Can't connect to network with Airport Extreme

I have just purchased and installed an Airport Extreme card (firmware version 405.1) into my eMac (with ATI graphics). The card appears in System Profiler, and I have attached the antenna wire. However, it cannot see my network (the only network in range). My iPhone can see the network when it is in the same location (as can a few Windows devices).
I have tried turning off encyption, to no avail. I believe my router is broadcasting on a frequency my card can recieve.
I have also tried resetting my SystemConfiguration folder. What else should I try?

Thanks again for the suggestions.
I had tried the router on 1 and 6, just tried it on 11 as well. No joy.
It is broadcasting the SSID.
MAC filtering isn't on.
...and then I put it back to channel 1, and now it's working!
It's working now, and there doesn't seem to be any settings that are different to when I started.
The signal is increadibly low though. When I put the access point antenna literally in the drivebay, I get three bars (out of four). A meter away I get 2 or 1 and everything times out.
It appears that something is wrong with the antenna wire, or the connection to it. This was probably an important factor all along.

Similar Messages

Can't connect to MacBook with Airport Extreme

I just swapped Airport Extreme base with new Airport Extreme 8012.N and now my Macbook can't connect to internet, keeps cutting out and dropping off. I have an iMac G5 connected via ethernet to Airport Extreme and Macbook in living room. It was working fine with old Airport Extreme router. I also have an Apple Express (not new 8012.N ) but it just blinks orange when plugged in. Any help would be appreciated.

You have to power down everything to start with. Make a clean slate so to speak.
I switched from an older Air Port Express to the new Extreme. Run the new software and when you power back up the new base station should show in the window. Follow the steps. It made me feel stupid the 1st time through and I had to do it again. You have to take your bent paperclip and reset.
After I got the new base station up and running I took the old Express and used it for Airtunes. At first it just blinked and wouldn't show up on the list of devices. I had to do the paperclip thing. And there it was! Green light! Follow the steps for Airtunes. Then I had to reconfigure my settings for my HP 3300 series wireless printer. That wasn't so bad, it all worked.
The machines all work well; we all just need pay close attention to the instructions.
I think that the Apple on line instructions could be a bit more clear. It all worked as it was supposed to but it was certainly a trial and error process.

Can I use my iPad with airport extreme to retrieve files from a USB connected hard drive?

Can I use my iPad with airport extreme to retrieve files from a USB connected hard drive?

Yes, I believe so. Please check out the NetPortal app. I don't have an iPad, but I use it on my iPod Touch to access files on my Time Capsule. It is available from the iTunes App Store.

HT4972 can't connect to network with linksys e2500

Can't connect to network with linksys E2500. Can anyone help me?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Can't connect to internet via AirPort Extreme with Laptop running Vista

I've seen a lot of posts on this topic, and maybe I'm just out of luck, but anyway...
My PC running XP can connect to the internet through the AirPort Extreme, but laptop will not. I load the AirPort Utility on the laptop. Should I be able to see the base when I run the Utility? It does not see it. I can see the wireless network with excellent strength, but all I can do.
If I can't get this to work, I'm going to just return it and to back to the wireless router. I was enticed by the ability to connect the printer and external hard drive to the base. I would like to get rid of the PC and just use my laptop for everything.

Looking over your original post again, I think I might have misunderstood you the first time. If I understand you correctly, your Vista laptop can see the wireless network and connect to it (so you have access to the Internet), but you cannot see the Airport Extreme Base Station when using Airport Utility.
If your Internet connectivity is not an issue and it's just that you can't see the base station in Airport Utility to configure it, try using an ethernet cable to connect your Vista laptop to one of the LAN ports and see if the base station shows up in Airport Utility then.

Can't Connect to Internet using AirPort Extreme Card and DLink Router

I have tried just about everything, but I can't seem to connect my MAC OS X 10.3.9 to the internet. I am using the Airport Extreme Card and no networks show up. I am trying to connect to my DLink router. I was told by DLink that it is compatible with AirPort Extreme cards, but the guys at Best Buy were unable to connect to their wireless routers, other than their Mac Router. Please let me know if you have a solution! Thanks

dannabee, Welcome to the discussion area!
What Mac do you have?
Do you have iMac G5 or a Power Mac G5?
Did you install the AirPort Extreme card yourself?

Extend existing network with Airport extreme and 3 airport express.

