Can't connect to my router

i can't connect to my router at 192.168.1.1
Unfortuanletly i was stupid and changed the static ip address of the router to my computers ip address, and now i cant access the router address.
Is there anyway to fix this?
I have the wireless g router with speedbooster.
thanks

thanks cyberdoc, i managed to access the page by unplugging my router and modem, plugged in again, then typed my new address and the page appeared. i changed my address to the default again, but then had to unplug and replug the again. it seems to work that way.

Similar Messages

I can't connect to the router in my home. Things were working fine as usual - I attended school and connected to their WiFi network as usual. When I returned home I could not connect to my own home router. The Ipad seeks the network but nothing happens

I can't connect to the router in my home. The Ipad seeks the network but nothing happens. I went to school and connected to their WiFi network as usual with no problems. When I returned home I could not connect to my home router. The Ipad seeks the router number but nothing happens. I rebooted the Ipad a few times in the school. The numbers identifying the router, etc. on my Ipad no longer appear there.
TThe Ipad guide says to connect to the WiFi use setup but I can't find the setup program in the Ipad.
I reset the network settings to the factory defaults but this doesn't fix the problem.
What can I do to reconnect to my home router?

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

My mac can't connect to belkin router? My mac can connect but I still can't surf the net? Help Please... This is my first time to use mac and belkin.

My mac can't connect to belkin router? My mac can connect but I still can't surf the net? Help Please... This is my first time to use mac and belkin.

Is it Wireless you're trying to connect with?
Which Mac?
So we know more about it...
At the Apple Icon at top left>About this Mac, then click on More Info, then click on Hardware> and report this upto but not including the Serial#...
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 6 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4

After software Update (2006-07), airport can not connect to the router

Hi,
I installed the software update 2006-07. Afterwards the airport extreme can not connect to the router anymore (NETGEAR). I use a WEP key, but even if I type the WEP Key, the airport does not succeed to the router anymore... I called Apple Care and they wanted that I install the firmware restoration. But even I didn't succeed to install the firmware restoration. On the firmware restoration web page (http://www.apple.com/support/downloads/firmwarerestorationcd12.html) is written that I have to turn on the computer and continue holding down the power button until the LED blinks rapidly followed immediately by a successive series of blinks (3 quick blinks, 3 slow blinks, 3 quick blinks). But after the LED blinks, there is not the successive series of blinks...
I know there is 2 questions in one message, but could you please help?
Thanks in advance.
Best regards,
Eric
MacBook Pro Intel Core 2 Duo Mac OS X (10.4.8)

http://forums.macosxhints.com/showthread.php?p=337100
Exactly the same problems as mentioned here kernel panics, etc. How could this have passed Apple Quality Checks?
Tue Dec 5 09:26:34 2006
panic(cpu 0 caller 0x000A8800): Uncorrectable machine check: pc = 000000003931288C, msr = 0000000000149030, dsisr = 40000000, dar = 000000003A207F7E
AsyncSrc = 0000000000000000, CoreFIR = 0000000000000000
L2FIR = 0000000000000000, BusFir = 0000000000000000
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000A8800 0x000A7A90 0x000AB780
Proceeding back via exception chain:
Exception state (sv=0x39D1B780)
PC=0x3931288C; MSR=0x00149030; DAR=0x3A207F7E; DSISR=0x40000000; LR=0x39312858; R1=0x2285BA10; XCP=0x00000008 (0x200 - Machine check)
Backtrace:
0x39312848 0x393139B8 0x39333874 0x393336BC 0x393332F0 0x3933313C
0x002D124C 0x393314AC 0x39332774 0x002EB838 0x0008C6A4 0x0002921C 0x000233F8 0x000ABAAC
0x00000000
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.AppleAirPort2(405.1)@0x392f4000
dependency: com.apple.iokit.IONetworkingFamily(1.5.0)@0x386e6000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x32922000
Exception state (sv=0x39D3A780)
PC=0x9000AB48; MSR=0x0200F030; DAR=0x003B8000; DSISR=0x42000000; LR=0x9000AA9C; R1=0xBFFFCCA0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Just by enabling the airport express card. Now I wonder what triggers the bug. Because I rebooted several times after the update. One thing I did see was the signal strength going less strong in the past days. Since today I cannot use it at all.

