Can't connect to the internet using WLAN on my nok...

i tried to connect to the internet with nokia WLAN on nokia E63 but it says connection fail,please review to your network settings.when i changed my connection settings to WLAN,then i searched for the wireless,i found it and connected to it but still it won't connect to the internet but i discovered some settings on my phone under the acces points and i saw the wireless connection access already defined there so i clicked on it and found so many settings under it but don't understand any e.g pre-shared key e.t.c ... someone please help me. Thanks.

Hamzat_kudus wrote:
but don't understand any e.g pre-shared key e.t.c ... someone please help me. Thanks.
Welcome to Nokia Discussions, Hamzat_kudus.
The pre-shared key is the password or passkey needed in order for the phone to establish a connection with the Wi-Fi source. This is explained more further on this page http://en.wikipedia.org/wiki/Pre-shared_key
To setup Wi-Fi on your phone:
Open the WLAN Wizard and perform a scan.
To start or continue browsing the web using the access point of the WLAN, scroll to the desired network, and select Options > Start web browsing or Cont.web browsing . Enter the password of your router and proceed.
To view the details of the WLAN, select Options > Details . To save the access point of the WLAN, select Options > Define access point .

Similar Messages

I just downloaded the latest OS upgrade and since I can not connect to the internet using my cellular data plan.

I just downloaded the latest iOS.7 upgrade on my ipad2, and since I can not connect to the internet using my cellular data plan. I have checked my data plan and it's both current and over 2GB remaining. However the indicator shows no service, thus would be the best steps to recover. Thanks much for any support that can be provided.

Hello Kmart2@3
Check out the troubleshooting article below to get cellular to start working again.
iPad (Wi-Fi + Cellular Models): Troubleshooting a cellular data connection
http://support.apple.com/kb/TS4249
Regards,
-Norm G.

Can't connect to the internet using a PPPoE connection

Helllo,
I have a LinkSys Wireless-G 2,4ghz, and i used it for 4-5 months, but for a week now i can't connect with it to the internet.
I have a Internet connection using a PPPoE, I plugged the cabble directly in the PC and made the connection and it works, so there is no problem with the internet.
When i am trying to use it with the router it dosen't work, i have selectes the PPPoE connection then user and password, i press connect and it sits at "Connecting ..."
The Internet light is on when i put the cable in, so the port is working, and it is allso blinking witch means it sends some packages.
I have tryid to get some logs to see what is going on but faild, the only thing that i go is:
Dec 31 16:08:36 unknown user.info redial[263]: Started. Time: 30Dec 31 16:07:10 unknown daemon.info dnsmasq-dhcp[187]: DHCPINFORM(br0) 192.168.1 .114 1c:6f:65:a8:04:ecDec 31 16:07:10 unknown daemon.info dnsmasq-dhcp[187]: DHCPACK(br0) 192.168.1.11 4 1c:6f:65:a8:04:ec mirona-nou-PCDec 31 16:07:24 unknown user.info redial[189]: WAN down. Reconnecting...Dec 31 16:07:24 unknown daemon.info dnsmasq[187]: exiting on receipt of SIGTERMDec 31 16:07:25 unknown daemon.info dnsmasq[196]: started, version 2.51 cachesize 150Dec 31 16:07:25 unknown daemon.info dnsmasq[196]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N DHCP no-scripts no-TFTPDec 31 16:07:25 unknown daemon.info dnsmasq-dhcp[196]: DHCP, IP range 192.168.1.100 -- 192.168.1.149, lease time 1dDec 31 16:07:25 unknown daemon.warn dnsmasq[196]: no servers found in /etc/resolv.dnsmasq, will retryDec 31 16:07:25 unknown daemon.info dnsmasq[196]: read /etc/hosts - 0 addressesDec 31 16:07:25 unknown daemon.info dnsmasq[196]: read /etc/hosts.dnsmasq - 1 addressesDec 31 16:07:30 unknown user.info redial[198]: Started. Time: 30

try the reset:
http://compnetworking.about.com/b/2009/03/11/the-30-30-30-hard-reset-rule-for-routers.htm
then reconfigure the router...
BTW, who is your ISP? What is the model of your modem?
Yesterday is history. Tomorrow is mystery. Today is a gift.

I updated to firefox 8 last night - now I can't connect to the internet using firefox at all!

I had trouble installing the new version of firefox yesterday, too... I had to go to the webpage and do a manual install. Today I tried uninstalling Firefox and reinstalling it, but that didn't fix the problem.
My internet connection shows full bars and works just fine with IE, so this is definitely a Firefox-specific issue.
i had to resort to ie just to report this problem. what's up, firefox? i've never any trouble and have been using your browser for 5+ years.

