Can't configure IPS Banner via VMS 2.3

The 5.x sensor's allows you to set a login banner with the "banner login" command on the CLI. This fills some legal obligations, but I have not found a way to set this via VMS so that I can push this out to all my sensors in one update. Please tell me VMS can do this. I do not want to configure each sensor by hand, and then have to re-import them all.

That page is part of a usefull set of pages describing how to configure the IPS Sensors using the CLI. In fact, a page from the same family discribes the CLI banner command: http://www.cisco.com/en/US/products/hw/vpndevc/ps4077/products_configuration_guide_chapter09186a008055df70.html#wp1030697
What I was asking is how to push this configuration from VMS 2.3, so I can set this option at a group level and push it out to 200 sensors in one shot.

Similar Messages

Can I not sync Calendar via USB anymore?

I just noticed that my iPad no longer syncs with the Calendar on my laptop. I did a search in the Help menu (which actually worked this time) and it said that you have to sync Calendars in Maverick with iCloud. What??? I don't use iCloud, and don't intend to.
Is this true? Hooking up the iPad to the computer no longer syncs data through the cable??

Hello Dub1_303. Welcome to the Apple Discussions!
Ok so here is what i have to work with, an action tech modem with a usb port, and a airport express connected to it via that usb port. the problem is in the airport express itself. Its not configured yet! How can i configure the AE via usb because this pc running vista doesn't have wifi? Can it be done via usb?
The AirPort Express Base Station (AX) must be connected to a DSL/Cable modem via Ethernet to function as a wireless router; the AX's USB port is only for connecting to a USB printer.
It sounds like you are attempting to use the AX as a substitute wireless card for the PC by connecting it to the PC's USB port. Sorry, but that will not work.

How can I configure my new Mac Pro to output the timeline via HDMI

How can I configure my new Mac Pro to output the timeline in FCP 7 (yes, I have X, but I'm using 7 right now). I have two monitors running from TB2, but want to have the third for a client monitor.
If I use all three via TB2, it's literally three monitors, and I want to edit on my CineDisplay. I only want the client to see the timeline video on the third monitor. When I hook up HDMI I get no signal, in fact, I can't have the HDMI cable hooked up for TB2 to work with the third.
Thanks,
GEvans
DarthPro
3.7 QCIntelXeonE5
12 GB
AMD FirePro dual D300 2048MB
OSX 10.9.2

If you use all ThunderBolt displays, or stick with DisplayPort and Mini DisplayPort (free conversion between the two with only a cheap cable) you can have up to six displays.
If you attach "legacy" displays with "any-old adapter", you can have up to two, and the built-in HDMI counts as one if you use it.
Any more requires ACTIVE Adapters.
The US$100 Apple ACTIVE Mini DisplayPort to Dual-Link DVI adapter works in every case, even displays over 1920 wide.
StarTech and Accell make US$35 ACTIVE adpters that work for displays up to 1920 wide.

Can I configure a gsm modem via bluetooth API

Hi all
Can I configure a gsm modem via bluetooth API ?
thanks in advance
Vishin Das V D

Hi deepspace
Could you please go through this thread ? http://forum.java.sun.com/thread.jspa?threadID=5211663&messageID=9860406#9860406
it will be a great help for me
Thanks
Vishin Das V D

Can Cisco Configuration Professional to use IPS feature ?

Dear Expert
Hello.
Could you tell me about Cisco Configuration Professional.
I'd like to try the IOS-IPS on Cisco2901-SEC/K9.
I was search in CCO about Cisco Configuration Professional.
The Cisco2901-SEC/K9 does not support SDM.
But, The Cisco2901-SEC/K9 supported the Cisco Configuration Professional.
Can Cisco Configuration Professional to use IPS feature like SDM?
Regards,
Takuro.

