Can't boot up on diskwarrior any more

I tried to run diskwarrior yesterday. All I got was a serie of kurnel panics. I was trying to do my biweekly tune-up. I could boot up on my Apple hardware test disk. It showed no problems. The Diskwarrior CD was clean, no scratchs or finger prints. If you click on the Diskwarrior icon it opens a normal window. I had repaired permissions and cleaned caches, etc the day before. I have never reinstalled the OS. I am up to 10.7 and would hate to put in all of those updates. The system other wise seems pretty normal. Anyone have any thoughts??
Bob

I finally did a install and archive. I then updated to 10.4.7.Still have the same problem with 2 different copies of Diskwarior. The 10.4 install disk boots as wll as Tech Tool Pro. I don't think Diskwarrior likes 10.4.7. If you go to startup disks in system prefs, it shows the Diskwarrior CD as bootable.
Bob

Similar Messages

Zen Vision M Firmware Problem!!! Can't deal with this thing any more...

Can't deal with this thing any more...3 Hello friends I'm new in the forum
Well as the title mentions, I'm about to throw this thing oute of the window!!!
It's a 30 GB Zen Vision M, I own it ,5 years now...
I have read all the relevant posts in the forum about this player, I tried my best, nothing really worked.....
So now I have a Zen which only boots in the recovery mode!!
I have Cleaned it Up, Formated it, and tried to reload its firmware BUT when I connect it and try to reload it, in the end it always says Firmware Upgrade Failed!!Really can't understand it!!!!!
I've communicated with Creative, i wasn't at all satisfied with their responses... I think what they're trying to do is to avoid me, and earn some time with really useless suggestions which I had already told them won't work!!!So in the end they wanted me to send my Zen in Italy and pay more than 100 Euros for what an ,5 year old mp3 player?No I prefer buying a new Cowon with that amount of money!!!
Anyways I'm pretty mad now, so I'll move to the subject..
I have Service Pack 3 Windows XP in my computer, and I did roll back on the Media Player 0 from the I had, using the instructions from a previous post. The truth is that it rolled back with less steps than it showed, and I say that because it mentions in a step that in the add-remove programms, in the Windows XP-Software Updates section, I should find a Windows Media player thing which really doesnt exist and I suspect it's the Service Pack 3 because I have done the same in a SP2 and worked exactly as the steps said..Anyway the fact is I have Windows Media Player 0 now!!!
Please someone tell why can't I upgrade my firmware... I can't deal with this anymore!!!!

KRe: Zen Vision M Firmware Problem!!! Can't deal with this thing any more..._
menios wrote:
So you say that I actually have the Windows Media Player 0, because my Zen is being recognised..
I have rebooted it several times but its just the same thing...it shows firmware problem!!
Why isn't this player working?I've seen many people, not only from here, who have the same exact problem and they gave up on their mp3... I dont have this kind of luxury to buy a new one!!I don't know whether Creative has put on this a "time bomb" or is just faulty, but I really wish it could be saved..
I'm saying it is WMP0 because the firmware file sees the player. The computer can recognize it but with WMP components that firmware file would be grayed-out..So when you reloaded the firmware did you choose "reload firmware" Before you connected it's?(That is what erases the firmware prior to uploading the firmware. If you did not do that it could cause it to fail.Do these ste
ps.
Open the firmware file,On the player format>cleanup>choose reload firmware, then connect & run the firmware file.

After Replace queue.llb and notifier.llb for LabVIEW 6.1, I can't use find examples.vi any more.

After Replace queue.llb and notifier.llb for LabVIEW 6.1, I can't use find examples.vi any more.Error list shows that SubVI 'EF-remove queue element with exit or error stop vi': subVI is not executable.
Attachments:
snap158.gif ‏13 KB

I believe that by your action, you removed the compatability VIs and it would appear that the Find Examples used the older queue functions that require the compatability VIs. I would suggest you revert back to the LLBs that were distributed with 6.1. The new queue functions are there for you to use in new development and older VIs won't be broken. You could also make a request to NI support to see about an updated Find Example that uses just the new VIs.

I downloaded a game that need to pay, but after that when i want to update or download a free game from app. It opens the pilling page again, and can't download or update anything any more, why this happen?

