Can't configure WRT160N
Hello All
I have a WRT160N that I used just once after purchase (my ISP gave me a wireless router). I could not remember the PW, so I reset. (The computer saw the old router name but I had no PW)
When I run the software (CD that came with the product says 150N), it get to "configuring computer" and stops there.
I tried downloading the software, but when I try to run it says "Application requested runtime to terminate in an ususula way."
When I go to the 192. URl and try to login using a bank user name and 'admin," it jsut keep bringing up the password box.
Any suggestions? Thanks!
There's a possibility that the router is already bricked. Try this reset: press and hold the reset button using a pin or a paper clip for 30 seconds; while still holding the reset button unplug the power cord from the router for another 30 seconds; while still holding the reset button plug the power back in; wait for another 30 seconds then let go of the reset button. Once the power light goes solid, connect a computer directly to one of the lan ports of the router then check if you can access its setup page. if you are able to reconfigure then the settings of the router. Since the setup cd seems to be not for this router, reconfigure the router manually by following the steps on these links: ng up a Linksys router with Cable Internet service & Setting up a Linksys router for DSL Internet connection.
Similar Messages
-
Configuring WRT160n router to maximize range and speed
I have just bought and installed a WRTn160 router. I used the default configuration settings. Unfortunately, I realized that on my second floor, one computer (g) did not pick up the signal and the other computer (n) was extremely slow. On the contrary my old LinkSys (b) router worked just fine with both machines. I then changed the 'Wide' channel to 20MHz and used channel 6 (the default was 'Auto'). This improved the speed on the second floor considerably. My questions are:
1- How do I know if the computer supporting 802.11n is actually using it? The manual indicates that 20MHz is for b/g only.
2- If this configuration is supporting b/g only, how can I configure the router to support (n) computer while still supporting the (g) computer and maintaining range and speed?
3- How can I test for bandwidth between my desktop and the two other wireless computers? Currently, I only test bandwidth using my ISP. Needless to say, this is limited to bandwidth for Internet connectivity.
4- Advertisement for n routers indicate increased speed and range. This has not been my experience, in fact to the contrary, range dramatically shrunk. Is this limited range a configuration issue? a WRT160n router issue? or a limitation with the technology (802.11n)?I would suggest you to readjust the wireless settings of the router...
On the setup page,click on the Wireless tab,Change the channel to 11 and click on save settings..Under Wireless tab,click on Advance Wireless Settings tab and Change N document.write("Transmission Rate")Transmission Rate to 15-130Mbps, Change the Beacon Interval to 75, Fragmentation Threshold to 2304,RTS Threshold to 2304 and Click on save settings... Under Security tab,uncheck " document.write("Filter Anonymous Internet Requests")Filter Anonymous Internet Requests"...Power cycle the network and check the result. -
I asked at a Hong Kong apple shop if they had password protected external drives. They didn't, I bought one anyway.
I'm wondering can I configure this drive. If yes, what do I need to do?This looks like the easiest and most direct method and since it uses Disk Utility it would work on any OS.
http://osxdaily.com/2012/01/25/password-protect-external-drive-mac-encrypted-par tition/ -
please help!! how can i configure my iphone 3gs because i've been updated a new version, i did it but it's hard to activate it again. this message i always recieved in my iphone
"We're sorry, we are unable to continue with your activation at this time."You phone was hacked. You can not get help with it here. Hacking / Jailbreaking voids any warraty and forfeits your right to support. Discussing jailbroken / hacked devices is forbidden by the terms of service here.
-
With an 11"-inch Macbook Air (mid-2012) using a mini DisplayPort-to-VGA adapter plugged into the Thunderbolt port:
Can you configure an extended desktop with an external monitor (20") displaying full portrait mode (1200 x 1600 resolution) and keep the built-in display in landscape?
I'd like to see something like
External monitor / Built-in displayYes, I can't see why not.
Just give it a try and report back if you have a problem. -
How can I configure iCloud so it doesn't restore deleted or moved emails on my Mac?
I moved to iCloud, and so far it looks like everything is where it's supposed to be. My question is about syncing. When I delete an email on my Mac, iCloud restores it. How can I configure iCloud so that changes I make on my Mac and my iPhone stay changed?
On the Mac in System Preferences > iCloud
Make sure Mail & Notes is selected.
ON the iPhone tap Settings > iCloud
Make sure Mail is switched on.
And try restarting your Mac and iPhone. -
How can I configure my new Mac Pro to output the timeline via HDMI
How can I configure my new Mac Pro to output the timeline in FCP 7 (yes, I have X, but I'm using 7 right now). I have two monitors running from TB2, but want to have the third for a client monitor.
If I use all three via TB2, it's literally three monitors, and I want to edit on my CineDisplay. I only want the client to see the timeline video on the third monitor. When I hook up HDMI I get no signal, in fact, I can't have the HDMI cable hooked up for TB2 to work with the third.
