Can't connect Time Capsule via Ethernet

I recently installed Montain Lion on a new hard drive, and want to use Migration Assistant to transfer my files and settings from a Time Machine backup on at Time Capsule. In the previous version of AirPort Utility you could change how your computer connected to a Time Capsule, and one of the options was via ethernet. In Mountain Lion this option is no longer available, and when I connect via an ethernet cable my computer doesn't seem to see the drive. Anyway to do this in Mountain Lion?

I can't get the AP TC to add on to an existing network in initial set up as , even though the option is available, the Airport Utility (6.3.2) doesn't seem to keep it selected, and wants to create a new network.
"Add" would be used for a wireless connection....and you indicate that you are using Ethernet to connect the existing modem/router and Time Capsule together....so the correct setup would be to create a new network using the exact same wireless network name and password as your existing network.
Connect an Ethernet cable from one of the LAN <--> ports on the current modem/router to the WAN "O" port on the Time Capsule.
Here, I am assuming that the TC will be located at least a room or two away from your main wireless router. If it is located any closer, there will likely be wireless interference issues between the two routers. The wired connection between the modem/router and Time Capsule must be maintained.
AirPort Utility will suggest a setup that looks somewhat like this.....except you will see a Time Capsule instead of an AirPort Express as illustrated below:
Network Name would be the name of your existing wireless networik
Base Station Name is a device name that you want to call your Time Capsule
Password is the wireless password of your existing wireless network
Verify confirms that password
Click Next and the setup utility will auto configure things for you in a minute or two
When you see the message indicating Setup Complete, click Done and you should have a green light on the TC.

Similar Messages

Connect time capsule via ethernet to Mac for back-up only. Is it possible without internet connection ?

Connect time capsule via ethernet to Mac for back-up only. Is it possible without internet connection ?

Hi Bob,
I'm not certain the post I sent was posted correctly, as I added it as a reply to a 3-year old thread. Since this is a recently-active thread, though not specific to the issue at hand, I thought I'd post again:
Three years ago you helped me set up a roaming wireless network in my home. It's been rock-steady and I'm forever grateful to you for the time and guidance you gave me. I'd now like to swap out my AirPort Extreme base station for a time capsule. As I understand it, I should be able to unplug the base station and replace it with the TC without problem, so long as I use all the same settings on my TC... network name, security protocol, password, etc. Given the complexity of my network, I thought I should check with you first for any advice you might have. I don't want to set up a new network or make any changes to the existing one-- with the exception of using the TC in place of the AE. I'm already using Time Machine for backups. As a refresher, my current setup has the AE as base station and 3 expresses hard-wired with Ethernet connections elsewhere in my home. I have a 4th express set up wirelessly to use with my stereo system at the front of the house. All AXs are 'n's and are set up, as per your instructions, in Bridge mode to extend the existing network. I'm running the most updated version of Mavericks on my MBPro. Any suggestions you might have will be, as always, very much appreciated! Sincerely, Phyllis Sommers

Connecting to Time Capsule via Ethernet

Hi,
I'm working on a Tiger OS and I cannot connect to my time capsule. I followed instructions in the manual, but I simply do not see Time Capsule on my desktop, and there is very little info in the manual.
I am working off of ethernet, not airport, and would prefer to used ethernet for the moment. I have it connected via LAN port to my macbook pro. There's only one ethernet port on my computer. Does anyone have any advice? I know about about Macs, but dont have much experience with network specs.
I simply need to archive data, but I cannot see Time Capsule on my desktop. Time Capsule is connected just fine to my modem, but now how do I connect to my computer? I've tried to unplug ethernet from my computer, and into the LAN port on my capsule, but to no avail.
I am absolutely clueless as to how I can use this machine at this point??
Thanks much.

Jean,
You probably don't have the Network Preferences set correctly.
Connecting The Time Capsule Via Ethernet
Connect one end of a Cat-5 Ethernet cable into one of the LAN ports of the TC (<•••>).
Connect the other end to your Macs ethernet port.
Open Network Preferences.
At the top change "Location:" to "Ethernet Connection".
In the list on the left "Ethernet" should be at the top of the list. (If not use the Action Menu (gear button) at the bottom to "Set Service Order".)
Click "Apply" in the lower right.
Give it a moment to acquire an IP address from the TC.
You should now be connected.
Now begin your initial backup.
Now that you are reconnected to the TC, you should still have internet access during the backup.
Let us know if this was helpful. Next time start a new thread, you're more likely to get helpful responses that way.
Cheers!

