Can't connect to PSN. Error code: ce-33987-0

Almost every night I can't connect to PSN. Error code: ce-33987-0
After multiple PS4 restarts and my router restarts - it connects. Sometimes it connects after few hours without doing anything at all. So I couldn't find any pattern.
My router and internet is perfect - all other devices at home has perfect internet connection at full speed.
I tried all the tricks I've found in this forum (make my PS4 primary, connect to wifi and connect back to cable, do not turn off PS4 and leave in standby, check NAT type etc.).
But nothing helped.
Connection test shows NAT Type 2 which is perfectly OK I guess.
Is this PSN that unstable or what?
How should I solve this problem?

I've been having the same problem for over a week, but I think I found the solution to it.Firstly, my internet setup is an old netgear modem-router combo hooked up to a new TP-Link (n) router. The netgear is set to modem only mode. My ps4 is connected wirelessly downstairs.For about 3 months, my ps4 was working normally with no problems, but about a week ago this error code started popping up inconsistently. Sometimes everything was fine, most times it wasn't.I isolated the problem to the PS4-Router communication, as my ps3 (and everything else at home) worked perfectly with no changes to the setup. Possible Solution- Today, I factory reset both devices (Netgear and TP-Link routers) and set them up to the point where they worked normally (with my phone, laptop, etc).Then, I enabled UPnP on BOTH devices, and also Forwarded all the necessary ports for my PS4 on the TP-Link router.I changed the wireless channel on the TP-Link to [1] from [6].I also changed the wireless channel width on it from [auto] to [20mhz]. This automatically reduced my max Tx rate to [130mbps] from [300mbps]. (I suggest doing this manually if it doesn't change automatically).I rebooted the TP-Link router, and started up my ps4 after a few seconds. The system loaded perfectly, PSN signed in instantly, and I played an hour on BF4 with no problems. I also restarted my PS4 again to see whether the settings would 'Stick'. They did, it still ran perfectly. I won't play again for a few hours, but I will report here if it does/doesn't work. Good luck trying my solution, Hope it works for you.Happy Gaming

Similar Messages

Can't sign in to my psn error code ce-33987-0

ive been trying to sign into psn for the past hour and keep getting this error code tried its suggested actions and checked my isp but there telling me its all ok there end and its the psn network can any one help me on this

I've been having the same problem for over a week, but I think I found the solution to it.Firstly, my internet setup is an old netgear modem-router combo hooked up to a new TP-Link (n) router. The netgear is set to modem only mode. My ps4 is connected wirelessly downstairs.For about 3 months, my ps4 was working normally with no problems, but about a week ago this error code started popping up inconsistently. Sometimes everything was fine, most times it wasn't.I isolated the problem to the PS4-Router communication, as my ps3 (and everything else at home) worked perfectly with no changes to the setup. Possible Solution- Today, I factory reset both devices (Netgear and TP-Link routers) and set them up to the point where they worked normally (with my phone, laptop, etc).Then, I enabled UPnP on BOTH devices, and also Forwarded all the necessary ports for my PS4 on the TP-Link router.I changed the wireless channel on the TP-Link to [1] from [6].I also changed the wireless channel width on it from [auto] to [20mhz]. This automatically reduced my max Tx rate to [130mbps] from [300mbps]. (I suggest doing this manually if it doesn't change automatically).I rebooted the TP-Link router, and started up my ps4 after a few seconds. The system loaded perfectly, PSN signed in instantly, and I played an hour on BF4 with no problems. I also restarted my PS4 again to see whether the settings would 'Stick'. They did, it still ran perfectly. I won't play again for a few hours, but I will report here if it does/doesn't work. Good luck trying my solution, Hope it works for you.Happy Gaming

Can't login to psn. error code: CE-33992-6

please help me!!

