Can't Connect ASDM and Console Forces User Name: & Password: Prompts

After pulling a brand new ASA 5515 out of the box this morning, I spent countless hours scratching my head wondering why:
1. I cannot establish an HTTPS connection to the Management port - https://192.168.1.1/admin
2. When connecting via the console port I get prompted with a username and password sequence that I don't know
I get an SSL Version Error message when I try to connect with any browser. although I did find a way to resolve it, it requires a console port connection which is not working either.
This is not my typical experience with the console or ASDM port setup. What is going on? Any help from anyone would be so appreciated.
Thank you,
Richard

Hmm,
To my understanding Console connection on a fresh unit shouldnt ask for a username and it shouldnt even have an enable password (should be able to leave it blank and press enter). Or atleast that is how I remember it.
I am not sure if the new ASA5500-X models are different.
I think on when using ssh (or was it telnet) without username configured required you to use username pix and password cisco to log in.
- Jouni

Similar Messages

  • Windows Security user name/password prompt when trying to remote access personal cloud storage device

    I have 2TB WD Book Live drive setup at home and is working fine, including remote accessing by internet. However using a colleague's computer at the office recently, her computer would always prompt me for Windows Security username and password. I've tried
    keying her admin user name/password and well as the router's admin/admin combinations and still doesn't allow me to access the cloud drive properly. However I have had no problem accessing the same drive remotely using other colleagues computers.
    The exact message prompt as follows: Windows Security. The server 192.168.1.1 is asking for your user name and password. The server reports that it is from index.htm. WARNING: Your user name and password will be sent using basic authentication on
    a connection that isn't secure.
    Please help me understand the problem and its solution. Thank you.

    Hi,
    The IP address 192.168.1.1 is your Router server address, isn't it? I doubt there should some limition in your colleague's system. Please check it. Also you can try to disable security software for test to access your cloud.
    The problem isn't your cloud server Authorization.
    Roger Lu
    TechNet Community Support

  • User name password prompt is not working

    Hi Experts,
    I have a screen in a BSP application in which , I have two links.
    These two links are the links to the screens of a different BSP application for which default username password is not set.
    But when I clicked the first link its prompting for the user name and password but its not happening for the second link.
    Its also vice versa.
    I checked the below link which explains about the way password details are prompt but I am not sure of how to handle this and have the prompt for username and password for both the links.
    http://help.sap.com/SAPHELP_470/Helpdata/EN/5a/f8b53a364e0e5fe10000000a11405a/frameset.htm
    Your inputs will be helpful.
    Regards,
    Gopal

    Hi,
    this sounds a case for Single Sign On, especially if you´re calling your 3 applications from the Enterprise Portal. You have to talked to your administrators for EP and SAP, since it is a complicated task.
    Try this link for more about the user and this link for SSO.
    after entering username and password for the first time, somehow the information remains alive event when you close your BSP application and call another one. This is a very bad security case if you´re moving your applications into production.

  • HT203808 Mixed up iCloud and Apple ID user names/passwords

    My daughter and I had been sharing iCloud for our phones.  I created a new email account for her and told her to set up her own iCloud on her phone. I told her to delete the account  (mine) listed on her phone and then to go back in and create a new account. I have no idea what she did. She seems to have changed my account to her email address. I thought I finally had it figured out after going back and forth in emails because it didn't recognize my password. Changed the password, I can get on and when I go to manage storage, it just shows my phone...and 5gb of storage even though I pay for 10 extra and it always shows 15gb. Is all the information now on her phone?  This is so frustrating. When I went on iCloud I checked and my email address is the only one listed. However, when I tried to create a new apple id using her new email address it said that the id already existed, which I'm sure it does- with all of my information. She, even though she created the stupid thing 20 minutes ago, "can't remember her password."  UGH.  Any ideas?

    Okay so what she did was she CHANGED my iCloud id to her new email and all of that information went with her.  So her ID shows the 15gb of storage. How do I change it back? It won't let me online.

