank you for your attention!
This question was solved.
View Solution.

What is the installed operating system?
Did you make a recovery disk set?
Did you happen to make a Windows 8.1 startup disk or USB recovery thumbdrive?
Have you tested the hard disk?
Press the power button and then immediately tap the Esc key. In the Startup menu, choose F2 for Diagnostics. In the HP Basic System Diagnostics menu choose hard disk. Run the test and post the results here.
The issue you are facing has nothing to do with the SATA ports. It is a configuration issue. Your PC is a modern one and its BIOS (UEFI) is far more advanced than what you may have seen before.
If you want to install a different operating system then you will have to make a few changes in the BIOS configuration. Secure Boot is turned on by default for Windows 8 and Windows 8.1. If you try installing a different OS without turning this off then your system won't boot up. You may be running into this if you are trying to install another operating system.
The image below is what will be seen in the BIOS of your PC in the security tab --> . In the secure boot configuration options do not clear the secure boot keys! Those keys are your operating system license activation keys.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Can't boot from cd

Just replaced a hard drive in my old G4 titanium laptop and it worked fine until I did the OS update. The first time i did the update and clicked restart, it would only go to a black screen. I reformatted and thought I would just say to he'll with the update and leave well enough alone. My wife used it for a few days and said it was really slow, so I did the update again. I selected one update at a time and when I did the Security Update 2009-005, it gave an error and said try the install again. I rebooted and now my dock has dissapeared and when I try and reboot, it does nothing. I tried to run disk utilities and the program will not open. I tried to reformat the hard drive, but when I hold the C key down to select the DVD to boot and install from, it goes back to my hard drive and just boots to the installed OS. I then tried to select the DVD from my preference start up disk option and there is no CD/DVD option to select as boot drive. I see the mounted DVD disk on my desk top and can access the files on it, but can't boot from it to reinstall. My install was Tiger full retail. The laptop came with an install disk that had Panther. Any ideas would be appreciated.
Mark

Thanks for your reply and yes I did try option as well, with no luck. I finally reformatted through FireWire and another laptop. I am now installing from the disk that came with the G4. So I will try Panther to Tiger even though my Tiger is a full retail disk. I am not sure why Apples up dates to 10.4.11 crash this g4, but I'll try for the third time and see what happens.

Admin password changed - can't boot from CD

I'm the sole user of my iBook, and the administrator password USED to be the same as my user login password. I have no idea what happened, but now it won't accept the admin password (it still accepts it as my user password), so I can't install new software or updates. I also can't boot from the install CD using the 'C' key - nothing happens, it just boots from the HD. In fact, I can't boot into any different mode by pressing a key at startup. I'm going crazy, I have no idea what happened or how to fix it. It's something that's happened since 5/20/06, because I installed 'dashcode' on that date. I also installed the 5/18 security update.
Does anybody know what might have caused this, or how I fix it? Thanks.

Welcome to Apple Discussions!
Have you tried to boot with the Startup Manager instead?
http://docs.info.apple.com/article.html?artnum=106178
Are you making sure to only boot a CD that came with your machine or newer?
http://docs.info.apple.com/article.html?artnum=25517

Will mavericks boot from a raid array?

Will OS X Mavericks boot from a raid array? I know Lion didn't support booting from a RAID.

Well, since no one seems to want to answer this question I've done a little research and answered it myself. Yes, you can boot from a RAID while running OS X Mavericks. The only setback is that you can't create a recovery partition.
While installing Mavericks on a RAID it will prompt you to OK installing without a recovery partition. In laymen's terms it means you have to keep your own backup. If your RAID fails you will lose the data or whatever is stored on it. Simply keep your own backup and you'll be fine. This is the way most people do it anyway. Yes, it may be considered old wave but it's still the best option. It's an absolute. If you have a backup, you never to have cross your fingers, pray and hope the recovery process actually works!
That being said, you can create some really souped up Macs. I actually installed two 480GB SSDs into a 2.8GHz Macbook Pro and the response is phenominal !!! From power on button to sign in screen is less than 10 seconds on a 5 year old Macbook Pro !!! If you hate seeing the little spinning wheel while shutting down this will cure your distress. Shutting down is instantaneous. I love it !!! RAID and SSDs are the best !!! A newer Quad-Core machine has to be even faster which is hard to imagine.
That's my 2 cents ...

Can't boot from external HD with Leopard on MacBook Pro or PowerBook

I can't boot from an external HD with 10.5.5 Leopard on either my MacBook Pro or my PowerBook G4. I had a PowerBook G4 from which I could boot from either an external FW400 drive or an external FW800 drive. At some point, I stopped being able to boot from any HD, but I'm not sure if it was after upgrading to Leopard or not? Recently I just bought a MacBook Pro 15" and transferred all my files over from the PowerBook to the MacBook Pro during the install. However, even with the new computer, still cannot boot from an external drive. I have Leopard 10.5.5 running on both the external HD and the internal HD.
Is this a common problem? Anybody know how to fix it?
Thanks!

