Can't connect to wireless network with Apple Computers (WRT54G)

Hi.
I have had a password protected router (WRT54G) for over two years that any pc will connect to if I give them the password. However, my roommate has an apple laptop and he can't connect, no matter how many times we try. I just got an ipod touch, and it can't connect to the network either. We are inputting our password correctly - why can't apple computers connect to my wireless network??
Again, my router is a WRT54G.
Thanks !!!
Message Edited by Debo24 on 05-24-2009 06:41 PM

Make sure you enter the correct password...To check your Wireless Settings follow this link
If your Wireless Security is WEP then use WEP Key1 and not the Passphrase, make sure to enter a dollar sign on your Apple Computer when you attempt to connect...If your Wireless Security is WPA/WPA2 then use the WPA Shared key and no dollar sign is required...

Similar Messages

Can not connect to wireless networks with ipad 2

My ipad used to connect to the wireless net at home and in public areas.
Now all by the sudden it can't "see" the network.
Message: " could not connect to wireless network"
I have tried "everything" also on different networks,
except resetting the modem.
My iPhone works, as do all my other computers.
Modem is Zyxel P2812

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

UNABLE TO CONNECT TO WIRELESS NETWORK WITH APPLE WINDOWS COMPUTERS CAN

I am new to Apple and am trying to connect to our at home wireless network.Have a Linksys wireless router that is functioning as far as I know correctly.We are able to connect with windows based laptops.My Apple sees our network which is identified correctly and asks for a password.When we enter the password that functions for the other computers it does not work.I s there a configuration change I need to make.Maybe a password variant? I really want to get this up and running and am out of ideas.
INTEL IMAC 20 IN 2.17 GHZ Mac OS X (10.4.7)

Are you using WEP, if you can try and use WPA.
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
AirPort: Joining an encrypted wireless network
http://docs.info.apple.com/article.html?artnum=106424
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WPA
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix

Can't connect to wireless network with "conflicting" essid

Hello,
My wireless card works perfectly (actually I am using ndiswrapper, but anyway) on Arch and I can connect to my home wireless network. I use iwconfig to connect.
In my office we have a wireless network. It's essid is "default" and it uses WEP. I can connect to it using Windows, but not using Arch. Im running the following commands:
iwconfig wlan0 essid "default" key XXXXXXXXXX
dhcpcd wlan0
and it doesn't connect ("waiting for carrier..." and nothing happens)
I guess the problem is that there is another network with the same essid - "default". I've tried to manually associate my card with my office network AP using iwconfig wlan0 ap XX:XX:XX:XX:XX, but it didn't work either.
What should I do?

What kind of Wireless card do you have and what does it say when you do a lspci? So for me, I know I have a Broadcom and the way I found it was to do:
lspci | grep BCM4312 (or whatever wireless make/model you have)
or
lspci | grep "Network Controller"
The second option should also get it for you. From there, you can check out this list to see if that might help you with drivers (but then again, you might have known this already so...).
Hope this helps.
Last edited by ruffedgz (2009-11-23 21:03:42)

Can't connect to wireless network with Dell Inspiron 1525 with Vista

I set up a wireless network about a week ago, and have made it with the following security features: WEP, enable only certain MAC addresses to connect, and disabled broadcasting the SSID. I have been able to use it just fine with my Mac computer using airport, but when I have tried to connect my roommates computer, a dell inspiron 1525 with vista, it can't connect. I can locate the network but when I try to connect to the network, I get a message saying that for an Windows cannot connect to the network and that the Wireless association failed due to unknown reasons. It then says to connect with your administrator, but that is me. I have a minimal knowledge of computers just enough to be dangerous and am basically figuring this out as I go along. If anyone has some advice for me, both my roommate and I will be very grateful.
Thanks,
- Jill
Solved!
Go to Solution.

Sorry I am not sure if this is needed but I am using a WRT54G router ver.6.

Can't connect to wireless network with encryption.

I have had no trouble connecting to hotel wireless networks, or my college wireless network. However, when I try to connect to my home network wirelessly, or another family member's network wirelessly, my connection times out when I enter the username and password. I have a MacBook Pro if that makes a difference.

Try typing a $ in front of the password.

I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM. My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore. Connected those drives to TM via firewire and could see the drives and access them.
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc. I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads. Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system. I really didn't want to monkey around too much with my system. But are there other options to connect the new TC. Can't find info anywhere for this and called apple who gave me the info above. after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light or repair it in disk utility if it should become corrupted.
For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working. Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
Now a rant. I can't believe in this wireless age that Apple would make a product that cant join a wireless net work. The apple rep said i could return it and look for the previous TC that would join an existing wireless network. Are we going backwards?
Thanks!
lennydas

Ok... it is getting a bit clearer but there are still some questions.
I connect to the internet via airport only and it is pretty fast.
I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc.
I think this is mistaken.
Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
If the computer is close it will be faster than the FIOS.
You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC. the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
Thanks again!
You cannot extend to a non-apple wireless router.
You cannot use join a wireless network because when you do the ethernet ports will be cut off.
But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
Join in the express is the only apple router that still allows an ethernet connection.
For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

Can I extend my wireless network with my old Airport?

Can I extend my wireless network with my old Airport? I have the airport extreme 802.11n & my old Airport (translucent white) base station. Can I mix the two to expand my range?

