Can't Enable Web Services on a M276nw printer

Hi,
I am having trouble enabling HP Web Services on M276nw printer. Whenever I hit the "Enable" button it either says "Can't connect" or the loading page stays on for so long (have waited for more than 15mins) that I have to cancel the process manually. The printer is connected to the internet via wireless connection and to a computer, from which it was set up - again wirelessly.
I have looked at the forums here and tried powering off the printer and then the wireless router and them powering everyting on again, tried connecting to different wireless networks, but still can't enable Weservices.
I tried manually setting up a IPv4 connection, but unfortunately when I access the printer throughits IP adress in a browser, I can't see this specific part of the screen (as referred to by several people on the forums) where I can input DNS server details. Obviously my IPv4 Configuration Menu does not have these options.
Does anyone have ideas how I can solve this problem?
Any help is appreciated!
Regards,
Xepo

Hi Shlomi,
Many thanks for getting back to me. I tried your solution, but unfortunately doesn't work for me again.
I set up the DNS like you advised and as shown in the attached screenshot. After trying to enable webservices, it gives it a couple of tries and then show connection error.
Do you have any other suggestions? Anything is appreciated
Regards,
Xepo

Similar Messages

Can not enable web services. printer on the network. default ip not connecting using auto ip

B210 - have tried resetting defaults . default IP address will not connect to network with auto IP had to set IP addrtess manually something similiar to the properties on the verzion hot spot. can not disable web services - never enabled.
no Primary or secondary DNS server. not sure if this is problem. can print ok thru network.
This question was solved.
View Solution.

Hey bobupton!
Try going into the printer's EWS and using Google's public DNS servers (8.8.8.8 and 8.8.4.4). It sounds like you know what you're doing so I skipped a few steps on how to get there but if you need more help with it let me know!
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Can't enable web services/eprint

For some reason my Hp6700 will not allow me to enable web services/e-print

dcousine,
The first thing I would try in this situation is a network reboot.
First, disconnect the power cord from the back of your router.
Next disconnect the power cord from either the back of the printer or the wall, without powering it off first.
Wait about 30 seconds and reconnect the power cord to your router.
Wait about another 30 seconds and plug the printer back in. It should boot back up automatically, but if it doesn't go ahead and press the power button.
Once everything is back up and running, try to enable ePrint.
If that doesn't work for you, let me know and I can give you some more steps to try.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Can't enable web services for groups (wiki) in WGM

I'm having trouble creating a wiki on my server. More specifically, in WGM, I cannot enable web services for a group. The pull-down menu is accessible, but the only option is "(None)."
I have users and groups set up in OD (they are not local).
I have a working default web page.
I have web services enabled in Server Admin.
I can create and access user blogs.
My user and group folders are on a raid drive instead of the main drive - I'm wondering at this point if there's a problem with a folder name or permissions. WGM just doesn't seem to recognize that there's a site on my server.

OK - wikid is failing to start.
2/5/09 1:36:17 PM com.apple.wikid[37723] Removing stale pidfile /var/run/wikid.pid
2/5/09 1:36:17 PM com.apple.launchd[1] (com.apple.wikid[37723]) Exited with exit code: 1
2/5/09 1:36:17 PM com.apple.launchd[1] (com.apple.wikid) Throttling respawn: Will start in 9 seconds
From the wikid error log:
2009-02-05 13:36:17-0600 [-] Log opened.
2009-02-05 13:36:17-0600 [-] twistd 2.5.0 (/System/Library/Frameworks/Python.framework/Versions/2.5/Resources/Python.app/ Contents/MacOS/Python 2.5.1) starting up
2009-02-05 13:36:17-0600 [-] reactor class: <class 'twisted.internet.selectreactor.SelectReactor'>
2009-02-05 13:36:17-0600 [-] twisted.web.server.Site starting on 8086
2009-02-05 13:36:17-0600 [-] Starting factory <twisted.web.server.Site instance at 0x2eb19e0>
2009-02-05 13:36:17-0600 [-] twisted.web2.channel.http.HTTPFactory starting on 8087
2009-02-05 13:36:17-0600 [-] Starting factory <twisted.web2.channel.http.HTTPFactory instance at 0x2eb1648>
2009-02-05 13:36:17-0600 [-] set uid/gid 94/94
2009-02-05 13:36:17-0600 [-] Traceback (most recent call last):
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/bin/twistd", line 21, in <module>
2009-02-05 13:36:17-0600 [-] run()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistd.py", line 27, in run
2009-02-05 13:36:17-0600 [-] app.run(runApp, ServerOptions)
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/app.py", line 379, in run
2009-02-05 13:36:17-0600 [-] runApp(config)
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistd.py", line 23, in runApp
2009-02-05 13:36:17-0600 [-] _SomeApplicationRunner(config).run()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/app.py", line 158, in run
2009-02-05 13:36:17-0600 [-] self.postApplication()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistdunix.py", line 213, in postApplication
2009-02-05 13:36:17-0600 [-] startApplication(self.config, self.application)
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistdunix.py", line 183, in startApplication
2009-02-05 13:36:17-0600 [-] app.startApplication(application, not config['no_save'])
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/app.py", line 400, in startApplication
2009-02-05 13:36:17-0600 [-] service.IService(application).startService()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/service.py", line 233, in startService
2009-02-05 13:36:17-0600 [-] service.startService()
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/service.py", line 62, in startService
2009-02-05 13:36:17-0600 [-] SettingsManager.globalSettings.rebuildIndex())
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/SearchManager.py", line 424, in buildAllIndexes
2009-02-05 13:36:17-0600 [-] buildSearchIndex(aPath, doRebuild)
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/SearchManager.py", line 406, in buildSearchIndex
2009-02-05 13:36:17-0600 [-] GroupSqliteIndex.buildSearchIndex(whichPath, forceRebuild)
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/GroupSqliteIndex.py", line 551, in buildSearchIndex
2009-02-05 13:36:17-0600 [-] con = sqlite.connect(indexDBPath, isolation_level=None)
2009-02-05 13:36:17-0600 [-] sqlite3.OperationalError: unable to open database file
I would like to fix this without reinstalling. If there's a way to restore this specific database file or any part of the wiki, I would prefer to do that. Does anyone have an idea what files I should check/restore?

