Can't create a new network

Hi,
I installed my airport express software and configured my system to connect via airport to my DSL internet service using DHCP. I'm now connected to the internet wirelessly, but the airport setup assistant won't allow me to create a new network so that I can print wirelessly. It tells me that there's an error with my airport extreme card and that I need to make sure it's installed correctly. What am I missing?
Thanks,
Stew

Do you have another wireless base station? If so, simply configure the AirPort Express (AX) following the directions in KB 302153, AirPort Express: How to join an existing wireless network in client mode.

Similar Messages

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.

Help, I cannot connect to the internet via airport with either my Imac or I-Pad. Connecting via ethernet works okay for Imac. I can connect wirelesssly with my windows laptop. I have reset my router, created a new network. It was all okay on Monday

Normally I have my IMac, I-Pad and Windows Laptop all working on my home network via wi-fi. This week I find that I cannot access the inetrnet on my IMac or I-pad via wi-fi but I can connect to the internet via wi-fi with my windows based laptop.
The airport diagnostics (reds/yellows) indcate that I am connected
I can access the internet if I plug my IMac into the router via an ethernet cable
I have restarted the IMac and the I-Pad, rebooted the router and created a new network. None of these changes has made a difference. Does anyone have any ideas please?

You have not completed your profile so we cannot assist you. In your profile you will indicate critical information such as what version of OS X is installed on your computer and the computer's configuration. If you do not know how to complete your profile please click Profile Update

Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi ?

Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi or simply solve this, I have tryied shotdown pressing keys like P and R, option, etc. Please help me .

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

TS2756 How can i create a new usb connection (service) on my iMac for sharing internet from my iPhone5 ( i seem have to deleted it )

How can i create a new usb connection (service) on my iMac for sharing internet from my iPhone5 ( i seem have to deleted it )
i know its not a problem whit my carrier o data plan or sharing preferences on the ipone because when i use it un my laptop it works perfectly through
the usb and even works on the Imac through wifi and bluethood tethering but NOT through usb!!.
the problem is that trying to make it work i deleted the "profile" usb iphone on the network prefereces panel. Now i only have 3 options: ethernet / wifi / bluetooth
but not the usb iPhone i used to have.
And when i try to add a new one i dont get a USB option.
can some one help me please??
this is how it looks (after the bluetooth PAN i used to have USB iPhone option)

The question would be more appropriate in the Mac forums as it is not really related to the iPhone.

How can I create a new TC backup with ethernet, so I don't have to wait two days for a new wireless backup?

How can I create a new TC backup with ethernet, so I don't have to wait two days for a new wireless backup?
Several times in the last year, I've gotten a message that Time Machine needs to completely redo my backup. Using the wireless connection, this takes almost two days. Is there a way to do the backup with ethernet and then switch back to wireless? Thanks.

May I know what is needed to make sure the MacBook is able to see Time Capsule on ethernet?
Connect an Ethernet cable from one of the LAN <-> ports on the 2Wire gateway to the WAN port (circle of dots icon) on the Time Capsule.
If AirPort Utility cannot "see" the Time Capsule now, you will need to perform a "hard reset" by holding in the reset button for 7-8 seconds or so and then reconfigure the Time Capsule. You can use the same Time Capsule name and password, etc. as before.
Configure the Time Capsule to "Create a wireless network" and select the Bridge Mode option when it appears during the setup using AirPort Utility.
Once the Time Capsule is configured, restart the entire network again. Power down everything, start the 2Wire first and then start each other device after that one at a time about a minute apart.
Now you can connect your Mac directly to one of the LAN <-> ports on the Time Capsule for the backup using another Ethernet cable. In general, about 20-25 GB per hour will transfer.
The Time Capsule will broadcast a much faster wireless network than the 2Wire can provide, so you might want to leave the setup "as is" for awhile after the first backup is complete. If you decide to use the Time Capsule as your main wireless access point, you would want to turn the wireless off on the 2Wire since two wireless networks in close proximity can create interference problems.
Or, if you want to use the wireless on the 2Wire, you could turn off the wireless on the Time Capsule. Then backups will occur over the 2Wire wireless, or over Ethernet.
I don't really recommend the "Join a wireless network" setting on the Time Capsule for most users, but you could go back to that setup as well if you want after the first backup is complete.

