Can't create Internet connection to My Mac Using USB

Hey All,
Recently i bought a new Mini Router Huawei 4G LTE E5732 Router, it was connected easily using WI-Fi to my Mac (MacBook Pro Retina, 13-inch, Late 2013)
installed the latest update OS X Yosemite 10.10.2, I tried to be connected through the USB port on the Mac using USB connection in the Network option on the System preferences, but i was surprised that there is no such a choice !!
Please can anyone help me, it is affecting my job !

It was solved, Thanks to the Apple customer service
They advice me to go to this link and it solved everything after updating the App version installed for the Mini Router on my Mac
http://consumer.huawei.com/en/mobile-broadband/mobile-wifi/support/downloads/e53 72-en.htm

Similar Messages

[Solved]Can`t create internet connection

I`ve installed arch linux on my lenovo y550, but, because I was too sleepy to think yesterday so I didn`t configure the /etc/rc.conf and /etc/resolv.conf file (I installed from CD). All in all i`ve got neither wired nor wireless connection to the internet (everything works fine on windows 7, the same laptop). I think the problem is there are no proper drivers. After typing
/sbin/ifconfig
I only get the lo, no eth0. I`ve configured the web connection on my PC 2 years ago, the same router and web provider, but I didn`t have any problems then, so I guess it must laptop issue.
#lspci | grep -i net
06:00.0 Network controller: Intel Corporation WiFI Link 1000 Series
07:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01)
I tried the modprobe pcnet32 and modprobe tg3 and modprobe broadcom. In theory, 2.6.33 kernel should support the driver tg3 for BCM57780 (?? Maybe the information I`ve found is wrong??)
still no result. (I didn`t modify the /etc/rc.local with those modprobes yet).
Any Idea what should I do to get the web access?
I`ve found this post:http://bbs.archlinux.org/viewtopic.php?pid=774219
and I`m curious how to install the iwlwifi-1000-ucode without internet connection to get my wireless going.
Any help with either connection?
SOLVED:
thx karol for solution. add this in your /etc/rc,local
modprobe -r tg3
modprobe broadcom
modprobe tg3
and add dbus in daemons. Also, while installing archlinux, you can find iwlwifi 1000 series in additional packages on cd (necessary for wireless connection)
Last edited by Xyzk (2010-07-19 16:10:56)

the error i`ve been talking about:
::starting network
eth0:unknown interface: No such device
[FAIL]
::Mounting Network Filesystems [DONE]
there are drivers ofr linux on the producent webpage, http://www.broadcom.com/support/etherne … nk_k57.php
But I`ve got no idea how to access my pendrive from console. I can copy it to the HDD using PartedMagic liveCD, so I`m most likely going to try this. What`s funny, even though eth0 doesn`t work on parted magic using DHCP, wireless network works perfectly fine :]
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="pl_PL.UTF-8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Warsaw"
KEYMAP="pl"
CONSOLEFONT=lat2-16.psfu.gz
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=()
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="archlinux"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#Static IP example
#lo="lo 127.0.0.1"
#eth0="eth0 192.168.1.101 netmask 255.255.255.0 broadcast 192.168.1.1"
#INTERFACES=(lo eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#gateway="default gw 192.168.1.1"
#ROUTES=(!gateway)
#ROUTES=(gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
#DHCP
eth0="dhcp"
INTERFACES=(eth0)
gateway="default gw 192.168.0.1"
ROTUES=(!gateway)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network netfs crond)
Last edited by Xyzk (2010-07-10 17:42:02)

Is it possible to activate an ipad w/o an internet connection on a mac?

Is it possible to activate an ipad without an internet connection on my mac?
I have got a macbook pro with iTunes 10.1.2 (17) and an micro-sim card with a iPad 3G data plan, so I can use it directly with the iPad, but I have to activate the iPad at first.
I have NOT any internet connection on the macbook pro (because I am actually traveling). So do not recommend to go to the next Apple Store etc.
Thank you.

