Can't connect to 192.168.1.1

Hi all! I'm having trouble getting my wireless router setup. I have a WRT54GS Ver.2 router. I seem to have misplaced the CD and I tried using the quick install but it didn't work. When I look at the network settings, my IP address is not 192.168.x.x but 99.x.x.x. I'm running XP with SP1. Any advice? Please help! Thanks a bunch! VK

check the following steps :
1)connect the computer to the router's port#1
2)connect the modem to the router's internet port
3)there shouldn't be any cables connected between the modem and the computer directly
4)reset the router for 30 seconds and do a power cycle
5)check the ip add again and if you get 192.168.1.x , try accessing the router using http://192.168.1.1

Similar Messages

Can't connect to 192.168.1.1 with WRT610N

Hi, i've been trying to add my sister's new laptop to the authorized MAC adress on the router, but i just can't get on the 192.168.1.1 administration page. When i type the adress in, the page loads for minutes, hours and even days with no result. I tired on the four computers connected to the routers but the page just loads forever and never shows.

Hi, I think I finally found the problems with not getting access to 192.168.1.1, or at least it works on my computer for now. Haven't tried it more than today, but I think this is the problem.
Turn of Linksys advisor program. Then try 192.168.1.1 It worked on my computer. The Linksys advisor loads on startup, and I think I will have the same problem again, if it starts up, so I will try to disable it in startup. I've also configured the network settings on the connection to internet protocol version 4 (TCP/IPv4) to use the following IP address of my computer (192.168.1.X), subnett 255.255.255.0 and default gateway to 192.168.1.1. Without those setting, ie obtain IP address automatically, I couldn't reach 192.168.1.1 You can manually start the Linksys advisor program afterwards, and I had no problems connecting to 192.168.1.1
I have tried every other solution mentioned on this forum, but nothing has worked for me. The most commoned answer is, reset your router or turn off the router, then it will work again. It does, but only for a day, or sometimes minutes, then its back to the same problem, with not being able to connect to 192.168.1.1 I have also downgraded the firmware and are using open DNS, but that didn't help. It seems to me that the problem is with the Linksys advisor program, kind of strange that I have read only one post mentioning that! But of course, I'm not 100% sure, but again, its working on my computer, and I can finally connect to the administration pages again!

Can't connect to 192.168.1.1 with my macbook. Tried reading all the posts no luck.

I've read through tons of posts and still no solution. I have powered everything on and off. I've tried firefox, safari, and netscape. I still cannot connect to 192.168.1.1 I have a befw11s4 v2. Along with not being able to connect to the setup page, my internet signal strength goes up and down constantly even though I am right next to the router.

If something does not work there is usually an error message which explains the problem. Please post the exact error message you get.
When wired to the router, open a terminal window and enter "ifconfig en0". Please post the output of that command.
Next enter "ping 192.168.1.1" and post what happens. Again, if there is an error message post the exact error message.

Can't connect to 192.168.1.1 EA6500 or the Internet

Hi
Yesterday my router froze and wouldn't do anything, so I rebooted the router. When it got up and running again, I couldn't connect to the Internet. I got the error 502 - bad gateway.
I can't connect to it at 192.168.1.1 or linksyssmartwifi.com. I can ping 192.168.1.1, but not 8.8.8.8.
Ipconfig /all
DHCP yes
Ip 192.168.1.117
Subnet 255.255.255.0
Default gateway 192.168.1.1
DHCP server 192.168.1.1
I've tried flushdns, release and renew and it seems that the DHCP server from the router is working.
In windows it seems that there are an Internet connection.
I don't understand this, I can't visit any websites, but Spotify works.
I'm afraid it's broken and I have to buy a new router. I've triede to reset the router.
I hope that some of you can might help me.