Follow steps on this thread - http://community.eu.playstation.com/t5/PSN-Support/Error-CE-33992-6-Solved/m-p/21112529#M40567

HT4009 Unfortunately, I keep getting the error "can not connect to iTunes. Code:0" I've tried rebooting, signing out of my apple ID, can someone please help or advise me on what to do? Many thanks, Ryan

Unfortunately, I keep getting the error "can not connect to iTunes. Code:0" I've tried rebooting, signing out of my apple ID, can someone please help or advise me on what to do? Many thanks, Ryan

hi i had the same problem today when i updated my itunes to latest version. however, i have just found my songs in the 'itunes media' folder. this was accessed through 'my music' then keep clicking through until you find itunes media and all my library songs were in there and i then just added these files to my library and all were restored however, i have lost all my playlists but at least my 700 songs are back. very dissapointed with apple that they have let this happen with their latest update, the previous version was miles better than this one . hope you find them. stevo

Can´t connect to PSN

The last two weeks I have had problems with signing into PSN, and I have recieved different error codes. They tell me the same thing that I can´t connect to PSN within the time limit etc.. What do I do? Please help!! thanks

PSN is having issues but they won't admit it. I got a specific error code from their support page saying it neant their servers were down.

Crystal Server 2013: How to troubleshoot "Can not create temp file---- Error code:-2147215357"

We have a Java7 web app, which generate PDF report by calling Crystal Server 2013 SP4.
The app is being deployed on many different servers. We sometimes got the error below when generating report:
com.crystaldecisions.sdk.occa.report.lib.ReportSDKException: Can not create temp file---- Error code:-2147215357 [CRSDK00000615] Error code name:internal
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.controllerExportInternal(PrintOutputController.java:280)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:152)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:130)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:113)
Problem is, this seems to be a pretty generic exception. It could be caused by many different reasons.
e.g. network connection problem, wrong DB login, wrong folder path, lack of folder access right, etc.
Each time we could only guess what's wrong.
We are running into it again, and this time everything seems correctly configured so far.
We wonder if there are more info we can get to troubleshoot? For example, any log file of Crystal Server we should look into? Or does Crystal Server has debug mode which prints more details to tell us what goes wrong?

Prithviraj Shekhawat wrote:
Hi Henry,
I believe you are using RAS SDKs to export the reports to PDF.
Apply trace on RAS server and check what you find in RAS logs.
Check whether you can see timeout error is RAS logs. Usually if connection is lost and the RAS server no more have the session to write to the temp directory, we do see these errors.
Also, does the account that runs RAS have permissions to create a file in RAS's default temp directory? Are you getting any out of memory or out of disk space exceptions on App server or RAS, tracing RAS server is the way to move forward.
Thanks,
Prithvi
>>I believe you are using RAS SDKs to export the reports to PDF.
Yes
>>Apply trace on RAS server and check what you find in RAS logs.
>>Check whether you can see timeout error is RAS logs.
How to configure tracing, and where are RAS logs? Is it configured in CMC --> Servers --> Crystal Report Services?
>>Also, does the account that runs RAS have permissions to create
>>a file in RAS's default temp directory?
Pretty sure yes.
>> Are you getting any out of memory or out of disk space exceptions
>>on App server or RAS, tracing RAS server is the way to move forward.
Not on App server.
For RAS, that's the problem, I am not sure where to look.......

Error sending emails to Internet: Failed to connect. Winsock error code: 10051

Our exchange 2013 CU2 (CAS+MBX, Win2012) was sending emails to Internet using another server (a kerio email server) and outbound internet email was working as expected.
We have now removed the Kerio server, I also removed the kerio_Send_Connector I was using to send emails to internet and I also changed the email domain in Exchange to be authoritative. I created a new Internet send connector with default values, but the same
bad behavior is present.
Our Exchange 2013 receives emails internally and externally with no problems. The problems are sending emails to Internet. I am suspecting something in the firewall but i need to do some more research.
If from the same Exchange server I telnet to an Internet email host:25 I do get the smtp banner but as soon as I start typing HELO/EHLO I get disconnected and errors are logged.
Errors when sending emails to any emails address (this is from an email sent to google, all others are the same):
Remote Server at aspmx3.googlemail.com (74.125.136.26) returned '400 4.4.7 Message delayed'
7/1/14 9:52:44 a. m. - Remote Server at aspmx3.googlemail.com (74.125.136.26) returned '441 4.4.1 Error encountered while communicating with primary target IP address: "Failed to connect. Winsock error code: 10051, Win32 error code: 10051." Attempted
failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts. The last endpoint attempted was 74.125.136.26:25'
I cannot find any references from such Winsock error that are related to Exchange 2013.
So far all email is being queued at the Exchange Server 2013. I am afraid to install CU3 and make things worse.
Thanks for your comments.

