Can't Ciscoworks LMS 4.2.2 back up the configuration of Cisco VPN 3000 concerntrator?

Hi All,
In VPN 3000 concerntrator, I've enabled tftp, telnet, snmp. I've also successfully added the concerntrator into Ciscoworks LMS 4.2.2. All the ports are verified open to Ciscoworks. No question mark shows next to this device in the device management of LMS. However, when I run configuration Achive Job, I always get the following failed message. Can anybody tell me how to to back up the configuration of Cisco VPN 3000 concerntrator in Ciscoworks LMS 4.2.2? Thanks in advance.

Sorry, but apparently not. Please see the supported devices table (here).
That table states, among other things:
The following features are not supported:
Network Topology Layer 2 Services
Fault Management
Configuration Deploy Protocols: HTTPS, TELNET, SSH, SCP, TFTP, RCP
Configuration Fetch Protocols: HTTPS, TELNET, SSH, SCP, TFTP, RCP

Similar Messages

I want to order a second copy of an iPhoto book. Thought created in the smaller format only the larger format is showing. How can I switch an existing iPhoto book back to the smaller format?

I want to order a second copy of an existing iPhoto book. Though created in the smaller format now only the larger format is showing. How can I switch an existing iPhoto book back to the smaller format?

To change a book size duplicate it (select the book in the source pane and press command and D) since text flow and picture placements can change due to the size differences - then click on change themes, select the same theme and the new size
check it carefully
Before ordering your book preview it using this method - http://support.apple.com/kb/HT1040 - and save the resulting PDF for reference - the delivered book will match it.
LN

I recently had the genius bar change my imac hard drive because it crashed. For some reason Time Machine didn't back up some of my important files. Can I get my damaged hard drive back from the genius bar to see if I can access that info?

I recently had the genius bar change my imac hard drive because it crashed. For some reason Time Machine didn't back up some of my important files. Can I get my damaged hard drive back from the genius bar to see if I can access that info?

Unfortunately, that drive is long gone, probably back to the mfr. Drives are not returned when they are exchanged. You can go by and ask them, but the chances are slim to none.

Backing up the configuration of Westell A90-9100EM15-10

Is there a process for backing up the configuration of a Westell A90-9100EM15-10?
I have several ports configured with Webcams, rdp, etc to the internet and do not want to relearn Westell menus every time Verizon asks me to reset to default. I can get a config listing, but I am looking/hoping for something smilar to the Actiontec (which failed after several years) save/reload config command.
Thanks in Advance.

While I don't have FIOS there is something that I heard/read...
#1 It will depend on the firmware of the router.
I am not sure of the details, so don't quote me on this and say what I saying word for word is correct because maybe it is not.
There is a point that in the firmware release(s) where will not let you restore the settngs from previous/former firmare.
For example the backup settings on 4.9 firmware, you will not be able to restore the settings in 5.0 firmware.
#2 If I am wrong that has not happend yet on the Westell, oh ok.
a) The Westell will not let you restore settings from the Actiontec.
b) If it has not happened yet on the Westell, then some day in the future it could happen (There will a point that in the firmware release(s) where will not let you restore the settngs from previous/former firmare).
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

I downloaded the new version of Firefox and it will not open certain of the addresses that I use to run my business. How can I delete this version and go back to the previous version? thank you

I would like to revert back to the previous version of Firefox. Please tell me how to do this

hello and thank you for your suggestion. I have tried it and, when trying to open a program which I previously was able to, still get the following message:
Remote XUL
This page uses an unsupported technology that is no longer available by default in Firefox.
Please contact the website owners to inform them of this problem.
Seems unbelievable that I previously had no problem and now I do. Have you any suggestions to overcome this? Do you think I can go back further in Firefox history to get a version that will make it possible to access this. Many thanks! Lynn

Can I Transfer Music From My iPod Back To The PC?

My PC was recently wiped, and I have lost a music album that was stored on there. However, this album is still on my iPod mini. Is there any way I can transfer it back to my computer from the iPod?
I've only recently got my iPod so am unsure as to whether this is possible or not.
Any help would be appreciated.

It certainly is possible.
If you want to transfer the entire contents of the iPod back to the computer, use these directions:
MacMuse, "Computer Crashed" #4, 11:49pm Feb 7, 2005 CDT

I downloaded current version of itunes today not knowing I would lose the ability to burn the music I purchased to a cd as well as nano. can anyone tell me how to get back to the previous version or help me to be able to burn my music to a cd as well?

today i made the mistake of downloading the update for itunes, 12 26 12, not realizing i would lose the choice to also burn my purchased music to a cd as well as the nano. can anyone tell me how to get back my previous version so I may continue to make my cds that I play in my vehicle. are there steps I can take to be able to transfer the purchased music to another exterior drive where I can then burn it to a cd, besides the nano? as my name indicates I am just getting too old to keep up with all these changes..

https://discussions.apple.com/thread/4572096?start=0&tstart=0
As for moving you itunes library, just copy the entier iTunes storage folder to the exterior drive. user/MyDocuments/Music/iTunes

Why can't I install Yosemite or go back to the way my Mac was before installing?