Hi,
yes, you can configure IOS IPS from Cisco Configuration Professional.
CCP has a wizard to guide you through the process, this is a link for that :
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6634/prod_white_paper0900aecd8066d265.html
i hope this helps you.
Mashal

Can't save Cisco ASA configuration in GNS3 via write memory command

Hi all,
I’m having a problem to save Cisco ASA configuration in GNS3 via write memory command.
   ciscoasa(config)# wr mem
   Building configuration…
   Cryptochecksum: c066a7ab b5b9071e bb5ee1f6 2d93be53
   %Error copying system:/running-config (Not enough space on device)
   Error executing command
   [FAILED]
   ciscoasa(config)#
Here are the details of the lab setup.
PC DETAILS:
   Windows 7 Enterprise SP1 64bit
   GNS3 v0.8.6 all-in-one (installer for 32-bit and 64-bit which includes Dynamips, Qemu/Pemu, Putty, VPCS, WinPCAP and Wireshark)
ASA DETAILS:
   13,279,888 asa802-k8.bin.unpacked.initrd
   1,095,856 asa802-k8.bin.unpacked.vmlinuz
Please advise. Thanks in advance.
http://firewallengineer.wordpress.com/2014/02/19/problem-cisco-asa-in-gns3-error-copying-systemrunning-config-not-enough-space-on-device/

instead of this:
To create a flash file
cd "C:\Program Files\GNS3\qemu-2.1.0"
qemu-img.exe create c:\FLASH 256M
try this:
To create a flash file
cd "C:\Program Files\GNS3\qemu-2.1.0"
qemu-img.exe create c:\User\usuario\GNS3\FLASH 256M
Let me know if is helpfull.

How can I configure FireFox security setting globally for all users on a PC? Is there something I can do in group policies or throught the registry to insure all users have the same settings?

Our Bank's core processor has rewritten their product to run in a web browser. Their browser of choice is Firefox 3.6. The specifications from our core processor specify specific security and settings parameters that must be adhered to by all users for their product to run properly. Is there a way to globally configure these settings via the registry or group policies to insure everyone who logs in to a given workstation opens Firefox with the same settings? Thank you for any assistance you can provide - Steve Gish, First Bank Kansas.
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729)

You can try:
*http://kb.mozillazine.org/Locking_preferences

Is there a way to enable & configure Volume Discounts via the Product Import Spreadsheet? Is there a way to enable more than 2 Quantity Thresholds?

Is there a way to enable & configure Volume Discounts via the Product Import Spreadsheet? Is there a way to enable more than 2 Quantity Thresholds?

Hi Michael,
You can set the thresholds via an import file. The easiest way to do this (and this goes for all importable data, webapps included, 301 redirects and so on) is this:
1. go into the Admin and create a single item, in you case create a test product and set the thresholds
2. export that data - in your case export the product list
3. take a look at how the data looks like in the export file so you can get an idea of how the format should be like in the import file
Unfortunately you cannot set more than 2 thresholds, that is not possible at the moment.
Thanks,
Mihai

How can I configure ReFS to NOT fail read operations when a checksum error is detected (on non-Storage-Spaces volumes where data integrity streams are enabled)?

According to William Stanek, in his Windows Server 2012 R2 Inside Out: Configuration, Storage & Essentials book, this is apparently possible: (pg. 615 - here it is on Google Books: https://books.google.ca/books?id=0IyfBAAAQBAJ&pg=PT819&lpg=PT819&dq=read+operation )
Integrity can be enabled when the system is not running on Storage Spaces. When
integrity is enabled and ReFS detects a checksum mismatch, ReFS logs an event and
fails the read operation by default. If you don’t want the read operation to fail, you
can configure ReFS to continue with the read operation. A related event will be logged
regardless.
So then how do I configure it to do that???
(And just to make it super-clear, I'm NOT using Storage Spaces, so there is no redundancy via mirroring/parity, and I'm not expecting any file repair - just detection of corruption. It's just a basic volume formatted with ReFS and
with integrity streams enabled, via format E: /fs:ReFS /i:enabled
For those who want more details, here's the situation:
I try to perform a read operation on a file with corrupted data (purposely done for testing using a low-level disk editor), I get a the following error message:
And an event ID 133 from ReFSv1 gets logged in the System log:
Clicking "Try Again" just brings up the same message, and clicking "Skip" skips the operation entirely.
This is indeed the correct default behaviour.
What I want instead is for the read operation to be allowed to complete, with corrupt data and all, and ONLY for the event to be logged. And according to William Stanek, this is supposed to be configurable somewhere - and after hours of searching, I haven't
been able to find anything.