Chris CA wrote:
Yes.
Plug it in and sync it. I don't believe an internet connections required.
You can register it when you get an Internet connection.
I have NOT any internet connection on the macbook pro (because I am actually traveling
You cannot get a wifi connection anywhere? (hotel, library, airport, coffee shop, etc.)
Yes, I can. But it costs $30 for 10 MB (minimal use) at the hotel. Just to compare: a 3G data plan with 3GB traffic costs $50 monthly
Message was edited by: Goodkat

Internet connection sharing between Mac Mini and Imac G3- how?

Ok, I'm trying to connect my G3 Imac (running 10.4.8) to my Mac Mini (also running 10.4.8) but it just wont work.
I've turned Internet Connection sharing on on my Mac Mini, and set it to share the airport connection to computers connected using Built in ethernet.
Network (on the M Mini) shows
Built-In Ethernet is currently active. Built-In Ethernet has a self assigned IP address and may not be able to connect to the Internet.
Network (on the G3) shows
Built-In Ethernet is currently active and has the IP address 192.168.2.7. You are connected to the Internet via Built-In Ethernet.
When i try to go to a webpage on the G3 it fails stating, 'You are not connected to the Internet'.
I'm using a standard straight through ethernet cable, as I was told a while ago from apple support that it doesn't matter which u use, straight through or crossover.
Any help would be really appreciated
Macbook 2.0Ghz 2GB 80GB/Mac Mini 1.42Ghz 1GB 80GB/Imac G3 450Mhz 640MB 80GB Mac OS X (10.4.8)

OK after some playing about I can now manage to connect to the mac mini and vice versa to share files.
The iMac G3 now says it has an IP address of 192.168.2.18, and that it's connected to the internet via built-in ethernet. I've set configure IPV4 to Using DHCP.
Except it's not connected to the net.
If i select Using DHCP on the Mini it doesn't obtain an IP address, not even a self set one. So i've set a manual IP address on that, and everything shows up green. Airpot connected to the internet and Ethernet has an IP address of 192.168.2.30.
After reading some forums I set up firewall logging. The result is what happens on the Mac Mini when I use network diagnostics on the G3:
Feb 11 16:43:52 richard-xxxxx-mac-mini natd[394]: failed to write packet back (Host is down)
So I opened port 394 (not really knowing what i'm trying) but it had no effect.

How do i get an internet connection from my Mac to my iPad using a usb cable?

I have a Mac connected to the internet through a modem. However, i also want my iPad to share this connection through the usb cable. Is this possible? If not, is there any other way i can get my iPad to share the internet connection from my Mac?

It look like you can turn your mac into a hotspot and connect your ipad to it via wifi.
http://computers.tutsplus.com/tutorials/quick-tip-use-your-mac-as-a-wi-fi-hotspo t-and-more--mac-46462

Wireless Internet Connection Between a Mac Mini & a Notebook PC

A Mac Mini, A Notebook PC (OS: Windows XP Pro SP2), A LinkSYS Wireless-G Broadband Router (Model: WRT54G)
If the Mac Mini is connected to the cable moderm provided by the ISP through the router above. Can the Mac Mini share internet with the notebook PC? The Notebook PC has to be connected to the internet wirelessly.
Im wordering if it works or not as Im going to buy a Mac Mini.
If so...
What does the Mac Mini need?
What does the notebook PC need?
Im very new to MAC, I have looked through the discussion, but Im not sure if people's situation is the same as mine. Any help is much appreciated!

If the Mac Mini is connected to the cable moderm
provided by the ISP through the router above. Can the
Mac Mini share internet with the notebook PC?
The router in effect shares the internet connection to the Mac and the PC, neither computer needs to share the connection as they are clients connected to the router.
If so...
What does the Mac Mini need?
The Mac mini comes with an ethernet port which allows it to be connected to the router.
The new models now come with built in wireless so could connect to your wireless router wirelessly instead of by cable.
What does the notebook PC need?
If the Notebook PC comes with integrated wireless then nothing else is needed. If it doesn't then it will need a wifi certified 802.11g wireless card.
iFelix

Can you combine internet connections ?

