Can't Console into ESW-520-24P Switch, Need help.

Hi,
We have 3 ESW-520-24P series switches.
I can not console them because by default they have a security profile attached into it for "Console Only" and It is set as "Deny".
I can't modify or delete it because it's a default security policy.
We can do console into ESW-540-24P series switches without any problems.
Can someone share any solutions to gain console access for these switches?
Any one from Cisco TAC support?
Thanks in advance.
Mansur.

Hi Devicarr,
Thanks for your reply.
I can set the VLAN and Management IP address using the web interfaces.
But when I am trying to connect it via console it is not responding. I reset it to factory default and then found from the web control panel/interface that the switch has an "Access Authentication" under that it has a "Access Profile" and the profile has a default or built in profile attached says "Console Only" and it has a rule like "IP Source = 0.0.0.0/32 Permit = Deny".
I tried to delete or modify it even I tried to add a new rule to allow the console access but failed.
Does this switch series "ESW-520-24P" by default Console disabled when manufactured or ELSE? Please provide me your valuable suggestions.
Thanks in advance.
Mansur.

Similar Messages

  • Support for WRT610N for ESW-520-24P-K9

    Hi to whom may concern,
    Can the following switches (ESW-520-24P-K9) x3 & ESW-520-48P-K9 able to support inline power for  74 x WRT610N  ?
    Thanks

    Hello batumibatumi,
    The ESW series does not have supported CLI feature. If you are looking for a CLI supported switch, please look into our Sx300 series.

  • Port suspended on Cisco ESW-520-24P

    Hi experts,
    I appreciate if anyone can help me with this. I just bought 4 units of Cisco ESW-520 24Ports switches. I did some testing and found out for PORTS 1 and 12 is in "Suspended" mode and thus not able to use.
    This not happened to 1 but all 4 switches. Why is this so ? Can anyone guide me to disable the ports from going into "suspended" mode automatically ? I wouldn't want the ports to be in "Suspension" mode when it goes live and thus block the desktops from having internet access.
    Thanks!

    Ok, I think I found out what the priblem is.  It seems that from factory, the ports come locked.  You have to go to Security>Traffic Control>Port Security and unlock each port.  Click the EDIT tab on the port you want to edit.  Then un-check the ENABLE TRAP> (apply).  Un-check LOCK INTERFACE> (apply).  Change LEARNING MODE to CLASSIC LOCK> (apply).  That should do it, but you'll have to do that for every port you want unlocked.  I'm not to sure if there is a way to unlock then all at once.
    Daniel

  • About the Maximum of Source Ports to ONE Destination Port on ESW 520 24P

    Does the ESW 520 24P Support Mirroring 20 Ports Traffic to 1 Destination Port?

    Hi Andy
    No the ESW supports mirroring groups that can each mirror  8 ports to a destination port.
    This is great for normal problem determination purposes. I can guess at your application.
    regards dave

  • Problem in connecting ESW 520 POE switches

    Hi
    New on ESW 520 switches
    Need help to configure the ESW 520  24 POE switches
    How can i configure the last port of 24 to oonnect to another ESW 520 24 port switches ?

    Why not use the GE ports at the far right to chain the switches one to the other from the UC540/UC560?  They are best for this and gives you an extra port on the switch this way.  Use straight thru ethernet cables.

  • New UC560 and 3 ESW-540-24P Switches, best way to wire them

    We are installing a UC560 and 3 ESW-540-24P switches at a client in a couple of weeks.  I have installed many of these but have never installed one with multiple switches.  What is the best way to connect these together physically.  They will be all in the same rack.  Was just wondering the best way to "series" the switches together and what ports to plug them into.  Any suggestions would be appreciated.

    There is a Smart Design: Implementation Guide at :http://www.cisco.com/web/partners/sell/smb/tools_and_resources/smart_business_comm_system.html
    Implementation Guide
    Smart Business  Communications System 2.0 – Implementation Guide
    The implementation guide complements the SBCS 2.0 Design Guide through  the detailed guidance for SBCS 2.0 based Main Office deployment. This  document leverages the GUI configuration capability with easy-to-follow  step-by-step network deployment guidance using CCA v2.2. It also  includes an installation checklist to assist during the installation  process. It is recommended that users refer to the SBCS 2.0 Design Guide  for underlying design guidance and considerations.
    In this (figure 6) it shows a 48 and a 24 port switch connecting to each of the UC560 expansion ports (there are 2 GE ports for expansion on the 560).
    These could also be 2 48 port switches (96 total ports).  (In your scenario, I would connect 2 this way and the third to one of  those 2.)

  • For some reason i can't sign into imessage and facetime. PLEASE HELP???