No problem; ask as many questions as you need to.
How do I reconfigure the Snow as a bridge to allow the AEBSn to continue to provide both NAT & DHCP services for the entire network?
I don't have a Snow to verify this, but it should be similar to the later base stations when using the AirPort Admin Utility.
To set up the Snow base station as a bridge, either connect to the Snow's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the Snow, and then, using the AirPort Admin Utility (located in the \Applications\Utilities folder), make these settings:
Network tab
o Distribute IP addresses (unchecked)
o Apply the new setting.

Can I connect to wireless networks far away?

How do I connect to wireless networks further away?
Is there a way I can improve my laptops wireless range so I can connect to wireless networks further away?

Hi!
You can only connect to wireless networks that the notebook recognizes. If the notebook recognizes a wireless network, you can connect to them. If it doesnt recognize (because it is further away) you can not connect.
Furthermore you can not improve the wireless range from the laptop. You can do this on a WLAN router, not on the notebook.
Bye

Can't connect to wireless internet with my airport extreme card.

hello, i need some help connecting to our wireless router. i do not have an airport base station, i am trying to connect to a third-party, secure wireless network. anyway, i've called apple, i've called linksys (the router company), and i am still using hardwire connected to the router. whenever i click the airport icon on the top taskbar, no networks show up. i have had my pc laptop in the same room as my iMac G5, and the laptop can autmatically connect to the network, but my iMac cannot. i am running out of options. i connect with a secure, wireless internet. its wep, whatever that means, and i've tried my user name and passcode numerous times, but to no avail. what do i do????

thanks for your help, but sadly this did not work. even when i click the wireless airport icon on the top taskbar, no networks show up on the pull down menu. the only option i have is 'other.' shouldn't my secured network at least show up in the pull down menu, to which i provide the password?
is there any way to get this extreme card to work? has anyone else had this same problem with their iMac G5? this is ridiculous, thanks.

How can i extend a wireless network with time capsule

How can i extend an existing wifi verizon wireless network with time capsule? the router is connected on the bottom floor. want to boost the signal to a home office on the top floor, four flights up. connect time capsule via ethernet cable to iMac on 4th floor? Do I have to start a second wifi network or can I set it to just boost the one I have? thank you

How can i extend an existing wifi verizon wireless network with time capsule?
It all depends on what you mean by "extend".
If you plan to "extend" by connecting the Time Capsule to the Verizon router using a wired Ethernet cable, this can be accomplished.
If you were hoping to connect the Time Capsule to the Verizon router using wireless only, unfortunately the Time Capsule and Verizon products are not compatible for that purpose.
Check with Verizon to see if they offer an "extender" or "repeater" that could be located very close to the Time Capsule.
This would provide both more wireless coverage and also allow you to connect the Time Capsule using an Ethernet cable from the "extender" or "repeater".

Officejet Pro 8610 - Can't connect to wireless network

Tried to setup the new printer from both Windows 8 and Vista os. Can't retrieve wireless info (even tho the printer will pick it up). HP used to produce good products.

Hi @Schilling34
I am sorry to hear that this has been a less than satisfactory experience. I would like to help you get the printer working, on the wireless network, with both the Windows 8 and Vista computers. Please use the following document to troubleshoot the issue; 'Unable to Find the Printer' Message Displays on the Computer During a Network Installation.
Although you may not see this 'unable to find printer' error, the steps in this document will guide you through the necessary steps.
Please let me know if this resolves the issue, or if you require further assistance. Thanks.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

With new OS6 I can't connect to wifi network with my iPhone

Ever since I upgraded to the new iOS6, my phone will no longer connect to my wifi networks. It only works on 3G. Tried to reset networks and various other things to no avail. Not happy ...

Hello,
I tried the Apple Support recommendation but nothing works, my Ipad mini still can't connect to wifi network, the wifi function in the setting menu it's not available.
I would like to send my device for technical support in USA. I'm live in Venezuela.
How can I do it?
Thank in advance

Advice on how i can set up an office network with 40 computers.

I am planning on setting up an office network with 40 computers. What do you think is the best way i can do this? Thank you in advance.

Your first step should be to call an IT professional who has experience with this type of thing. He will need to survey the entire area and ask you dozens of questions about how you want things to operate. Then, he will present you with a proposal for the network listing all of the things that the system can and and cannot do.
Your second step would be to call another IT professional who has experience with this type of thing and go through the same procedure.
Your third step would be the same as the first and second.
Your fourth step would be to check the references provided in the steps 1-3 and then decide on which professional that you want to use.

Officejet Pro 8610 - Can't connect to wireless network (and has similar issue with previous printer)

When I returned from a trip, I was unable to connect to my trusty HP All-in-one 7510 that I had on my network for three years. I tried troubleshooting it, reinstalling the software on numerous computers, and fixing the printer, but alas the printer said that it was connected to the network, and none of my computers wanted to find it anymore.
Then I bought my new Officejet Pro 8610 this week, set it up...and I am experiencing the same issue. I tried using the link and support took from this post - http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/Officejet-Pro-8610-Can-t-connect-to-wi... but the printer was unable to be found on the network.
I would appreciate any help on this issue. Thanks!

Hello @Celestialnova ,
Welcome to the HP forums.
I understand that you are having problems with your wireless network.
I would like to help.
Since the same issue happened with two different model of printers, lets take a moment to check the network.
Run through the following document.
Printer Does Not Maintain Wireless Connection
Aardvark1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!

Can't connect to wireless network with Apple Computers (WRT54G)

Similar Messages

Maybe you are looking for