Help
I downloaded a game that need to pay, but after that when i want to update or download a free game from app. It opens the pilling page again, and can't download or update anything any more, why this happen?

Recent crashes of certain multimedia contents (this includes Youtube videos, certain flash games and other applications) in conjunction with Firefox are most probably caused by a recent Flash 11.3 update and/or a malfunctioning Real Player browser plugin.
In order to remedy the problem, please perform the steps mentioned in these Knowledge Base articles:
[[Flash Plugin - Keep it up to date and troubleshoot problems]]
[[Flash 11.3 crashes]]
[[Flash 11.3 doesn't load video in Firefox]]
Other, more technical information about these issues can be found under these Links:
http://forums.adobe.com/thread/1018071?tstart=0
http://blogs.adobe.com/asset/2012/06/inside-flash-player-protected-mode-for-firefox.html
Please tell us if this helped!

Why i can't use my visa card any more?

why i can't use my visa card any more?

That's a question only you and your bank can answer.

Why can't I send multiple texts any more? I am on iphone 5 and it is only allowing me to send messages to 10 people at once! Previously on iphones 3 and 4s I could send to many more.

Why can't I send multiple texts any more? I am on iphone 5 and it is only allowing me to send messages to 10 people at once! Previously on iphones 3 and 4s I could send to many more. I use my phone for work and want to send to multiple staff groups or project leaders the same information at the same time and not all of them have email capable phones so text has always been the best solution.
Please help ?

22ms is a long time for your computer, but I am wondering about your network. Are you 10 base or 100 base? Switch or hub? Have you tried a direct connection with a crossover cable? Just trying to spark ideas here. I use TCP all the time but only at 500 ms intervals.

