Can't Boot from Second Hard Drive

I put a second SSD hard drive into the bay for a second hard drive but I'm unable to boot from it even after making it the primary drive in the computer settings.
Both hard drive are running Windows 8 if that makes a difference.
Any ideas?

Do you have an Intel version of OS X installed on the external drive and did you partition the external drive using the GUID partition scheme? If not then that's your problem. Also, depending upon which model MBP you have you may require a later version of OS X. According to my information the C2D 17" MBP requires at least 10.4.8 (the build that came on the OS X Installer discs that came with the computer.) 10.4.6 will not boot that model.

Similar Messages

HP Pavilion 500-210 QE Can't boot from any hard drive.

Good Evening. As you can see from the subject, my computer just can't boot from any hard drive that I put on it. I tried swapping the power supply, the SATA cable, resetting the BIOS, enabling legacy boot, changing from AHCI to IDE and RAID...
When I get to the BIOS setup, I can see the hard drive and its specifications, but it just won't boot or show up when I'm trying to install a new OS. I'm not an expert, but I think the problem might be in the motherboard SATA ports, but I'm not sure. Just to make sure, I did try another hard drive and it didn't work aswell.
I was also thinking about buying an external hard drive and instaling my OS on that, but I don't even know if that's possible and I would really like to have my computer working again.
Thank you for your attention!
This question was solved.
View Solution.

What is the installed operating system?
Did you make a recovery disk set?
Did you happen to make a Windows 8.1 startup disk or USB recovery thumbdrive?
Have you tested the hard disk?
Press the power button and then immediately tap the Esc key. In the Startup menu, choose F2 for Diagnostics. In the HP Basic System Diagnostics menu choose hard disk. Run the test and post the results here.
The issue you are facing has nothing to do with the SATA ports. It is a configuration issue. Your PC is a modern one and its BIOS (UEFI) is far more advanced than what you may have seen before.
If you want to install a different operating system then you will have to make a few changes in the BIOS configuration. Secure Boot is turned on by default for Windows 8 and Windows 8.1. If you try installing a different OS without turning this off then your system won't boot up. You may be running into this if you are trying to install another operating system.
The image below is what will be seen in the BIOS of your PC in the security tab --> . In the secure boot configuration options do not clear the secure boot keys! Those keys are your operating system license activation keys.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Can't boot from IDE hard drives

Just purchased a barebones system with a KEN NEO Platinum board running an AMD 64 3400+. Tried to install old Maxtor hard drive (40 gb) into new system and a blue screen pops up for less than one second and reboots PC. I can’t read the blue screen but I believe it is saying there is a hardware conflict.
What is causing this. The CMOS recognizes the HD but it can't boot from it. I’ve got two of these units and both have the same problems. I put the drive back into the original PC and it works fine.
Need help desperately.

When I connect the cables, they show which is the slave and which is the master. In the CMOS, everything looks fine. I've noticed alot of people are having difficulty installing used and new hard drives. I've been working with PC's for quite a while and I've never had this much trouble. I was hoping there was something I missed in the CMOS settings.

X86 install was successful, but now I can't boot from the hard drive

I have successfully installed Solaris 10 for x86 from the bootable CD ROMs. However, now, after removing the CD-ROM from the drive and booting from the hard disk I am having problems.
The system attempts to boot. It displays the Solaris Primary Boot Subsytem v2.0 screen...pauses for 15 seconds...then reboots itself. And it continues this process.
However, if I boot to CD-ROM first, then boot to the Hard Drive, I have no problems. The CDE comes up fine.
We are running a 64 bit OS with a SATA drive that is supported. And as I mentioned, the install successfully completed.
Any thoughts are greatly appreciated.

is your hard drive connected as IDE0 - primary master? if not try doing so.

Booting from second hard drive

I have a T510 (4349-2PU) on which I would like to install a second hard drive using the ultrabay adapter. The primary purpose of this would be to run an alternative OS. I wonder if someone could please confirm whether or not this is likely to work, and if I would need to make any changes to the Bios settings? Also, would it matter which drive has the boot manager installed?
Thanks for any advice.

they would both need boot manager installed you would need to set the one you want to boot to first in the BIOs if you want the ultrabay HDD to boot it has to be listed first in the boot order
correction: from andyp Install the OS on the "second" drive with it in the primary slot - swap it to the bay, insert the original drive as primary and use the F12 function at boot. No need for a boot manager - easy peasy.
Thinkpad R61 7733-1GU
Thinkpad X61T 7762-54U
Thinkpad X60T 6363-4GU
Did a member help you today? Thank them with a Kudo!
If a post answers your question, please mark it as an "Accepted Solution"!
Regards,
GMAC