Hi Tommy,
>>How can I configure ReFS to NOT fail read operations when a checksum error is detected
We can use PowerShell command Set-FileIntegrity to configure this. The specific parameter for controlling this behavior is
-Enforce <Boolean>which indicates whether to enable blocking access to a file if integrity streams do not match the data.
Regarding this point, the following article can be referred to as reference.
Set-FileIntegrity
https://technet.microsoft.com/en-us/library/jj218351.aspx
Best regards,
Frank Shen
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

How can i browse FP 2000 via serial port same use Ethernet port(RJ 45)?

I am a new user for labview.I develope my program with FP 2000 but I have some problem
1 How can i browse FP 2000 via serial port same use Ethernet port(RJ 45)? if it can Tell me please.
  2 If I use GSM/GPRS modem via FP 2000 rs 232 port (I under stand how to send AT command) and leave it stand alone
     Can I dial modem and browse file in FP 2000 same as use Ethernetport?
Someone please help me.Thank you very much.

Hi!
    First, I can say that your project involves many things, I cannot describe all features in the forum, and I'm not used with GPRS modems (my modems are base band serial modems...).
    Anyway, I would say that in your project you should proceed like this:
      1) Configure your FP 2000 module via MAX and ethernet connection;
      2) Download an embedded application to your module (build in LabView Real-Time)
      3) In your application, you should build a kind of serial port manager, and by the means of serial port you send/receive commands from PC.
    The commands from PC can include "Tell me the about the FP 2000 file system ", or "switch on line X", or anything you need.
   I think it would be difficult to use Internet exp, because you use IE with TCP/IP, and TCP/IP is over ethernet.
   I know that for Windows you can find some wrappers that make you "see" the serial port as an ethernet, but these wrapper do not exist under filed Point, and you shoul build one yourself!!!(and that's not easy).
    For example, to browse your files, you should build a VI that searches through your file system, and reports, via serial, the files present in a directory (it's an example....).
    About communication between GPRS modems and FP2000, I know nothing. I suppose that these modems accept serial inputs, so you'll have to configure your serial port on FP 2000 with the correct baud rate, parity, and so on..... and you send your data to the modem. The modem will transfer data in its way, no matter on how it does.
    To send data to your modem you shoud take a look to some Serial communication examples. What I suggest you, first, is to connect the serial port of FP2000 to a PC, and test communication between PC and FP2000, without modems. Just direct cable connection! If you're able to do this, insertion of modems is the next step, and should be quite easy. If you're not able to make the PC receive strings of data from FP2000, over RS232, adding modems is a further complication, and you won't come out of this mess!
   So, what I say, is just build, for now, a simple embedded application for FP2000, that, using RS232, sends data to a PC (you should see data sent with use of Hyper terminal).
    To build this application, use Instrument I/O --> VISA commands (VISA open, VISA write, and Property node should be enough, for now).
   Please, let me know if this helps......
    Have a nice (programming) day!
graziano

Setting IPs in linux VMs

Hello.
I'm having the following problem.I want to set the IPs of a linux(centos 6.4) vm but i can't.
I have a)installed the 3.4 integration services b)used kernel 3.12.5 with hyper-v support.
In both cases i always get in dmesg
hv_utils: KVP: IP injection functionality not available
hv_utils: KVP: Upgrade the KVP daemon
hv_utils: KVP: user-mode registering done.
Moreover i use the following in order to read :
$VM = Get-WmiObject -Namespace 'root\virtualization\v2' -Class 'Msvm_ComputerSystem' | Where-Object { $_.ElementName -eq "FooBar" }
$VMSettings = $vm.GetRelated('Msvm_VirtualSystemSettingData') | Where-Object { $_.VirtualSystemType -eq 'Microsoft:Hyper-V:System:Realized' }
$VMNetAdapters = $VMSettings.GetRelated('Msvm_SyntheticEthernetPortSettingData')
$VMNetAdapters
I have also tried $VMNetAdapters = $VMSettings.GetRelated('Msvm_EmulatedEthernetPortSettingData') using a legacy card.
The previous code was taken from http://www.ravichaganti.com/blog/?p=2766
In a few words i would like to assign IPs in linux VMs.
Thank you in advance!
ps:I have now seen that 3.5 version of integration services has been released yesterday and it says that it supports static ip injection.So the previous versions didn't support ip injection at all?