Just check if the receive connector settings are set to fine
check the send connector properties and see whether it is set to use DNS to route emails through external DNS/Internal DNS or smart host .
Do a telnet to external domain like hotmail,yahoo and see at what transaction you are getting an error
Enable verbose logging, restart the transport service and check if you get the same error in the verbose logs as well
Get in touch with the ISP and see if the port 25 for Outbound SMTP is opened.
YOu can check if SMTP Proxy is enabled in the firewall. If so disable the SMTP proxy in the firewall and check.
Good Luck!!
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question.
That will encourage me - and others - to take time out to help you.
Regards,
Sathish

"connection not available error code - 4161" what...

Hi
I have been trying to upload my workouts to Nokia traker but when I start the application I get the following "connection not available error code - 4161" What does this mean and how do I sort it
Thanks

I did a comparison, and your connection string is different
than mine. Mine does not show any password/userid entries, but
perhaps that's the difference between using SQL and SQL Express.
(I'm using SQL.) I am, of course, assuming that you have actual
values for "servername," "database," etc.
Given that you can't get in from RSC Explorer, it would seem
that either you are not using the same userid/password as the one
you set up for the administrator when you created the DB, or else
there's something wrong with the DB itself.
Try creating a test DB. Be careful to specify the same
administrator name and password as the login you use to get on the
RSC server. After you've created the test DB, open it up from RSC
Explorer. If you can do this successfully, then everything ought to
be working OK. From that point, I'd start over and create a new DB,
and upload to that one. (In fact, I've actually gone through
exactly that total exercise before.
G

Can not create temp file---- Error code:-2147215357 [CRSDK00000615] Error code name:internal

Hello,
While exporting Export reporting from BI4 getting exception
Can not create temp file---- Error code:-2147215357 [CRSDK00000615] Error code name:internal
In Trace Log I am getting
com.crystaldecisions.xml.serialization.XMLWriter||Failed to create an object instance for CrystalReports.TextObjectFormat
java.util.MissingResourceException: Can't find resource for bundle java.util.PropertyResourceBundle, key CrystalReports.TextObjectFormat
at java.util.ResourceBundle.getObject(ResourceBundle.java:374)
at java.util.ResourceBundle.getString(ResourceBundle.java:334)
I tried following solution according to the all forums but still issue exist.
Done changes mention in KB article In <Installation-dir-of-BO>\Common\4.0\java\CRConfig.XML we have to increase the JAVA heap MIN and Max size
<JVMMaxHeap>64000000</JVMMaxHeap> <JVMMinHeap>32000000</JVMMinHeap>
Increase the value in the ReportApplicationServer Services in the CMC for "Number of database records to read when previewing or refreshing a report". The value -1 is for unlimited records but not recommended for performance.
Check for temporary read write permission on server
Using SDK library from C:\Program Files (x86)\SAP Business Objects\SAP BusinessObjects Enterprise XI 4.0\java\lib
Can you please let me know is there anything missing.

Hi,
We face the same problem with some BI4 reports.
The same report works well with the "Crystal Reports Viewers API", as used in Infoview, but not with the "Report Application Server (RAS) API".
This error appears after some time working on a report. If we reproduce the same report, but from zero, no problem.
Hope it can help.
Ludovic.

