Can't do ISAKMP & fixup protocol esp-ike. I need a work-around HELP

I have a pix where I have the "fixup protocol esp-ike" enabled. In this pix, I am trying to set it up as VPN Lan-to-Lan, so the first line I try is "isakmp enable outside", but as soon as I type it, it tells me
ISAKMP cannot be enabled since fixup protocol esp-ike is enabled. Please correct your configuration and re-issue the command
I read that NAT-traversal can perhaps fix this, but I already tried it. I typed "isakmp nat-traversal 3600" and it went OK. I then tried the "isakmp enable outside" again but it gave me the same error message
So I don't know what to do at this point
any help please?
thanks

No, PAT is not being used in my pix. Only NAT. My pix 506e acts as a NAT device.
I have read that the 2 commands aren't compatible, so I was asking if there is a work-around that someone can help me with?
thanks

Similar Messages

  • How can I buy or license InDesign CS4? (I need to work in CS4 for a client, even though I have a CC subscription.)

    How can I buy or license InDesign CS4? (I need to work in CS4 for a client, even though I have a CC subscription.)

    There's no way to buy CS4 any longer through official reseller channels. If you can get the work done in 30 days you can use a trial, which you can download at Download and Installation Help

  • G4 just replaced power supply , it powers up , but the screen is not on and the mouse and keyboard aren't on either. A few times the computer came on with screen working but then it froze up, can't do any type of reset cause of keyboard not working. Help!

    G4 just replaced power supply , it powers up , but the screen is not on and the mouse and keyboard aren't on either. A few times the computer came on with screen working but then it froze up, can't do any type of reset cause of keyboard not working. Help! Pressed pmu button already,  nothing ,..  Ppc g4 Mac

    Should I check the memory cards themselves? Reseat them?
    Yes.
    Memtest X or Rember to test the RAM.
    Reseat is also good.
    The iPhone 4 doesn't like USB 1.1 much.
    after the update the computer was working well, except for this freeze when ever I connect iPhone.
    I'd try USB 2.0 PCI. That's how I connect my iPhone 4s, and have connected all iPhones and iPods, to my G4.
    Never an issue.
    Can't say the same for USB 1.1.......
    The above (previous post) linked PCI card is cheap enough.
    Want cheaper, try this:
    http://www.amazon.com/Protronix®-5-Port-Controller-Card-Chipset/dp/B005JE2U82/re f=sr_1_2?ie=UTF8&qid=1337472141&sr=8-2
    The NEC chipset is the desired chipset, regardless of what OS the maker says is compatible.
    OS X has native NEC chipset USB support.

  • Downloaded ios6 to my ipod touch and lost all color when i select an artist or song how can i get to be blue again tried resetting did not work any help would be apprciated?

    just downloaded ios6 on my ipod touch and lost all color when I select an artist or song how can I get it to be blue again tried resetting did not work any help offered would be liked

    You need to restore.
    Everything should be on your computer, so you can just sync it back.
    iPod touch User Guide (For iOS 4.3 Software)

  • HT4199 I have a Netgear R6300 wireless router and a Yamaha RX-3020 A/V receiver. An app is available to run on an Ipad. I have to reboot every morning to get it all working. Can I just plug cat6 between them, when I do nothing works, please help

    Should I use a network switch and plug my Yamaha A/V receiver and Yamaha DVD into it, then into the wireless router? Then the net into the routers net port???

    HT4199 I have a Netgear R6300 wireless router and a Yamaha RX-3020 A/V receiver. An app is available to run on an Ipad. I have to reboot every morning to get it all working. Can I just plug cat6 between them, when I do nothing works, please help

  • Someone changed my mother's adminstrative password.  Now she can't update software or make changes.  How do you work around that?

    Someone changed my mother's administrative password, and that person can't remember what he changed it to.  How do I work around this? 

    You have to get the install disc that came with the computer and boot to it.
    Put the cd in and restart the computer. Hold down the C key and it will bo into the installer.
    Once in you can click on the top menu and select reset password. Click the user and reset the password.

  • I can't open iPhoto after yosemite upgrade - tried to reinstall, not working! Help!