Can't boot from external hard drive

I have a 250 GB OWC Mercury Elite-AL Pro Firewire drive that I use for backups for my MacBook Pro (running 10.4.8) and iBook G4 (running 10.3.9). The drive is partitioned into four parts, two of which I use for bootable clones of the MBP and iBook. I've been able to boot from the MBP clone, but whenever I try to boot from the iBook clone, after a few seconds of the gray screen with the Apple logo on it and the spinning circle, the Apple logo turns into a gray circle with a diagonal line through it, and the spinning thing keeps spinning, and it never boots up. (For lack of a better description, the circle with the line through it is a gray version of the symbol you see, for instance, in the Ghostbusters logo.)
Here's a few things that aren't (or don't seem to be) the problem:
- I'm not trying to boot from the wrong machine--i.e., I'm not trying to boot the iBook clone from the MBP
- Since I've tried creating the clone with both EMC Retrospect Express and SuperDuper and get the same result with both, it doesn't seem to be the backup software
- I've tried completely erasing the partition (including erasing the free space) from both the MBP and the iBook before creating the clone
- Just for good voodoo, I've also repaired permissions, reset the NVRAM, and run a disk repair on both the internal iBook disk and the clone
- The iBook definitely recognizes it as a bootable drive, since it shows up when I hold down the option key during boot, and also in the Startup Disk section of System Preferences
I'm a little stymied at this point. The only other things I can think of would be that (a) I need to completely reformat and repartition the drive (which I don't really want to do, since I also have other backups and data on there), or (b) for some reason the fact that I initially created the partitions on the MBP is preventing the iBook from using those partitions (i.e., I can only create Intel-only or PPC-only partitions, which I hope isn't the problem, since that would mean I'd need a whole separate drive just to back up the iBook).
Anyone have any idea what's going on?

The MBP and iBook require different partition schemes to be bootable. You won't be able to boot both computers from the same drive.
I can't install Mac OS X on a hard drive
If the installer won't let you install Mac OS X on a hard drive and gives as the reason "Mac OS X cannot start up from this volume," the drive may not have the partition scheme that the Installer requires. The needed partition scheme depends on the type of processor in your Mac. The installer installs Mac OS X for Intel-based Macintosh computers only on drives with the GUID partition scheme. It installs Mac OS X for PowerPC-based Macintosh computers only on drives with the Apple partition scheme.
To check the external drive's partition scheme, open Disk Utility, select the drive in the list, choose File > Get Info, and look for the "Partition Type." If you can't see the "Partition Type," you may have selected the volume instead of the disk. (Drives are flush left, with their volumes indented to the right below them.)
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh2315.html
John

How to boot from second hard drive in Ultra Bay

Hi all!
I recently installed a SSD drive as my primary disk and mounted my old hard drive in the Ultrabay. It still has all its original partitions, which are:
Windows "System Drive"
Windows OS
Ubuntu
Windows Programs
General Data
I can access 1., 2., and 5. from within my new Win7 install on the SSD.
My SSD drive is fully encrypted with TrueCrypt.
Is there any way I can boot from the HDD in the Ultrabay? I still want to access some of the old data on the system drive.
Ideally, there would also be a way to keep the Ubuntu partition and boot it when required. Any chance of making that happen?
TIA
Matt

Hit F12 to pull up the boot menu when you turn the machine on. Select the drive in the Ultrabay. Beware that the drive you boot off of will become the C: drive until you boot off the other drive again. One thing you should do if you haven't already done it is put the stock drive back in the main drive bay, boot into Windows, and burn a recovery disc set. You may need this in the future and it is a good thing to have should you decide to sell the system later since you sill be able to restore it to factory condidtion.
If you just need to access the other partiton all you need to do is right click Computer in Windows Explorer, select Manage, click Disk Management, and assign the partition a drive letter. I would recommend just burning the recovery disc set and wiping out the stock drive so that you can use it for storage.