I can't open a .pdf file any more

i made the mistake of subscribing to adobe acrobat. i couldn't use so many features that i dropped my subscription. upon expiry, all it does it prompt me to renew when i click on a .pdf file. they used to have no problem opening with the free reader. no ideas whatsoever from over an hour of the acrobat's chat side, they sent me to this forum...hjelp?
Hi, we are currently helping other customers in line ahead of you. We'll be with you as soon as possible.
While you wait, you can try our community forums where experts are online 24/7.
You are now chatting with 'Rachana'
Rachana: Hello! Welcome to Adobe Customer Service.
wfb: how are you rachana?
Rachana: Hi Wfb.
Rachana: I am good, thank you.
wfb: short for w____ f____ b____, hooo boy! did my parents have fun naming me!!!
wfb: how can i get .pdf's to open now that i am not a paying customer?
wfb: are you there?
Rachana: I understand that you are unable to open pdf files.
wfb: correct. my subscription period ended and i am kaput
Rachana: May I know if you are referring to trial version?
wfb: no idea. i know i paid for it, they charged me monthly and it was some kind of professional account. can you look me up with my email address?
Rachana: Please allow me a moment.
wfb: is that long enough?
Rachana: Thank you.
Rachana: May I know if you are referring to Acrobat Pro Subscription Edition (one-year) subscription?
wfb: possible. i think it was acrobat pro. i am searching my email messages from you
wfb: looks like it:
wfb: Dear w bloxom, Your monthly payment for your subscription to Acrobat Pro Subscription Edition (one-year) has been received. Thank you for subscribing to Acrobat Pro Subscription Edition (one-year). The Acrobat Pro Subscription Edition (one-year) Team
wfb: AD008932429 August 9, 2013 Qty Product 1 Acrobat XI Pro Subscription Edition (one-year) (Mac/Win,Multiple Languages) US $21.89
wfb: i just want to be able to open .pdf's and do not use the other features
wfb: please
wfb: help, please.
Rachana: Please allow me a moment.
wfb: k?
wfb: help, please. i am supposed to be in a meeting
Rachana: I checked and see that the subscription has been cancelled, I suggest you to update credit card details so that you will be able to use the subscription without any issues.
wfb: but i don't want the subscription, i just want to be able to open .pdf's
wfb: help!
Rachana: In this case I will provide you the link to download the trial version so that you can use it.
wfb: thank you. how long will that fix last?
Rachana: Please click here.
wfb: i don't want to bother you again and i would like to just revert to the way adobe acrobat worked for me
Rachana: You can work as the same.
Rachana: Is there anything else I can help you with?
wfb: i don't know if it works yet
wfb: trying to download and install no
Rachana: Sure.
wfb: it's trying to make me reset my password. should i create another adobe ID?
Rachana: Please allow me 1-2 minutes while I send you password reset link.
wfb: i've just reset it, please don't send again!
Rachana: I have already sent the password reset link.
wfb: what does this diagnostic mean?
wfb: Adobe The link you followed expired. Please restart the password reset flow. Adobe © 2013 Adobe Systems Incorporated. All Rights Reserved.
wfb: when i click on a .pdf, it asks me to renew again
wfb: what can we do this time?
Rachana: Have you ever used trial version of Acrobat Pro 11?
wfb: i have no idea
wfb: how can i get this fixed? i've missed my meeting and my lunch
wfb: help?
Rachana: In this case I have 2 options, either you can renew the subscription or purchase full version retail product.
wfb: but...i don't use the product and simply want to open .pdf's. maybe you can explain what has changed at adobe?
wfb: has there been some change in policy that requires purchase in order to simply open, read and print .pdf's?
wfb: i don't know what to do
Rachana: You subscribed to a subscription, which needs to be renewed in order to use it, when the renewal stops, the product cannot be used any more.
Rachana: If you purchased retail version software, you could have opened the files, however as it's a subscription, it needs to be activated [ to activate the subscription you need to update the credit card details ].
Rachana: Unless the subscription is not renewed, no files will open from the acrobat pro software.
wfb: how do .pdf's open without it? as they once did before i purchased any subscription service?
Rachana: To open pdf files, adobe reader is needed, which is a free product from Adobe.
Rachana: However to make any changes or edit the files, you need to have adobe paid product.
wfb: i do not want to make any changes or edit files. how can i revert to my former status?
Rachana: In this case I suggest you to download Adobe reader.
Rachana: Please click here.
Rachana: Are we still connected?
wfb: yes
Rachana: Is there anything else I can help you with?
wfb: so far it has stalled it's installation with an ïnstallation pending" diagnostic
wfb: i would like it if you could remain on the chat for long enough to open a pdf
wfb: it has installed and clicking on a pdf file still just sends me back to the "renew your subscription" diagnostic
Rachana: Request you to ignore the message "renew your subscription"
wfb: o.k.
Rachana: In case if you face any issue with the Adobe free product Adobe Reader, you will have to use adobe forums link to trouble shoot the issue.
Rachana: The link for the adobe forums is
Rachana: http://forums.adobe.com/community/adobe_reader_forums
wfb: there are only two alternatives on the acrobat XI pro renew your subscriptioin prompt, "close"and "try again"
Rachana: I have sent the adobe reader forums link above in the chat, are you able to view it.
wfb: still not having any fun
wfb: trying
Rachana: In this case request you to use the adobe reader's forum link to trouble shoot this issue.
Rachana: Is there anything else I can help you with?
wfb: i still have no feedback, cannot open the file, missed a meeting, missed lunch. although i have been invited to join the adobe reader forum. so i have joined and typed in my question. is that really where we're going to leave this?
Rachana: I am sorry, it is an technical issue.
Rachana: As you have reached the customer service, please visit forums for resolution.

You have Acrobat Pro on your system. It will try to open PDFs, and of course it will fail. You must uninstall it. Then, you will need a PDF reader. So install Adobe Reader. That seems quite simple, but perhaps something is wrong. If anything goes wrong with these two steps (1) uninstall Acrobat Pro (2) install Adobe Reader, then please let us know the details.

Can't print to shared printer any more with Tiger

Hello,
I upgraded to Tiger from Panther on a powerbook 12". My printers (hp 1700cp and hp 920c) are linked to my G5 dual 2ghz by USB, and shared in the sharing panel. I network the two together by ethernet (via a Farallon Netline broadband gateway router/hub).
Since moving to Tiger on the powerbook, when I press the "print" button in the print dialog for any program, notheing happens. Same when I press the "pdf" button in the same dialog.
If I link the printers directly to the powerbook using a USB cable, it prints fine.
I upgraded to Tiger using the archive and upgrade option. I'd like to do a straight re-load of Tiger from the disks, but as I have since upgraded to 10,4,3 via software update I don't have that option any more.
Can anyone help ?
Thanks.