I installed an airport card in my powermac g4, how do I connect to my router (not an airport base.) How can I connect to my router?

I have a powermac g4 quicksilver in which I have installed a normal airport wireless card in the dedicated slot. How can I connect to my router? It is not an apple airbase station but does it need to be? How can I connect to my router?

What encryption is the Rouer using? If WPA2 you likely can't.
Go to System Preferences
Click Network
Highlight AirPort and click Configure...
What shows for Routers there? Or is Join Other Network availabe in 10.3.x?

HT204409 Iphone 4s can't connected to WiFi router.

After restore Iphone 4s I can't connected to wifi router. I see around all network ,typing password,but is not connected

Try forgetting the network and starting over. If that doesn't work, reset network settings.

Can't connect to new router...

Hi
I've just installed a new intranet here at my place and one of the changes is that my computer must connect to another router now. While everything works perfect in both Knoppix and windows, I can't get Arch to connect....
I've collected all files to show you my situation (I think):
rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_GB.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Brussels"
KEYMAP="be-latin1.map.gz"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=(pcmcia)
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to blacklist it
MODULES=(ath_pci fglrx powernow-k8)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
HOSTNAME="icarus"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.123.254"
#gateway="default gw 192.168.1.1"
ROUTES=(gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network-profiles
#NET_PROFILES=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(@syslog-ng iptables @network !netfs @hal @crond !ifplugd @alsa @ddclient @denyhosts @sshd @mpd @powernowd)
# End of file
lspci -vvv section for my network card:
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Unknown device 1631:d008
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 8800 [size=256]
Region 1: Memory at ff3ef400 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 50000000 [disabled] [size=64K]
Capabilities: <access denied>
ifconfig output:
eth0 Link encap:Ethernet HWaddr 00:13:D3:8B:9E:89
inet addr:192.168.123.1 Bcast:192.168.123.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:690 (690.0 b) TX bytes:994 (994.0 b)
Interrupt:19 Base address:0x400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:68 errors:0 dropped:0 overruns:0 frame:0
TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3998 (3.9 Kb) TX bytes:3998 (3.9 Kb)
lsmod:
Module Size Used by
nls_cp437 5888 1
vfat 10880 1
fat 45852 1 vfat
cpufreq_userspace 3536 1
ipt_REJECT 3968 1
ipt_LOG 6144 8
nf_conntrack_ipv4 14092 6
xt_state 2432 6
nf_conntrack 52872 2 nf_conntrack_ipv4,xt_state
nfnetlink 4760 2 nf_conntrack_ipv4,nf_conntrack
xt_limit 2560 10
xt_tcpudp 3328 22
iptable_filter 2688 1
iptable_mangle 2560 0
ip_tables 10452 2 iptable_filter,iptable_mangle
x_tables 11908 6 ipt_REJECT,ipt_LOG,xt_state,xt_limit,xt_tcpudp,ip_tables
isofs 31040 0
zlib_inflate 16256 1 isofs
tda827x 6916 1
saa7134_dvb 15884 0
dvb_pll 12292 1 saa7134_dvb
ohci1394 31408 0
ieee1394 81720 1 ohci1394
video_buf_dvb 4996 1 saa7134_dvb
dvb_core 71976 1 video_buf_dvb
tda1004x 15492 2 saa7134_dvb
snd_seq_oss 29312 0
snd_seq_midi_event 6528 1 snd_seq_oss
snd_seq 46672 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 6924 2 snd_seq_oss,snd_seq
ppdev 7556 0
lp 9348 0
tuner 61352 0
usb_storage 79296 1
snd_pcm_oss 37024 0
snd_mixer_oss 14592 1 snd_pcm_oss
firewire_ohci 15360 0
firewire_core 36032 1 firewire_ohci
crc_itu_t 2304 1 firewire_core
pcspkr 2944 0
saa7134 119244 1 saa7134_dvb
ppp_generic 23828 0
slhc 5760 1 ppp_generic
ide_core 112580 1 usb_storage