Boot from second hard drive with ZFS in Solaris 10 x86

Hi,
The usual menu.lst to boot Solaris10 x86 with a boot environment that contains a ZFS boot loader is this one
title Solaris 10 5/08 s10x_nbu6wos_nightly X86
findroot (pool_rpool,0,a)
kernel$ /platform/i86pc/multiboot -B $ZFS-BOOTFS
module /platform/i86pc/boot_archive
title Solaris failsafe
findroot (pool_rpool,0,a)
kernel /boot/multiboot kernel/unix -s    -B console=ttyb
module /boot/x86.miniroot-safeI understand that to add an alternate boot disk, I have to play with installgrub and then attach it in the pool.
But my question is : Is there a way to boot from my alternate hard disk by adding a new entry in menu.lst or is the only
way is to modify the BIOS parameter?
Thanks for your help,
Groucho_fr

Groucho_fr wrote:
Thanks for your answer Alan,
But ok, I imagineI can add a grub entry. But what I want to know is what is the exact way to boot from an alternate hard disk on Solaris 10u6
x86.AFAIK there are only two ways to do this. Select the disks via BIOS which becomes a royal PITA in a short amount of time or play with a boot manager such as GRUB until you get the syntax right.
Personally I put all OS's on the primary disks if possible to avoid these situations and if I have others to play with then you can easily mount them in or set them up as D: drive etc...
The only exception would be in an enterprise setting where you need to do things such as mirroring but then again in those situations it's only one OS per machine anyways so it's much easier.
So at the end, I am not sure what I have to configure and what is the procedure to boot from my alternate boot diskTry the grub homepage for the grub manual and hopefully for a mailing list or try a search engine.
http://docs.sun.com/app/docs/doc/819-5461/zfsboot-1?a=view
has an example to follow of using -B.
And moreover, the installgrub does not working for me :
root@mac1 # zpool status
pool: rpool
state: ONLINE
scrub: resilver completed after 0h2m with 0 errors on Thu Mar 26 10:56:24 2009
config:
NAME          STATE     READ WRITE CKSUM
rpool         ONLINE       0     0     0
mirror      ONLINE       0     0     0
c5t0d0s0 ONLINE       0     0     0
c5t4d0s0 ONLINE       0     0     0
errors: No known data errors
root@mac1 # installgrub /boot/grub/stage1 /boot/grub/stage2 /dev/rdsk/c5t4d0s0
cannot open/stat device /dev/rdsk/c5t4d0s2
You shouldn't need to do an installgrub if you installed Solaris. Try c5t4d0s0 not s2.
alan

W540 - boot from second hard drive?

Morning,
I've recently got an ultrabay adapter and wanted to know if I could run two separate OSs, one from each hard disc.
Effectively, I would like to have one version of windows on the internal HDD for general day to day stuff and one as a programming environment and be able to select which to boot from at start up.
I know I could just use a VM, but some of this stuff (Siemens PCS7) can put quite a strain on the system and I'd rather not have that overhead.
Thanks,
Solved!
Go to Solution.

Hello.
To run a dual OS setup, you have to turn off Secure Boot and set your boot options to both UEFI and Legacy.
I run a dual boot setup Win8.1/Fedora on both my T440's and though it is possible to set it up with UEFI boot
I just skip that hassle and run both OS in legacy mode. If you're planning on dual-booting different Windows
editions, that even applies more.
Further info here: Dual Booting Windows 7 with Windows 8 Pre-Installed UEFI
In BIOS go to Security - Secure Boot - Set to Disabled.
Then go to Startup - Set UEFI/Legacy Boot to Both.
A little further down, set Boot device list F12 Option to Enabled and then you can press F12 during Post
to select which drive to boot from.
Cheers!
ThinkPad W540 (20BG) - i7-4800MQ/24GB // ThinkPad T440s (20AQ) - i7-4600U/12GB
ThinkPad T440p (20AW) - i7-4800MQ/16GB // ThinkPad Helix (3698-6EU) - i5-3337U/4GB
ThinkPad W520 (4282-W4Q) - i7-2720QM/32GB // ThinkPad T400 (2767-W1C) - P9500/8GB
ThinkPad T61 (7665-CTO) - T7700/4GB // ThinkPad T60p (8741-C2G) - T7400/4GB

Can't boot from external hard drive with Snow Leopard

I bought a new Macbook Air with Lion. I have my old Snow Leopard installation cloned onto an external hard drive, and I want to boot from it. I can choose my external hard drive during boot, it shows the Apple logo, but after that the screen goes black and nothing happens. Is there a way to fix this?

Can't be done. Snow Leopard does not contain necessary drivers and perhaps other items required for OS X on the 2011 MBA. In fact, the version of Lion on the App store won't install on the 2011 MBA.
This is totally normal in Apple's world. A new version of MAC hardware that comes with a new version of OS X installed usually will not operate correctly with previous versions of OS X.

Can't boot from internal hard drive.