Hi, I'm having a similar problem.
I print to an ancient networked LaserJet at work using LAN. I am not able to do it wirelessly. This arrangement has been working flawlessly. Over the weekend, I did an Archive and (re)Install of Tiger in an attempt to resolve a trackpad issue. Since then, my PowerBook has forgotten all of my printers, which is not a big deal, but the PB only sees the LJ intermittently. For example, Tuesday and Wednesday it worked fine, except each day I had to re-add the printer when I started up in the morning. Thursday, I was unable to see the printer at all, even after fiddling with IP addresses and all that. Today, the printer showed up and I printed a test mail message, but when I went to print an attachment, the LJ was gone.
I have installed all the software updates available through 1/5/06. Why does it come and go? How can I get it to automatically be there? Oy!
Thanks,
Brooke

.mac family pack. Why can't I change these addresses any more?

I bought a family pack years ago and set up email addresses for family members and one for a vacation rental we had. We no longer own the vacation rental and I want to delete that account and set up a new .mac address for what we are now doing? I used to have to pay for the email accounts. Are they now free?

There is no DotMac or MobileMe any more. Each of your Family Pack accounts should have been migrated individually to iCloud, but even if you didn't do that you should be able tro re-enable the addresses (though not access any previous contents) by signing in in System Preferences>iCloud.
You cannot delete Apple IDs or iCloud accounts, but if the account you refer to wasn't migrated it's not active anyway. You cannot re-use the address in another account, and though you can set up new iCloud accounts you cannot create @mac.com addresses, only @icloud.com addresses. There is no Family Pack facility in iCloud.
iCloud is free at basic level with 5GB storage; you can purchase extra storage if you wish.
More information on iCloud here:
http://rfwilmut.net/icloud

I deleted my partition but can't install Windows 8.1 any more.

I've deleted my Windows partition in disk utility, but now every time restart my MacBook Pro (2012, 13 Inch) without holding down the option key and it says your PC needs to be repaired and the wininstall file is missing even though ive deleted my whole partition. When I do hold down the option key I can't go into windows because I've deleted it but I still see the EFI Boot partition. Now I want to install a better Windows version but I can't because when I enter the serial it says it can't verify it.
I have an older backup of my disk from before all this happened, so I've tried to erase my disk but every time I rebooted holding command and R, but every time I tried my mac shut down while loading the Apple sign.
Please help!
Raoul

There are several possibilities.
1. You do not have contiguous free disk space.
2. BCA has failed, or you may have a Fusion drive which is causing problems.
3. You have incorrect permissions on the disk.
4. Can you boot in OS X Safe Mode - OS X: What is Safe Boot, Safe Mode? - Apple Support?

I can't boot from the DiskWarrior CD!

Something went wrong with the OS X filesystem on my PowerBook, and whenever it boots from disk, Mac OS X fails and falls into Single-User Mode. From here, I can run fsck, but it can't repair the drive.
I was told that DiskWarrior could probably fix my problem, so I decided to give it a try.
The problem is that it won't boot on my PowerBook! This is despite the fact that the PowerBook will boot just fine from a Mac OS 9.2.1 CD and that the DiskWarrior CD will boot fine on my iBook G4 running Mac OS X 10.4.3.
I've been trying for hours, and I've done the following steps:
Holding down "c" at boot. - Results with Floppy and Flashing Question mark.
Holding down Command-Option-Shift-Delete at boot. - Results in the same.
Resetting PRAM and doing above actions.
Booted into Open Firmware and typed "boot cdrom"- this gave me a grey OS X boot screen with an action not permitted sign.
Any ideas? I can get my data off of the disk by using "scp" via the single-user mode, but it doesn't do me any good because I can't cleanly reinstall OS X Jaguar because I've misplaced the first install disc!!
What can I do here? What are my options? By the way, the DiskWarrior version is 3.0.3.
Thanks for your help!
Brian