8139cp 19584 0
8139too 23168 0
mii 4864 2 8139cp,8139too
video_buf 20356 3 saa7134_dvb,video_buf_dvb,saa7134
compat_ioctl32 1536 1 saa7134
ir_kbd_i2c 7184 1 saa7134
ir_common 30084 2 saa7134,ir_kbd_i2c
videodev 26752 1 saa7134
v4l2_common 15744 3 tuner,saa7134,videodev
v4l1_compat 14084 2 saa7134,videodev
parport_pc 35556 1
parport 31304 3 ppdev,lp,parport_pc
serio_raw 5764 0
psmouse 35984 0
snd_atiixp 15884 2
snd_ac97_codec 95652 1 snd_atiixp
ac97_bus 2432 1 snd_ac97_codec
snd_pcm 69124 4 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer 19332 3 snd_seq,snd_pcm
snd 45028 11 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
soundcore 6496 1 snd
snd_page_alloc 7816 2 snd_atiixp,snd_pcm
rtc_cmos 7328 0
rtc_core 14984 1 rtc_cmos
rtc_lib 2944 1 rtc_core
sg 26652 0
k8temp 4864 0
i2c_piix4 7948 0
i2c_core 20352 8 tda827x,saa7134_dvb,dvb_pll,tda1004x,tuner,saa7134,ir_kbd_i2c,i2c_piix4
ehci_hcd 30732 0
tsdev 6720 0
ati_agp 7308 0
ohci_hcd 19588 0
evdev 8192 4
thermal 10888 0
fan 3844 0
button 6160 0
battery 8324 0
ac 4100 0
powernow_k8 13972 0
freq_table 3984 1 powernow_k8
processor 24788 2 thermal,powernow_k8
fglrx 726624 11
agpgart 27224 2 ati_agp,fglrx
wlan_scan_sta 12416 0
ath_rate_sample 13312 1
ath_pci 104744 0
wlan 195504 4 wlan_scan_sta,ath_rate_sample,ath_pci
ath_hal 231264 3 ath_rate_sample,ath_pci
usbcore 112520 4 usb_storage,ehci_hcd,ohci_hcd
ext3 119432 3
jbd 54312 1 ext3
mbcache 6916 1 ext3
sr_mod 14756 0
cdrom 34336 1 sr_mod
sd_mod 22784 8
pata_atiixp 5888 2
sata_sil 8456 4
ata_generic 5380 0
libata 108084 3 pata_atiixp,sata_sil,ata_generic
and dmesg output after a fresh bootup:
Linux version 2.6.22-ARCH (root@workstation64) (gcc version 4.2.1) #1 SMP PREEMPT Fri Aug 31 19:54:09 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 262096) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262096
early_node_map[1] active PFN ranges
0: 0 -> 262096
On node 0 totalpages: 262096
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 255 pages used for memmap
HighMem zone: 32465 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP 000F90C0, 0014 (r0 ACPIAM)
ACPI: RSDT 3FFD0000, 0038 (r1 A M I OEMRSDT 7000520 MSFT 97)
ACPI: FACP 3FFD0200, 0084 (r2 A M I OEMFACP 7000520 MSFT 97)
ACPI: DSDT 3FFD0430, 397A (r1 0AAAA 0AAAA000 0 INTL 2002026)
ACPI: FACS 3FFDE000, 0040
ACPI: APIC 3FFD0390, 005C (r1 A M I OEMAPIC 7000520 MSFT 97)
ACPI: MCFG 3FFD03F0, 003C (r1 A M I OEMMCFG 7000520 MSFT 97)
ACPI: SSDT 3FFD3DB0, 0D6E (r1 ATI ATIPATCH 1 INTL 2002026)
ACPI: OEMB 3FFDE040, 0056 (r1 A M I AMI_OEM 7000520 MSFT 97)
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:7 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
Built 1 zonelists. Total pages: 260049
Kernel command line: root=/dev/sda1 rootfstype=ext3 ro vga=795 clock=pit
Warning! clock= boot option is deprecated. Use clocksource=xyz
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2189.023 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034320k/1048384k available (2393k kernel code, 13332k reserved, 783k data, 304k init, 130880k highmem)
virtual kernel memory layout:
fixmap : 0xfff82000 - 0xfffff000 ( 500 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0421000 - 0xc046d000 ( 304 kB)
.data : 0xc035641f - 0xc041a1bc ( 783 kB)
.text : 0xc0100000 - 0xc035641f (2393 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4382.14 BogoMIPS (lpj=7301039)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
CPU0: AMD Athlon(tm) 64 Processor 3700+ stepping 01
Total of 1 processors activated (4382.14 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
pnp: 00:08: iomem range 0xfff80000-0xffffffff could not be reserved
pnp: 00:0b: ioport range 0xe00-0xe7f has been reserved
pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x3fffffff could not be reserved
Time: pit clocksource has been installed.
PCI: Bridge: 0000:00:02.0
