Can't configure Airport Express to Extend Airport Extreme Wireless

I have a working Airport Extreme wireless setup running 128-bit WEP. I now have a computer in a remote part of the house that doesn't have wireless, but has a wired Ethernet port. So I was told by a knowledgeable guy at the Apple store that I can have the AExpress pick up the wireless signal, then provide through it's Ethernet port a wired connection for my computer that doesn't have wireless.
First, is this true? If not, I'll return it.
Second, this has been a nightmare, hours and hours, and I'm pretty good with understanding networks. The book included with the AExpress is a joke, it basically just says "and let the software walk you through what you want to do."
The symptom is that I configure the device and update it with all the WEP 128 key info, but the light just stays blinking amber. I've updated the AE firmware.
What are the steps for setting up what I need? I'm using an up-to-date Mini to configure ... should the Mini be connected to the Airport Extreme base via wireless? Via wired? To the Extreme? Wireless?
This is clearly a sophisticated device with lots of promise and such, but the documentation and the number of posts to this board reflect that clearly there may just be too much complexity here for most people to handle.

So I was told by a knowledgeable guy at the Apple store that I can have the AExpress pick up the wireless signal, then provide through it's Ethernet port a wired connection for my computer that doesn't have wireless.
First, is this true? If not, I'll return it.
Yes, this is true. You can extend the network wirelessly using the WDS feature of AirPort Base Stations. In turn, you can connect wireless or wired clients to the Remote Base Stations.
What are the steps for setting up what I need?
This Apple article should help explain the steps of setting up a WDS between two AirPort Base Stations: http://docs.info.apple.com/article.html?artnum=107454

Similar Messages

  • Can't configure Airport Extreme with IP 192.168.0.1 after software update

    Hi there,
    after updating my ax with utility software 5.3.1 and firmware 7.3.1. The software didn't allow the dhcp configuration to stay at IP range from 192.168.0.40 to 192.168.0.200
    The message said that this is not a valid IP.
    The configuration was working before without any problem.
    After several tries I changed to 192.168.1.40 and 192.168.1.200. Now I was able to save the changes. And the airport is working well.
    But I can't go back to 192.168.0
    But I need to use 192.168.0 for a tunnel to connect to my wifes company.
    Configuration:
    Seperate Modem with DSL.
    Connecting over PPPoE
    Activeted WLan
    Connected computers over Lan and Wlan
    Can anybody help?
    Thanx
    Stephan

    by-feet, Welcome to the discussion area!
    AFAIK the AirPort Extreme base station (AEBS) has always forced the 3rd digit to be a 1 (one), as in x.y.1.z.
    Could it be that you previously had the AEBS to operate as a bridge and your "modem" was actually suppling the IP addresses?

  • Can't detect Airport Extreme wireless network

    My Extreme Base Station seems to be configured ok and I can access it with the ethernet LAN connection.  But none of my wireless devices including my Macbook can see the wireless network.   It's been working fine forever and I did the factory reset after things stopped working today.  But I can't get it back.  Is this a Lion upgrade issue?

    A number of users are making use of the "closed" or "hidden" network feature on their wireless routers, so if your Wi-Fi utility "sees" 10 wirelesss networks.....there are probably another 5 or 6 that it cannot "see".
    The utility will also not pick up potential interfering signals from cordless phones in the area, BlueTooth devices, wireless camera/security systems, etc.
    So, while a Wi-Fi utility can perhaps provide a few clues, it cannot provide many answers in most cases.

  • Can i connect a new airport extreme wirelessly to an existing airport extreme to extend range? if so, how?

    My mother has an airport extreme hardwired to a modem for wireless connection in her home.  she is trying to get a wireless connection in her shop, about 250 away and i was wondering if i can use another airport extreme wirelessly to connect to the wired extreme to extend the range

    And, by clear line of sight Bob means nothing between the two but air space. Windows, walls, trees, bushes, etc. all act to attenuate the signal substantially, thus reducing the effective range.
    If you are willing to spend lots of money you can purchase amplifiers that can extend the range. Check this out at QuickerTek.com.

  • How to make Mac OS X Server auto-configure Airport Extreme port-mapping

    Mac OS X Server can automatically configure AirPort Extreme to make services such as iChat, Mail, Web, and VPN accessible: http://www.apple.com/server/macosx/features/networking-vpn.html
    I presume this configuration generally takes place during a fresh installation of the server.
    Is there any way to re-run this process post-installation?

    That page talks about Snow Leopard's Networking abilities, not Leopards.
    Off hand, I don't know whether what you describe is a new feature in Snow Leopard or not, but I've never seen Leopard do it (and, to be honest, wouldn't want to).
    In either case, it's basically just Bonjour telling the router to configure port forwarding. Given that, I'd start by enabling mod_bonjour in Apache:
    #LoadModule bonjour_module libexec/apache2/mod_bonjour.so
    but I don't know how other processes are doing it.

  • I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

    I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

    Extending using a wireless connection always results in a performance compromise.
    If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
    Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
    If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
    Post back to let us know which way to you want to go.