That probably wasn't very clear was it? I have several ext. HD's, some with bootable systems and some just backups. One bootable disk was made with CopyCloner and the other was a clean format and only had an original install of the OS just to use for an emergency boot. They both booted just fine. Then at some point, they stopped being bootable. I have used the Control Panel "Startup" and also used the Option key boot and picked the bootable disk. Neither one boots anymore. It started doing this on the old PowerBook and then also refused to boot on the MacBook Pro. This is not the problem with the HD since it happens with any bootable HD. Something is going on at the system level and it was transfered from the PowerBook to the MacBook.
Thanks,
Bill

Can't log in with valid password, can't boot from disk, can't access disk utility, in single user mode can't reset password as appears locked in caps mode with '?' for forward slash, can anyone help?

Can't log in with valid password, can't boot from disk, can't access disk utility, in single user mode can't reset password as appears locked in caps mode with '?' for forward slash, can anyone help?

Which keyboard layout you were using? German, French ... I suppose your layout is reset to the default: US and you are unable to find the "?" or "/" ...
Please have a look into the keyboard viewer, to see how the layout of your keyboard is actually.
marek

Disk repair failed how can I back up my files when I can't boot from the start up disk

When disk repair fails, and I can't boot from the hard drive how can I get to my files to back them up. I have a seagate 1 TB connected to the USB port.

Perubbit,
which model MacBook Pro do you have, and which version of OS X is installed on it?

Can't Boot From Install Disc 1 ?

Holding down "C" at Start Up isn't working.
Most of the time I can't get Preferences > Start-Up to even "see" my Disc 1.
When I can get it to show up in Start-Up, and Select it, and Lock it ... it Still Won't Start Up from the Install Disc 1 ... and in fact usually ejects the disc.
Sometimes when I re-push in the disc, I get the message that a Blank Disc has been detected, "what do you want to do with it."
But, it shows up in Disc Utility, and when I run Verify Disc, it all looks good?!
The Disc has Mac OS version 10.4.8 on it. I'm running 10.5.7. I'm all up to date with my software.
Yesterday I ran the latest version of Disc Warrior. When I run TechTools 4.0 it seems to get stuck running Files. When I run Repair Permissions from Disc Utilities, it shows a fairly massive amount of issues. Running it over and over again doesn't seem to make any difference.
I WANT to run my Install Disc so I can run Repair Disc from Disc Utility ... because I'm having a number of issues ... and I seem to get the spinning rainbow a lot.
SUGGESTIONS ?! ... thanks ...

Disk Utility that can repair a 10.5.7 permissions is only found on the Leopard installer disc. Tiger can't repair Leopard when it comes to permissions, and may also have difficulty with the directory.
Secondly, if your MacBook Pro was purchased after October 26, 2007, it can't boot from any Tiger disc.
If your MacBook Pro was purchased prior, you can use the disk, but you'll want to follow these directions for hardware diagnostics:
http://docs.info.apple.com/article.html?artnum=303081
Only if your MacBook Pro has Tiger installed, should you use Tiger for the directory or permissions*:
http://www.macmaps.com/directoryfaq.html
Macs can only boot from the operating system that shipped with them, and newer retail operating systems. This means:
1. pre-October 1st, 2007 MacBook Pros can boot off:
- - the discs that shipped with them
- - retail 10.5 discs which look like * that do not say Upgrade, DropIn, or OEM.
2. October 1st through October 25, 2007 can do #1, and also use Upgrade and DropIn discs. Those disks were offered as a limited time mail order Up to date program, some were dropped in the box that came with them.
3. October 26th through November 14, 2007 can boot off the discs that came with them, and retail 10.5.1, 10.5.4, and 10.5.6 discs that do not say Upgrade, DropIn, or OEM, and have a label like the image above.
4. November 15, 2007 through June 29, 2008 can boot off the discs that came with them, and the retail 10.5.4, and 10.5.6 discs that do not say Upgrade, DropIn, or OEM, and have a label like the image above.
5. June 30, 2008 through December 14, 2008 can boot off the discs that came with them, and the retail 10.5.6 discs that do not say Upgrade, DropIn, or OEM, and have a label like the image above.
6. December 15, 2008 and later MacBook Pros can only boot off the discs that came with them.
Presumably when Snow Leopard comes out in September, all of the above will be able to use Snow Leopard because of the specs on http://www.apple.com/macosx/specs.html
- * Links to my pages may give me compensation.
Message was edited by: a brody

Can't boot from IDE RAID 0 on K7D

Similar Messages

Maybe you are looking for