I must plead ignorance since I always use Toast, but
does Disk Utility burn bootable OSX CDs? I am sure
you have the answer but I just don't have the time
right now to check.
It sure does. I've used it multiple times in the past to burn bootable CDs.
One option is to use the freeware 'BootCD' to create
a bootable CD and then you can add whatever utilities
you wish before it is burned. This will have to be
done on a Mac that has Jaguar since the Wallstreet
does not natively support 10.3 or 10.4 and the
BootCD uses the OS on the "host" computer to
construct its boot OS.
ttp://lowendmac.com/misc/05/0126.html
I will check this option out. You're just full of work-arounds aren't you?
I put my own DW CD 3.0.3 in my Wallstreet, made on my
iBook burner since the 3.0.3 Update I downloaded
requires using the original CD (I had either 3.0.1 or
3.0.2) and burning a new one with the 3.0.3 Update.
It will not boot my Wallstreet. So I started up in
9.x, launched my XPostFacto (I am running 10.3.8 on
my Wallstreet) and XPostFacto identified the DW CD as
a "MacOS X 10.3.2 Install CD". I believe this was the
version I was running on the iBook when I burned the
new DW 3.0.3 CD -or- this was the version OSX Alsoft
used on my original 3.0.1 or 3.0.2 CD...I can't
recall. So it makes sense my DW 3.0.3 won't boot my
Wallstreet. I am wondering if the real cause of a
no-boot for you is a too modern OSX on the CD. Before
spending a lot of time on CD-Rs, I would contact
Alsoft and see if the Wallstreet will boot the 3.0.3
CD.
I was worried about this originally. I will certainly contact Alsoft about this and post back.
If you are unsuccessful booting the DW CD and have a
set of Jag CDs, you can either erase the HD and start
fresh or perform an Archive & Install...this
preserves your Home folder but you do need sufficient
HD space for the A&I.
I ordered new Jag CDs today. I might just do this. However, I'd still like to get this DiskWarrior issue straightened out for future use and for fellow users of these discussions.
You can also install 10.3.x or 10.4.x (you need CDs)
using XPostFacto. If curious, read all about it:
http://eshop.macsales.com/OSXCenter/XPostFacto/
I was thinking about this at one point in time. How well does Mac OS X 10.3 run on the Wallstreet? I saw something in the release notes about a video problem. Can you confirm anything?
Thanks for your Wallstreet expertise!
Brian

Can not view cellular data account any more (email address does not match)

On iPad, was originally able to go into Settings > Cellular Data > View Account and view the account info. Now cannot. If try using correct email address and password, get message that account or password are incorrect. If try entering just the email address and clicking "forgot password", get "the email address you entered does not match the email address on file for this device".
But the 3G cellular is still working.
Don't know if related, but this problem began after the reports of the 100,000 iPads/users hack. Leads me to wonder if I got hacked.... or more likely if the system/database that "View Account" normally accesses is offline or being reworked by AT&T.
Any suggestions? Best AT&T contact via Internet? By phone #? By local AT&T store? Via Apple? Use iTunes to reset to factory defaults and start over (risk loss of unlimited plan?)?.
Thanks.

Thanks for the replies, I just had the same problem yesterday and it was a misspelled e-mail address, BUT, it did take me three calls to AT&T and more than two and a half hours. The first person didn't even know what I was talking about and gave me a number for iPad support which turned out to be Apple's, so... no help. The second person told me they were there only to solve iPhone problems until I read her your posts, then she tried and tried until the call was cut off (this is AT&T after all). But the third person finally understood, even though it took her almost an hour to get to their iPad support department (she told me it was busy all the time) not before trying with their "technical department" also. I just can't believe that Apple sells millions of these things and AT&T can't supply a direct phone number for this department, or doesn't even train their personnel.

Can't Connect to one person any more even though we can connect to others

I'm hoping that someone has an idea of what i can do to remedy this situation.
I have been video ichating w/ my wife from work for many months. (she does work for my office from home, so it's ok) She has a MacBook Pro and I have a MacBook. Things worked great until about three or four weeks ago. Now we cannot connect w/ video OR audio at all. I can connect w/ anybody else on my list from work and she can connect w/ anybody else on her list from home. But when we try to connect w/ each other, we get the error -22 bandwidth problem.
How is it possible that it is only our direct connection that does not have enough bandwidth when we can use our same connections to video chat w/ others??
We are both current w/ updates on all of our software.
HELP!
MacBook 2GHz Intel Core Duo Mac OS X (10.4.8) 2 GB Ram