How can I create a new pattern?

How can I create a new pattern?

Sorry but is this doesn't appear to be a question about Apple Remote Desktop, Apple's software for managing networked Macs and the topic of this forum. I'd suggest you post in the forum for the version of Mac OS X you're running.
Regards.

Can't create a wireless network without a wireless card on my Mac

Help!
O.k. I tried searching the forums for an answer but the odd nature of my problem, and the immense database of topics made it very difficult to find a similar post.
The general issue/idea:
Run a wireless network using Airport Extreme - Connect desktop mac via ethernet and Roku player via wi-fi. Can't get the desktop mac to connect via ethernet when I restart the network/Airport Extreme.
My Father in law has my old computer; It's a PowerMac G5 (Dual 1.8GHz CPUs) running OS 10.5.8), connected to internet via cable (TimeWarner) modem. It does NOT have an Airport or Airport Extreme card installed. The computer works fine, and I don't believe that I 'need' an Airport Card in order to use the Airport Extreme (it's a brand new/refurbished model) in the manner described below.
I would like to use the Airport Extreme to generate/run a wireless network (Do I need an Airport Card in order to generate/run a wireless network? Doesn't the AE actually do that?), connect the desktop Mac to the network via Ethernet (I shouldn't need an Airport Card to do that, should I?) and connect a 'Roku Player (802.11g capable) to the network via wi-fi.
As far as I know, this should be possible.
Basic steps/as I understand them:
A. Connect ethernet from cable modem to AE.
B. Connect ethernet from AE to desktop Mac.
C. Create the wireless network using desktop Mac and Airport Utility.
D. Restart AE to start the wireless network running.
E. Connect Roku to wireless network over wi-fi.
I have no problems with A & B. Once the AE is connected to the desktop Mac, I'm able to get internet via ethernet as it passes through the AE. I can then create a wireless network (step C.) using the Airport Utility (and setup assistant). The problem starts after I've configured the wireless network.
Once I've configured the wireless network, the Airport Utility software prompts me to restart the AE in order to start the wireless network.
As soon as I restart the AE, my desktop Mac tries to connect to the 'wireless' network, even though it's already connected via ethernet. I don't have a wireless card in the Mac, and I don't want to connect the desktop using wi-fi/wireless. It's connected via ethernet, works fine during configuration, and I don't ever anticipate a desire to connect the desktop via wi-fi.
No matter what I do, I can't get the desktop to connect via ethernet. The only network connection option I'm offered is 'Rescan'. O.k. the desktop can't find the wireless network (because it doesn't have a wireless card), and I'm unable to continue with the Airport Utility. I can't make any further changes to the network (the options to manually change the network configuration are not available as the desktop Mac cannot currently talk to the AE - It's still trying to connect wirelessly), and the desktop has no internet connection as it's trying to connect wirelessly.
*How can I...*
*Setup/run a wireless network, while keeping the desktop Mac connected via ethernet?*
I'm perfectly willing to factory reset the AE and start over.
Any help appreciated.
Thwarted by the network.
- Robert