Hello,
First, I apologize if someone has already asked about this.
My MacBook Pro, got it around 2010, was running on OS X 10.6.8 (or that's at least what it says when I click on "About StartUp Disk").
So here's what happened: thinking that since everyone is getting on to Yosemite, I downloaded the free update off the App Store. When it starts to install, it shows it's going to take 22-23 minutes and then it tells me:
"OX could not be installed on your computer File system verify or repair failed. Quit the installer to restart the computer and try again."
And when I do, the same thing happens. I want to restart with the Startup Disk, it tells me it doesn't have enough information. Now, I can't make go back to the way it or install at all.
Thank You,
Gooner

The bad news is that the most likely reason the installation failed is due to disk corruption that happened to coincide with the upgrade. The installer performs this disk verification prior to installing OS X.
I suggest the following procedure in an effort to "repair" the corruption to the extent that you can boot from or otherwise mount the affected volume sufficiently to extract whatever information can be extracted prior to replacing it. The reason for putting "repair" in quotes is that whatever caused it to become corrupted in the first place is certain to occur again, and falls short of a strict definition of the word "repair".
Boot single user mode (*) then type
fsck_hfs -rf /dev/disk0s2
Substitute your disk device name for disk0s2 in the above. It will most likely be named either that or disk0s1.
To see a list of devices,
ls /dev
There is no harm in attempting the above multiple times, as often as you are willing, until it finishes successfully. If it does, back up your information immediately since you may not get another chance.
(*) "You cannot enter single-user or verbose mode if the computer owner or administrator has enabled Open Firmware Password Protection."

How can I move my Home & Refresh icons back to the left of the toolbar. Dragging does not work.

Since updating to the latest Mozilla version, the Home Page icon has moved to the right of the navigation toolbar and the Refresh icon is attached to the browser search window. I have tried dragging them back to the left with no success. I HATE them in their new locations. Can you either put them back or make it possible for us to move them?

# Right-click on a toolbar and choose Customize to open the customize toolbar dialog
# With the customize toolbar dialog on display you can drag and drop the icons, placing them where you want

I recently bought a neew ipad mini and have sync messages from my iphone. Which worked fine. I just picked it up and I have only to messages and can't figure out how to get back to the screen with the inbox and other folders?

I recently bought a mini IPAD and have sync messages from my iphone. Now I am stuck under group message and can't get back to the main screen that has the inbox and the various folders. Help???

youngkristen wrote:
So, our hope was we could just hook up the external to the mac and have it transfer seamlessly. Is there any hope of that?
Yes there is, scroll down to the bottom of the following Switch 101 article and click on the arrow next to Manually migrating.
Switch 101: Migrate your Windows files or system to your Mac

How can I get Firefox to take me back to the last Bookmark folder I was in like Internet Explorer instead of going back to the beginning each time??

When i find a website using bookmarks in Firefox and then I want to look at another site in that same folder, especially in a subfolder, Firefox takes me back to the beginning of the bookmarks menu. With Internet Explorer, it takes me back to the same folder or subfolder I was in. For example, if I was wanting to search newspapers, especially if they are in subfolders, I want to stay in that same place. Firefox loses that place, unlike Internet Explorer, and takes me back to the beginning each time. Sometimes I have several layers of subfolders and it takes time to find that place again each time.

A possibility is to open the Bookmarks Sidebar.
Click the list icon next to the star on the Navigation Toolbar and click "View Bookmarks Sidebar" (Ctrl+B).

My font size changed in Firefox when trying to read email using yahoo email. I now have to use explorer to read my mail. can you tell me how to return back to the readable size font. thank you

I have been using firefox for years to read my email. recently the size of text became small and hard to read. I would like to get the text size large again, so I don't have to use the other browser. I have a att yahoo email account and subscribe to at&t uverse for internet service.

I tried both of your suggestions and neither one worked. I found the solution by clicking on the "View" button, then "Reset". This put my email back to the original font/text size. Somehow the screen had been Zoomed in, so to change it, follow the instructions above.

Back To My Mac and Cisco VPN client

I've used back to my mac for a while and love it. Recently I've had to start using the Cisco VPN client and every time I use it it says "Because Back to My Mac is turned on, your VPN connection cannot be established with the server. Would you like to turn off Back to My Mac?". Is there any way to run them both without having to keep starting and stopping back to my mac?

I too have this issue.
Every time I have to connect via VPN, I have to disable my Back to My Mac.
Kinda *****.
Any solution?

Can't show the configuration on Cisco 4503-E

I have cisco 4503-E as my core switch. When I want to read or save configuration it show "NVRAM: Unable to read configuration. Try again later."
Somebody said the cause of simultaneous access to NVRAM. I use "show users" to see the access users but there are no other access, only me.
Can it be cause of hardware?
Please kindly provide the solution. Thanks.
Best regards,
Mano

The issue is triggered when you have a large configuration file and immediately after exiting the configuration mode you attempt to save the configuration in NVRAM. The issue is related to an internal timer event whose behavior cannot be modified.
If you give a sufficient time between an exit from configuration mode before saving the configuration the problem will not resurface.
You can also find one known DDTS - CSCtn46265 which explains the issue. Please let me know if you have any questions.
HTH
Regards
Inayath
*Plz rate if this info is helpfull.

Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
Samir

Hi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir

Can't Ciscoworks LMS 4.2.2 back up the configuration of Cisco VPN 3000 concerntrator?

Similar Messages

Maybe you are looking for