Try disconnecting the router from the internet (WAN port) and plugging a PC directly into one of the LAN ports. After resetting, ignore the smartwifi login, click the two checkboxes, and login manually/directly with the "admin" password and reconfigure.
If you don't want to do all that just yet, try accessing the router from the public IP address assigned by your ISP. That might work

Still can't get to 192.168.1.1

I posted this issue around July 7th and tried the advice given then--ping, tried a trace, and still unable to connect to 192.168.1.1. I tried connecting the desktop directly to the cable modem and accessing above and still no access. I tried uninstalling the router, but when I go to add/remove programs I don't see anything related to Linksys, and i tried to just reinstall by using the CD, but when I go thru the steps, the wizard states that it is unable to connect to the router. I feel like I've pretty much tried everything, including resetting the router w/the reset button, w/o success, so does this mean my router is toast? Or is it the cable modem provided by Comcast that I need to replace? I'd hate to go thru buying a new router only to have the same issue. Thanks so much for all your help! bailey

The router doesn't need to be installed, per se, so you won't see it in the control panel app. Maybe a utility program, but not the router. It may appear in device manager or in the windows registry... When you reset, do you just press and release, or hold for a minute? The latter will restore factory defaults and if not damaged will allow access to the web interface.

Why Can I not ping 192.168.2.1

I set up a G4 Mac 10.5.8 with two ethernet connections. Both with Static addressing. I have internet sharing turned on, with en0 being shared with en1
en0 is 172.20.0.75, 255.255.255.0, Router 172.20.0.1
en1 is 192.168.2.1, 255.255.255.0, Router 172.20.0.75
a laptop using 172.20.0.1 255.255.255.0 is tied to port en0
a mini using 192.168.2.75 255.255.255.0 is tied to port en1
so the schematic looks like;
(laptop 172.20.0.1) <--> (172.20.0.75 en0 - G4 - en1 192.168.2.1) <--> (192.168.2.75 mini)
from the laptop I can ping 172.20.0.1, 172.20.0.75
from the G4 I can ping 172.20.0.1, 172.20.0.75, 192.168.2.1, 192.168.2.75
from the mini I can ping 192.168.2.75, 192.168.2.1, 172.20.0.75, 172.20.0.1
but from the laptop I cannot ping 192.168.2.1 or 192.168.2.75
Any suggestions as to why?

I'm very rusty on this ... but as I recall, ARP is local to a network - so ARP info won't be passed between your two networks. I think it would work if the laptop was told to use the G4's en0 IP address as router, and the mini was told to use the G4's en1 IP address as router. The laptop, asked to ping the mini, says "not on my network" so sends it to its router (G4 en0), which knows how to deliver it. The mini, replying, says "not on my network" so sends it to its router (G4 en1), which knows how to deliver it, so you get ping & reply.
I don't think it matters that both networks are using private address space, as they are connected by a common device, the G4.

Trouble connecting to 192.168.1.1 & setting up wireless router

I am hoping someone can please help me!! I have a PowerMac G4 and a new 12" PowerBook G4. I received a Linksys router as a gift and I am having trouble setting it up...I have tried connecting to the ip address, http://192.168.1.1 with both Internet Explorer and Safari to no avail. I enter in the address and it tells me the connection has failed. I have tried numerous individuals including Linksys support and have had no luck! Can anyone help me or tell me what I may be doing wrong?
PowerMac G4 Mac OS X (10.3.1)
PowerMac G4 Mac OS X (10.3.1)
PowerMac G4 Mac OS X (10.3.1)

Lets start with some basic stuff.
First Shut your computer clear OFF.
Next pull the power adapter from your Internet
Service Providers Modem.
Next do the same thing with your New Router, Pull the
Plug on everything.
Remove any other USB items you might have connected
Printer scanner, camera.
Now you need to wait for 5 minutes.
NOW IN ORDER.
Plug the Ethernet cable from your ISP's Modem to your
Uplink port on your New Router.
Next
Plug the power adapter back in to your ISP'S Modem,
and wait until it re-aqiures the signal, depending on
the brand and who your service is with normally 3
lights.
Next after you are good on the modem you can plug in
your new Router, again wait for it to get it's signal
and lights.This will normally take a minute or so.
Now you can restart your computer.
After it boots up click on the Safari icon, and see
if it connects you.
If not go to the menu bar in your browser and type in
192.168.1.1
This should open the Linksys Utility box that will
enable you to confiqure your network.
Remember you will have to have all of the proper
setting in both your Browser and your Mail program
for everything to work properly.
Click on the Icon of Safari, and choose Preferences
this will allow you to setup
The same with Mail.
Good Luck Don
Hi, Don. Is the ethernet cable from the modem supposed to plug into the router's WAN port or the Uplink port?

Connecting to 192.168.1.1 for checking router settings online brings non-English setup?