IO window: 7000-7fff
MEM window: ff200000-ff2fffff
PREFETCH window: bff00000-dfefffff
PCI: Bridge: 0000:00:14.4
IO window: 8000-8fff
MEM window: ff300000-ff3fffff
PREFETCH window: 50000000-500fffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 481k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [email protected]).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 7680k, total 262144k
vesafb: mode is 1280x1024x24, linelength=3840, pages=67
vesafb: protected mode interface info at c000:5977
vesafb: pmi: set display start = c00c5a0b, set palette = c00c5a57
vesafb: pmi: ports = 7810 7816 7854 7838 783c 785c 7800 7804 78b0 78b2 78b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 304k freed
libata version 2.21 loaded.
sata_sil 0000:00:11.0: version 2.2
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 16
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xf881ec80 ctl 0xf881ec8a bmdma 0xf881ec00 irq 16
ata2: SATA max UDMA/100 cmd 0xf881ecc0 ctl 0xf881ecca bmdma 0xf881ec08 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
ata1.00: 312581808 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17
scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 cmd 0xf8826880 ctl 0xf882688a bmdma 0xf8826800 irq 17
ata4: SATA max UDMA/100 cmd 0xf88268c0 ctl 0xf88268ca bmdma 0xf8826808 irq 17
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:14.1 to 64
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ff00 irq 14
ata6: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ff08 irq 15
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 > sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ata5.00: ATA-6: ST3160021A, 8.01, max UDMA/100
ata5.00: 312581808 sectors, multi 16: LBA48
ata5.00: configured for UDMA/100
ata6.00: ATAPI: _NEC DVD_RW ND-3530A, 2.01, max UDMA/33
ata6.00: configured for UDMA/33
scsi 4:0:0:0: Direct-Access ATA ST3160021A 8.01 PQ: 0 ANSI: 5
sd 4:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 4:0:0:0: [sdb] Attached SCSI disk
scsi 5:0:0:0: CD-ROM _NEC DVD_RW ND-3530A 2.01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 5:0:0:0: Attached scsi CD-ROM sr0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
wlan: 0.8.4.2 (0.9.4)
ath_pci: 0.9.4.5 (0.9.4)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 20 (level, low) -> IRQ 19
ath_pci: switching rfkill capability off
ath_rate_sample: 1.2 (0.9.4)
ath_pci: switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 7.9 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xff3f0000, irq=19
Linux agpgart interface v0.102 (c) Dave Jones
[fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[fglrx] USWC is disabled in module parameters
[fglrx] PAT is disabled!
[fglrx] module loaded - fglrx 8.40.4 [Jul 31 2007] on minor 0
ACPI: duty_cycle spans bit 4
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3700+ processors (version 2.00.00)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x6
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x8
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 20, io mem 0xff6fe000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 20, io mem 0xff6fd000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 4:0:0:0: Attached scsi generic sg1 type 0
sr 5:0:0:0: Attached scsi generic sg2 type 5
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 20
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: irq 20, io mem 0xff6fc000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
usb 3-2: new high speed USB device using ehci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
usb 2-3: new full speed USB device using ohci_hcd and address 2
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
PPP generic driver version 2.4.2
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xf913e400, 00:13:d3:8b:9e:89, IRQ 19
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
