Can't connect more than one PC to my network at the same time.

When trying to connect a second wireless laptop to my network, the one already connected gets disconnected. I'm using a WRT110 router(cable connection) that I bought 5 days ago, and two laptops with Win Vista. I don't have any PC wired connected.

First thing which you need to do is upgrade the firmware of your Router. Go to website linksysbycisco.com/downloads... ......insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop..
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Once you configure all the settings on your router... here are some wireless settings which you can set on your Router and i think this might make your both the wireless computers go Online...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Similar Messages

  • Can I have more than one version of adobe reader at the same time?

    can I have more than one version of adobe reader at the same time?

    If I may add a qualification: on a device running full Windows 8, you may have both Adobe Reader Touch and Adobe Reader (normal desktop edition). This does not apply to the primitive devices which cannot run desktop apps (running "Windows RT"), and while I may be wrong, I believe that the Surface 2 is such a device.

  • Can I pair and use more than one set of bluetooth speakers at the same time on my ipod touch 4.0

    can I pair and use more than one set of bluetooth speakers at the same time on my ipod touch 4.0 or Iphone 4s or Ipad 2?

    You can only connect to one device at a time using Bluetooth, See article below for more information.
    http://support.apple.com/kb/ht1664
    While your iOS device can maintain multiple pairing records, it can only connect to one headset or hands-free device at a time. This prevents your iOS device from sending your data to the wrong Bluetooth accessory.

  • Can I configure my Bluetooth connections to use more than one wireless audio output device at the same time?

    I am trying to get my Macbook Pro (OS X 10.8.5) Bluetooth system to recognize 2 different wireless speakers at the same time. both are currently paired with mu computer and can be chosen independently and work nicely.

    Version 10.0.3 is the latest version of iMovie. iMove '11 (as in 2011) is version 9.
    iMovie saves your Projects automatically. So you can just choose to create a new Project. Your existing Projects will remain available for you to go back to whenever you like.
    You can have as many Projects as you like. You don't need ot finish one before you begin another.
    Post back if you have specific questions.
    Matt

  • Can more than one child be visible/open at the same time in Accordion navigator container?

    I have a situation where I need a layout like Accordion
    container but with more than one child panel visible at the same
    time. Is it possible with Accordion container? If not, any
    suggestions to implement this layout?

    Ryan,
    Could you elaborate on what you mean when you say that the program which ran first cannot find its report?  Are you trying to modify the same report simultaneously with these different apps?
    Regards,
    Jared Boothe
    Staff Hardware Engineer
    National Instruments

  • How to control more than one instrument via different interfaces at the same time

    Hi, I am new to Labview.  I am working in a project where I have to make a Automated testing tool . So, here is the set up -  I have a Chip on a board to which there are several instruments connected namely Agilent power supply, Agilent pattern generator, oscilloscope,Dmm and Thermotron. All these instruments will be connected to the host computer via ethernet, GPIB or RS232. I have to write a program on Labview where the program  should be able to communicate with these  instruments  at  the same time  and show the ouput  on display unit . I have to run the program once, should be able to view the ouputs. So, Is it possible to write such program in Labview??.  I have  downloaded  few instuments  drivers. Is it possible to combine those intrument drivers and construct a new VI which would be able to control all this ??   Will it be easier to program this on Labview or  I should  go for Labwindows/CVI  ??.
    Please mention some useful sites or tips (if u know) for writing program.
    Thanks in advance
    shasanka

    Hi Shasanka,
    ofcourse it's possible to control more than one instrument at a time.
    You should use the VISA routines to access all your devices. Every device get it's 'address' as 'VISA resource name'. This resource name contains information on the used bussystem and the (internal) device address (i.e. GPIB devices have an address number).
    So I suggest to read the manual and to look at the examples that come with LabView!
    And (from your question) it seems you should take the 3 or 6 hour seminar as well! (Look at www.ni.com -> academics.)
    Best regards,
    GerdW
    CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
    Kudos are welcome

  • How do I log into more than one email account and view at the same time?