My Father in law has my old computer; It's a PowerMac G5 (Dual 1.8GHz CPUs) running OS 10.5.8), connected to internet via cable (TimeWarner) modem. It does NOT have an Airport or Airport Extreme card installed. The computer works fine, and I don't believe that I 'need' an Airport Card in order to use the Airport Extreme (it's a brand new/refurbished model) in the manner described below.
That is correct, you could connect the PowerMac G5, via Ethernet, to the AirPort Extreme Base Station (AEBS) or any other wired router for Internet access. You do NOT need an AirPort Card for wired access ... ONLY if you want the G5 to connect to a wireless network.
I would like to use the Airport Extreme to generate/run a wireless network (Do I need an Airport Card in order to generate/run a wireless network? Doesn't the AE actually do that?)
That is correct, the AEBS is a wireless router that can provide a wireless network. The AirPort Card, on the other hand is a wireless adapter used to allow a Mac to connect to a wireless network, created by any wireless router ... not just those provided by Apple.
As far as I know, this should be possible.
Basic steps/as I understand them:
A. Connect ethernet from cable modem to AE.
B. Connect ethernet from AE to desktop Mac.
C. Create the wireless network using desktop Mac and Airport Utility.
D. Restart AE to start the wireless network running.
E. Connect Roku to wireless network over wi-fi.
Yes, these are all good assumptions.
As soon as I restart the AE, my desktop Mac tries to connect to the 'wireless' network, even though it's already connected via ethernet. I don't have a wireless card in the Mac, and I don't want to connect the desktop using wi-fi/wireless.
Do you actually have an AirPort Card installed in the G5 now? If so, then it might be possible that the "firing order" for network connectivity has AirPort at the top of the list under System Preferences > Network. Just change the order to have Ethernet at the top and disable AirPort to ensure that the G5 connects by Ethernet only.

Do i have to reconnect all of my wireless devices if i creat a new network

Do I have to reconnect all of my wireless devices if I creat a new network with my new Time Capsule?

Not exactly sure what you mean.. if you create a new network using the same SSID and security as the previous network used.. then no wireless devices will need reconnecting.. but if it uses a new ssid..or different security settings.. (SSID is wireless name in apple speak.. ) then all wireless devices will need to be reconnected to work..
Or you might mean that both device are running in parallel.. and that is also fine.. bridge the TC and turn off its wireless. .then all devices that can connect to the TC will be able to..
There are 100 ways to skin the cat.. without knowing what you mean.. I have no way to answer other than the elves.. who always say yes and no.

BUG: Access Connect Abort, when I create a new network profile.

Where can I report bugs?
My system is windows xp sp2 on X60.
I have been using AC-4.42(Access Connection) for a long time. And before, there is no problem when I added new network profile into it.
But yesterday, I wanted to add a new profile into it. I opened the "create profile" window and input the name of the new profile (I have two network adapters, wired and wireless. So by default, the both are selected. And I left the default selection unchanged.), then "Next". The 2nd window is about wireless config, I configured everything, then go on "Next", at this moment, an error occured and AC aborted with four error windows. The titles of those windows are "ACMainGUI.exe error" and "ACMainGUIWnd: ACMainGUI.exe".
Then I did it again, I opened the "create profile" window, and this time, in this (1st) window, I changed the selection of network adapter, besides inputing the name of the new profile. I only selected the wired adapter, and then "Next". Sadly, this time the 2nd(next) window did not appear(pop up) at all. Instead, those four error windows poped up one by one. AC aborted again.
I repeated the above operations many times, and everytime, AC aborted.
So I went to the online "support and download" to look for some updates about AC. And I found AC-4.52 with luck. After downloading and installing, unfortunately the problem still exists. AC-4.52 still aborts when I create a new network profile.
So now, what to do. I have no ways. I am expecting the developers could note this problem and fix it and give me a newer update as soon as possible.
Sigh...

I have exactly the same issue. Next to the actions mentioned by ixbm I have also fully uninstalled and reinstalled the AC-4.52, but this didn't help.
Any idea on how to solve, installing older version?
regards,
Bart

Time Capsule - Create a new network or join existing?

Hello Folks,
So I got my new 2TB Time Capsule and I was reading through the discussion forum on how to set thip up.
I already have wifi in my home and I was wondering if it would be a good idea to connect the TC to the existing wifi network or create a new one?
I have my Wii, a smart TV, a mac, a pc, a printer, 2 iphones and a tablet already using my exisitng wifi connection and it all works very well.
Ideally, I would like TC to use the exisitng wifi, but I did read a few comments that this may not provide the best performance and creating a new network would be a better option.
Appreciate your feedback.
Thanks,
Abzt.