    Hi
    Im new here so please bare with me if I've not included everything needed but I'm really struggling an after trying everything else on every other link I've found Im stuck!
    I installed Yosemite a few weeks back. I have tried everything I have read on forums etc... to try to get iPhoto to work but nothing is helping. What am I missing out?
    I upgraded iphoto in the ap store. I have tried uninstalling iPhoto as per advice from a other thread and when I re download it it still just has a grey screen with the circle going round an doesn't do anything. All I can do is force quit it.
    I have my photos backed up. Im not concerned about getting them or them being wiped from my machine. My theory was to uninstall it and reinstall it fresh as new and just start again. My photo library was huge (talking well over 100,000 photos) so thought it might take a while but left it overnight an still nothing. iMovie and other programs working fine after the update. I just now have nowhere to do quick edits and view my pictures.
    iMac (27-inch, Late 2009),2.66 GHz Intel Core i5,4 GB 1067 MHz DDR3
    How can I just start again an have a nice fresh iPhoto for me to upload my photos from my backup drive?

    Hi, Léonie,
    My iphoto is having the almost the same problem except that these are old iphoto files from 2010-2013... And I backed them up in external drive.
    So, after upgrading and letting it repairing, iphoto asked me to quit the application. I'm sure it could be open with older version of iphoto...
    Below is what I see step by step.  Please help, I've got quite a few years memories there... 
    THANK YOU VERY MUCH!

  • Can't install a font I need for work - please help! 10.4 ={

    Hello,
    So I am trying to install this font on my work computer, which is old and has os x 10.4.11 (tiger?). I have downloaded the TTF file onto the desktop. When I double click to install it, it says I need to choose an application and none of them I tried will work. I have a brand new macbook myself and downloaded the same font - worked fine because I could put it right into font book.
    The problem here is that I cannot find font book anywhere on this computer and have not found any helpful discussions on how to re-install it or about different ways to get this font downloaded and usable. I have tried everything I can think of. I would just make these damned brochures on my own computer, but then they won't convert to this one.
    Anyways, super frustrated - any advice/places to get font book/or something else I could use would really help. I don't even care if it's a round-about way of doing it, I just NEED this font!!
    Thanks ahead of time!

    Is the font compatible w/Tiger?
    The Font Book is inside the Applications folder.  If it is not there, use Spotlight to search for it.  If Spotlight cannot find it, you can custom install Font Book directly from the system DVD that originally came w/your MBP. Use the custom install option.  It should be inside the Bundled Software folder.  If not, there, it will be inside the Applications folder. 

  • FWSM 2.3 "fixup protocol rtsp" security question

    Hi all,
    We've recently implemented SonicFoundry's Mediasite system on campus and are having an interesting problem. It's a media content streaming solution (Mediasite) that uses RTSP.
    A percentage of users external to the University cannot view the video streams, but a lot of others can. When testing, using our own external DSL connection, I also cannot view the video streams (same result from home using my personal DSL connection). After spending hours scanning packet-captures and knowledgebase articles I discovered that the inspection of RTSP packets - actioned because of the "fixup protocol rtsp" command in the FWSM 2.3 - could be the cause of the problem.
    I switched this feature off and I was then able to view the streams from off, and on, campus.
    My concern is this: being not overly experienced with the firewall, is turning off this inspection of RTSP leaving us open (or vulnerable) to anything else?
    The organisation is pushing to turn off the protocol inspection, but I want to have a basic understanding of the security or functionality ramifications before I allow this to happen.
    I've read the doco that I could find on Cisco.com but I find I'm still somewhat in the dark. As usual, all help greatly appreciated.
    Cheers,
    Ben Johnson

    The fixup rtsp command lets PIX Firewall pass RTSP (Real Time Streaming Protocol) packets. RTSP is used by RealAudio, RealNetworks, Apple QuickTime 4, RealPlayer, and Cisco IP/TV connections. PIX Firewall does not support multicast RTSP.
    Firewall Services Module Frequently Asked Questions :
    http://www.cisco.com/en/US//products/hw/modules/ps2706/products_qanda_item09186a00801e9e26.shtml

  • Unexpected Broker Exception: [can not close un-opened protocol] ???