I want to extend an existing network (thomson TG787v) with an airport extreme (MD031Z/A) with 3 or 4 airport express(MC14Z/A)
The thomson is the router from the provider and must be used. The building is an old mansion with a lot of brick walls
I tried to connect the extreme with an ethernet cable (in bridge mode) and then connect the airport express in a line to have wifi in all rooms of the mansion.
But somehow the airport extremes cannot extend the network.
Can anyone tell me how to setup the apple devices to make this work?
Thanks
Bernhard

I tried to connect the extreme with an ethernet cable (in bridge mode)
This is the correct.
and then connect the airport express in a line to have wifi in all rooms of the mansion.
Apple's "extend a wireless network" feature will only allow you to "extend" the signal one time. So, the first Express would connect to the AirPort Extreme wirelessly and extend the signal.
But, you cannot "extend" the signal a second or third time. Each AirPort Express must be located so that it connects directly to the AirPort Extreme. In other words, each AirPort Express must be located about the same distance from the AirPort Extreme.
Another way of thinking about his is to visualize the hub and spokes of a wheel. The AirPort Extreme would be located at the "hub". Each AirPort Express would be located at then end of a "spoke". As such, each AirPort Express communicates directly to the AirPort Extreme.....not to another AirPort Express at the end of another hub.
You may need to consider installing Ethernet cable to each location where you will need an AirPort Express and configure the network that way. Performance wise, this is a much better way to "extend" the network.

Roaming network with AirPort Extreme and Netgear R6300

Hi there everyone
I need to know if I can make a roaming network with my apple AirPort Extreme as the base station and then I want to use an Ethernet cable to connect to a Netgear R6300 which will be located at the other end of my house where th connection is poor via wireless.
So is this possible with this set up and if so how do I go about configuring each router to make it work?
Will I need to make both SSIDs the same so I wan wander through the house and stay connected to the same network?

Do not even bother to link wirelessly.. Apple do not allow it.. nor probably does the netgear.. there is no proper standard to wireless link routers.. it is a case where everyone does what is right in their own eyes.
Roaming is the best anyway..
SSID = Wireless Name must be the same.. and use short, no spaces and pure alphanumeric names.. not apple type. You can set a different name for 5ghz.. imho that is the best idea.. but up to you .. roaming and band swapping at the same time leads to chaos.
WPA2 Personal = WPA2 AES security and is the only standard that should be used now..
Password for wireless the same. 10-20 character mix upper and lower case + numbers.. keep it pure alphanumeric.
And now the tricky one.. channels.. there is only one difference between the different wireless stations and that is channels. You can leave everything at auto.. but if it leads to trouble fix them on both 2.4ghz and 5ghz.
Use non-overlapping .. see
http://en.wikipedia.org/wiki/List_of_WLAN_channels
Which show the 2.4ghz channels very clearly.. you will need to work your way around the 5ghz a bit because it differs so much region to region.

Can't connect wireless device to airport extreme

I bought airport extreme router second hand and am connecting it to HP desktop windows 8. All software is installed properly and router is connected. I have a solid green light, and internet access on desktop, but cannot connect wireless devices to network (kindle, cell phone, etc.) All wireless devices show excellent network signal strength, allow me to put the password in, but all show connected and have not internet access.

This appears to be a simple modem, so assuming that you reset the modem completely before you connected it to the AirPort Extreme, the next step would be to check to insure that the AirPort is in router mode and not bridge mode.
Open up AirPort Utility, click on the AirPort Extreme, and then click Manual Setup
Click the Internet icon at the top of the window
Click the Internet Connection tab just below that
Make sure that the setting for Connection Sharing is set to Share a public IP address
Click Update to save any changes, and give the AirPort a full minute to restart
Check the network again to see if devices can connect now.

Is it possible to set up a network with airport extreme that is not on the internet

Is it possible to set up a home network using airport extreme that will be a non-internet option? Not connected to the internet wifi.

Is it possible to set up a home network using airport extreme that will be a non-internet option?
Yes
Not connected to the internet wifi.
If the AirPort Exteme is not connected to the Internet, then Internet connections will not be available on wireless or wired connections.