A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.com/kb/Server+not+found
*https://support.mozilla.com/kb/Firewalls

Why can't i connect to the internet using airport

I can't connect to the internet using Airport. I have to use a ethernet connection.

go to applications>utilities, and make sure your wireless is showing up in the left colum. If you see it there follow the promps to set it up

Why is my wi-fi signal is going strong, but I can't connect to the internet?

Before I begin, here's my set-up:
My wi-fi signal (on the top right side of my MacBook) is going strong (with all the bars). And a green light is lit up on my Airport Extreme. For some reason, I still can't connect to the internet/use Apple Mail/use iChat. I don't think that there's anything wrong with my MacBook, as my wife isn't able to connect to the internet with her iPad or with her laptop either.
I'm thinking that I have the strong wi-fi signal showing up on my computer because it actually is connecting to the Airport Extreme, yet the airport extreme somehow isn't connected to or isn't able to connect to the router. Would this be correct? Any ideas of how I might fix this? I tried unplugging and replugging everything for a few seconds. However, whenever I use a hardwire ethernet connection to my MacBook, my internet and everything works.
ALSO, of note, I just purchased an Apple Time Capsule. I just realized that it functions as a wi-fi base. Any chance that my computer, my wife's iPad and laptop are just connecting to the Time Capsule instead of the Airport Extreme?
Any answers would be more than appreciated. Thanks!

Deselect Proxies if selected.
Safari > Preferences > Advanced > Proxies:
Click "Change Settings" button
The network preferences window for Proxies will will show up with "Proxies"
tab selected.
Under "Select Protocol", uncheck any box if selected.
Click "OK", then "Apply"

Switched from DSL to Cable, Can't connect to the internet

After switching to cable modem (Motorola SB5120 SURFboard) from DSL, I can't connect to the internet using my airport express. Everything is green - modem and airport, and the signal on my computer looks like I have full access, but there is a scrolling message... looking for PPPoe host. I have unplugged everything and restarted per the instructions on this site, but get the same result every time. My computer connects just fine using direct connection to the modem. I saw a download for a firm ware update for the express, but don't know how to apply that, either. Any help out there?
Thanks!

Hello mom2gr82. Welcome to the Apple Discussions!
Let's double-check your AirPort Express Base Station's (AX) settings...
AirPort Express Base Station Setup (AX) w/High-Speed Cable Modem
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
Modem/Router Power ReCycling
o Power-off the Cable modem, AX, & computer(s); Wait at least 30 minutes.
o Power-on the Cable modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
Setup the AX
Connect to the AX's wireless network, and then, using the AirPort Admin Utility, try these settings:
AirPort tab
o Base Station Name: <whatever you wish or use the default>
o AirPort Network Name: <whatever you wish or use the default>
o Create a closed network (unchecked)
o Wireless Security: Not enabled
o Channel: Automatic
o Mode: 802.11b/g Compatible
Internet tab
o Connect Using: Ethernet
o Configure: Using DHCP
o WAN Ethernet Port: Automatic
Network tab
o Distribute IP addresses (checked)
o Share a single IP address (using DHCP & NAT) (enabled)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
Change Wireless Security
o Wireless Security: WPA Personal or WPA2 Personal
o Encryption Type: WPA and WPA2
Base Station Options - WAN Ethernet Port
o Enable Ethernet Port (checked)
o Enable SNMP Access (unchecked)
o Enable Remote Configuration (unchecked)
o Enable Remote Printer Access (unchecked)

Can not connect to the internet. This is a new problem since I have been using firefox for years.

I can not connect to the internet. I called mediacom due to the problem and they connected me to internet explorer. They indicated I should contact you for help in connecting to the internet. It appears firefox has made some kind of change since last night since I was using firefox for my internet connection last night. Something has changed. Your help will be appreciated.

http://en.wikipedia.org/wiki/Keyhole_Markup_Language
The only way that file opens thru IE8 for me ''(but not actually in IE8)'' is by using the Zip Utility (then IE closes) that is in WinXP and then opening the two image files in the Windows Fax and Picture Viewer.
I think Firefox is trying to display that file because the MIME-type is for '''''text/plain''''' instead of the appropriate MIME-type of '''application/vnd.google-earth.kml+xml''' or '''application/vnd.google-earth.kmz'''
That is something that needs to be configured in the server that is hosting that file type. Sorry, I don't know how that can be fixed. The one support person here that might know lives in Europe ''(I believe)'', so you might need to wait for an answer.

I've updated to yosemite from Mavericks, but since i can't connect to the internet I used my time machine back up which was march 2013. Now my macbook pro won't start and ends with a prohibited ted sign. Any suggestions pls.