I give up,
There are so many routers, osx, macs and settings that it is difficult to find a repeatable bug.
It just feels like that there are three factors that cause connection problems.
And then different combinations when you look backwards.
So what I have to say is that I cannot pin it down or remotely claim I have firm reason to believe what I say is right but I do see some "combinations of plausible suspects causing the same error message"
The first Macbook Pro was a hard one, refined, improved etc but a non connector.
And it was very hot, uncomfortable hot. I think the designers had been a little to enthusiastic speeding up the processor time.
Now the heat wouldn't be a real problem, the amount of calculations within a very short time might have caused the probook to
be the king of not connecting. There was a certain issue with a card that time so not impossible. Another variable caught the eye.
The graveyard of routers. Understandable, you hide your router and hope you never have to see it again. They do age though, fast.
Updates and firmware did bring some relieve but the Apple chips are something completely different then when tests showed all was good with your good old router. Yet my G4's did respond and my G5 did not. Something totally different caused the error but it gave the same error tekst. it was me who managed to give my computers the exact same identity. Well the error message was: "user does not respond" and I was convinced that it was some kind of bug causing the universal iChat "does not respond" mistery. The port-forwarding was the only fair chance for connecting, and with endless patience and effort Ralph and a lot of others almost personally fixed every possible router combination sold by Apple. The design and coding assignment however was complete the opposite, plug 'n play. Somehow our neighbor was iChatting just by pointing at his router and we did not respond.
In the beginning the specs looked good, it worked fantastic when you managed to avoid to get one or two "show stoppers" in your setup.
A lot of bandwidth, the right sort of router for your specific setup (os version, router software and maybe the right camera and much more)
It is a miracle that some of us got it right the first time. It ran flawlessly if you had the right combination of settings, hardware and software.
And oh boy, what a pain if you got them all wrong. I've been busy at night so to say.
But there is hope, I've seen Macs go online right out of the box (10.4.8) and it looks promising. They all went full motion video chat with no change to settings or any other effort then clicking on your language etc. Splendid. I dare to say that you need to put an effort in it to get it wrong.
The new 802.11n routers that are leaving the shops are fast and steady, 10.4.9 is ready, and in the distance there is a cat waiting that is awesome. I think I already know which airport/router/musicstore/videoshop I'm going to buy.
Just hope Apple doesn't forget to sync the time with MS, it could take a while to debug.
Regards,
JP
Some tips if you can't wait to chat:
1st, it makes no real difference who your ISP is in this case as your issue is not ISP related.
2nd, whether your computer is named or not in the file sharing prefpane should have no bearing on how well your computer hooks back up to the wireless network following sleep.
3rd, PPPoE is not a setting for your wireless network and shouldn't be a setting for any other computers on the wired network behind your router....the router is the only device that might need PPPoE parameters set in order to communicate with the DSL Modem --- and these days, not all DSL Modems are using PPPoE.
D-Link has been in the past very interesting in how they comply with the overall 802.11g/b standards.....some of their default settings can cause issues for the Macintosh WiFi cards because Apple has implemented the standards in a standard way while D-Link chose to implement them such that they caused the least interference for the way that Windows is implemented......which is not quite to standard.
On your router (using the html embedded control pages) you should be able to fine tune the wireless network performance parameters by hooking your computer to the wired LAN port(s) in the back of the router, turning off your Airport card and then checking the Network prefpane to ensure that your computer has an IP address assigned in the range of 192.168.0.xxx ----
Now open your browser and send it to http://192.168.0.1 then log into the control page with the default username - admin - and no password.
This should bring you to the built in control pages Home......check to see if your router has an Advanced tab and if so, select it, then select the Performance button ------ this should be where you can fine tune the wireless network parameters that D-Link has set to their choice for defaults.
The setting that I seem to recall causing the most issues for Macintosh wireless networking in the past was the length of the Preamble ---- I believe that the choice that should work best is the Short Preamble......
The other setting that would best be adjusted is the one that uses any proprietary accelleration techniques to "double" the speed. On a similar vintage DI-624 I had to disable the "Super G" mode in order to keep the wireless network robust for all clients.
I hope this rambling response helps get you back on track.
So in summary, I think your new MacBook CD2 wireless card should be just fine.......your big challenge is in fine tuning the performance parameters that D-Link chose for the DI-524 so that your router can work in a more standard mode and then your new laptop should hook up as advertized.
When you upgraded the firmware, did you make sure that you had the proper version for your revision model? The D-Link support site Firmware Update page lists several different revisions to that model.
mb2.33hrz Mac OS X (10.4.8) (38518353)|