Bought a new WRT54G vers 6 router to replace a version 3 that died on us recently, and we have had many issues with SBC Global DSL connectivity, but when I go to the 192.168.1.1 site, it isn't in English, but in Italian or Spanish..
I can guess on some issues, but I never had a choice to pick what language this router page setup area would be in. Any ideas?
I could use some help here.

You need to download the correct firmware and upgrade or use tftp.exe.

For connection to 192.168.1.1

Recently, I can not connect to the ip of 192.168.1.1. I can go into the internet. All my three computers can connect to the router via cable but only one computer can connect to it by wireless adapter. Also I can not succeed when to PING 192.168.1.1 . What is the problem? Is my router wrong with something?

Open a command prompt window and enter "ipconfig /all". Post the full output.

Cannot connect to 192.168.1.1

I did a firmware upgrade on the BEFW11S4 yesterday and now I cannot access the web utility. I've tried ipconfig /release and /renew, but to no avail. I've also tried setting a static IP but that did not work as well. I did the firmware upgrade via wireless, and it gave me a success message after it was finished, but the router somehow lagged afterwards, so I did a reset on the utility and it connected. My internet connection is working fine, but I can't ping 192.168.1.1. My ipconfig returns:
Connection-specific DNS Suffix . : nyc.rr.com
IP Address. . . . . . . . . . . . : 24.193.219.59
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 24.193.216.1
Any ideas? The default gateway should be 192.168.1.1 I've heard, but I have no idea how to set it without being able to communicate with the router.
I also did an IP scan on 192.168.0.* and 192.168.1.* and both returned all IP addresses in that range as dead.
Thanks.

Hey based on your IP check, it seems you are getting an IP address from your modem or from another device. Those IP's that you listed are actually valid IP's but they are not IP's that a private device like a router would give out.

How can I change my 192.168.1.1 settings

Hi I'm on a sim only wifi package. My Device is a Huawei e8278 in car wifi that was purchased unlocked. With my EE card in the dongle I can access the 192.168.11 management page but not all of the options that should be available are. Does EE have its own mobile broadband management software and if so how can I obtain a copy. Thanks for time your help is much appreciated.RegardsMJ

What's missing? All the functionality provided should be already on the device.

Can't connect to admin utility on WAP54G

Hi
I'm having a hard time connecting to the web-based admin utility on my WAP54G (v3.1). Even after resetting, I can't connect to 192.168.1.245.
Indeed it seems that the router isn't creating the usual masked 192.168.1.x network it usually does; when I do an ipconfig it gives the following, suggesting that it's just passing on the settings from the cable modem
Ethernet adapter Wireless Network Connection:
        Connection-specific DNS Suffix . : hsd1.ma.comcast.net.
        IP Address. . . . . . . . . . . . : 65.96.187.171
        Subnet Mask . . . . . . . . . . . : 255.255.252.0
        Default Gateway . . . . . . . . . : 65.96.184.1
Holding the reset button appears to have no effect. Anyone know what's going on here?
Thanks!
ben

The product which you have its and access point, its not an Router... And when your AP is connected to the Modem, then it will bypass its IP address and it will provide you the IP address given to you by Comcast... This way only your 1 computer will be able to go online from AP if its connected to the Comcast Modem...
To access the setup page of your AP, Hardwired the AP to the computer and assigne a Static IP to the AP i.e : 192.168.1.20, Subnet : 255.255.255.0, Default Gateway : 192.168.1.1..... Now you should be able to access the setup page of your AP...

WRT54G can''t connect to internet or 192.168.1.1

My router used to work. I updated the firmware to 4.21. xx and after that I can't connect to internet.
When I connect directly to modem, I can go to the internet . I power recycled etc but when I connect to the router, it says limited connectivity. It shows autoconfigurtion ip:169.254.251.135
I don't know why this is so.
I don't have the setup cd disk but I read the users' guide and it seems that I really don;t need the cd. But no matter what I do , I can't get to 192.168.1.1 .
Do I need a setup cd and where I can download?
Any help is appreciated.
Thanks ,
Sankar

Do the 30/30/30 Hard Reset and then check the IP address on that computer. For the reset steps do the following:
The following procedure will clear out the NVRAM and set Router back to default values:
With the unit powered on, press and hold the reset button on back of unit for 30 seconds
Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
Plug the unit back in STILL holding the reset button a final 30 seconds....
If still you are getting same IP address then try to reduce the LAN card speed. Here is the step:
START--> right-click My Network Places and click Properties
right-click on the device and click properties
Click on the CONFIGURE button
Select the ADVANCED tab and the settings you can alter are listed on the left.