usb 2-3: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21
firewire_ohci: Added fw-ohci device 0000:02:04.0, OHCI version 1.10
ACPI: PCI Interrupt 0000:00:14.5[b] -> GSI 17 (level, low) -> IRQ 22
firewire_core: created new fw device fw0 (0 config rom retries)
input: PC Speaker as /class/input/input4
input: ImExPS/2 Logitech Wheel Mouse as /class/input/input5
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21
saa7133[0]: found at 0000:02:01.0, rev: 208, irq: 21, latency: 64, mmio: 0xff3ef800
saa7133[0]: subsystem: 1043:4857, board: ASUSTeK P7131 Dual [card=78,autodetected]
saa7133[0]: board init: gpio is 0
input: saa7134 IR (ASUSTeK P7131 Dual) as /class/input/input6
saa7133[0]: i2c eeprom 00: 43 10 57 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: 00 01 20 00 ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 cb ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 00 ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 1-004b: chip found @ 0x96 (saa7133[0])
tuner 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
tuner 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
DVB: registering new adapter (saa7133[0]).
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
scsi 6:0:0:0: Direct-Access Seagate External Drive PQ: 0 ANSI: 0
sd 6:0:0:0: [sdc] 312581808 512-byte hardware sectors (160042 MB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 27 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] 312581808 512-byte hardware sectors (160042 MB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 27 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 6:0:0:0: [sdc] Attached SCSI disk
sd 6:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
sd 7:0:0:0: [sdd] Attached SCSI removable disk
sd 7:0:0:0: Attached scsi generic sg4 type 0
scsi 7:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
sd 7:0:0:1: [sde] Attached SCSI removable disk
sd 7:0:0:1: Attached scsi generic sg5 type 0
scsi 7:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
sd 7:0:0:2: [sdf] Attached SCSI removable disk
sd 7:0:0:2: Attached scsi generic sg6 type 0
scsi 7:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
sd 7:0:0:3: [sdg] Attached SCSI removable disk
sd 7:0:0:3: Attached scsi generic sg7 type 0
usb-storage: device scan complete
tda1004x: found firmware revision 29 -- ok
EXT3 FS on sda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 522072k swap on /dev/disk/by-path/pci-0000:00:11.0-scsi-0:0:0:0-part5. Priority:-1 extents:1 across:522072k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8190 buckets, 65520 max)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Unknown InputIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:11:6b:27:96:74:08:00 SRC=192.168.123.254 DST=255.255.255.255 LEN=331 TOS=0x00 PREC=0x00 TTL=64 ID=64771 PROTO=UDP SPT=67 DPT=68 LEN=311
Unknown InputIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:11:6b:27:96:74:08:00 SRC=192.168.123.254 DST=255.255.255.255 LEN=331 TOS=0x00 PREC=0x00 TTL=64 ID=65027 PROTO=UDP SPT=67 DPT=68 LEN=311
Marking TSC unstable due to: cpufreq changes.
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48114 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48117 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Clocksource tsc unstable (delta = -90943342 ns)
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
My router's IP is 192.168.123.254 but if I ping that address or I try to connect to the web interface on that address to configure the router I can't get any connection... I've also tried to specify all paramaters directly in rc.conf (eth0="eth0 192.168.123.1 netmask 255.255.255.0 broadcast 192.168.123.255") but that didn't help neither.
I'm kind of out of ideas on how to solve this... I hope someone here will help me getting out of windows (the only OS on my pc with internet FTM).