Connecting Macbook with Time Capsule via Ethernet

Hello!
I have a time capsule and a macbook. I used to backup my data with the time capsule via ethernet. Now there was an update to airport I guess and since then the menue to configure the time capsule looks different and now I have trouble finding out how to set up the connection between macbook and time capsule via ethernet. I dont want the WLAN to be used so I want the ethernet be the connecting part of both esp because i want to backup lots of data now but Im missing the setting that said use use time capsule via ethernet. I just dont know how to set it up now.
I have the ethernet cable in the very left ethernet slot next to the reset button of the time capsule and its also plugged in to the ethernet slot on the macbook. But what are the settings for this connection.
Can someone help please otherwise i think my 23GB backup will take 3 days...
Thanks in advance
Dine

Open the network preferences and make sure the ethernet is getting an IP from the TC.. you do not need to change any settings .. all you need is network connection.. if the ethernet is working just turn off airport for the time the backup is going on. Once you turn off airport in the MBP the connection will be forced to ethernet. You can do it more correctly by rearranging the order of preference for network connection.. but for now.. just turn off airport.

I want to transfer files from a Win XP PC to a Mac using Time Capsule via Ethernet connection. Is this possible?

I want to transfer files from a Win XP PC to a Mac using Time Capsule via Ethernet connection. Is this possible?

Sure.. the PC connects by SMB.. the Mac connects by AFP or SMB..
But you can simply share SMB directly from the Mac.. there is no need to copy files through the TC. Go to system preference, sharing, and turn on SMB for the folder you want to share files to / from on the Mac.
Make sure you have a common username and password also helps.
If you have a TC already can you copy files to it via the windows machine??

Connecting Airport Extreme N to Time Capsule via ethernet to extend wireles

Hi, I currently have 2 Airport Extreme N and a Time capsule and would like to connect all three together. I am planning to use the time Capsule as the router and then use the other airport extreme to extend the wireless network. I am planning to have ethernet connection between the three devices ie Airport extreme N (A) is connected to time capsule via ethernet and airport extreme N (B) is connected to time capsule via another ethernet.
I have tried the Extend Wireless network option to connect them, but that seems to generate so much traffic between the airport extreme N and the time capsule that the network is not usable. I have also tried using WDS but that didn't seem to work.
The three wireless networks have some areas of overlap but the signal is weak which is why i prefer to link them up with ethernet.
What is the best wall to configure them? should I set them up so that they're each creating a wireless network but with the same name? Or is there a better solution? Thanks!

It seems to me the easiest way is to have the Airport Extreme connect to internet using Ethernet, using DHCP and the Connection sharing in off (bridge mode) and then create a new wireless network with the same name... Is that correct? I have previously ran the apple wizard and it did something weird with the network and then both the time capsule and the airport extreme are serving out IP address and both of them have the same IP address 10.0.1.1. which then messes up everything...
Any ideas? thanks!

Can't connect time capsule to imac

I can't connect Time Capsule (TC) to the iMac. I get the following message: Another device on the network is using your ocmputer's IP address.

So does the Mac get an IP from the network or is it self allocated?
Does it have internet?
Can you please give me some more info.. I want the IP of the TC.. if still default then it is 10.0.1.1
What IP has your Mac got? Just get it from the network preferences. You have direct access via the airport icon.
We have seen any number of issues with Lion and latest TC firmware. Why it works on one computer and not another I don't know.
Try rebooting all the network items.. turn everything off and start in correct order with a few minutes in between.
modem---main router (TC if that is it)----wireless extenders----then clients.
Does the TC now appear?
If not from a computer that can access it, do a reset of the TC and change all the names to SMB compliant.
Short, no spaces no special characters.. ie pure alphanumeric.
Passwords can be longer.. but same rules.. nothing more than 20 characters.
Lock the wireless channels.. for 2.4ghz, 1, 6, 11, and try each in turn if you have issues.

How can i connect/disconnect PPPoe via Ethernet connected time capsule??

I connected the time capsule with Ethernet.
I set connect to PPPoe with "Manual" option.
I could easily control "Connect/disconnect" pppoe using AIRPORT (in the menu bar). But I could not find a way to "Connect/disconnect" via ETHERNET. (No ETHERNET icon on menu bar anyway...)
Could somebody help? THanks a lot.

Have you consulted the printer's user manual for setting it up as an Ethernet printer? You will also need to delete your current printer in Print & Fax and when you Add the printer you will need to do so as an Ethernet printer. This means you will add it either as an IP printer using either LPR or IPP protocol - depends on what the printer supports. An Ethernet device requires an IP address that is either manually configured on the device or derived if the device supports DHCP. If the former then the IP address you configure for the printer must be within the range of IP addresses used by your router (typically 10.0.1.2-10.0.1.199 for an AEBS/TC.) This should be covered in the printer's user manual.