Time Capsule connectivity drops on extended network with Airport Extreme

I have a new Airport Extreme router as the main router in my network and a Time Capsule set to extend the 2.4Ghz network. The routers must be configured in this order because I want the 5Ghz network from the Extreme to cover my main seating area.
The problem I have is that while I'm connected to the Extreme, on either the 2.4Ghz or 5Ghz network, the connection to the Time Capsule will 'drop'. The network drive within the Time Capsule will no longer be available and the AirPort Utility no longer shows the Time Capsule. If I reboot the Extreme, the Time Capsule will reappear.
Also, when the connection drops, if I were to move within the primary range of the Time Capsult and connect to the 2.4Ghz network, it will connect flawlessly and I would have access to the Time Capsule and it's resources. It is only access through to the Time Capsule through the Extreme that is no longer available.
Any ideas what could be causing this? Both routers work flawlessly otherwise. I'm fairly certain there isn't a hardware problem here. I've gone through all the configuration settings multiple times and can't find anything that could affect this. I have the latest firmware for both routers and the latest AirPort utility.
One thing to note is that the Time Capsule is a North American unit, while the Extreme is from Hong Kong. I know there are slight differences regarding the wireless channels that both can use, but I don't think this is an issue since the Time Capsule maintains proper internet connectivity the whole time. If it was a channel issue, I'd expect the Time Capsule to lose internet access when this issue arrises.
Any suggestions are greatly appreciated!

7.4.2 firmware does NOT resolve this problem.
I also have this problem -- it started about 2 weeks ago (around July 20?), possibly at the time the new Airport Extreme firmware went into effect. I have two separate Mac laptops that each use Time Machine to back up to different disks that are attached to the Airport Extreme (i.e., each laptop has its own backup-destination disk). Both were working flawlessly before (for more than 6 months); now, each one reliably drops the connection to the disk (produces an error message, and thereafter cannot re-connect to the destination disk until I cycle the Airport Extreme with power-off/on). I had hoped that 10.5.8 would help (the release notes talked about improved stability with Airport connections), but not so.

Windows Vista can't log onto wifi network with Airport Extreme

Several problems with our network. 1. My sister's new Gateway laptop sees the network I set up from my Mac using my airport extreme, but cannot log on to it even when I removed password/encryption - even when I entered 4.2.2.1 and 4.2.2.2 in my DNS server fields. 2. the reason I even did the above is because although my Mac (Titanium G4 Powerbook previously running 10.2.8) could get on the network through the airport, I could not get to any site Google related until I read about the DNS entries as a work around. Yes the work around works but what's the real problem/fix? Regarding probem 1., some advice I'd gotten was to update the firmware on my base station as it might be a compatability issue with that and Vista. I begrudgingly upgraded to Tiger 10.4.6 then downloaded the patch to 10.4.10 (where I am now) which did lead me to an upgrade for my airport (5.3 to 5.6 now). Still, Windows cannot get on to the unsecure network!! What the heck do I need to do?!

I hope I may have found how to make the vista machines get to your Time Capsule. On the vista system go to network and sharing center. Then click on status, then you will see a window pop up with wireless network info. Click on Wireless properties and then click the advance tab at the bottom, a box without a check mark needs to be checked which says "connect if not broadcasting". I hope I got that right...try it, it's seemed to help for today at least.

Can I extend Time Capsule network with Airport Extreme

I have a new 2TB TimeCapsule, I would like to extend my network to the front of my house via Ethernet and an Airport Extreme basestation. The wireless reception in the front room is almost non existant, but I do have an Ethernet cable from the existing TimeCapsule connected to my iMac in the front room. I would like to add the old Airport Extreme Base Station to the front room and connect the Ethernet to the Wan port of the AEB and then connect the iMac and my Apple TV to the Ethernet port on the AEB.
I cannot connect via Airport Wireless due to metal studs, Cement block walls.
Is this possible?
Thanks

Is this possible?
Yes. This type of configuration is called a "roaming network"
Apple's instructions for this type of setup are here:
http://support.apple.com/kb/HT4260