    In the past, I could log in to hotmail.com and open and view more than one email account in firefox. I must have closed something, so now I can't do that?
    HELP???

    Hi Shasanka,
    ofcourse it's possible to control more than one instrument at a time.
    You should use the VISA routines to access all your devices. Every device get it's 'address' as 'VISA resource name'. This resource name contains information on the used bussystem and the (internal) device address (i.e. GPIB devices have an address number).
    So I suggest to read the manual and to look at the examples that come with LabView!
    And (from your question) it seems you should take the 3 or 6 hour seminar as well! (Look at www.ni.com -> academics.)
    Best regards,
    GerdW
    CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
    Kudos are welcome

  • More than one programs using report generator at the same time

    Hi,
    I want to ask that how can I use Report Generator in two program at the same time.
    As I am using Report Generator to log my data into excel, I find that if there are two
    programs contain Report Generator, the program which ran first cannot find its
    report.What can I do apart from alway open a new report?
    Ryan

    Ryan,
    Could you elaborate on what you mean when you say that the program which ran first cannot find its report?  Are you trying to modify the same report simultaneously with these different apps?
    Regards,
    Jared Boothe
    Staff Hardware Engineer
    National Instruments

  • Can I connect my Mac to two separate wireless networks at the same time?

    Need some assistance with some advanced wireless networking please....
    Upstairs I have a D-link wireless router connected to the internet and wired to a couple of PCs. Downstairs I have a minimac linked to my hifi via an airport express. I have bought a D-Link DWL-G122 usb wifi dongle.
    So I want the mini mac to connect to the airport express on one wireless network (strong signal) and to be able to connect to the internet on another network (weak signal) via the usb wifi /router.
    But the airport software and the d-link driver seem to conflict and both try to take control of the two wireless devices.
    Is there any way round this to be able to run one mac with two wireless network devices at the same time?
    Thanks

    While those with more experience may be able to correct me, I'm pretty sure that you can only connect to one wireless network at a time with your Mac Mini, unless D-Link provides their own proprietary software that bypasses the computer's Airport settings.
    Using the AirPort hardware you can only connect to a single wireless network at any given time. However in this situation the 2 attempted connections are via USB and AirPort. Therefore this requires nothing special of the AirPort drivers or settings.
    It does require that the Mac OS and applications have the capability to use either network connection (USB or AirPort) depending on what data they are trying to get. In general I understand how it is theoretically possible but I have no idea if you can configure OS X to do it.
    ...I believe one of the options when setting up the Airport Extreme Base Station is that you can extend a wireless network already in place.
    True but the D-Link is not compatible with Apple's WDS therefore this is not possible in this situation.
    If you have a newer Airport Extreme Base Station with a USB port on it...
    FYI, every AirPort Extreme base station (AEBS) has a USB port.
    BTW, birky has indicated that he/she is using an AirPort Express (AX) not an AEBS.

  • Can't connect to Internet and 192.168.1 network at the same time

    I have been having an issue with my MacBook's networking for the past 4 months. Here are the specifics:
    *My MacBook is connected to the Internet via a linux router, with an address in the 192.168.1.x address space. DNS server is an openDns server, 208.67.222.222
    *My MacBook is assigned an IP Address manually in the 192.168.1.x namespace
    *I have a printer manually assigned an address in the 192.168.1.x namespace
    Problem:
    * I can only connect to my printer if I leave my DNS server entry blank under my Airport TCP/IP configuration
    * I can only connect to the Internet when my DNS server entry to set to the openDNS server entry.
    Question:
    Is there any way I can connect to both my local network printer and the Internet at the same time? I have set up two locations that I can switch between, but I would prefer to be able to access both networks at once.