Connecting to Time Capsule via Ethernet AND wireless

I have connectivity through an Ethernet network to which my Time Capsule is connected. I connect wireless to TC, but another Mac which is out of wireless range -but still in the same Ethernet network,- cannot connect to TC via ethernet. Is there a way to have access to TC both wireless and via ethernet?
Thanks
Nilde

Hello Nadjia. Welcome to the Apple Discussions!
Is there a way to have access to TC both wireless and via ethernet?
Yes, the TC supports both wireless and Ethernet clients simultaneously. Let's double-check the Built-in Ethernet settings on the Mac that you are trying to connect via Ethernet.
System Preferences > Network > Show > Network Port Configurations
o Verify that a Built-in Ethernet option exists. If it does not, click "+" to create one. (Note: If you are unable to create a Built-in Ethernet configuration, the Ethernet card in your computer either doesn't exist or it is not recognized.)
o Verify that Built-in Ethernet is at the top of the list. If it isn't, you can drag it to the top.
Advanced > TCP/IP tab
o Configure IPv4: Using DHCP
o Configure IPv6: Off
Advanced > DNS tab
o Verify that your ISP's DNS server(s) appear. If they do not, click "+" add them.
Advanced > Proxies tab
o Configure Proxies: Manually
o Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
o Exclude simple hostnames (unchecked)
o Bypass proxy settings for these Hosts & Domains: <leave blank>
o Use Passive FTP Mode (PASV) (checked)
Ethernet tab
o Configure: Automatically

Connecting to Time Capsule via ethernet but my computer does not have an IP address

I'm connected to internet w/Airport TC.
I want to connect via ethernet for fast and stable backup. When I connect the ethernet cable what I see is "The cable for Ethernet is connected, but your computer does not have an IP address". I don't want to mess up with my connection. What should I do?

Thanks for your response Bob, I found a way to resolve my issue.
I'm connecting to internet via wireless modem. TC is connected to that wireless modem via wired ethernet connection and functions as a router - I guess - so our Apple devices connect to the network.
I had disabled WiFi earlier, since I wanted to connect to TC via ethernet. I realized I somehow needed to have the connection re-enabled WiFi but change the connection order, so ethernet is at the top of the list.
It might have been some other things I did, like trying to imitate config samples I found on the net by typing 255.255.255.0 and 192.something.something.0...etc.
Not sure exactly what made it work, but eventually, I believe I managed to connect and transfer many gigs of data over to TC with ethernet but it still took soooooo long.
Thanks,
Vanmoose

Airport Time Capsule 3TB can't connect to modem via ethernet

Hi all,
Thanks in advance for any assistance on this issue ...
I am having extreme difficulty in connecting my Airport TC to my modem via ethernet. Ideally, I want to use it to extend the range of my wifi, as well as back up my machines.
I can't get the AP TC to add on to an existing network in initial set up as , even though the option is available, the Airport Utility (6.3.2) doesn't seem to keep it selected, and wants to create a new network.
When I create the new network, my internet connection drops out, even though the modem indicates that it is connected. I then edit the internet connection in AU by telling it to extend the existing network (add in the SSID etc) which picks up the internet connection again, but then the Airport TC drops out, and all I get is a blinking amber light and a message saying no configured Airport Base Stations detected, continuing to search.
I have no doubt that it is something I am or am not doing. I have soft, hard and Factory reset the TC, reset the modem, changed cables, pretty much everything my tiny brain can think of.
I have looked through the support pages and follwed thier advice, with no luck.
Help please.

I can't get the AP TC to add on to an existing network in initial set up as , even though the option is available, the Airport Utility (6.3.2) doesn't seem to keep it selected, and wants to create a new network.
"Add" would be used for a wireless connection....and you indicate that you are using Ethernet to connect the existing modem/router and Time Capsule together....so the correct setup would be to create a new network using the exact same wireless network name and password as your existing network.
Connect an Ethernet cable from one of the LAN <--> ports on the current modem/router to the WAN "O" port on the Time Capsule.
Here, I am assuming that the TC will be located at least a room or two away from your main wireless router. If it is located any closer, there will likely be wireless interference issues between the two routers. The wired connection between the modem/router and Time Capsule must be maintained.
AirPort Utility will suggest a setup that looks somewhat like this.....except you will see a Time Capsule instead of an AirPort Express as illustrated below:
Network Name would be the name of your existing wireless networik
Base Station Name is a device name that you want to call your Time Capsule
Password is the wireless password of your existing wireless network
Verify confirms that password
Click Next and the setup utility will auto configure things for you in a minute or two
When you see the message indicating Setup Complete, click Done and you should have a green light on the TC.

Can I connect my Airport Extreme Time Capsule via ethernet to another router (non-Apple)?

I've been trying to figure this out for a few hours and have gotten nowhere. I have an Archer C7 AC1750 router set up in my office, connected to my Zoom 5341 DOCSIS 3.0 Modem; this has been my main router and has worked fine. I have moved some things around and now have my PS3 and PS4 in my master bedroom but can no longer hook them up via ethernet to the Archer C7. I have run ethernet through the attic into the master bedroom and want to use my Airport Extreme Time Capsule as a way to hook up the consoles via ethernet. If I can use the Airport Extreme to extend my wireless network back to the bedrooms that is even better, although that is an afterthought.
I am not sure what the settings need to be to make this happen. I have searched and tried a number of things but have not found a working solution.
Any help would be greatly appreciated.