  • Restrict the User name / Password Auto complete option for users accessing

    Hi All,
    Can any one know the Restrict the User name / Password Auto complete option for users accessing Portal from within and outside of Portal.
    Regard's
    Rama

    Are your referring to the browser functionality of remembering the usernames and passwords?
    Thanks,
    GLM

  • Default User name & Password for NETWEAVER

    Hi Everybody,
                  I am a Basis Admin in my company working with ABAP Stack installed in my Server.
           Now I have installed Java Stack for Netweaver in a Separate System to Understand the Functionality of Netweaver & its Concept.
         Now the Problem is i am not able to Login Netweaver. I dont know the Default User name & Password for Netweaver after installing it.
        Also, what are the Main features of Netweaver Compare to ABAP Environment
      Could somebody help me to Understand Netweaver and its Default User name & Password to login?
    Thanks,
    Siva

    Hi
    The default asmin user for your Java add in would be J2EE_ADMIN and guest user would be J2EE_GUEST.
    The default password would be the password you provided at the time of installation.
    Regarding information on Netweaver Java, follow link:
    http://help.sap.com/saphelp_nw04/helpdata/en/0d/a3bb3eff62847ae10000000a114084/content.htm
    Regards
    Rahul

  • Can not connect to MaxDB 'Unknown user name/password combination' returned

    Hi,
         I try to make a connection from NWDS 7.2 to MaxDB. So i use the url as 'jdbc:sapdb://127.0.0.1:7210/CE1' to make a connection (by wizard of data source explorer in NWDS).
    I try to entry username and password as below :
    User : 'Administrator' , Pass : 'admin123'
    User : 'SAPJ2EDB' , Pass : 'admin123'
    User : 'superdba' , Pass : 'admin123'
    User : 'control' , Pass : 'admin123'
    So i always got
    com.sap.dbtech.jdbc.exceptions.jdbc40.SQLInvalidAuthorizationSpecException: [-4008]: Unknown user name/password combination
    returned
       I quite sure that 'admin123' is the password for MaxDB because when i try to uninstall the MaxDB it ask me to input password for 'superdba' and 'control'
    How should i do? I remember that when i installed the SAP CE7.2 i had entered just only one password.
    How can i reset the username and password or use default password?
    P.S i try to enter user and pass from this post MAXDB Server,Database,Username and pasword , but it still not work .
    Edited by: Thongie on Jul 14, 2011 2:48 PM

    Hi every one,
        I can solve it. I just restart DB and try agian.

  • We have an itunes account on our desktop and my kids have it on their ipod and iphone. I went in and changed our user name from my old e-mail address which is no longer accessible to my new one and now either of my kids can access the itunes store..

    We have an itunes account on our desktop and both my kids have it on iphone and ipod. I went in and changed out user name from an old e-mail address which is no longer accessible to my one I use now... When the kids try to sign onto the itunes store it tells them they have the wrong user name..
    Can this be fixed??

    Did you change the email address or create a new Apple ID?
    If the email address associated with the account was merely changed, sign out of the Apple ID on the devices and sign in using the new credentials.

  • Can i connect imac and macbook by usb?

    can i connect imac and macbook pro by using USB clable? i just want pass my files and music from macbook to imac.
    thank you

    You can't connect both computers by USB. The easiest way is to connect them using a FireWire cable (if your iMac and your MacBook Pro have got FireWire ports), and put your MacBook in target disk mode (start your MacBook holding the T key).
    Doing this, the iMac will detect the MacBook's hard disk as an external disk, so you can easily access to your files from Finder and copy the data you want to the iMac's hard disk

  • Can we connect Multisim and LabVIEW?

    Hi frndz 
    I want some info.  please tell me is there any such facility in LabVIEW2011 that i can use circuit from Multisim as a simple camponant in LabVIEW???
    take 1 example :
        suppose i m doing HOME AUTOMATION  project. in that i have  my own temp. sensor circuit , light detector circuit. i made these circuits in Multisim.
    now  i want to use that circuit as a single block in LabVIEW???
    can we connect Multisim and LabVIEW?

    Hi,
    I believe what you are looking for is Multisim connectivity toolkit.
    This should help : http://zone.ni.com/devzone/cda/tut/p/id/7785
    Sahil

  • Why I can not connect ipad2 and iphone5 to wifi by using d-link modle? but my computer and iphone3 can do it.

    why I can not connect ipad2 and iphone5 to wifi by using d-link modle? but my computer and iphone3g can do it.

    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting
    http://www.apple.com/support/ipad/wifi/
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • HT3986 After installed win7 on my mac pro(mid 2012/mountain lion), I can not connect internet and where can i find drivers in mountain lion system

    After installed win7 on my mac pro(mid 2012/mountain lion), I can not connect internet and where can i find drivers in mountain lion system.
    I donot think I have a install disk when I bought my mac, there is only a disc partition for recovery system.

    Welcome to the Apple Support Communities
    You have to install Boot Camp drivers. On Mountain Lion, you have to download them.
    First, press X key while your Mac is starting to start into OS X. Then, open Boot Camp Assistant and select the option to download the drivers. You will have to burn them into a DVD or USB drive, so after downloading them, restart and install them into Windows

  • HT1515 Will Airport Express work in hotels in China? They require user name/password to connect. Has anyone used one there?