I've updated to yosemite from Mavericks, but since i can't connect to the internet I used my time machine back up which was march 2013. Now my macbook pro won't start and ends with a prohibted sign. Any suggestions pls.

Install or Reinstall Yosemite, Mavericks, Mountain Lion, or Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
OS X Mavericks- Erase and reinstall OS X
OS X Mountain Lion- Erase and reinstall OS X
OS X Lion- Erase and reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.

I can not connect to the internet while using my ipad I get a message saying Safari could not open the page because the server stopped responding need help thank you

I CAN NOT CONNECT TO THE INTERNET WHILE USING MY IPAD I KEEP GETTING A MESSAGE SAYING SAFARI COULD NOT OPEN THE PAGE BECAUSE THE SERVER STOPPED RESPONDING PLEASE HELP THANK YOU

Try the following:
1. Turn router off for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings
3. Reset iPad; hold the Sleep and Home button down until you see the Apple Logo

After a recent comcast / xfinity update I have been unable to even connect to the internet using firefox. I can using internet explorer.

After a recent comcast / xfinity update I have been unable to even connect to the internet using firefox. I can using internet explorer.

Take each of the following steps that you haven't already tried, until the problem is resolved.
Step 1
Restart the router. Many problems are solved that way.
Step 2
Change the name of the wireless network, if applicable, to eliminate any characters other than letters and digits. You do that on your router via its web page, if it's not an Apple device, or via AirPort Utility, if it is an Apple device.
Step 3
Run the Network Diagnostics assistant.
Step 4
Back up all data.
Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
Enter the name of your wireless network in the search box. You should have one or more "AirPort network password" items with that name. Make a note of the name and password, then delete all the items. Quit Keychain Access. Turn Wi-Fi off and then back on. Reconnect to the network.
Step 5
You may need to change other settings on the router. See the guidelines linked below:
Recommended settings for Wi-Fi routers and access points
Potential sources of interference
Step 6
Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
Step 7
Reset the System Management Controller (SMC).

TS1398 I can't connect to the internet while using wi fi on my iphone 4S.

I can't connect to the internet while using wi fi on my iphone 4S. I can connect on my computer and on my IPad but not with my iphone. I have tried everything. Once or twice it did connect but then disconnected immediately. I have tried everything.

LeeinSunnyIsles wrote:
I can't connect to the internet while using wi fi on my iphone 4S. I can connect on my computer and on my IPad but not with my iphone. I have tried everything. Once or twice it did connect but then disconnected immediately. I have tried everything.
If you have truly tried "everything" then there is no hope of it ever working again. However, have you tried rebooting your router?
Have you tried Settings/General/Reset - Reset network settings?

Equium A200 can not connect to the interest using Wifi

Hi,
Since having to reinstall Windows Vista Ultimate, I can not connect to the interest using Wifi. It works fine for Ethernet, but when choosing the "Connect to the Internet" screen, its blank and will not find any wifi connects or let me manually connect to one.
In Device Manager under Network Adaptors, it now only shows the Ethernet Controller and not the Wifi adaptor. I have tried to download the driver from this site and after rebooting nothing has changed. I have made sure the machine has all the latest Windows updates as well. I have also mader sure that the wifi button is switched on at the front of the machine.
Also one a side note I cant seem to find the exact name of the Laptop in the system section of Control Panel other than Equum A200. On the download driver page there is NOT a A200 listed only A300 and A300D.
http://uk.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=UK&mode=allMachi nes&action=search&teddProduct=759&selShortMod=667
Any help would be grateful.
Spec:
Windows Vista Ultimate
Toshiba Equium A200
32-bit Operating System

>Also one a side note I cant seem to find the exact name of the Laptop in the system section of Control Panel other than Equum A200. On the download driver page there is NOT a A200 listed only A300 and A300D.
I guess you didnt look into the Archive the A200 is a little bit older therefore the drivers are placed in Archive!
If you want to know what driver you need then I recommend checking this faq:
http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78
All Wlan drivers can be found here:
http://aps2.toshiba-tro.de/wlan/