    Hi,
    Has anyone seen this problem in the log file.... It occurred during a shutdown of the broker... Is it something I need to worried about?
    Broker Startup Info:
    ================================================================================
    Open Message Queue 4.3
    Sun Microsystems, Inc.
    Version:  4.3  (Build 7-g)
    Compile:  Fri Nov  7 19:11:27 PST 2008
    Copyright (c) 2007 Sun Microsystems, Inc.  All rights reserved.  Use is
    subject to license terms.
    ================================================================================
    Java Runtime: 1.6.0_07 Sun Microsystems Inc. /usr/jdk/instances/jdk1.6.0/jre
    [30/Jan/2009:11:45:08 MST] Syncing message store: false
    [30/Jan/2009:11:45:08 MST]    IMQ_HOME=/opt/openmq/mq
    [30/Jan/2009:11:45:08 MST] IMQ_VARHOME=/opt/openmq/var/mq
    [30/Jan/2009:11:45:08 MST] SunOS 5.11 amd64 vdev3th (4 cpu) root
    [30/Jan/2009:11:45:08 MST] Max file descriptors: 65536 (65536)
    [30/Jan/2009:11:45:08 MST] Java Heap Size: max=933888k, current=253184k
    [30/Jan/2009:11:45:08 MST] Arguments: -loglevel DEBUGHIGH -force -passfile /var/svc/profile/openmq.passfile
    [30/Jan/2009:11:45:08 MST] Initializing ClusterDiscoveryService
    [30/Jan/2009:11:45:08 MST] [B1004]: Starting the portmapper service using tcp [ 7676, 50, * ] with min threads 1 and max threads of 1
    [30/Jan/2009:11:45:08 MST] [B1060]: Loading persistent data...
    [30/Jan/2009:11:45:08 MST] Using built-in file-based persistent store: /opt/openmq/var/mq/instances/imqbroker/
    [30/Jan/2009:11:45:08 MST] attempting to set Message Bytes Limit to 10240K for destination mq.sys.dmq [Queue]
    [30/Jan/2009:11:45:08 MST] attempting to set Message Count Limit to 1000 for destination mq.sys.dmq [Queue]
    [30/Jan/2009:11:45:08 MST] Loading Stored destination mq.sys.dmq [Queue] connectionUID=null
    [30/Jan/2009:11:45:17 MST] [B1007]: Stopping Service jms with protocol tcp(host = *, port=0, mode=dedicated)
    [30/Jan/2009:11:45:17 MST] Exception shutting down  protocol, ignoring since we are exiting:
    java.io.IOException: Unexpected Broker Exception: [can not close un-opened protocol]
            at com.sun.messaging.jmq.jmsserver.net.tcp.TcpProtocol.close(TcpProtocol.java:353)
            at com.sun.messaging.jmq.jmsserver.service.imq.IMQIPService.stopService(IMQIPService.java:292)
            at com.sun.messaging.jmq.jmsserver.service.ServiceInfo.stop(ServiceManager.java:664)
            at com.sun.messaging.jmq.jmsserver.service.ServiceManager.stopService(ServiceManager.java:307)
            at com.sun.messaging.jmq.jmsserver.service.ServiceManager.stopAllActiveServices(ServiceManager.java:430)
            at com.sun.messaging.jmq.jmsserver.BrokerStateHandler$ShutdownRunnable.shutdown(BrokerStateHandler.java:483)
            at com.sun.messaging.jmq.jmsserver.BrokerStateHandler$ShutdownRunnable.run(BrokerStateHandler.java:383)
            at java.lang.Thread.run(Thread.java:619)
    [30/Jan/2009:11:45:17 MST] Session: Resuming Session [5282756623254863360][0]Consumer.java: resuming after detatch Consumer - Q:temporary_destination:__queue_10.80.165.6_65423_1:[consumer:5282756623254870016, type=CLIENT_ACKNOWLEDGE]
    [30/Jan/2009:11:45:17 MST] JMX Connector Server jmxrmi stopped successfully
    [30/Jan/2009:11:45:17 MST] Cleaning up transactions on connection IMQConnCLOSED,[email protected]:65423,admin:44113
    [30/Jan/2009:11:45:17 MST] Destroying temp destination Q:temporary_destination:__queue_10.80.165.6_65423_1 on connection death
    [30/Jan/2009:11:45:17 MST] [B1159]: Destination temporary_destination://queue/10.80.165.6/65423/1 [Queue] has been destroyed
    [30/Jan/2009:11:45:17 MST] WARNING [B2181]: Removing 1 messages associated with destination temporary_destination://queue/10.80.165.6/65423/1 [Queue]
    [30/Jan/2009:11:45:17 MST] Cleaning up transactions on connection IMQConnCLOSED,[email protected]:65423,admin:44113
    [30/Jan/2009:11:45:17 MST] [B1066]:   Closing: [email protected]:65423->admin:44113 because "[B0061]: Client exited without closing connections". Count: service=0 broker=0
    [30/Jan/2009:11:45:17 MST] closed connection IMQConnDESTROYING,[email protected]:65423,admin:44113:
    java.io.IOException: [B4117]: Unexpected Broker Exception: [destroyed Connection]
            at com.sun.messaging.jmq.jmsserver.service.imq.IMQIPConnection.writeData(IMQIPConnection.java:1563)
            at com.sun.messaging.jmq.jmsserver.service.imq.IMQIPConnection.process(IMQIPConnection.java:631)
            at com.sun.messaging.jmq.jmsserver.service.imq.OperationRunnable.process(OperationRunnable.java:170)
            at com.sun.messaging.jmq.jmsserver.util.pool.BasicRunnable.run(BasicRunnable.java:493)
            at java.lang.Thread.run(Thread.java:619)
    [30/Jan/2009:11:45:18 MST] [B1048]: Shutdown of broker complete.
    [30/Jan/2009:11:45:18 MST] Broker exiting with status=0 because [B1199]: Shutdown Requested by adminIf more detail are needed, please ask and I will supply whatever is necessary...
    Thanks.
    -Howard
    Edited by: Turret on Jan 30, 2009 1:10 PM