Hi tasoss,
I did a little bit of research and unfortunately there are only two options for you:
a) Either upgrade to CentOS 6.5
or
b) Apply the fix yourself.
The following thread further attests to the above suggestions:
https://www.centos.org/forums/viewtopic.php?f=13&t=44118
If you'd like to compile the fix yourself then you should backport the following commits:
1) Drivers: hv: util: Correctly support ws2008R2 and earlier
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/hv/hv_kvp.c?id=3a4916050ba2e0f1d114ef540abdf02b2b173e61
2) Drivers: hv: remove HV_DRV_VERSION
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/hv/hv_kvp.c?id=cfc25993e81f3fa68481d062be634d33184d5eae
3) Drivers: hv: util: Fix a bug in version negotiation code for util services
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/hv/hv_kvp.c?id=6741335bc7294548ac95cb1f4671991ff30da193
Please let me know if you need more information.
Thanks,
Abhishek Gupta, Program Manager, Linux Integration Services

How can you configure mail settings in process chains?

HI Experts,
please let me know how can you configure mail settings in process chains?

Dear Suman,
To initiate the mails we first need to have SMTP connection. To check the same go to so00 and try sending mails to ur ID. If is successful it states that u have the SMTP access.
To create mails to Process chains:
Right Click on the Process varient select the Create Message in the context menu.
Select the type of mail i.e for successful, Error, Anyways.
Then follow the screens.
Note: The recipient type should be Via Internet.
Hope this helps u.
Regards,
Kishore.Pulla

HT1145 I can't see my files on my USB shared drive. It shows there is lots of space taken up, but I can't access the files via my Mac.

I can't see my files on my USB shared drive. It shows there is lots of space taken up, but I can't access the files via my Mac. How do I see them? I also can't see them on my iPad using FileBrowser.

You don't have access to it to configure it via Time Machine? You lost me on that one, Time Machine is used for Backup.
Here is a basic article on the first setup and what you should see:
http://support.apple.com/kb/HT1178
To configure Time Capsule you should be using "Airport Utility" 5.3 or higher that is located in the Utilities folder. You can tell if its version 5.3 because the icon will have blue lines instead of orange lines like the older versions. Since you are running Leopard 10.5.6 and you ran Software Update you are probably already running the latest 5.3 version.
The light flashing amber means you haven't entered enough information so that it can get to the internet. Once you have that info entered the light will turn green.
If your absolutely sure your CAT5 cables are good you can try a hard reset. I think you have to push the reset button on the back and hold it for 5 seconds or so until the amber light blinks rapidly, then when you release the button it does the reset then.
http://support.apple.com/kb/HT1300?locale=en_US
Hope this helps! If not I would probably call AppleCare support or see if you can exchange it.
-Dan

I can't configure and create xorg.conf [ATI drivers]