    For some reason i can't sign into imessage and facetime. PLEASE HELP???

    Hey tcap8687,
    After reviewing your post, I have located an article that can help with iMessage and FaceTime. It contains a number of troubleshooting steps and helpful advice for the issue you are experiencing:
    If you have difficulty activating FaceTime or iMessage - Apple Support
    If you see "Could not sign in, please check your network connection and try again" when signing in to your Apple ID
    To resolve this issue, follow these steps.
    Update to the latest version of iOS.
    Verify that you have a data connection by going to www.apple.com in Safari. You can complete Apple ID activation using Wi-Fi or a cellular data connection. If you need help connecting to Wi-Fi, follow these steps.
    If you're using Wi-Fi, make sure that your local Wi-Fi network is using the recommended Wi-Fi settings.
    Sign in to your account and ensure that the primary email address and alternate e-mail addresses have been verified. If verification is pending, follow the instructions in the email Apple sent to that email address to complete verification. Or remove the e-mail addresses from the account.
    If your Apple ID isn't an email address, you can change it. The Apple ID that you're using to activate FaceTime or iMessage must be an email address. Find more information on how to change your Apple ID.
    Tap Settings > General > Date & Time. Make sure that your iPhone is set to the correct time zone. If Set Automatically is on but the wrong time zone appears, turn Set Automatically off and choose the correct time zone, date, and time.
    Enable iMessage and FaceTime while connected to a different Wi-Fi network (in a different location) if a cellular data connection is not available.
    You can see that you've activated FaceTime and iMessage with your Apple ID by following these steps.
    Tap Settings > FaceTime > You can be reached by FaceTime at:
    Tap Settings > Messages > Send & Receive > You can be reached by iMessage at:
    Thank you for contributing to Apple Support Communities.
    Take care,
    BobbyD

  • My iPod touch 4 generation 32gb sometimes is really slow and when ever I get on a app it will shut it down. My lock botton is broken and I use the accesery botton to lock it. That being said I can't power down my iPod. I need help, I don't know what to do

    My iPod touch 4 generation 32gb sometimes is really slow.When ever my iPod is being slow and I get on an app the app will shut down. My lock botton is broken and I use the accesery botton to lock it. That being said I can't power down my iPod. I need help, I don't know what to do! Could you tell me how I can power down my iPod or how I can fix the slowness and the shutting down of the apps.

    - Periodically double click the home button and close all the apps in the recently used dock. Then power off and then back on the iPod. This frees up memory. The 4G only has 256 MB of memory.
    - Next, reset the iPod
    To reset the iPod without the hardware buttons,
      Reset network settings: Settings>General>Reset>Reset Network Settings. All your wifi and bluetooth preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected. You will have to rejoin wifi networks and repair BT devices
    Then you can try:
    - Restore from backup. See:                                                
    iOS: How to back up                                                                                     
      - Restore to factory settings/new iOS device.

  • My Creative Cloud subscription has expired, and I assigned the monthly payment, but I can not open any progam creative cloud, I need help how to solve this problem

    my Creative Cloud subscription has expired, and I assigned the monthly payment, but I can not open any progam creative cloud, I need help how to solve this problem

    Carlos-
    Start by signing out and back in to see if it will see the subscription: 
    How to sign in and sign out of creative cloud (activate/deactivate)
    If the apps are installed fine and close after launch see this link:
    CC applications close immediately after launch
    If the problem is something different, please let us know the error you see or what is happening on the screen so we can advise  you on a solution
    Pattie

  • FREE TRIAL ON PAGEMAKER INSTALLED, BUT REQUIRES STUFFIT FOR FINAL STEP.  CAN'T SEEM TO MANAGE THIS STEP. NEED HELP MANAGING THE FINAL STEPS BEFORE PAGEMAKER IS USEABLE.  THANK YOU

    HAVE INSTALLED PAGEMAKER, BUT BECAME CONFUSED WHEN "STUFFIT" SEEMED TO BE REQUIRED FOR NEXT STEP.  NEED HELP IN FINAL STEPS IN DOWNLOADING PAGEMAKER FOR USE.

    >I would like to purchase a new mac with the appropriate operating system that will
    run pagemaker 7.  If not, I understand that my current mac, Mac OS X, version
    10.6.8, processor 2.8 GHz Intel Core i7, Memory 4GB 1067 MHz DDR3 will not support
    either Pagemaker 7 or InDesign.  My question is what package can I purchase that
    will satisfy one or both of these needs?  Thank you for any guidance.
    R_Kelly  created the discussion
    "FREE TRIAL ON PAGEMAKER INSTALLED, BUT REQUIRES STUFFIT FOR FINAL STEP. 
    CAN'T SEEM TO MANAGE THIS STEP. NEED HELP MANAGING THE FINAL STEPS BEFORE PAGEMAKER
    IS USEABLE.  THANK YOU"
    To view the discussion, visit: https://forums.adobe.com/message/6607524#6607524
    >

  • ESW-520-24P - New GUI?