    I tried turning AppleTalk on, but no luck.
    It seems that the problem is related to basic TCP/IP connectivity. For example, when my DNS server is set to blank, I get a fine response from the command "ping 192.168.1.253". However, when my DNS is set to one of the openDNS servers, I get this error:
    PING 192.168.1.253 (192.168.1.253): 56 data bytes
    ping: sendto: No route to host
    ping: sendto: Host is down

  • HT2731 Can we have more than one Apple ID for iTunes on the same computer

    We have a family computer.  On this computer we have an iTunes account.  My son would like to set up his own iTunes account on the same computer.  Can this be done if he creates his own Apple ID and can we use the same credit card # to set up the account?

    Welcome to the Apple Support Communities
    Of course. Just create a new user account for him, so he can have his content on another user without messing your data

  • Is it possible to have more than one event/project in Imovie at the same time?

    Let me see if I can shorten this. I am working on a project for a review. It's going to take quite awhile and I'm half way through it. However, I need to work on another project, one thats short and I can dish out fairly quickly. My problem is that I cannot start it without discarding my current project. Which I cannot do because I will lose a weeks worth of data. And I cannot save it because it will combine all the clips and I would have to re-split them (half a days progress).
    So in short, is there a way to save my project as-is? Or possible create a new event and start a new project while maintaining my current work? Thank you for your help!

    Version 10.0.3 is the latest version of iMovie. iMove '11 (as in 2011) is version 9.
    iMovie saves your Projects automatically. So you can just choose to create a new Project. Your existing Projects will remain available for you to go back to whenever you like.
    You can have as many Projects as you like. You don't need ot finish one before you begin another.
    Post back if you have specific questions.
    Matt

  • Can't connect more than one device.

    I just bought an Airport Express 2 gen from a friend and I have two issues: I tried to reset it to factory settings and could not do it. Tried holding the reset button for 10 secs, unplugging and plugging back in while holding the reset button, holding the button for a longer time and nothing worked. I had no choice but to create another network. Once created, I can't connect more than one device. If I have my MacAir hooked up the network and I try to get my Ipad in, the minute I type the network pass in my Ipad, a screen pops up where I have to log in with my internet provider account. When I do that, it will connect, but my MacAir will disconnect automatically.
    Appreciate any help!

    Things are a bit different with the 2nd Gen AirPort Express and other newer AirPorts.
    A Factory Default Reset is now the same as what was previously known as a "Hard Reset".
    Power up the AirPort Express and let it run a few minutes.
    Hold in the reset button on the Express for 10 seconds
    Release the reset button and allow a full minute for the Express to restart to a slow, blinking amber light
    If the Express is operating correctly, it will be back to factory default settings at this time.
    If you try the reset a few times and the Express will not return to default settings, the Express is defective.

  • We are a creative design studio, we need to use apple mac pro server , so we can make more than a different user to use at the same time doing different activities, on different screens, is it possible?what is the max. no. of users that can work efficient

    we are a creative design studio, we need to use apple mac pro server , so we can make more than a different user to use at the same time doing different activities, on different screens, is it possible?what is the max. no. of users that can work efficient.
    Appreciate your support and if possible , how to do this?

    If you want to work with Mac OS X, you need one computer per simultaneous user.
    What you are describing, " Multiple simultaneous logins to a single computer" is not avialable on a regular Mac of any description, unless you decide to use Unix tools instead of Mac OS X.
    Server will happily store files for many, many users and provide them to multiple (up to hundreds) of computers at "near hard Drive" speeds over Gigabit Ethernet. It can make the File Sharing part easy.

  • How can i connect more  than one database

    i would like to connect more than one database one my laptop
    now i have database one and sid=ddms
    and i would another such as sid=ddmf
    how can i connect two database on the same my laptop

    I am not sure what you mean by after built? Are you trying to export data from one database and import it into another? If so, export it using data pump making sure you have the correct ORACLE_SID. Also be sure both database have to same character set. Then change the ORACLE_SID to other database, and run data pump to import the data into the other database. Hope that makes any sense...

Maybe you are looking for