Can't Enable Web Services HO Officejet 6700 Premium

Printer is connected to a home wireless network. Using the printer contorl panel set up it continues to say "update could not be downloaded". Hit Retry but always fails. Checked wirless connection and its working.
This question was solved.
View Solution.

I am trying to enable web services, and yes, i can print from the computer, finally.
thanks.
laur328

M451dn can not enable web service tab

I BOUGHT A NEW LASERJET PRO 400 M451DN
NETWORKED PRINTING WORKS PERFECTLY
TRYING TO ENABLE WEB SERVICE TAB AND SAYS "CONNECTION ERROR CHECK CONNECTION"
ITS ON MY DMZ SEGMENT WHAT DO I LOOK FOR?
THANKS IN ADVANCE FOR ANY HELP
JOHN

Hello,
The first thing I would do is follow step six in this document to set a static IP: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031&cc=us&dlc=en&lc=en&product=4023246&tmp...
When it askes for DNS information, enter in Google's DNS. Preferred DNS = 8.8.8.8 Alt DNS = 8.8.4.4
If the printer is on a corporate network, it may require a proxy to get an internet connection.
If that does not help, if you could provide me with the following information it would help me out. First, who is your ISP( Internet Service Provider, i.e. Comcast, AT&T, Verizon, ect.)? Second, who is the maker of your router? Lastly, what is the model number and firmware version of your router?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Officejet 6500a Plus - can't enable Web Services

Any help would be appriated on this - I've tried trawling Google to no avail!
I'm trying to enable Web services on my printer to use apps, ePrint, Airprint, e.t.c. When I press Web Services setup, I accept the terms and conditions and am instantly taken to a product update check. The screen then displays 'No product updates available for this printer' with only an 'OK' button to press, when I do I am taken back to the terms and conditions. I am stuck in a permanent loop! All other services (print, scan) work fine and the printer is definitely connected to the internet.
I have tried:
-Restoring factory defaults
-Turning off printer and router.
-Changing DNS settings for the printer.
Any other suggestions - I'm getting really frustrated now so would appreciate any ideas!!
This question was solved.
View Solution.

Hi dcdingo,
I’ve sent you a private message. I’ve included the link to How To Send A Private Message post as it also explains how to check for them if you are unsure.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Can't enable web services on LJ Pro 1102w

The printer is connected to the wireless network just fine but when I try to click Enable on Web Services I get an error "Connection Failed". Giving the printer a fixed IP address doesn't help and neither does adding to the public IP list.
Suggestions?

Hello cmerrill,
The first step I would try is power cycling the printer. You can do this by following these steps:
While the printer is still on, unplug the power cord from the printer, leave it unplugged for 30 seconds, then reconnect the power cord to the printer. Once plugged back in the printer should power on automatically.
Also, I would make sure the printers firmware is up to date. You can check by visiting the printers support webpage and selecting the Operating System you are using at:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?Product=4110396&lc=en&cc=us&dlc=en&lang=en&cc=us
Hope this helps.
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Can;t enable web service on HP Officejet Pro 8600 N911a

HP Officejet Pro 8600 N911a we have installed this printer as a network printer. Everything works fine except that I cannot enable the Web service to EPrint or scan to an email. It says the printer cannot access the internet.
This question was solved.
View Solution.

