Can't connect to router with non airport wireless

I try again... my Imac won't connect wireless to my router. It actually connects, Imac says everything is fine, but when I connect to the internet, the colourfull little wheel is spining for hours...and nothing shows up.
With the same settings, using Airport express, wired on the router, everytihng is working fine. I can't just switch to the other network.
Any cue?

You have a non-apple wireles card in the IMAC. Why would you do that?
Sounds like your wireless card is not getting an IP adddess. Check system preferences - network and verify both the ethernet and the wireless connections are getting DIFFERENT Ip addresses.You have to go to your wireless cards website to find out how to connect it to an AEBS. Linksysy has info on their site. Also your AEBS has to be set up to distribute IP addresses, otherwise, the AEBS and the IMAC may have the same IP adress and the system won't accept that.

Similar Messages

Frustrated - Can't connect to router with laptop after disconnect, other devices work fine.

I have a RevI Actiontec router with dual antennas(not sure of firmware as I am not at home). My wife can be on her laptop all day, then when I come home with my IPad, it make her lose connection to the router. The router still connects to my iPhone 4 and iPad (both with iOS 6.0.1), but she is unable to connect to router at all. Everything continues to function normally on my Apple devices, so we are still connected to the internet. I have a laptop as well, and when this is happening, both of the laptops stop connecting, but the apple devices and our Toshiba TV and BluRay players continue to function normally. As a temp fix, I disconnect internet from my iPad and restart the router. It works until we try to run both at the same time.
I am mildly computer literate, though I know little about network setups beyond security, MAC filtering, and other slightly advanced setup stuff.
This is really frustrating and seems to be getting worse. We used it like this in our new house for several months before this started happening.

Also check to make sure neither of the devices are set to use a static IP address.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.
"All knowledge is worth having."

Unable to connect AE to existing Non Airport wireless Network

HI Im trying to connection my Airport Express to my existing non airport network so i can use airtunes without loosing my internet connection... When i do this in Airport Utility it asks for the network name and password of the network i want to join i enter it and i press continue and then a message comes up saying it cant find the AE any more and that i should reselect it from the list and try again but i cant see it in the airport list to retry it until li do a hard reset on the AE.
Any Ideas

What did you do? I'm having the same problem.

HT5304 Hi Guys, I'm running snow leopard 10.6.3 recently had update which left me with a DMSL launch problem. Rei installed software and now can't connect to Internet with cable or wifi ! can see network and router,. Help

Hi Guys, I'm running snow leopard 10.6.3 recently had update which left me with a DMSL launch problem. Re installed software and now can't connect to Internet with cable or wifi ! can see network and router. Have tried many things and now pulling my hair out !

recently had update
Care to share which update?
Have tried many things
Care to share?
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.

Will a NAS Plugged into a Non-Airport Wireless Router work with TM?

Will a NAS Plugged into a Non-Airport Wireless-N Router work with TM?
I'm looking for a backup solution for my new MacBook Air and I don't want to spend $200 extra for a Time Capsule when an NAS would do the job.
Any guidance would be appreciated.

No. TM will not backup to any NAS other than Time Capsule

Airport Extreme as a router with an existing wireless DSL

can someone tell me how to set up my Airport Extreme to use as a wireless router with an existing wireless ATT DSL modem?

Hi - can you clarify what you mean by "use a wireless router" - you cannot use it as an addtional router without causing a "double NAT" condition which is not recommended - you can only do this if you change the DSL modem to a "dumb" modem like a cable modem - you also cannot wirelessly extend the network of a non Apple product - you can however can use it in bridge mode via ethernet to create a wireless network with the same name, security and password as the DSL modem in a different location - you can also use it to join your existing network as a wireless access point and provide ethernet to a remote location but not provide a wireless signal.

Can't connect to wifi with my iPad

can't connect to wifi with my iPad

iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HT4972 can't connect to network with linksys e2500

Can't connect to network with linksys E2500. Can anyone help me?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I can't connect to wifi with iPhone5. Does anyone knows why? and what to do?

I can't connect to wifi with iPhone5. Does anyone knows why? and what to do?
Thank you.

The Holy Mecha of Wifi
Turn router off then on Try turning your wireless router off then back on.
Change or turn off wireless security You may want to try toggling the settings on your wireless router, switching from WPA to WEP or vice versa, or, as a last resort, turning wireless security off altogether. For AirPort routers, this can be accomplished with the AirPort Admin Utility. For other routers, this can usually be accomplished by accessing the router’s configuration page — open a browser and enter the address 192.168.1.1.
Reset network settings on iPad. On your iPad, open Settings, then navigate to “General” in the left-hand pane. Scroll down and tap Reset, then select “Reset Network Settings.” This will delete any stored WiFi passwords and other information, but may result in a more stable connection.
Adjust brightness upward. Oddly, a number of users have found that they can resolve this issue by simply adjusting the iPad’s brightness level upward and off the lowest setting. To do this, tap Settings, then select “Brightness & Wallpaper” from the left-hand pane. Slide the brightness bar upward, then wait 1-2 minutes and check for an improvement in signal strength. Speculation holds that a power delivery issue associated with the screen brightness affects Wi-Fi.
Change thresholds in router settings. Access your routers configuration screen (for most routers, open a browser and enter the address 192.168.1.1), then change the fragmentation threshold and the CTS/RTS threshold as described here. Some users have found success with the settings Fragmentation= 2048, RTS = 512.
Change 802.11 spec on router. Try changing your router’s wireless spec mode from B, G and N to G only or vice versa. For AirPort routers, this can be accomplished with the AirPort Admin Utility. For other routers, this can usually be accomplished by accessing the router’s configuration page — open a browser and enter the address 192.168.1.1.
Switch routers. Although a far-from-ideal solution, some users have found success with switching to a different wireless router.
Turn off “Ask to Join Networks.” To do so, tap Settings on your iPad, then select “Wi-Fi” from the left-hand pane. Slide “Ask to Join Networks” to off. Speculation holds that leaving this option on causes the iPad to constantly seek networks, resulting in some type of interference with the network to which it is connected.
Forget network then rejoin. Tap Settings on your iPad, then select Wi-Fi from the left-hand pane. Choose the network with which you are experiencing difficulty, then select “Forget this network.” Go back to the previous screen and rejoin the network.
Turn off Bluetooth. Some users report that, perhaps due to interference issues, turning off Bluetooth can boost Wi-Fi signal strength. To do so, tap Settings then tap General in the left-hand pane. Tap Bluetooth in the right-hand pane, then slide to off.