After update I can't connect to the internet in no way, shape or form

I rarely update because: 1) something always breaks when you update (like now) and 2) I don't like to deal with new crap like GNOME 3. Anyway:
I bought a new router (TL-WR1043N) and configured it with an old Ubuntu because connecting to 192.168.1.1 didn't work on any of my Arch Linux installations. Now... here's where it all starts... I can't use the 'n' wireless on my laptop since I have to install something to use WPA, and to install that I need to update, but I don't want to deal with GNOME 3 and Firefox >3. But I gave up eventually gave up and connected my laptop to the router by Ethernet cable. Setting that up was very easy: 'ifconfig eth0 up; dhcpcd'. Voila! I updated my whole system and restarted. To see how badly I damaged my system I opened Nautilus (I use Openbox with some GNOME programs): shock and dismay, the fonts are visible from the moon. I guess I'll have to quit using GNOME programs completely now but I expected that. I used to use KDE back in the day and when KDE4 came forth from that unholy pit, I immediately abandoned it for GNOME. This time we had more time to prepare, everybody knew what GNOME 3 was going to be. I started using Openbox quite a long time ago.
Anyway: Now to fix my wireless right? WRONG! I can't connect to the internet on cable to get the packages for wireless. I installed Windows 7 64 on the same laptop and it connects to the cable. Ubuntu 9.10 Live also connects, but due to the changes of rc.conf and network stuff I can't connect at all with Arch Linux.
So I decided to abandon it completely and reinstall from scratch. But the Live CD also doesn't work. With all the ways I've tried it all comes down to this:
dhcpcd always times out waiting for a carrier and 'ip addr' shows 'eth0: <NO-CARRIER, ....' if the interface is up. I'm not sure what information I should give you, but I can't paste any here since I can't connect to the damn internet on that laptop.
About the router: the cable is plugged on port 1 and the LED for it flashes if I reboot the computer. In Windows it stops flashing while it connects and flashes again when connected. I removed 'network' from DAEMONS and it flashes till I start it with '/etc/rc.d/network start'. This hangs for a while and returns '[DONE]' even though it doesn't work and the LED never flashes again on the router.
In rc.conf I have exactly what the example says for DHCP. In any case, it doesn't work with the Live CD either.
EDIT 1: From lscpi: painstakingly typed:
06:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
07:00.0 Ethernet controller: Realtek Semiconducctor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
EDIT 2: Just to be clear: I can use the wireless on the laptop on the Live CD, but I want to use the cable because of the greater speed (94Mbit/s on cable 60 something on wireless n, 20 something on g) and because I rarely move the laptop.
EDIT 3: lspci -v shows "Kernel driver in use: r8169 / Kernel modules: r8169", so the driver is loaded.
EDIT 4: So if I boot from the CD. ip addr shows:
eth: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:1d:92:...etc... brd ff:ff:ff:ff:ff:ff
And the LED flashes. When I type: "ifconfig eth0 up" it stops, never to light up again and ip addr shows: "eth: <nO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
Last edited by imtired (2011-09-08 12:36:51)

When you're in Arch, use output redirection
lspci >lspci.out
then boot into Ubuntu or something where you can access the files and the BBS, Of course, don't forget to use a new file for each command output.
The new network config in rc.conf is not that complicated (wired anyway; never used wireless). OTOH I've had issues on two machines where I have to restart the network daemon (rc.d restart network) or rerun netcfg (netcfg eth0) after boot to get connectivity. And I still haven't come to grips with the ip command.

Can't connect to the internet

Ok. so i did a search and didn't come across any other problems like the one I'm having.
Let me start off by stating that my laptop is an ibook g4 bought feb, '06 (yes the apple care just ran out).
I'm having a problem connecting to the internet on my ibook, running through a d-link wireless router. I'm using my imac to connect to the internet currently (which works fine by the way). It also is connected through the wireless router.
My ibook has a strange ailment. I open up Safari and all I get is a blank screen, the page is trying to load but the status bar is going no where and does the same in Firefox. So first, I opened Network diagnostics, but the computer freezes and I have to do a hard shutdown. (holding the power button). Next, I tried Disk utility. Verified Permissions, Repaired Permissions, everything is fine. I tried to Verify Disk, and again the computer freezes, will not let me force quit and I am forced to do another hard shutdown. I do the thing where you hold down some key while you're starting up to get into the disk utility so I can repair the disk. This returns clean as well. I downloaded techtool off of my Applecare disk. Did the tests, everything passes. So what's the deal?? I've tried to reset the pram. I even did the Apple Hardware test, everything passed.
I thought it could be my Airport card? It recognizes that there is an internet connection in the top right corner, I even have great signal strength (mostly because I've tried this sitting right next to the router). But still, I can't connect to the internet. Any one have any ideas? I don't know what else to try! Please help!

so i can't believe i didn't try to connect it directly to the router with the ethernet cord. This actually worked. But it still didn't solve my wireless problem. I'm not willing to let my laptop become a desktop. I'm already wired to a plug b/c the battery is slowly dying and has a life of about 5 minutes. I'm not willing to give up my wireless internet too.
I guess now it's got to be the airport card? how do I confirm this? and if it is how much would a new one cost and can I install it myself??

Can't connect to the internet using WLAN on my nok...

Similar Messages

Maybe you are looking for