Please start over with a default reset on the Time Capsule. This will not affect any of the stored data that you might have on the drive. You can use the same device name and password that you used before if you wish.
Power up the Time Capsule for a few minutes. Then hold in the reset button firmly for 10 seconds and release. Allow a full minute for the Time Capsule to restart to a slow, blinking amber light.
Make sure that the Ethernet cable connection from the Archer router connects to the WAN "O" port on the Time Capsule
Open up AirPort Utility
Click on Other WiFi Devices
Click on Time Capsule xxxxxx
AirPort Utility will suggest a setup, which you want to ignore
Instead, click the Other Options button
Select the Create a new wireless network setting and click Next
In the Network Name box, enter the exact name of your Archer wireless network
In the Base Station name box, enter a name that you want to use for the Time Capsule device
Uncheck the box to use a single password
In the Network Password box, enter the password for the Archer wireless network
Verify on the next line
In the Base Staion box, enter a password that you want to use as a device password for the Time Capsule
Verify on the next line
Click Next and wait while the AirPort Utility creates a network
Ignore the step about unplugging the modem and click Next
Do not enable the Guest Network option and click Next
Wait while the network is being set up. When you see the message that the wireless network is available, click Done
The Time Capsule will now appear in AirPort Utility with a blinking amber light
Click on the Time Capsule icon, and then click on Edit in the next small box that appears
Click the Network tab at the top of the window
Change the setting for Router Mode from DHCP and NAT to "Off (Bridge Mode)"
Click Update at the lower right and click Continue
Wait a full minute for the Time Capsule to restart and you should have a green light
It would be an excellent idea to power off both the Time Capsule and Archer router now, wait a minute, then start the Archer router and let it run a minute. Then, start the Time Capsule up and give it a minute
You should be all set. The Ethernet ports on the Time Capsule are now operable and the wireless network has been extended using AES encryption.

How can i connect macbook pro to time capsule via ethernet

I just purchased a Time Capsule to backup my MacBook Pro. I tried to back up the files via wifi but it was taking forever. I tried connecting the Time Capsule to the MacBook via an ethernet cable but it won't recognize it. Any suggestions?

When you plug in by ethernet, make sure you plug into a LAN port on the TC... ie one marked.. <...>
Make sure the connectivity led goes on.. tiny light on the port itself.
On the MBP turn off wireless.
Make sure ethernet is set to auto .. check its status in network preferences.
Finally press and hold the reset button for 10sec to reset the TC.. that usually brings them back to life if it is acting up.
What OS on the MBP?? Lion and ML have issues finding the TC.

If I connect a time capsule via ethernet to an existing internet connection and use it to create a private wifi network for my wireless devices, will other users on the primary network (not the private wifi one) be able to access my files on my TCapsule?

Like it says in the title basically.
I want to use a time capsule to store my files and backups and access it from my phone and MacBook Air. However I do not want the others in my house who are currently connected to the same wifi/ethernet router to use my connection or my TC hard drives.
I had also been thinking about wirelessly extending the wifi network (a linksys N router) but I guess that will allow everyone to access my Time Capsule?
I hope you guys can help me.
Regards, Guido

......will other users on the primary network (not the private wifi one) be able to access my files on my TCapsule?
No, if you have not provided them with the Time Capsule device password.
Users will be able to "see" the Time Capsule icon under the SHARED heading in the Finder on their Macs, but they will not be able to access the drive or the files.
I had also been thinking about wirelessly extending the wifi network (a linksys N router) but I guess that will allow everyone to access my Time Capsule?
Same answer as above.

Time Capsule via ethernet to thunderbolt-adapter is slow

It says it's going to take 7 days to move my 153GB aperture-library to my new MBA 2012. I simply copied the library-file from the Time Capsule backup to my MBA.
I've connected my my TC to my MBA via a ethernet-cable and my thunderbolt to ethernet-adapter. It should be a lot faster than WIFI, but it isn't.
What can I do to speed it up?

Hmm,
this was too quick. It works sometimes, and sometimes not. At the moment I'm running a backup that started out with 2KBytes per second. After reconnecting the TB->Eth Interface (in software, not pulling it out), speed went up to 50MBytes per second until 890Mb were backed up, now it's down to 2KB per second again. Sometimes this goes on for like 40MB, sometimes it backs up 2GByte, but always it's going down again. In parallel I can write files with 100MBytes per second to the same device via Finder.
Odd...
Best
Armin

Can't connect Time Capsule via Ethernet

Similar Messages

Maybe you are looking for