    I will be traveling in China with my iPad2 and want to use hotel wireless. It requires a sign-in with user name/password.  Can I use an Airport Express for this purpose? How do I set it up for that? I have an old Express (pre-2007); can I use it or do I need to upgrade to the new model?

    OK - I have never been to China but the posts here say that it can be done - the cable from the hotel should be connected to the WAN port of the Express - the Express should be in bridge mode and set to create a wireless network with a name and password of your choice - you can do this with a computer before you leave for China or with the iPad if you have previously downloaded the Airport Utility app - you would then connect to your network and attempt to bring up a web page such as Google - the hotel should then intervene and ask you for the login info that they have provided.
    Charlie

  • My app store is not working after installing mavericks. When I open app store it repeatedly asking me to login with apple ID and to provide User name and Password for proxy authentication in a loop.I am a newbie to mac,Please help me.

    My app store is not working after installing mavericks. When I open app store it repeatedly asking me to login with apple ID and to provide User name and Password for proxy authentication in a loop.I am a newbie to mac,Please help me.

    Hmmmm... would appear that you need to be actually logged in to enable the additional menu features.
    Have you tried deletting the plists for MAS?
    This page might help you out...
    http://www.macobserver.com/tmo/answers/how_to_identify_and_fix_problems_with_the _mac_app_store
    Failing that, I will have to throw this back to the forum to see if anyone else can advise further.
    Let me know how you get on?
    Thanks.

  • Question on how to Hide the User Name, Password, and Domain fields in the MDT Wizard

    MDT 2012 U1
    Deploying Windows 7 via Offline Media (ISO) to MS Virtual PC's
    I am looking on how to Hide the User Name, Password, and Domain fields which are prepopulated in the MDT wizard via the CS.ini (Not so concerned about the Domain field as I am User Name and Password)
    We do need the Computer Name and OU fields to be seen, so skipping the wizard is not a option
    The client just does not want these fields to be seen by the end users, they dont want them to even know the account name used for adding the machine to the domain, of course the password is not displayed but it must not be displayed either.
    But since we use the fields they must still  be fuctional just not seen.
    Thanks.....
    If this post is helpful please click "Mark for answer", thanks! Kind regards

    You shouldn't have to edit DeployWiz_Definition_ENU.xml. You should only need to add "SkipAdminPassword=YES" to the CS.ini file and your authentication information.
    Example:
    [Settings]
    Priority=Default
    Properties=MyCustomProperty
    [Default]
    OSInstall=Y
    SkipCapture=NO
    SkipAdminPassword=YES
    UserID=<MyUserID>
    UserPassword=<MyPassword>
    UserDomain=<MyDomain.com>
    SkipProductKey=NO
    SkipComputerBackup=YES
    SkipBitLocker=NO
    -Nick O.
    Nick,
    SkipAdminPassword=YES is for:
    You can skip the Administrator Password wizard page by using this property in the
    customsettings.ini.
    I am hidding the Username/Password/and domain field in the computer name Wizard pane which is read from the cs.iniDomainAdmin=xxxxx
    DomainAdminPassword=xxxxx
    DomainAdminDomain=xxxxxx
    JoinDomain=xxxxxx
    If this post is helpful please click "Mark for answer", thanks! Kind regards

Maybe you are looking for

  • Stock on posting date-MB5B

    Hi! I'm looking for a function that works as MB5B, I need to calculate the stock on posting date, I used the debugger, but I couldn't find a function. Thanks!

  • HT1923 I can't delete the Apple folder in Common Files

    My computer would not recognize my iPhone.  I tried the troubleshooting tips found online, uninstalling everything in order.  When verifying all files had been removed, I could not delete the Apple folder in Common Files as it says the folder or a fi

  • Can you please help me out with the answers

    u2022     Created a report to display details of the Open Picking Slip for a given Shipping Point and Delivery Date. u2022     Developed a report program for stock details in various storage locations. Which displays material number, material group,

  • Urgent!! Navigation from a link to a Zviewset

    Hi Experts, I have created a link on standard veiw(followupdetails).On click of this link a new zview should open. I have created a new zviewset (zcharity) within which it contains zview( zcalendar). I have made the folloing entires in design time re

  • Setting fixed the exchange rate field (KUFIX) ticked by default me21n

    In the transaction ME21N to create purchase orders, there is a field to fix the exchange rate (KUFIX). We want to set this field to 'X' as default value, when the user call the transaction. Does anybody know a user exit or a BADI where I can modify/s