Thanks,
GEvans
DarthPro
3.7 QCIntelXeonE5
12 GB
AMD FirePro dual D300 2048MB
OSX 10.9.2If you use all ThunderBolt displays, or stick with DisplayPort and Mini DisplayPort (free conversion between the two with only a cheap cable) you can have up to six displays.
If you attach "legacy" displays with "any-old adapter", you can have up to two, and the built-in HDMI counts as one if you use it.
Any more requires ACTIVE Adapters.
The US$100 Apple ACTIVE Mini DisplayPort to Dual-Link DVI adapter works in every case, even displays over 1920 wide.
StarTech and Accell make US$35 ACTIVE adpters that work for displays up to 1920 wide. -
How can I configure printer with iPad to print only grey tones? This works fine from my laptop - not air printing from that one though. I can't find anywhere on the iPad how to do printer settings and this also seems not to be available as an option when doing a printout. In fact, no options seem to be available. Thanks in advance for reacting!
HermiThere is currently no option for this. You can give Apple feedback here:
http://www.apple.com/feedback/ipad.html -
According to William Stanek, in his Windows Server 2012 R2 Inside Out: Configuration, Storage & Essentials book, this is apparently possible: (pg. 615 - here it is on Google Books: https://books.google.ca/books?id=0IyfBAAAQBAJ&pg=PT819&lpg=PT819&dq=read+operation )
Integrity can be enabled when the system is not running on Storage Spaces. When
integrity is enabled and ReFS detects a checksum mismatch, ReFS logs an event and
fails the read operation by default. If you don’t want the read operation to fail, you
can configure ReFS to continue with the read operation. A related event will be logged
regardless.
So then how do I configure it to do that???
(And just to make it super-clear, I'm NOT using Storage Spaces, so there is no redundancy via mirroring/parity, and I'm not expecting any file repair - just detection of corruption. It's just a basic volume formatted with ReFS and
with integrity streams enabled, via format E: /fs:ReFS /i:enabled
For those who want more details, here's the situation:
I try to perform a read operation on a file with corrupted data (purposely done for testing using a low-level disk editor), I get a the following error message:
And an event ID 133 from ReFSv1 gets logged in the System log:
Clicking "Try Again" just brings up the same message, and clicking "Skip" skips the operation entirely.
This is indeed the correct default behaviour.
What I want instead is for the read operation to be allowed to complete, with corrupt data and all, and ONLY for the event to be logged. And according to William Stanek, this is supposed to be configurable somewhere - and after hours of searching, I haven't
been able to find anything.Hi Tommy,
>>How can I configure ReFS to NOT fail read operations when a checksum error is detected
We can use PowerShell command Set-FileIntegrity to configure this. The specific parameter for controlling this behavior is
-Enforce <Boolean>which indicates whether to enable blocking access to a file if integrity streams do not match the data.
Regarding this point, the following article can be referred to as reference.
Set-FileIntegrity
https://technet.microsoft.com/en-us/library/jj218351.aspx
Best regards,
Frank Shen
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] -
Can't configure wireless settings on P1102w using a mac
Hi there. I can't configure wireless settings on P1102w using a mac. I have it installed with USB just fine but I want to use eprint (with ios airplay). I run the setup utility looking for some wireless setup option, but it never appears. When I finish the install it tells me to go to the eprint website to download eprint. At that site it has me download the firmware update, which I do, and then at the end of that it tells me to go to the eprint website again, which then downloads the firmware update again. It's an endless loop.
I know I need to get to the built in web server but the config page tells me I don't have an IP address. Which makes sense to me because it hasn't been set up. I can't for the life of me find how to set up the wireless using the driver software on the Mac OS. I try to follow the manuals instructions, but it looks like it is designed for windows users, and the buttons it tells me to look for just don't exist on the mac HP driver software.
Can you help?Hi,
The Wireless configuration should be made by using the EWS page, which also accessible from Mac OS over a USB connection through the printer setup.
You may find the steps listed below:
Click the Apple icon, then clickSystem Preferences.
Click Print & Fax.
Select your printer and click Open Print Queue.
Click on Printer Setup
Then select Utility
Click Open Printer Utility
Click HTMLConfig. The EWS opens.
Click the Networking tab
Then click Wireless from the list on the left
Under Communication Mode, click Infrastructure, select your network SSID from the Available Network Names (SSID) list, and then click the << button.
From the Security Mode pop-up menu under Authentication, click WEP or WPA/WPA2. Your selection depends on which Wireless Security Protocol your network uses.
Type your WEP/WPA/WPA2 key in the appropriate field, and then click Apply.
In the confirmation box, click OK and then close the HTML Config and Print Queue windows.
Once done, allow 3 minutes to fully establish the connection, then unplug the USB.
Enter Print & Fax and remove the existing USB Print Queue.
Click the Plus button and add the printer over the network.
Please let me know of any issue,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
How can I configure a VM to boot from USB key in Virtual PC of Windows 7?
Hi all,
I want to boot up with a USB key to install a new VM on Windows 7. I heared that Microsoft Virtual PC begins to support USB device on Windows 7. How can i configure it? I don't find any virtual USB device in VM settings on my Windows 7 box.