The operation can't be completed because one or more required items can't be found. (Error code -43)

When I attempt to add files to...or copy to the desktop of my mac, my icloud (idisk ..the blue icon on my desktop) is giving this error:
The operation can’t be completed because one or more required items can’t be found.
(Error code -43)
I've been searching for info on that error code, but I'm not find anything on (many different error codes, but not -43).

I get an error -36.
I did the dot_clean in the terminal.
Did not fix it.

I renamed a power point a file and now when I try to open it it keeps giving me the error code -108. If I try to open or copy it say: The operation can't be completed because one or more required items can't be found. (Error code -43). What do I do?

I renamed a power point a file and now when I try to open it it keeps giving me the error code -108. If I try to open or copy it say: The operation can’t be completed because one or more required items can’t be found. (Error code -43). What do I do?

Post in Microsoft's Powerpoint (Mac) message boards.

Safari and Chrome "can't connect to webpage" error message

I recently purchased this macbook on the 26th and it was working completely fine the first day. Today i was using my macbook and it was working completely fine, then about 20-30 minutes after turning on and using my macbook webpages failed to load. In safari I would refresh the page and the page would stop loading at about 40%, and when i tried doing using the search bar instead of the URL bar, i would recieve a "Can't connect to server error" saying that safari was unable to connect to Google. On Chrome i tried opening the same page, such as twitter or youtube, and the page would fail to load as well and it would give me the "unable to connect to webpage" error message. Anything connected to the internet won't load as well, such as the app store or even skype. Whenever i restart the computer it begins working fine again, but returns to its previous state after 20-30 mins again. I have tried restarting my router and even connecting to a different router. I have also checked my proxies and nothing is selected. I am just wondering what to do at this moment, should i take my computer in so soon? Or should I give the computer some time to get "broken in."? My macbook is running Mac OS X Lion 10.7.4
Preferences
1
2
3
4
5
6
7
8
9
0
=
Backspace
Tab
q
w
e
r
t
y
u
i
o
p
Return
capslock
a
s
d
f
g
h
j
k
l
shift
`
z
x
c
v
b
n
m
shift
English
alt
alt
PreferencesI r

Do you have Little Snitch installed?
See: https://discussions.apple.com/thread/3892943?start=0&tstart=0

How can i fix a 4280 error code when trying to burn cd's on itunes

How can I fix a 4280 error code when trying to burn cd's on itunes for windows? Model drive is drive D: TSSTcorpCDRWDVD TS-H492C

Did you by chance find out a solution with your problem? I am having the same issue with the same drive. I even uninstalled iTunes and completely reinstalled it.
Thank you for any help anyone can offer. I'm not having any luck finding answers on the net. Thx.

HT204406 what can I do with an error code -50 network reset message?

what can I do with an error code -50 network reset message?

Hi ddelacruz,
Thanks for using Apple Support Communities. This article has some information on error (-50):
iTunes Store: "Error (-50)" when downloading purchased content
http://support.apple.com/kb/ts1583
Cheers,
- Ari

"Can't connect to server" Error

I'm using a 24" iMac running 10.6.7 and I keep getting a "can't connect to server" error with Safari for certain websites. While I could have posted this topic under the Safari section, the problem is not Safari. I tested other web browsers on my iMac (Firefox and IE) and still got an error. I did all the trouble shooting like: empty cache, reset safari, cookies, proxies, /index.html. Now, I was thinking it could be my router, but I am able to access those websites through my iPhone and my iPhone is connected to my wireless router. So I figured the problem is with my iMac settings.
Websites trying to view:
http://www.rangerboard.com/
http://www.serebiiforums.com/
Any help?

Hi Opti1CS,
Welcome to the forums!
Have you tried a clear the DNS cache?
I found that I switch networks allot; witch leans my DNS cache rather jumbled up. After having to reset the DNS cache for the 10th time in a week. I ended up stumbling over DNS flusher. I find it easer then memorizing a terminal command.

Can't connect to PSN. Error code: ce-33987-0

Similar Messages

Maybe you are looking for