Anybody have an idea HELP!!. I cannot create xorg.conf.
Follow this steps, but i can't configure this drivers. :x
My VGA is ATI 9550.
[root@nube jack]# pacman -Q ati-fglrx ati-fglrx-utils
ati-fglrx 8.25.18-1
ati-fglrx-utils 8.25.18-1
# dmesg
Linux agpgart interface v0.101 (c) Dave Jones
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[fglrx] module loaded - fglrx 8.25.18 [May 18 2006] on minor 0
[jack@nube ~]$ lsmod | grep fglrx
fglrx 382828 0
agpgart 27108 2 via_agp,fglrx
[jack@nube ~]$ fglrxinfo
Xlib: extension "XFree86-DRI" missing on display ":0.0".
display: :0.0 screen: 0
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.5 Mesa 6.4.2)
[root@nube jack]# glxinfo
glxinfo: error while loading shared libraries: libGLU.so.1: cannot open shared object file: No such file or directory
[root@nube jack]# locate libGL.so
/usr/lib/libGL.so.1.2
/usr/lib/libGL.so
/usr/lib/libGL.so.1
[root@nube X11]# aticonfig --initial --input=/etc/X11/xorg.conf
Warning: Could not find configuration file
Please copy configuration file template to /etc/X11
[root@nube X11]# Xorg -configure
X Window System Version 7.0.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 7.0
Build Operating System:Linux 2.6.16-ARCH i686
Current Operating System: Linux nube 2.6.16-ARCH #1 SMP PREEMPT Tue Jun 6 08:33:18 UTC 2006 i686
Build Date: 04 May 2006
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Jun 11 10:39:07 2006
List of video drivers:
voodoo
apm
ark
radeon
r128
ati
atimisc
chips
cirrus
dummy
vmware
glint
i128
i740
i810
imstt
mga
neomagic
newport
nv
rendition
s3
s3virge
savage
siliconmotion
sis
sisusb
tdfx
trident
tseng
via
v4l
fglrx
fbdev
vesa
vga
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
Backtrace:
0: Xorg(xf86SigHandler+0x88) [0x80ba6a8]
1: [0xffffe420]
2: /usr/lib/xorg/modules/drivers/fglrx_drv.so(R200Probe+0x124) [0xb72fdbd4]
3: Xorg(DoConfigure+0x140) [0x80ace60]
4: Xorg(InitOutput+0x615) [0x80a2b45]
5: Xorg(main+0x293) [0x806fbf3]
6: /lib/tls/libc.so.6(__libc_start_main+0xd0) [0xb7d9ae00]
7: Xorg(FontFileCompleteXLFD+0x91) [0x806f341]
HELP please!!.
Regards.

Ok, i installed hwd and create in /etc/X11 the file xorg.conf.hwd
Now....
[jack@nube ~]$ sudo X -configure
X Window System Version 7.0.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 7.0
Build Operating System:Linux 2.6.16-ARCH i686
Current Operating System: Linux nube 2.6.16-ARCH #1 SMP PREEMPT Tue Jun 6 08:33:18 UTC 2006 i686
Build Date: 04 May 2006
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Jun 11 21:21:45 2006
List of video drivers:
voodoo
apm
ark
radeon
r128
ati
atimisc
chips
cirrus
dummy
vmware
glint
i128
i740
i810
imstt
mga
neomagic
newport
nv
rendition
s3
s3virge
savage
siliconmotion
sis
sisusb
tdfx
trident
tseng
via
v4l
fglrx
fbdev
vesa
vga
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
Backtrace:
0: X(xf86SigHandler+0x88) [0x80ba6a8]
1: [0xffffe420]
2: /usr/lib/xorg/modules/drivers/fglrx_drv.so(R200Probe+0x124) [0xb7304bd4]
3: X(DoConfigure+0x140) [0x80ace60]
4: X(InitOutput+0x615) [0x80a2b45]
5: X(main+0x293) [0x806fbf3]
6: /lib/tls/libc.so.6(__libc_start_main+0xd0) [0xb7da1e00]
7: X(FontFileCompleteXLFD+0x91) [0x806f341]
Fatal server error:
Caught signal 11. Server aborting
[jack@nube ~]$ aticonfig --initial --input=/etc/X11/xorg.conf
Warning: Could not find configuration file
Please copy configuration file template to /etc/X11
What's happening.... :?: :?: :?:

Can't configure spam filters

Hi, my father recently acquired a blackberry from the university of Granada (UGR) and i should be able to enter to http://blackberry.orange.es/ but after entering my PIN / IMEI i get an error saying i can't acces with an HTML client but directly through the blackberry, i tried this way but all i get is the configuration page of the beginning where there are no filter options whatsoever. Where and how can i configure the spam filters??
Solved!
Go to Solution.

Hi and Welcome to the Forums!
Try finding your BIS logon page via this portal:
http://www.blackberryfaq.com/index.php/Where_can_I_log_into_my_BIS_account%3F
BTW -- BIS does not have a spam filter per se. What it has are filters you can create one by one -- filter out a sender address, filter out a subject line. But it is not a full spam filtration system. For that, you have to see the owners of the email service being used and see what server-level spam filtration they can offer.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Can't configure IPS Banner via VMS 2.3

Similar Messages

Maybe you are looking for