Hello. First power cycle the printer, and the router to see if that will clear up the error message. To do that unplug the router then power down the printer using the power button. Then plug the router back in and once it is back up an running, turn on the printer and try to reconnect to web services
Then, if still unable to connect, I would set a static DNS on the printer. To set a static DNS you must access the embedded web server (EWS). You do that by entering the IP address for the printer into the address bar of the browser of your choice.
Once it brings up your Officejet's EWS, locate the tab that is labeled “Network”. From there look in the left column on the new page that will pop up and select IPv4, wired or wireless will depend on how the printer is connected to the network. That will bring up the page to set the Static DNS. It will be the 2nd portion of that page.
Set the radial dial to manual. Then, for the Manual preferred/Primary DNS, set it to 8.8.8.8 and the Manual Alternative/Secondary to 8.8.4.4; then click apply.
NOTE: if another message with an option to click “OK” appears, read that message carefully. Most of the time it is an option to undo the change you just did and you will want to avoid clicking that message. Just navigate away from that page by clicking on another tab.
Power cycle the printer. Once printer is back up and through with calibrations from being turned off and on. Reattempt to connect to web services by touching the icon.
I am a former employee of HP...
How do I give Kudos?| How do I mark a post as Solved?

Unable to call WSS (WS-Security) enabled Web Service using UTL_DBWS

We are attempting to call a WSS (WS-Security) enabled Web Service from PL/SQL using the UTL_DBWS package (see [http://download.oracle.com/docs/cd/B19306_01/appdev.102/b14258/u_dbws.htm#CHDIDGJH] ). We are doing this in similar fashion to [http://www.oracle-base.com/articles/10g/utl_dbws10g.php] with calls to utl_dbws.create_service, utl_dbws.create_call and utl_dbws.invoke.
Using this method we can successfully call an unsecured Web Service, but calls to WSS-enabled Web Services fail. We are currently using Oracle Database 10.2.0.3.
The failure we are getting is:
ORA-29532: Java call terminated by uncaught Java exception: javax.xml.rpc.soap.SOAPFaultException:
com.sun.xml.wss.XWSSecurityException: Message does not conform to configured
policy ( AuthenticationTokenPolicy(S) ): No Security Header found;nested
exception is com.sun.xml.wss.XWSSecurityException:
com.sun.xml.wss.XWSSecurityException: Message does not conform to configured
policy ( AuthenticationTokenPlicy(S) ): No Security Header found
Apparently UTL_DBWS does not support calling WSS enabled services, although this doesn't appear to be an officially recognised position. Does anyone know if Oracle are planning to support this soon (if ever)? Looking at Re: Calling WS from PL/SQL using WS-security suggests that support has been considered before, but not yet realised.
Thanks,
Tom

Having raised a Service Request with Oracle support on this, I got the following response from Oracle Development (On unpublished bug [8542959|https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=BUG&p_id=8542959]):
Development has confirmed that WS-Security is not supported through UTL_DBWS. They have also acknowledged that this is not documented and they will change the official Oracle documentation will reflect this fact. From what is being stated, it would appear that there is no plan to support the use of WS-Security through UTL_DBWS in any release in the near future.
So, in short, without developing your own home-grown SOAP request, there is no way to call a WSS enabled web service from within PL/SQL.
-Tom

How to Remove & Re-Enable Web Services on LaserJet printers supporting ePrint

If your LaserJet printer has been disconnected from or failed to connect to Web Services, you may need to power cycle your printer to reconnect. If that does not resolve the problem, you can remove web services, wait 30 seconds, then re-enable web services to re-establish your connection to ePrint and Print Apps. Note: this last step will result in a new email address being assigned to your printer.
How do I remove HP Web Services for my LaserJet printer?
Print a configuration page from your product, and locate the IP address.
At your computer, open a Web browser and type the product IP address into the address line and press Enter. The HP Embedded Web Server opens.
Click the HP Web Services tab.
Select the option to disable Web Services.
How do I enable or re-enable HP Web Services for my LaserJet printer?
To use HP ePrint, you must first enable HP Web Services. Re-Enabling Web Services uses the same procedure as enabling the Web Services.
Print a configuration page from your product, and locate the IP address.
At your computer, open a Web browser and type the product IP address into the address line and press Enter. The HP Embedded Web Server opens.
Click the HP Web Services tab.
Select the option to enable Web Services.
When Web Services are enabled, ePrint information appears in the HP Embedded Web Server. Look for the e-mail address that is automatically assigned to the product. The product also prints an HP Web Services information sheet that contains this e-mail address and instructions
If you were unable to register your printer in www.hpeprintcenter.com within 24 hours of printing your information sheet, you must re-enable the printer code by reprinting your information sheet. The information sheet will also provide your email address if you have forgotten it.
How do I print the Web Services Information Sheet for my LaserJet printer?
You can only add the printer to your HP ePrintCenter account within 24 hours after printing the information sheet. You can re-print the information sheet at any time from the printer control panel.
Print a configuration page from your product, and locate the IP address.
At your computer, open a Web browser and type the product IP address into the address line. The HP Embedded Web Server opens.
Click the HP Web Services tab.
Click the Print Information Sheet button.
I am an HP employee.