I've heard that you can combine 2 internet connections in to one faster one, fisrst is this posible with the MacPro using the two gigabit ethernet ports on the back (MacPro Mid 2012)? To do this i've heard that you need a special Router, a Link Aggregation Control Protocol supported one which is about $500, but im not sure if that is the kind of router you need. Anyone who got experience in this who could help me ?
Thanks,

Your Mac Pro 65lb tower with dual Ethernet ports does indeed support Link Aggregation.
It requires a Router or Switch that supports Link Aggregation Protocol, which is an expensive industrial-strength device.
OS X Mountain Lion: Combine Ethernet ports
If you do not have enough of a "mix" of traffic from multiple sources, some readers have complained that their speedup was disappointing. At least in older versions, connections were made in a permanent virtual circuit fashion, assigning each connection to one side or the other, and not using the full bandwidth for a single connection. Fail-over is supported just fine.
This also begs the question of where do you get anything else to connect to, that runs at 2Gbits/sec. Most Internet connections can't go anywhere near that fast, so it will not improve your download speeds.
Are you doing a lot of local File Transfers? Fiber channel may be more appropriate to support a Network Attached Storage device.

Acrobat XI can't find internet connection

I have had Adobe CC subsciption for some time now, but recently my Acrobat stopped working. it says that it can't find internet connection. But all the other Adobe applications installed through the CC application manager are working fine.
I've had numerous chats with Adobe agents, and with my office's IT guys, and there has been no solution.
We use corporate anti-virus, firewall and proxy scrypts. I've had all Adobe links whitelisted that were given to me by the Adobe agents. The hosts file doesn't have any Adobe info. I've tried reinstalling n+1 number of times, with various options such as selected boot and such, and still no solution.
Why is it that all other Adobe applications installed under the CC work fine, but Acrobat doesn't?
It's sad that if one buys a subscription and loses internet, one would lose all the products as well. One should be allowed to work on the applications, internet connection or not.
Please help with this Acrobat that has created a circus for me here.

Have you also asked in http://forums.adobe.com/community/acrobat to find out if someone there has the same problem... and a solution?

Can not create the connection in the enrironment!!

hello,every one:
please see the following code:
          Environment *env = Environment::createEnvironment(Environment::OBJECT);
          Connection *conn = env->createConnection(userName,password,connectString);
try
//use the conn
          catch (SQLException &ex)
               env->terminateConnection(conn);
               Environment::terminateEnvironment(env);
               throw;//re-throw
          env->terminateConnection(conn);
          Environment::terminateEnvironment(env);
          Environment *ev = Environment::createEnvironment(Environment::OBJECT);
//the program stopped here,display i can not create the new connection
          Connection *cn = ev->createConnection(userName,password,connectString);
          ev->terminateConnection(cn);
          Environment::terminateEnvironment(ev);
I have terminated the connection and the environment,then why I can not create the
connection in the new environment?
I have tried several times,if you connect the same database as the former,then it
does not work,but if you connect a new database ,it can create the new connection!
plus:I don't want to use conection pool .
Can I have some method to solve the problem?
Please help me!
Thanks a lot in advance!
tony from China

Hi Tony,
This similar sample works perfectly fine for me. Can you
retry with this?
#include <iostream>
#include <occi.h>
using namespace std;
using namespace oracle::occi;
int main()
        Environment *env = Environment::createEnvironment(Environment::OBJECT);
        Connection *conn = env->createConnection("scott","tiger","inst1");
        try
        //use the conn
        catch (SQLException &ex)
                env->terminateConnection(conn);
                Environment::terminateEnvironment(env);
                cout<<ex.getMessage();
        env->terminateConnection(conn);
        Environment::terminateEnvironment(env);
        Connection *cn;
        Environment *ev;
        try{
        ev = Environment::createEnvironment(Environment::OBJECT);
        cn = ev->createConnection("scott","tiger","inst1");
        catch (SQLException &ex)
                ev->terminateConnection(cn);
                Environment::terminateEnvironment(ev);
                cout<<ex.getMessage();
        ev->terminateConnection(cn);
        Environment::terminateEnvironment(ev);
}Rgds
Amogh

I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! Why is this a problem and how can i repair it?