I'm so stupid... I should've thought about iptables... I'm reconfiguring them now, thank you very much!

Can't connect to Netgear router with WPA enabled (MBP)

I just received a Macbook pro today, everything is wonderful except wireless networking. When it first started up, it detected my wireless network, showed me the SSID, and asked for a password. I entered the password, and it failed to connect. I decided to try later and did the rest of the install.
I connected via cabled ethernet and downloaded all of the updates. For a machine that shipped from the Apple store (custom config) a few days ago, I was surprised at having 13 LARGE updates to download. Grabbed them all, including a Firmware update which required two reboots. One for everything else, and another for the firmware.
I tried again from sysprefs, and asked for the diagnostics. It asks me for my WEP key, and there is no option for WPA. I tried entered the WPA key anyway, despite only three WEP options showing up, and it still fails.
Going through the Airport 'tab' and editing the connection, I get an option for WPA Personal, Enterprise, WPA 2 Personal, and WPA2 Enterprise as well.
I tried using WPA Personal and WPA 2 Personal and entering the key which works on other notebooks, still no joy.

Which Netgear router do you have? I use the Netgear
RangeMax WPN824 and works well with WPA enabled but I
think it may have failed to work the first time.
WGT624 v2. Works fine with other wireless devices from a number of vendors, and is detected by the Mac, but I can't connect. I don't want to disable WPA if I can help it, I have a number of other systems configured for it as is, plus guests that come to visit.
but some how I had to delete the connection,
let airport find it again and re-enter the password
to get it to work. One of those things I kind of did
in the process of troubleshooting and can't remember
exactly how it was I did it
I'll try that and see if it helps. Thanks for following up.
UPDATE: Sure enough, I deleted the network and added it back in by manually specifying the SSID and password, and it works now. No idea why, but there it is... thank you very much.

IdeaPad S205 Operating System:Windows 7 Home Premium can't connect to wifi router

Hi I have set up laptops at home before,
the brand new lenovo ideapad tells me "connections are available" and i can see my wifi has 3 bars - all good
however after enering the the network security key and click ok
it says connecting then a second later it says,
windows was unable to connect
i have tried all the recommended advice rebooted the router and the laptop and updated the driver software, however i am unsure if it was ythe most current or if in fact it did anything...
what else can i do?

Richiebee,
Do you have other PCs connected to this router and are they running Windows 7? What brand and model of router?
If you take your S205 to another location - a coffee shop, etc, are you able to connect wirelessly there? Perhaps we can try to narrow down the possibilities a bit?
Thanks!
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Can I connect another Linksys router to my current Linksys router?

Hello everybody,
I have 3 computers in my house. One computer which is used by my brother and he downloads a ton of porn, music, and opens a lot of ports for online gaming. Needless to say he is a very high risk user. I would like to isolate his computer from mine and my sisters.
Can I use two seperate routers? One router which he connects to and my sister and I connect to the other router. Will this prevent any possible file sharing between my computer and my brothers? Is this a safe way to isolate my computer from his? Please let me know how I can do this. Thanks a lot!!!

yes it is possible.
Here's what you do:
1. connect your computer to the new router (your router) to the regular port/s 1,2,3,4.
2. Access the set up page of the router (at this point there is no internet connection)>> click start, click run typed in the run field http://192.168.1.1 and enter
3. Leave the username blank and password is admin for the router (unless you changed it)
4. On the set up page>>> you'll see there local ip address on boxes 192.168.1.1>> change it to 192.168.2.1, then save settings and power cycle your router.
5. Connect now your router to his router>> to do this, run a cable from the regular port of his router to the "internet or WAN port" on your router. Reboot your computer and your router.
** on this way his computer should not be able to talk to your computers coz of the different IP address range**

My roommates computers can't connect to the router!

Hey, so I've got this Cisco Lynksys E1200 and I've got internet going to it. When I first tried to connect to it my computor automaticaly set it up (giving the network a name, changing it from tehdefault "Cisco67809" to my perfered natwork name, etc.). The problem is that my rommates laptops cant seem to connect to it properly. I know their internet cards work because they have been able to access the internet via other nearby networks on occasion.
On the 2nd computor it skips the usual..."Conecting to network" attempt and instead just says it cant connect, but its so quick to say that it cant connect that it doesn't even seem to be trying, no request for password or anything! Yet we know the computor does try to connect to other networks, so why would it be so quick to deny a connection with our network without even telling us its "trying to connect"? It then gives the options to "diagnose the problem" or "connect to another network" but the diagnose function just says it can't do anything and gives no information about whats going on.
With the 3rd computor it does connect, or so it says "conected" but with "Limited Acess" and absolutly no accesss to actual internet content.
I have tried to fully reset the router multiple times, creating brand new networks, but the same issue continues to happen. I thought it might have decided my computor was the only one allowed to access it because on each reset I was using my computor to set up the network, but when I reset it and tried to have my roomate on computor #2 set up the router and network (aka change it fromdefault Cisco67809 to our own in house network) it did not allow him to set up the network from scratch as I had done twice.
Why is this router rejecting computors and what can be done to get them online? When I log in to the routers settings it says it is set to allow up to 50 users. So far we have my laptop, and Ipad, and an I touch conneted successfully. Why cant we get the two other laptops on it?