To help improve the organization and information sharing in this forum this post/discussion has been closed and replaced.
Please see this post: <link to new “Enable Disable Web Services on your printer” post.
If after reviewing the post above you still have questions/issues with your web-connected printer, you can either review and comment in existing posts in this forum that report issues like yours, or if necessary start a new post requesting assistance.
Miles
HP Employee

Enable Web Service access for a Web service-enabled client

Hi,
I want to access data in Oracle CRM On Demand from a Web services-enabled client. The "Oracle Web Services On Demand Guide" suggest the Web Services Access should be granted by Customer Care representative. By default, this access is enabled for the Administrator role for new companies. However my admin account can't access web services from a web enable client.
Can anyone please suggest me the setting/step that i need to enable Oracle On Demand Web service access from a Web services-enabled client?
Note: I am new to oracle on demand so my query can be a silly thing.
Thanks & Regards
Ravish

I was able to resolve this issue. Actually, i was trying with trial account that don't allow the OCOD web service integration.

Calling a WSSE Enabled Web Service Through a Java Proxy Class

I am trying to create a client that can access a WSSE enabled web service through
the generated java proxy. For now all I am asking for in the .wsse file is the
username and password with the line <token tokenType="username"/>. In the client
I am setting the username and password token exactly as the BEA documentation
describes:
UserInfo ui = new UserInfo("myuser", "mypassword");
session.setAttribute(WSSEClientHandler.REQUEST_USERINFO, ui);
Yet I am getting the following error message when I try to run the client:
java.rmi.RemoteException: SOAP Fault:javax.xml.rpc.soap.SOAPFaultException:
EJB Exception: ; nested exception is:
com.bea.wlw.runtime.jws.wssecurity.exception.WLWWSSEException: Policy
requires Message to contain UsernameToken, UsernameToken not found in the Message.
Can anyone tell me what I am missing?
Thanks,
John

Hi John,
In your standalone client, use the following two properties to send a
user name and password to the service so that the client can
authenticate itself: javax.xml.rpc.security.auth.username
javax.xml.rpc.security.auth.password
See the docs [1]
Hope this helps,
Bruce
[1]
http://edocs.bea.com/wls/docs81/webserv/security.html#1073863
John H wrote:
>
I am trying to create a client that can access a WSSE enabled web service through
the generated java proxy. For now all I am asking for in the .wsse file is the
username and password with the line <token tokenType="username"/>. In the client
I am setting the username and password token exactly as the BEA documentation
describes:
UserInfo ui = new UserInfo("myuser", "mypassword");
session.setAttribute(WSSEClientHandler.REQUEST_USERINFO, ui);
Yet I am getting the following error message when I try to run the client:
java.rmi.RemoteException: SOAP Fault:javax.xml.rpc.soap.SOAPFaultException:
EJB Exception: ; nested exception is:
com.bea.wlw.runtime.jws.wssecurity.exception.WLWWSSEException: Policy
requires Message to contain UsernameToken, UsernameToken not found in the Message.
Can anyone tell me what I am missing?
Thanks,
John

I get an web service error when trying enable web services. I have latest update and rebooted

i get an web service error when trying enable web services. I have latest update and rebooted

hi there philnj,
could you help the community narrow troubleshooting by providing a little more information? Particularly what model printer are we dealing with?
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Please help Installed apex 4.1 on Oracle 11g Xe can't create web services

I went to Shared Components > Web Service references to create a web services reference using wsdl.
My webservices are local to my network.
I do not use proxy. Not using UDDI.
I enter my WSDL URL but error message is returned
The WSDL document was unretrievable because either the URL you supplied was invalid, your environment requires a valid proxy server address for HTTP requests and you have not defined one for this application, or a wallet needs to be configured for this instance of Application Express for HTTPS requests
All I see are
Amazon Web Services 3.0
Google API Beta
Q1. How can I register my wsdl url?
Q2. How were amazon and google registered?
Edited by: Oracle Primavera on Oct 4, 2011 5:29 PM

Ensure that you can ping the web services server.
Then check whether there is a valid/appropriate acl for the apex_040100 user;
select * from dba_network_acl_privileges where principal like 'APEX%';
Refer to Enable Network Services in Oracle Database 11g in the install manual.
~t

Can't Enable Web Services on a M276nw printer

Similar Messages

Maybe you are looking for