Do not use join wireless network.. that is slow as slow.
Set the TC to bridge mode and plug it into the current router by ethernet.
Then you have a number of choices.. you can turn off wireless..
Or run a separate wireless network but nothing actually connects to it.
Or use roaming.. ie use the exact same name as present wireless.. same security same password.. and the TC can reinforce the existing wireless.. the best way to do this is in an area of the house that has poor wireless but you can run ethernet to it.. if it doesn't exist just use a standard ethernet patch lead 3 or 4M long and connect the TC there.

Setting up a time capsule without creating a new network.

I want to set up my time machine but without creating a new network. However, my current network doesn't allow to connect a router to the network. When I connect the energy cable to the time capsule it keeps flashing an amber light. When I open the AirPort is says that it didn't find the base stations of AirPort and will keep searching.

To setup a TC.. without creating a new network.. and current network doesn't allow a router to connect.. sorry you have just created a conundrum.. nobody can give you an answer to that. It is impossible to use the TC in that case. It is 100% only a network drive. You should get an external drive and plug it into the computer.
The only solution is to have two networks.. if the current network cannot be used even with a bridged TC.
As long as you have a Mac with both wireless and ethernet you can do it.
See instructions I have with all the screen shots near the bottom of this thread.
https://discussions.apple.com/thread/4817218?tstart=30

Applescript to create a New Network

Hi all!
I'd like to build an applescript to create a New Network on Mac OS 10.6.
The script should run on a computer without a screen, and I will interact with the Mac through a VNC application on an Ipad, which I already have. So I need to know that every time the IP address of the private network will be the same.
I'm very new to Applescript so i was wondering if you could give me some tip on how to start, I've been trying with no success since yesterday but I know it can't be that difficult!
thanks!

OK, that helps a little, but not a lot... I'm still not getting it - or maybe you're not...?
Is the machine local to the iPad - i.e. are they on the same LAN?
If the machines are remote then creating a new wireless network isn't going to help since you'd also need to configure your router for port forwarding, etc.
If the machines are on the same LAN, though, the iPad should be able to connect directly - without any internet exposure - so you don't need to create a new network. You should be able to just configure the wireless network with a specific, known IP address and connect to that... unless you don't have a base station...?

How can I create a new iCloud account for a familiy member having a new iDevice and reuse one of my aliases for it

Hi there,
I moved into iCloud from the very beginning and started with one iCloud account for me and my family, making use of email aliases for family members. Now the number of personal iDevices grows and I want to create a new and separate iCloud Account for my son. The pity is, that I reserved his full name already as alias address on my initial iCloud account. If I now delete this alias, can I create a new account with the former alias as new primary email address?
Or is there at least any transfer procedure supported for aliases between different accounts?
Thanks for your help, lauterbachj

Couldn't agree more... the folks who are getting penalized for this are the early adopters of .Mac/iCloud dating from the days when the only way to implement a "family" account was to use aliases. Now all my kids' / my wife's name aliases sit in my account, unable to move. I guess the good news is that if I delete them nobody else will get them, but this seems a pretty poor consolation.
Would it really be so difficult to implement a "move this alias to another iCloud account" option that requires the "sender" and "receiver" to exchange some sort of code to implement the transation in order to prevent fraud?

IPad2 and a new MacBook running Lion, Both Devices use the same Apple ID which is a Hotmail eMail id. Can I create a new iCloud eMail Id and use iCloud eMail and continue to use my Hotmail Id for my Apple Id and use it for iTunes, iCloud

I have an iPad2 and a new MacBook running Mountain Lion. Both Devices use the same Apple ID which is a Hotmail eMail id. Can I create a new iCloud eMail Id and use iCloud eMail and continue to use my current Hotmail Id for my Apple Id for iTunes, iCloud.
Note, I will use both Hotmail and iCloud eMail.

Welcome to the Apple Community.
In order to change your Apple ID or password for your iCloud account on your iOS device, you need to delete the account from your iOS device first, then add it back using your updated details. (Settings > iCloud, scroll down and hit "Delete Account")

Can't create a new network

Similar Messages

Maybe you are looking for