Hi,
Can you try to clear or remove the Wireless Network Profile from those computers that can't connect? Then, try to reconnect afterwards. Probably, those old profiles stored on other computer have different wireless settings. On the E1200, make sure that MAC address filtering and Parental Control are disabled. Access your router's setup page then go to Wireless > Wireless MAC Filter > then check if it's Disabled. For Parental Control, you can access it via Access Policy tab.
Hope this helps.
If everyone needs to believe in something, I believe I'll have another beer..

Moved my laptop and now I can't connect to the router

I'm a novice at this - but that didn't stop me from setting up a wireless network - it was very easy, everything went fine and was working great for months. I took the laptop out of the house and used it at another location. When I brought the laptop home again it asked for a password - which do I use the passphrase or Key 1? Should I expect this to happen everytime I mobilize the laptop? My router is WRT54G. Thanks!

Connect to your router with a cable and name your network different. "linksys" is the default network name of a Linksys wireless router. Anyone you buys a Linksys router and just plugs it without changing it ends up with it. Maybe another neighbor bought a Linksys router as well. Thus, always rename the network name to something unique so that you can be sure that you connect to your network and not to somebody else's. Because the problem is: when your computer searches for wireless networks it only checks the name of the network. It does not show whether there is only one access point with that name or several. It could be a roaming network where several access points must have the same name or it could be just accident like several people running routers with the default name. Therefore: connect to your router with a cable, open http://192.168.1.1/ and reconfigure the wireless network name (SSID) on the wireless tab to something else. Connect to that network...

Can't connect wirelessly to router

I got a new laptop and a new router wrt160n v3 everything was going fine, my connection wirelessly was laggy but that was okay. One day by mistake i set myself as an "intruder" on my router and deleted myself off the map. I tried everything, putting the cd and reset the settings but no matter how hard i can't connect wirelessly to my router anymore. Now i have to stick a wire to my router and sit beside my computer. also when i do connect to it, it says that i cant or something. I need help asap !
question : how can i connect wirelessly back to my router

This is certainly an unusual problem, but from your description, I would have to assume that the router memorized the MAC address of your wireless adapter, and won't let you reconnect.
The best solution would be to download and install (or re-install) the lastest firmware for your router, then reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it --- you must setup the router from scratch.
Alternatively, you might be able to change the MAC address of your wireless adapter. The downside of this solution is that if you ever re-install your computer, you will need to remember to change the wireless adapter's MAC address again.
Message Edited by toomanydonuts on 01-17-2010 12:10 AM

Skype can't connect - most likely router problem, ...

Lately I can't connect to Skype at home. I've tried a lot of different solutions but none of them work.
The problem started a few months ago when I just couldn't sign into Skype (can't connect). At that time I had no change in any network settings on my computer nor my router. Interestingly enough, I could connect to Skype on Ubuntu (I have dualboot). Though even Ubuntu eventually failed to connect back then (just can't sign in) - still no changes in my network. I couldn't be bothered at the time with the problem so I just didn't use Skype.
However after some time (some weeks or a month or two), when I tried to connect to Skype again, it worked (on Win 7 as well as Ubuntu). Again, no changes to my network have been done in the mean time (Skype might of been updated, but I doubt it was on both platforms at the same time).
So Skype worked for a while until about a month ago, when the problem reoccurred. This time I said I'm going to get to the bottom of this so here is the situation:
I can connect to Skype at work no problem (on my desktop as well as my Android phone)
I can't connect to Skype at home (just won't sign in) on my desktop nor my phone
I have tried:
Reinstalling Skype with cleaning everything that Skype might have left behind
Installing an (a bit) older version 6.9 (because even the latest 6.11 didn't work). Though these two attempts I've come to see are in vain once I figured out that I can't connect to Skype on my phone as well.
Resetted my router a couple of times.
Reset my router settings to default.
Opened/forwarded Skype ports to my (local) IP. I even enabled DMZ to redirected all traffic to my desktop computer (although I'm not 100% sure that that worked as I imagine it should work).
Tried some proxy settings in Skype (Connection options) I found on your forum.
None of the above worked in any way...
My router is a TP-Link TL-WR1043ND with (I think the latest) firmware version 3.13.13 Build 130428 Rel.58290n (hardware is v1).
TLDR:
I can't sign in to Skype at home. It works when I'm at work. I can connect to Skype on my phone if I'm at work (over WiFi) or if I'm on 3G, but not if I'm on my home WiFi. That said, no software firewall can be the problem here, but my router. However I have no more ideas as to what else I can try. This forum is my last hope for finding a solution.
Please help.
Solved!
Go to Solution.