How to configure home network with Airport Extreme + D-Link DIR-665

*hello everyone,*
*I had these two working fine together until the D-Link took a dump the other day. No explanation. Just stopped working until I reconfigured everything.*
*Which then led to my Airport Extreme being unable to connect to the network at all, much less the internet...*
*My home network is set up like this:*
*Optimum Cable*
*Motorola Surfboard modem --> D-Link DIR-655 (via ethernet)*
*- Provides wifi and ethernet connections on one side of my house*
*DIR-655 --> Airport Extreme (via ethernet run to other side of house)*
*- Provides wifi and ethernet connections on the other side of my house*
*My MBP won't connect to anything other than my AE running N, so I have that set up primarily for my MBP over wifi, while feeding an ethernet connection to a Netgear router running B/G, for my iPhone and other devices.*
**So here are the relative details:**
*I decided to start fresh and do a factory default configuration with my Airport Extreme. My working system from earlier was essentially it's own wifi network, but the airport utility 'insists' that I need to run my AE in bridge mode. I've tried that, but I can't get online. I can see my shared connections, so something's getting through, but I cannot connect to them, in addition to being unable to get online.*
*I'm not really sure how to best illustrate this problem, so I've ran through the process again and jotted down a few notes. Excuse the rambling nature of my narrative, this is a 'blow by blow' account of the Airport Utility setup process:*
Airport version 7.4.2
IP address 192.168.0.192
router address: 192.168.0.2
Configuring over Airport connection.
- I want AE to join my current network
-.. connect AE to my network using ethernet to extend or create second network
- select device AE will connect to using ethernet - DIR-655 network (displayed w/ airport icon?)
- create an additional network (through ethernet)
AE updates..
- problem 1 of 1 : unsecured wireless network
wpa wpa2
Bridge mode or share a single IP address using DHCP
selected bridge mode
results: AE has green light, airport utility is satisfied but no connection to network is possible. Shared connections are visible, but unable to access
next try:
manual setup
Wireless mode: create wireless network
radio mode: 802.11n only (5 GHz)
channel: auto
wireless security: WPA2 personal
(bridge mode still active)
(this is the exact setup that worked for years before..)
updated…
AE light is green, but no connection to internet or shared connections (though visible)
back to airport utility
manual setup:
internet menu:
connection sharing: share a public IP address
update
--> 2 problems
DHCP Beginning address: 192.168.0.2
DHCP Ending Address: 192.168.0.2
chose 'assist me'
(now one shared connection to Mac Mini becomes active? Had selected it earlier. Able to browse folders, but not share screen)
AE refreshed now with amber light, with reported problems
Problem 1 of 2: Internet Connection
Your Apple Wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network… etc
- changed IP address to match router IP address (?) Utility goes on to next problem
Problem 2 of 2: Conflicting DHCP Range
This Apple wireless device rejected a DHCP address in the same subnet as its internal DHCP server. You should probably switch your Apple wireless device to be in bridge mode. If you still want to be using DHCP and NAT to share a single IP address, you should change your DHCP range.
- maintain selection: share a single IP address using DHCP and NAT (utility forces you to: ignore; skip; or select bridge mode - which doesn't work..)
- chose 'skip' for problem 2
- updated AE..
New problem:
Problem 1 of 1: Double NAT
This Apple wireless device has a private IP address on its Ethernet WAN port. It is connected to a device or network that is using Network Address Translation (NAT) to provide private IP addresses. you should change you Apple wireless device from using DHCP and NAT to bridge mode.
- selected Bridge Mode
updated AE…
"Setup Complete!"
Unable to connect.
** At this point, I am still able to see my shared connections, and while iTunes is open, I can play my shared library that is on my Mac Pro, which connected to the DIR-665 via ethernet, through yet another D-Link router (DIR-615)! I am still connected to the Airport Extreme via wireless, so the system is working, to an extent.*
*So I'm not sure what to do. How can I remedy my IP address issue? Bridge mode doesn't work (as far as I've experienced), so I'm struggling with my DHCP settings..*
*Thanks to anyone who has any suggestions!*

Hi Preston,
I would recommend not starting the numbering scheme for the IP addresses using a '0'. Yes the range is 0-255, but some numbers are reserved, and not generally good practice.
Also, assuming you have reset all factory defaults, start anew and have the modem --> router using NAT for dynamic IP addresses --> (other side of the house) Airport Extreme --> not a NAT configuration, but you need a simple switch. Do not use the NAT capabilities on this one. Maybe, just maybe the computer will work now. This will eliminate your double NAT and also help (hopefully) with the D-Link.
Sorry I cannot help more, I do not own any of the products you talk about, however I have networking experience. Hope it helps.
--Morris

Can't connect to wi-fi - Airport Extreme

I can't connect my touch 2nd gen to my AE base station any more. Worked fine until the last update to AE (note to self: when wireless is working, DO NOT update, doesn't make things faster and often breaks things /note to self) but nothing now. Have several Macs connecting no prob.
I reset the Network Settings. I don't have any security on the Guest Network. I reset the passwords. I turned it on and off. It can "see" the networks. But it either just says "Cannot connect to Blah network" (one without password) or it says "Password incorrect" (one with password) - but it is.
If two Macs running 10.6.8 and one running 10.4.11 can connect with no issues, why can't the touch?
thx

Depending on how well the Cisco router and an Apple device work together, it might or might not be possible to extend your network wirelessly, but it should work to extend your network over an Ethernet connection.
An AirPort Extreme and an AirPort Express have different advantages. An Express can play music through an external amplifier and share a printer. It's also cheaper. However, it can't share disk drives. An Extreme can share printers and disk drives, but can't stream music. It's also more expensive.

Can't connect to network with Airport Extreme

Similar Messages

Maybe you are looking for