Can not connect to wireless network any more, missing command

I can not connect to any wireless network. I have been having this problem for days. In desperation I installed 10.4 in a seperate HD. I clicked on the airport icon in the upper tool bar, selected my network name and clicked on "open internet connect" and I was connected, what?? I rebooted into 10.5 and tried the same thing again. But the panel that opens when you click on the airport icon has NO "open internet connect" command. A couple of weeks ago I reinstalled my OS. I have run diskwarrior and Techtool pro. Thinking back to the time I first installed 10.5 I don't remember ever seeing that command. Is Leopard compatible with the airport card? How do I get my "open internet connect" command back??

It sounds like a problem between hardware and software. When you select your network, does anything freeze or does nothing happen?
Nothing happens.
Try this, open your Network Preference Pane, turn off airport off and delete the Airport connection by selecting "Airport" in the left pane and click the " - " button. Click on the "+" sign and create a new Airport connection. Hit Apply if it is available. Turn AirPort on and try to select your network and login if you can. The status should show Connected and an IP address should show up after of a couple of seconds.
I get "AirPort has a self-assigned IP address and may not be able to connect to the Internet". On a couple of occasions (over the last couple days) I got you are connected to the internet on IP 172.17.90.251. However when I tried to open a web page I got the banner you are not connected to the internet. Strange, the pref panet said I was the Safari said I was not. Certainly the IP address does not show up in a few seconds. I also have ComCast cable but I need to use the MetroFi-Free wireless so my wife has the bandwidth to do her company work using VPN.

Why can't I edit in Photoshop any more

I reinstalled both LR4.2RC and Photoshop CS5 on a new drive. But now I can't seem to edit in Photoshop from LR. Am I doing something wrong? It worked fine before (except for getting the "Render in Lightroom" thing because of the differnece in process versions). Using Windows 7 Prof. Cntrl E no longer works and Edit in Photoshop is grayed out on the drop down menu. Both work independently just fine. A setting in LR perhaps? Thanks for help.

Hi ,
We really apologize for all the inconvenience which has caused you.
Assuming that you are using Windows machine please follow the steps below:
On Windows, try the following solutions in order:
Solution 1: Uninstall and reinstall Photoshop. Any information that was damaged since Photoshop was installed is re-created.
Solution 2: Re-create the Photoshop.exe application path registry key.
Disclaimer: This procedure involves editing the Windows registry. Adobe doesn't provide support for editing the registry, which contains critical system and application information. Make sure to back up the registry before editing it. For more information about the registry, see the Windows documentation or contact Microsoft.
Exit Photoshop and Lightroom.
Choose Start > Run. If you do not have Run listed, see What happened to the Run command?
Type "regedit" (without quotes) in the Open box, and then click OK to start the Windows Registry Editor.
Navigate to the following registry key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\App Paths\.
Right-click the App Paths folder and choose New > Key.
Type "Photoshop.exe" (without quotes) as the name of the new key, then press Enter.
Right-click the Photoshop.exe folder and choose New > String Value.
Type "Path" (without quotes) as the name of the new value, then press Enter.
In the right pane of the registry, right-click the (Default) value and choose Modify.
In the Value Data field, enter the location of the Photoshop.exe file on your computer. Include Photoshop.exe at the end of the path. For example, if you installed Photoshop CS5 to the default location, enter C:\Program Files\Adobe\Adobe Photoshop
CS5\Photoshop.exe. If you have a different version of Photoshop or have installed to a different directory, change the path as appropriate.
Click OK.
In the right pane of the registry, right-click the Path value and choose Modify.
In the Value Data field, enter the file path for where the Photoshop.exe file is on your computer. (This path is the same as you entered in step 10, except omit Photoshop.exe from the end.) For example, if you installed Adobe Photoshop CS5 to the default location, enter C:\Program Files\Adobe\Adobe Photoshop CS5\. If you have a different version of Photoshop or have installed to a different directory, change the path as appropriate.
Click OK.
In the meanwhile if these steps doesnt resolve your issues you can contact Adobe support by following the link below:
http://helpx.adobe.com/contact/
Thanks
Mandhir

Can't boot up on diskwarrior any more

Similar Messages

Maybe you are looking for