I do not know the makeup of Skype's internal security policies when it comes to this as they are not too open about this. Most companies are not. These are the only reasons I believe a block would occur based off any company's security policy.
1. A proactive measure - A blacklist of IPs is constantly obtained/updated to include anonymizer services that might harm the network.
2. An active/counteractive measure -
I. Someone uses an anonymizer to SPAM people on the Skype network:
a. Users complain using the abuse option. Users get the IP Auto-banned.
b. The company (Skype) receives the complaints or notices a trend and Manual/Auto bans the IP.
II. Too many people (connections) sign on with the same IP (due to an exit relay/proxy). Due to this being very suspicious, (maybe even DDos-like behavior) the IP is Auto-banned.
I tend to lean more towards the counteractive measure since I don't believe many proactive measures are needed to limit abuse. There is always at least one rotten apple that engages in illegal activity using anonymizers, proxies, etc. that ruin it for everybody. In reality I believe it is a combination/balance of the two. Not to be prejudice against anonymizers, just blacklists to protect the network from known attacks. For whatever reason once the threshold is met, the IP is banned. If I had to guess how long it would be in intervals of 30 days (30, 60, 90, 120, etc.). The whole Internet is not going to banned so the security policies in effect can't be too strict. It's goal is probably just to limit the majority of bad behavior that causes problems for their customers.
Skype is not the only service that reacts this way. Even ISPs will receive notices and in turn will send notices to their customer that since illegal activity (RIAA notices, etc.) is occurring due to a Tor exit relay or some other anonymizer, the ISP will terminate services with that customer if they don't cease (due to breach of contract).
I don't know whether you can limit an exit relay so it can't be used to access Skype. It may be a lost cause. If I made the choice to run a similar service it would be with a whitelist of people I knew who wouldn't use it to perform illegal activity, just remain anonymous when online.
You shouldn't have any issues running a non exit relay since in doing so your IP is not being broadcast all over the Internet like a calling card which an exit relay does. Changing your modem's MAC address is something you need to call your ISP for. However changing your router's MAC address generally does not require that. All that is required is a reboot of the modem, router, and possibly computer if you run into issues. You will probably continue to run into the same problem as long as you attempt to run an exit relay.
Be aware that for every IP that get's banned on your ISP is another IP a person could get issued for 24 hours to a week + after it gets released. Some people then visit this community and complain how they can't connect when it worked not too long ago and how Skype "sucks". So sometimes things like this create a ripple effect for other customers.

Laptop HP 1000 pavilion can not connect to a router.

Hello everybody! I got a problem with my laptop . It will connects with a router. But the Internet is not working ... I mean I can't see any website , yahoo or anything like that. It just happens about 2 days ago. Can anyone please help me ? Thank you so much .

kookinrice wrote:
Hello everybody! I got a problem with my laptop . It will connects with a router. But the Internet is not working ... I mean I can't see any website , yahoo or anything like that. It just happens about 2 days ago. Can anyone please help me ? Thank you so much .
Hi,
It could be a DNS issue. Do you have a Skype or any IM account? Have a check of the IP settings.
http://start.localnet.com/help.php?id=3
Another reason could be a system firewall or your router is not connected to the ISP. It means that you are connected to your home network but there is no connection from your ISP. Go to the router settings (type in a web browser http://192.168.1.254 or http://192.168.1.1) and have a look if the router is connected to the ISP (your internet service provider). In case that you have an IM account or Skype run it and see if you can connect to the server (online). If yes, it's definitely a DNS issue.
Dv6-7000 /Full HD/Core i5-3360M/GF 650M/Corsair 8GB/Intel 7260AC/Samsung Pro 256GB
Testing - HP 15-p000
HP Touchpad provided by HP
Currently on Debian Wheeze
*Please, help other users with the same issue by marking your solved topics as "Accept as Solution"*

Can't connect to my router

Similar Messages

Maybe you are looking for