Hp6700 Printer: can't connect to D-Link DI-514 Wireless Router when Broadcast SSID is set to NO.

HP6700 Printer: can't connect to D-Link DI-514 Wireless Router when Router Broadcast SSID is set to NO. My MAC LapTop and HP LapTop both work with the SSID set to NO. If I change the Wireless Router to Broadcast SSID is YES, then the HP6700 Printer can connect to the Wireless Router. I setup the Printer telling it what the SSID and Password were, the same as both of my LapTops, but it never connects, unless I change the Router to broadcast the SSID. Help!
This question was solved.
View Solution.

Did you try updating the firmware on the DI-514?
You can also try setting a static IP on the printer, then assign the printer to the static DHCP list in the router interface.
To give your printer a static IP address:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway.
- Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS. This is Google DNS. You can choose another external DNS if you wish.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you will have delete and re-add the printer on your Mac.
Show support by clicking the blue Kudos star in the post that resolved your problem. Doing so will help other forum members find their solutions too.

Can't Connect to Router Manager

I want to review the Router Statistics but can't get connected.
I have typed in the address,
http://192.168.1.1/
Also tried via the Router Icon &
http://voyager220v.home/
but get message "Can't Connect to Router"
All other web sites are easy to get into.
Any idea of why this problem is occurring?
Solved!
Go to Solution.

Have you tried rebooting the Voyager or resetting it to default by pressing the recessed reset button.
Are all the lights on at the front, and the correct brightness?
Failure of the Voyager 220V power supply was fairly common, but any 12V regulated power unit will work, if it has failed.
The Voyager range of modems were some of the best, I still have quite a few as standby routers and extra wireless points.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Can I connect my ipad2 with my aiport express without a pc?

Can I connect my ipad2 with my aiport express without a pc?

Yes. However, you would need a PC or Mac to administer the AirPort base station.

EA6500 can't connect to Router after Time Machine

Just got an EA6500 - updated to the latest available firmware.
I've attached 2 x WD NAS and 1 x WD via USB to the unit.
Everytime AFTER I finished running Time Machine on the MacBookPro (writing to one of the WD NAS), I can no longer login to the router neither from the local IP address nor the cisco cloud connect. The error message that I get (loosely phrased) is: can't connect to Router. Please ensure the router is connected to the internet.
At this point, all the devices connected to the router (both wired and wireless) still can access the Internet perfectly. Only the router console is no longer reachable.
Anyone else are having the issue?
Any ideas on how to resolve it?
Solved!
Go to Solution.

Contacted Cisco support and the person advised me to do a factory reset (eventhough the router is brand new with no customization!!). Regardless, it now works properly. Cisco Cloud Connect still works before, during and after a Time Machine session.
"When in doubt, try turning the electricity grid off and on"

TS1398 Can't connect to hotspot with my iPad, picks it up but unable to connect. Any sugestions?

Can't connect to hotspot with my iPad, picks it up but unable to connect. Any sugestions?

When Access Connections fails to connect it asks if I want to configure the network and there's a bunch of settings. Connection type: infrastructure or Adhoc, Wireless security type "use static WEP keys", "Use Wi-Fi protected Access - Pre Shared Key (WPA-PSK)" - I choose it and under Properties there's more options. Access point authentication, WPA-PSK or WPA2-PSK; I've tried it both ways. Data encryption: TKIP or AES, I've been using TKIP. Under Pre-Shared Key, there's the only box I see to enter a password, so I enter the password there.
Chances are pretty good that the problem is the network configuration of your PC and not the AirPort Extreme Base Station (AEBS). What configuration options you choose will depend on how you set up the AEBS's wireless network, but the following can be used as a guideline:
o Connection Type: Infrastructure
o Wireless Security Type:
AirPort Setting = PC Setting
o WEP = WEP
o WPA Personal = WPA-PSK w/TKIP
o WPA2 Personal = WPA-PSK w/AES

Buying Mac MIni (GIFT) Can i connect it to dual non-mac displays?

okay, If i buy the lower end mac mini as a christmas gift for my brother, can i connect it to a display not made by apple. If so, What addapters/Programs/Drivers do i need
2::::
Can I connect it to multiple non-apple displays? If so, Again How??

The mini can connect to most digital (DVI) monitors and to standard VGA monitors (via included adapter). So you should be OK.
The "low-end" Intel Mini is a very nice computer.
For many tasks, such as running legacy PPC Mac programs like MS Office, it will perform much better if you buy it with at least 1024 Meg of RAM memory, rather than the standard 512 Meg RAM.
If your brother won't be running legacy apps like MS Office or Photoshop, then 512 Meg is OK -- though more RAM provides a substantial performance increase.
BTW -- what a nice brother you are!

Can't connect to router with non airport wireless

Similar Messages

Maybe you are looking for