I just replaced my internal hard drive and copied the back-up from the old drive onto the new one. The new drive appears to be properly formatted and to contain all the data I copied to it, but I am unable to boot from it. Any advice? Thanks!

Thanks, Courcoul. I went back and formatted the drive again, this time booting from the OSX installation CD. (Last time I booted from the back-up drive from which I was copying.) I don't know if it was booting from the CD and not the drive, or that I didn't format it properly the first time, but this did the trick. Working perfectly.

Set Bios to Boot from 2nd Hard Drive

Hello HP forum!
I have a situation that I am afraid may be hardware related, so this is my last attempt for help before I let it go.
In this laptop, I have two hard drive slots with two hard drives. The second hard drive was used as an HP backup/restore drive as shipped from the factory.
I would like to format and install an OS onto the 2nd drive for easy-peesy dual booting. (This is a work computer, so easy + time-efficient + low-risk is optimal). I have actually done this already, but the BIOS does not seem to detect two bootable hard drives. In the BIOS (pretty sure not EFI) boot list, it simply shows the option to boot from "Notebook Hard Drive", which boots from the 1st drive.
In my 1st Drive's Windows 7, I can read the contents of the 2nd disk, so it is definitely functional. Also, replacing the 1st drive with the 2nd drive, I can successfully boot from it, so it is bootable. This seems to imply that my hardware understands that there are two drives, but the BIOS does not recognize that port to be a bootable option, but only a storage option... I guess?
My question is, then, how can I set up my computer to give me the option to boot from either drive? Is it even possible on this hardware?
Thanks
Rex

Did you make sure to update your bios as that could be something that might require a bios update? Also if you can't see or locate that second drive in the BIOS you might not have the option to boot from the second drive? Does the bios also give you the option to boot from the cd drive? Your asking us to see a boot bios screen and unless some has your same make/model no everyone will be able to confirm or see what your asking so unless you can do more looking at all your bios options you might not have the option to boot from the second drive port.
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

Can you install a second hard drive on a Touchsmart320-1130 PC?

This question was solved.
View Solution.

Here are the specs for your HP TouchSmart 320-1130a Desktop Computer. No, you can't install a second hard drive in this computer. The HP TouchSmart and All-in-One computers have more in common with laptops than they do with desktops.
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Can i add a second hard drive to my macbook pro

can i add a second hard drive to my macbook pro

stevefromapo wrote:
I purchased a OWC DataDoubler kit with a 750GB hd and it works fine. I just need to get a USB CD Drive for mac so if i need to reinstall my OS I can do it.
You could put your install disc on a USB Flash drive with Disk Utility. Also, here is the USB optical drive enclosure I bought. He raised the price a few bucks. Mine ran $10.00 with the shipping.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 

Why won't my iMac 27" boot from external hard drive?

I have a new 27in Intel i5 dual core 3.6GHz iMac. It works wonderfully.
My question is this. I have a Pleides Ice Cube external hard drive with a USB 2.0/Firewire enclosure with a 500GB hard drive. I used diskutility to format the hard drive as a GUID Partition Table. I then used SuperDuper to clone the iMac OS 10.6.7 and Apps over to it.
I can select the external drive in System Preferences/Startup Disk to boot from, but when booting the iMac gets as far as the white screen then just stops loading.
I have tried both the USB connection and the Firewire connection (with a Firewire 800 to 400 cable).
I have run Disk Utility and repaired the disk and the preferences.
I have used Disk Warrior to rebuild the directory as well, but the iMac will not boot from the drive.
It does boot from the original DVD's and its own hard drive.
My old 24" iMac had no trouble booting from this hard drive or any of the others I have collected over the years, so I am reluctant to think it is the external drive. It is something to do with this particular processor Snow Leopard and external drives.

It sounds like something in the SuperDuper clone might not have copied well. To get the full answer on that I would check with Apple or SuperDuper to see if they support each other.
As a quick test, if you restart and immediately press and hold "option" on your keyboard do you see your external HD as an option to boot from? If so, click it and see if the boot runs any differently, but if you don't see it at all that could show that the problem is more deep rooted.
Personally, if looking in to either of those didn't give me any other info to go on, I would reformat and start the clone again. BTW, do you know for sure GUID Partition is the format you'd want to do this on? Generally macs use "Mac OS Extended" and some external HDs can use "FAT32" (if you want them to work well with Windows)
Hope that gives a little direction
Alex

Can't Boot from Second Hard Drive

Similar Messages

Maybe you are looking for