    Hi Tom,
    Thanks for the quick response!
    I am glad to hear that the log level is the reason for the output and not an issue with the broker!
    Thanks again....
    -Howard

  • Can't create SAPEvent SapRfc protocol: java.lang.reflect.InvocationTargetException

    "DEBUG 04 Feb 2003 12:37:26,443 BEA_SAP_1_0.EventGenerator - setUpNewTypes ->
              INFO 04 Feb 2003 12:37:26,463 BEA_SAP_1_0.EventGenerator - event generator worker thread com.ibi.beasap.event.EventGenerator@52e928 received the following new event types from the event router: com.bea.wlai.common.EventDefinition@927580e7,
              DEBUG 04 Feb 2003 12:37:26,714 BEA_SAP_1_0.EventGenerator - setUpNewTypes: new PushHandler created.
              ERROR 04 Feb 2003 12:37:28,036 BEA_SAP_1_0.EventGenerator - ERROR [manager] can't create SAPEvent SapRfc protocol: java.lang.reflect.InvocationTargetException
                   stacktracejava.lang.reflect.InvocationTargetException: java.lang.NoClassDefFoundError: com/sap/mw/jco/JCO$ServerExceptionListener
                   at java.lang.ClassLoader.defineClass0(Native Method)
                   at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
                   at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:106)
                   at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:390)
                   at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:152)
                   at java.lang.ClassLoader.loadClass(ClassLoader.java:294)
                   at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
                   at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
                   at java.lang.Class.forName0(Native Method)
                   at java.lang.Class.forName(Class.java:115)
                   at com.ibi.edaqm.XDSapRfcManager.getSapAdapterServer(XDSapRfcManager.java:33)
              

    "DEBUG 04 Feb 2003 12:37:26,443 BEA_SAP_1_0.EventGenerator - setUpNewTypes ->
              INFO 04 Feb 2003 12:37:26,463 BEA_SAP_1_0.EventGenerator - event generator worker thread com.ibi.beasap.event.EventGenerator@52e928 received the following new event types from the event router: com.bea.wlai.common.EventDefinition@927580e7,
              DEBUG 04 Feb 2003 12:37:26,714 BEA_SAP_1_0.EventGenerator - setUpNewTypes: new PushHandler created.
              ERROR 04 Feb 2003 12:37:28,036 BEA_SAP_1_0.EventGenerator - ERROR [manager] can't create SAPEvent SapRfc protocol: java.lang.reflect.InvocationTargetException
                   stacktracejava.lang.reflect.InvocationTargetException: java.lang.NoClassDefFoundError: com/sap/mw/jco/JCO$ServerExceptionListener
                   at java.lang.ClassLoader.defineClass0(Native Method)
                   at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
                   at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:106)
                   at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:390)
                   at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:152)
                   at java.lang.ClassLoader.loadClass(ClassLoader.java:294)
                   at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
                   at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
                   at java.lang.Class.forName0(Native Method)
                   at java.lang.Class.forName(Class.java:115)
                   at com.ibi.edaqm.XDSapRfcManager.getSapAdapterServer(XDSapRfcManager.java:33)
              

  • OSB can support Real Time Messaging Protocol?

    Hi everyone:
    I have a question, OSB can support Real Time Messaging Protocol (RMTP) to transmit streaming of Audio and Video?
    Thanks in advance

    Knorrar,
    You can pass audio/video streams as binary data to OSB.
    Audio File / Binary / OSB
    Regards,
    Abhinav

  • I am trying to update my iPod but I can't until I sync it. However when i try to sync it a message pops up and says "Blythes iPod" can not be synced because a session can not be started with this device. What do I do? Help!