    We're testing out the ESW series to replace the existing small business series for many of our customers. I was disappointed to see it run the same GUI as the SFE and SGE series switches! It's so clumsy and takes 10x as long to configure. And yes, we modify the clumsy config file offline but it's not that straight forward and always results in some type of error.
    Anybody know when the ESW series switches will run the new GUI that the SF 300-24P new small business series runs? I gotta say, I'm very impressed with that GUI as it seem to collapse all the best features of all 3 previous GUI's together.
    For now, we will plan on sticking with the SF 300 series until the ESW has the updated GUI.
    Thanks
    -robert

    Hi Robert,
    I also really like the new look and feel of the new 300 series.
    We are trying to use a standard look and feel for the GUI on the small business products.
    So the Small Business  Routers, WAPs.Switches, Security appliances  that are coming online and are online for sale at the moment,  all have the  same look and feel.  I think the ESW switch, because it is really only used on UC5XX will stay the way it is, I have heard no mention of upgrading it's GUI.
    Anyway currently, the ESW family of switches  has an advantage of being managed by Cisco Configuration Assistant (CCA).
    Robert, for other folks that look at this posting,  I will include a link below to the newer 300 series product comparison pages.
    As you will have noticed already, the 300 series is generations ahead of the older  SRW series switches, even allows for Layer 3 routing between VLANs.
    But for consistency of changeover from old part to new part , if you ordered in the past a part number  SRW224G4,   the 300 series replacement is now SRW224G4-K9-XX  (where XX can be UK  NA  EU.......... country code of some kind.)
    http://www.cisco.com/en/US/products/ps10898/prod_models_comparison.html
    regards Dave

  • Creating a VLAN on a ESW 520 PoE Switch

    Hi,
    we have two Catalyst Express 500 switches and a ESW 520 just purchased. the VLAN on the other two is 2. how do I change the Default to be 2 instead of 100 in the ESW Switch.

    Hi Prasanga,
    Just to clarify, are you trying to change the Voice VLAN, or Management VLAN?
    The Voice VLAN by default on the ESW is 100, and Management VLAN is 1.
    Thanks!
    Dave

  • Phone is locked/disabled (cannot remember passcode) but cannot restore becasue itunes says i need to turn off find my phone on icloud but i can't get into my phone to do that, HELP

    Phone is locked/disabled (cannot remember passcode) but cannot restore becasue itunes says i need to turn off find my phone on icloud but i can't get into my phone to do that, HELP

    Follow the directions here to force the phone into recovery mode & restore it:
    http://support.apple.com/kb/HT1808
    This will remove the passcode.

  • Tried to update iPhone 4 with iOS7, now it is frozen with an iTunes icon and the recharger icon. I can't get into anything.  Restarting hasn't helped

    I tried to update my iPhone 4 with the new Apple iOS7.  Now my phone is locked with an iTunes icon and my recharger icon.  I can't turn it on or get into anything.  I can't even receive calls on my phone.  HELP!

    Same thing happend to my Girlfriend, you will have to connect to the computer and snyc with iTunes. Make sure you update your iTunes software. we had to click on "Restore iphone...". phone updated and she lost everything on phone , we then tried to get everything back and only thing we got was her apps . Good luck hope everything turns out better then us. .

  • Can't Figure This Out....Need Help.

    I am attempting to add a line score from a minor league
    baseball team to a website of mine (it's an actual "in progrss"
    line score that updates itself). It looks like it uses a feed of
    somesort with a page refresher, but I can not identify what it is
    from looking at the source code.
    The format I really want looks like this website:
    http://web.minorleaguebaseball.com/clubs/ip_index.jsp?sid=milb&cid=t525
    However, I would be more than happy to get something that
    looks like the line score from this website (on the right above the
    standings):
    http://www.clippersbaseball.com/
    Any insight would be appreciated. Thanks in advance.
    MC

    you might want to explain what your problem is in the title
    of your post. a lot of people don't even look at ones that say
    something like "need help" without any explanation of what the
    actual problem is.
    that being said, from what i can tell from the code of those
    pages, it looks they created some kind of database or something for
    those stats thingies. which means it's probably not something that
    you can just copy and implement on your own site. you might have to
    create your own database.
    but maybe someone else will have some ideas. again, you might
    want to repost or change the name of this thread, if that's
    possible. i doubt you'll get many more responses to this
    one.

Maybe you are looking for