Thanks for any help.
Scorprio
TechNet Software Assurance Managed Newsgroup MCTS: Windows Vista | Exchange Server 2007 MCITP: Enterprise Support Technician | Server & Enterprise AdminHi all,
I want to boot up with a USB key to install a new VM on Windows 7. I heared that Microsoft Virtual PC begins to support USB device on Windows 7. How can i configure it? I don't find any virtual USB device in VM settings on my Windows 7 box.
Thanks for any help.
Scorprio
TechNet Software Assurance Managed Newsgroup MCTS: Windows Vista | Exchange Server 2007 MCITP: Enterprise Support Technician | Server & Enterprise Admin
Virtual PC does not support USB. Windows 7 XP Mode Virtual Machine supports the use of USB devices. Virtual PC and Windows 7 XP Mode VM are not the same thing! -
HT1277 How many mail accounts can I configure in "Mail" on my mac book pro ?
Im trying to open multiple mail accounts in "Mail" but am unable to. How many mail accounts can I configure ?
http://support.apple.com/kb/TS3276
http://support.apple.com/kb/HT1277
http://www.apple.com/support/macosx/mailassistant/
should be as many as you want
http://www.dummies.com/how-to/content/adding-a-new-mail-account-in-mac-os-x.html -
Can not configure Oracle 10g form on oracle 11g client
Hi
I need to install oracle 10g form in my system .
Here is my system
1. OS --XP
2. 32 Bit
4. Already oracle 11g release client installed ( I think that create the problem )
I tried to install oracle 10g form , it installed but can cont configure net manager for it , Always it point to 11g client and hence I could not configure .
Also I tried install Oracle Forms first then 11g client , But I got same issue .
I think if I created multiplr home one for 11g client and other for forms , it may work out .
Please help me
DebashisWhile deploying the example 'VacationRequest' in the oracle complete guide for 11g, i got an exception like this
"12:08:15 PM] Deploying Application...
[12:11:16 PM] [Deployer:149191]Operation 'deploy' on application 'VacationRequestTaskFlow' is initializing on 'soa_server1'
[12:11:24 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application VacationRequestTaskFlow on soa_server1.: [Deployer:149145]Unable to contact 'bam_server1'. Deployment is deferred until 'bam_server1' becomes available.; nested exception is:
java.rmi.UnknownHostException: Could not discover administration URL for server 'bam_server1'.
[12:11:24 PM] [Deployer:149193]Operation 'deploy' on application 'VacationRequestTaskFlow' has failed on 'soa_server1'
[12:11:24 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application VacationRequestTaskFlow on soa_server1.: Failed to load webapp: 'VacationRequestTaskFlow.war'.
[12:11:24 PM] Weblogic Server Exception: weblogic.application.ModuleException: Failed to load webapp: 'VacationRequestTaskFlow.war'
[12:11:24 PM] Caused by: java.lang.ClassNotFoundException: oracle.adf.library.webapp.ResourceServlet
[12:11:24 PM] See server logs or server console for more details.
[12:11:24 PM] weblogic.application.ModuleException: Failed to load webapp: 'VacationRequestTaskFlow.war'
[12:11:24 PM] #### Deployment incomplete. ####
[12:11:24 PM] Deployment Failed"
Can anyone help in this. -
Can´t configure secondary e-mail. That is I have the icloud account and earlier bought an account för my wife. Now she can´t get it to work. Where the h--l do I configure this?
Welcome to the Apple community.
If you are referring to adding a secondary account, to a single device, then you can do this at system preferences >mail, contacts & calendars. -
How can i configure advance payment to vendors through cash jounal
how can i configure advance payment to vendors through cash jounal pls its urgent for me kindly help me out
HI,
I think u need not configure anyting new for this, you can use the existing Business Tran. Type K and rename it as Vendor Advance for separate identity. You can do the normal FBCJ posting.
But doing this you will not have separate identity for the Advances paid.
Thanks
VK
Maybe you are looking for
-
How can I prevent Applications from being copied to external drive?
Hello, Just a quick one... I run a studio in an education evironment. We've got quite a lot of software installed on our machines (Mac OS X 10.7.4) and there's always the chance that students will copy applications from the Applications folder onto a
-
STMS error after language pack
Hi after language pack updated i am getting transport error please do the needfull thanks
-
i'm forgot my pass code how to unlock my iPad Air iOS 8.2 when i connect to iTunes i got a message turn find my iPad off first !!!
-
Just got back my iMac with a brand new replacement hard drive through the iMac 1 TB Seagate Hard Drive Replacement Program. With only apps installed, no files and fonts added, the hard drive already shows permission problems. Is that normal? The repl
-
Record a Macro in LabVIEW :) ?
Hi All, I was asked recently if there's any way to "record" a series of operations on the front panel and save them off for later re-execution within LabVIEW... possibly using VI server, or some such? E.G. Click button 1, change value of input numeri