  • Can't configure airport express with laptop after 10.5.6 update

    I can't configure airport express with laptop after 10.5.6 update
    the airport express is seen but can't access configuration screen, I get the spinning wheel forever.
    Other computer gets to the configuration screen without problem.
    And the airport utility describes the airport express like this: syAP.802.11format

    I downloaded the airport utility and re-installed
    and the problem was solved

  • How many AirPort Express stations can be supported by an AirPort Extreme wirelessly?

    I got one AirPort Extreme in my home and would like to extend the wireless network by purchasing additional AirPort Express.  Wanna know how many AirPort Express stations can be supported by an AirPort Extreme wirelessly?
    Thanks.
    Tony

    Bob -- question for you which I can't answer as I don't have an airport extreme. The newer Extremes can create both G and N networks and can create the N network in the 5 mhz band. Can you increase the number of Express units you can connect wirelessly if you split the load between the 2.4 mhz G and 5 mhz N networks created by the Extreme. (recognizing that the 5 mhz band has less range than the 2.4 mhz band)
    Not an issue for me as I only have three connected wirelessly, but I've always wondered about this. Of my three AX units one connects to a G network created by a Linksys WRT54GS and two connect to the N network created by the AX.
    So instead of 3-4 AX units could it become 6-8?
    Carlos

  • Can i use airport extreme as wifi range extender in conjunction with a Linksys AE4500 router

    can i use airport extreme base station as wifi range extender in conjunction with a Linksys AE4500 router

    If you are trying to "extend" using wireless only......Apple tells us that their "extend a wireless network" feature is designed to only work with other Apple routers.
    So, in order to use your AirPort Extreme as an extender, you would need to have another Apple router.....an AirPort Express, Time Capsule, or another AirPort Extreme as the main base station.
    I haven't tested the specific Linksys model that you have, but have owned and worked with several other Linksys models, none of which were compatible with Apple for the purpose that you ask about....so I would have to say that it is extremely unlikely that your model would be compatible with the AirPort Extreme.

  • Connecting 2 Airport Extremes wirelessly....can it be done?

    Connecting 2 Airport Extremes wirelessly....can it be done?
    I have 2 Airport Extremes. I'm only using 1 of them right now connected to a cable modem. It works well. I can get a wireless signal in most of the house and even outside a bit. However there are upstairs bedrooms on the other side of the house that I don't get a very strong signal on. No "big" deal really but here is what I thought.......
    Can I set up my 2nd Airport Extreme to wirelessly receive the signal from the 1st (main) Airport Extreme and place the 2nd Airport Extreme close to the bedrooms with weak reception? I was thinking that the 2nd AirPort Extreme could just pickup and boost my original signal.
    Is this possible? I can't find it mentioned in my Airport Manual.
    If so, what is the term for this? That way I can search for information on how to configure all of this. If you have any other ideas on how this might able to work please let me know.
    Thanks for your help

    OK, you will need to make configuration changes to both of your Extremes.
    For the main Extreme (the one connected to your modem now):
    Open AirPort Utility, click Manual Setup
    Click the Wireless tab under the icons
    Look on the wireless setup page and make sure there is a check mark next to "Allow this network to be extended". This may be under the Options tab on the wireless page. If you have a dual band Extreme, you can only extend the main network, not the 'guest" network.
    Update to save settings
    For the remote Extreme, temporarily locate it near your computer so that you can configure it:
    Open AirPort Utility, click Manual Setup
    Click the Wireless tab
    On the wireless setup page, change the Wireless Mode to "Extend a wireless network"
    You will select the name of wireless network created by your main Extreme. Enter the password if needed.
    Make sure there is a check mark next to "Allow wireless clients"
    Update to save settings
    That should do it.

  • HT4628 I recently transferred my internet service to another state. Have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the i

    I recently transferred my internet service to another state.I have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the internet. Any suggestions?

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Continue with step 2 in the first set of steps.
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Can you use airport extreme as a bridge to netgear wdnr4500 wireless router

    can you use airport extreme as a bridge with a netgear  wndr4500 router.I need to extend my wireless connections to the other side of the house

    can you use airport extreme as a bridge with a netgear  wndr4500 router.
    This is extremely unlikely. The AirPort Extreme can provide this function with other Apple routers, but as far we know, it is not compatible with products from other manufacturers for this purpose.
    Suggest that you use a Netgear product for the best chance of compatibility.

  • Can I use AirPort extreme to play musik on my sterio

    Can I use AirPort Extreme to play music from Itunes, on my sterio? Or is it just AirPort Express.?

    Express only. Only the Express has a audio jack.
    Welcome to Apple Discussions!

  • I can see my airport extreme network, but none of my devices (vista, ipad, iphone, ipod) can connect to it. Why?

    I have set up my apple aiport extreme after moving and I can see the airport extreme light is green and I can see the airport extreme network name, but when I select the network, the device cannot connect to it. No error message appears, the device simply is in a constant state of trying to connect to the network.
    I can easily connect to the non Airport Extreme network.
    Can anyone help?

    Try factory resetting, it often helps when changing location.

  • Can you use airport extreme 802.11n for files backup

    Can you use airport extreme 802.11 for files back up and sharing

    You can if you connect a hard drive that has been formatted correctly to the USB port on the AirPort Extreme.
    Apple does not officially support Time Machine backups for this type of setup, but you could store regular files this way.

Maybe you are looking for