Windows 7 Static IP localhost connects but Static IP 192.168.0.127 does not

This is the error:
[Fiddler] The connection to '192.168.0.127' failed.
Error: ConnectionRefused (0x274d).
System.Net.Sockets.SocketException No connection could be made because the target machine actively refused it 192.168.0.127:16020

Connection refused is most commonly due to firewall.
Disable windows firewalla s a test an if it prooves the cause re-enable it and configure the appropriate exception(s).
Also check if the might be an infrastucure firewall in place.
MCP/MCSA/MCTS/MCITP

After update I can't connect to the internet in no way, shape or form

I rarely update because: 1) something always breaks when you update (like now) and 2) I don't like to deal with new crap like GNOME 3. Anyway:
I bought a new router (TL-WR1043N) and configured it with an old Ubuntu because connecting to 192.168.1.1 didn't work on any of my Arch Linux installations. Now... here's where it all starts... I can't use the 'n' wireless on my laptop since I have to install something to use WPA, and to install that I need to update, but I don't want to deal with GNOME 3 and Firefox >3. But I gave up eventually gave up and connected my laptop to the router by Ethernet cable. Setting that up was very easy: 'ifconfig eth0 up; dhcpcd'. Voila! I updated my whole system and restarted. To see how badly I damaged my system I opened Nautilus (I use Openbox with some GNOME programs): shock and dismay, the fonts are visible from the moon. I guess I'll have to quit using GNOME programs completely now but I expected that. I used to use KDE back in the day and when KDE4 came forth from that unholy pit, I immediately abandoned it for GNOME. This time we had more time to prepare, everybody knew what GNOME 3 was going to be. I started using Openbox quite a long time ago.
Anyway: Now to fix my wireless right? WRONG! I can't connect to the internet on cable to get the packages for wireless. I installed Windows 7 64 on the same laptop and it connects to the cable. Ubuntu 9.10 Live also connects, but due to the changes of rc.conf and network stuff I can't connect at all with Arch Linux.
So I decided to abandon it completely and reinstall from scratch. But the Live CD also doesn't work. With all the ways I've tried it all comes down to this:
dhcpcd always times out waiting for a carrier and 'ip addr' shows 'eth0: <NO-CARRIER, ....' if the interface is up. I'm not sure what information I should give you, but I can't paste any here since I can't connect to the damn internet on that laptop.
About the router: the cable is plugged on port 1 and the LED for it flashes if I reboot the computer. In Windows it stops flashing while it connects and flashes again when connected. I removed 'network' from DAEMONS and it flashes till I start it with '/etc/rc.d/network start'. This hangs for a while and returns '[DONE]' even though it doesn't work and the LED never flashes again on the router.
In rc.conf I have exactly what the example says for DHCP. In any case, it doesn't work with the Live CD either.
EDIT 1: From lscpi: painstakingly typed:
06:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
07:00.0 Ethernet controller: Realtek Semiconducctor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
EDIT 2: Just to be clear: I can use the wireless on the laptop on the Live CD, but I want to use the cable because of the greater speed (94Mbit/s on cable 60 something on wireless n, 20 something on g) and because I rarely move the laptop.
EDIT 3: lspci -v shows "Kernel driver in use: r8169 / Kernel modules: r8169", so the driver is loaded.
EDIT 4: So if I boot from the CD. ip addr shows:
eth: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:1d:92:...etc... brd ff:ff:ff:ff:ff:ff
And the LED flashes. When I type: "ifconfig eth0 up" it stops, never to light up again and ip addr shows: "eth: <nO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
Last edited by imtired (2011-09-08 12:36:51)

When you're in Arch, use output redirection
lspci >lspci.out
then boot into Ubuntu or something where you can access the files and the BBS, Of course, don't forget to use a new file for each command output.
The new network config in rc.conf is not that complicated (wired anyway; never used wireless). OTOH I've had issues on two machines where I have to restart the network daemon (rc.d restart network) or rerun netcfg (netcfg eth0) after boot to get connectivity. And I still haven't come to grips with the ip command.

Can't connect to 192.168.1.1

Similar Messages

Maybe you are looking for