    I am trying to update my iPod but I can't until I sync it. However when i try to sync it a message pops up and says "Blythes iPod" can not be synced because a session can not be started with this device. What do I do? Help!

    https://support.apple.com/kb/TS1567
    Ah, it has been mentioned daily esp since iOS 5 / iTunes 10.5 but has always been there as an issue.
    Order of attempts:
    Repair the installers
    Uninstall EVERY Apple component (auto and manual)
    Services: Restart all 3 Apple items (AMS, Bonjour, iPod)
    I* always do the last almost, then launch iTunes, and only then connect iPod.
    IF you see a yellow alert in Devices and Printers or in Device Manager, then I could find NO WAY to fix or repair other than a clean OS. Something messed up the device driver support.
    If/when Windows asks "what to do when it detects iPod"? don't chose any default action, to me, based on hunch and 3 PCs, that seems to mess AMS up for some reason.
    Tried with Windows 7 64-bit Pro and Home Premium, and also Deve Preview 8 (which other than the inability to update iOS to 5.0 seems to run better -- except when it comes to AMS thing! so seems Apple is not on the same page writitng drivers.

  • Implementing UIApplicationDelegate protocol methods in NSObject class not working.

    Hi Everyone,
    I am new bee in iphone developement. I want to implement UIApplicationDelegate protocol methods in one of my NSObject class, how can i implement that help me please.
    I have mentioned the sample code what acutal i want to impelment.
    .h file
    @interface SmaplClass : NSObject <UIApplicationDelegate>
    .m file
    - (void)applicationWillResignActive:(UIApplication *)application
    - (void)application:(UIApplication *)application didReceiveRemoteNotification:(NSDictionary *)userInfo
    -(void)application:(UIApplication *)application didRegisterForRemoteNotificationsWithDeviceToken:(NSData *)deviceToken
    - (void)application:(UIApplication*)application didFailToRegisterForRemoteNotificationsWithError:(NSError*)error
    Want to implement the above methods is NSObject class to be implemented or used, its not working. Help me can do it.
    Please help me
    Thanks,

    I complete the above discussion with saying that it is better to implement the notification handling methods in your app delegate. If there are good reasons to not to do so, you have to implement the methods in another class, instantiate the class, and call the methods from the actual UIApplicationDelegate protocol methods in the AppDelegate object. This way you can remove the actual notification handling code from AppDelegate class.
    For example, suppose you implemented the methods in the class called Test. This is a sample code in the AppDelegate class:
    @implementation AppDelegate
    - (void)application:(UIApplication *)application didReceiveRemoteNotification:(NSDictionary *)userInfo
          Test *t = [[Test alloc] init];
         [t application: application didReceiveRemoteNotification: userInfo];
    @end
    Or you can create an association relationship between the AppDelegate and Test, so you do not have to create a new Test instance in each of the remote notification handling methods:
    @interface AppDelegate {
         Test *test;
    @end
    @implementation AppDelegate
    + (id)init {
         if (self = [super init]) {
              test = [[Test alloc] init];
         return self;
    - (void)dealloc {
         [test release];
         [super dealloc];
    - (void)application:(UIApplication *)application didReceiveRemoteNotification:(NSDictionary *)userInfo
         // No need to create a Test instance. You just forward the call from AppDelegate instance to test      // instance
         [test application: application didReceiveRemoteNotification: userInfo];
    @end

  • I can not pair my itouch with my mac book pro version 10.6.6 .. it seems that maybe my itouch is having trouble connecting as my mac seems to pair, then waits for my itouch and it never works. please help!!

    can not pair my itouch with my mac book pro version 10.6.6 .. it seems that maybe my itouch is having trouble connecting as my mac seems to pair, then waits for my itouch and it never works. please help!!

    I am not certain this will fix your problem but I suggest you assign the printer a static IP address.
    Using the printer's front panel, select Menu > Network > WLAN > TCP/IP > Boot method, and change it to "static". Provide a static IP address that is on your LAN's subnet.
    For example, if you are using an AirPort Extreme, you might give it an IP address of 10.0.1.100. If you are using a Netgear or Linksys router that defaults to issuing 192.168.x.x addresses, you might give it an address of 192.168.1.100. That way, the printer will always "reside at the same address" on your network. If your router has the ability, you should reserve that address so that the router does not attempt to assign it to another DHCP device.
    Then, go to System Preferences > Print & Scan, and delete your existing printer with the "–" (minus) button. Add it again, using the "+" (plus) button. In the window that appears, select the IP pane, and from the Protocol menu select "Line Printer Daemon (LPD)". In the Address field type the IP address you gave your printer.
    If all goes well the "Pring Using" field will detect the printer at that address and automatically select the appropriate driver. You will see something similar to the following screenshot ("name" can be whatever you decide, and "location" is optional):
    Click Add, then you can close System Preferences.
    There are other possible reasons your printer is "not responding" which could include wireless interference from competing wireless networks, but try this "static IP" method first. It should mitigate the problem.

Maybe you are looking for