I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! Why is this a problem and how can i repair it?

"I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! ":
That is correct.
"Why is this a problem and how can i repair it?"
Becasue this has never been a feature of iphone/ipod/ipad. There is nothing to repair.

NEED HELP! can't create mysql connection in DW MX 2004

I re-format my computer last week and after reformatting i
install my PHP Triad and Dreamweaver MX 2004, but i can't create
mysql connection using DW wizard, i already follow the step:
1. create / manage site
2. choose document type
3. set up testing server ( i use php mysql @ localhost)
and when i create new connection (fill the hostname,
username, password, and select databases) it failed and show
message "unidentified error occur".
it never happen before (before i re format my computer).
can anyone help me how to solve this problem.
sorry for my bad english i came from Indonesia,
thx before
rgrds
zhastro

I re-format my computer last week and after reformatting i
install my PHP Triad and Dreamweaver MX 2004, but i can't create
mysql connection using DW wizard, i already follow the step:
1. create / manage site
2. choose document type
3. set up testing server ( i use php mysql @ localhost)
and when i create new connection (fill the hostname,
username, password, and select databases) it failed and show
message "unidentified error occur".
it never happen before (before i re format my computer).
can anyone help me how to solve this problem.
sorry for my bad english i came from Indonesia,
thx before
rgrds
zhastro

Can't share internet connection with iPad since installing Time Capsule

Until today, I've used Earthlink's DSL service with a Netopia DSL modem with an ethernet connection to my iMac through a Linksys WRT54G router. My iPads (1 & 2) have been able to simultaneously share the internet connection over wifi.
Today, I installed a Time Capsule and removed the old Linksys router. I'm still using Earthlink's DSL service with the same Netopia DSL modem, and I still have an ethernet connection to my iMac, but through the Time Capsule now. I can get online from the iMac without problems.
But my iPad can no longer connect as they did previously. When I try to visit a website using Safari on the iPad, I get the message, "The Internet connection s currently in use by another computer. Enter your DSL Account logon password to switch the Internet connection to this computer." If I enter the DSL account password on the iPad, I can get online, but then the iMac is knocked offline.
How can I go back to sharing the connection so that any of the devices can get online at the same time?

I found another thread right after I posted and seem to have solved the problem following the steps described there (plus a couple more).
https://discussions.apple.com/message/15758093#15758093

Can you create multiple connections in smartview? for PROD and DEV?

Hi,
We have a production and development hyperion planning. In Smartview, we have successfully connected to PROD but can we create another connection to DEV?
or do we keep replacing the URL?
thanks

I think from 11.1.2.2 onwards the ability to add servers in Shared Connection is removed and an enhancement is filed to have that ability.
You can use private connection to connect to different instances
http://DEV:19000/aps/APS for Essbase
http://DEV:19000/HyperionPlanning/SmartView HyperionPlanning
If you are on 11.1.2.3 you can create an XML file and use that as your Shared Connection
Essbase Labs: Smart View News
Regards
Celvin
http://www.orahyplabs.com

I can't get internet connection even after wi-fi set is done with cisco

I can't get internet connection even after wi-fi set up is done with cisco

Not sure what Cisco is but if you are having problems with your wifi this link might help
On the iPad... tap Settings / General / Reset / Reset NetworkSettings.
Or here is a link that might help http://support.apple.com/kb/TS1398

I can't download OS5 or, rather, iTunes does download it about 450 mb and then, a few seconds after it starts processing the file, I get the message that I am timed out and am recommended to check my internet connection. I am using 3g to download it.

I can't download OS5 or, rather, iTunes does download it about 450 mb and then, a few seconds after it starts processing the file, I get the message that I am timed out and am recommended to check my internet connection. I am using 3g to download it.

I don't know which country you're in, but in the US, carriers limit the amount of download for a single file when using 3G. Have you tried wifi?

Can't create Internet connection to My Mac Using USB

Similar Messages

Maybe you are looking for