Can't extend my Apple Wireless network with Airport Utility 6

I have an Air Port Extreame and an Air Port Express and am trying to extend my network and since I upgraded to Air Port Utility 6 it will only let me join the network and not extend it. I can not find the option to allow this network to be extended anymore within 6 on the extreame. Is anyone else having this issue as well or am I just missing where to choose to allow my network to be extended like I did in 5?

It would be hard to say, at this point, if this option was "missed" or became "automatic" when another AirPort is configured to extend a wireless network. I would tend to agree with you that it is the former.
As you know this is a user-to-user community. Although Apple employees occasionally visit the forums, there is no guarentee that they would act on any of the suggestions users place here. Instead, you should submit your suggestion to the following Apple site.

Similar Messages

Can I extend AP Extreme Wireless network with my a TC and also use TimeMachine with it?

I currently have an Airport Extreme Base Station in my Home Office in the basement and would like to purhcase a TC to be placed upstairs to extend the Wireless Signal and also use it with TM to backup several apple computers.
Do I need to run a Network Cable from the AE in the basement to the TC unit or can I simply piggy back off the wireless signal produced by the AE? I can do either, but just want to make sure I get what i'm looking for.
I'm also running Apply TV in many rooms....will the TC unit produce a new wireless signal or extend the wireless already in the house. This is critical as Apple TV Units and the device connecting to it must be on the same network.
Thank you for your help in advance.
david

I currently have an Airport Extreme Base Station in my Home Office in the basement and would like to purhcase a TC to be placed upstairs to extend the Wireless Signal and also use it with TM to backup several apple computers.
That is doable.
Do I need to run a Network Cable from the AE in the basement to the TC unit or can I simply piggy back off the wireless signal produced by the AE?
Wired Ethernet cable connections are strongly preferred in setups like this, since there is no speed loss in a wire....and much less chance of an error occuring over a wired connection. The wireless signal produced by the Time Capsule will be much faster with a wired connection as well.
Wireless between the AirPort and TC might work.....IF....the Time Capsule is located where it can receive a really strong signal from the other AirPort, but at best, the speed will drop by about half when you do this.
I'm also running Apply TV in many rooms....will the TC unit produce a new wireless signal or extend the wireless already in the house. This is critical as Apple TV Units and the device connecting to it must be on the same network.
The TC will extend the existing network using either a wired or wireless connection.

Having trouble with extending an Apple wireless network with a AirPort Express

Trying to extend the range of my AirExtreme with a AirExpress:
I get stuck when the AirPort Utility ask is I'm sure I want to switch networks. if I select switch I loose the AirExtreme. If I select don't switch it take me back to the beginning. Any help will be appreciated.

You have to "switch" networks to be able to pick up the signal from the Express and configure it with new settings.
Once the Express is configured it will become part your existing network when you see a green light.
Then, switch back to your regular wireless network on your Mac and everything will be on the same network

Extend Linksys WRT160N wireless network with Airport Express

First off, I'm a network simpleton, so please keep that in mind!
I've seen similar posts, but I'm not sure definitively if this is possible. Trying to extend the wireless network from a linksys wrt160N with the airport. Is this possible without a phd in network engineering? If so, are there step by step instructions someplace that can help me?
I really appreciate any direction!

Welcome to the discussions!
I'm assuming that you are trying to do this using wireless only.
Apple's "extend a wireless network" feature will only work if both the main router and extending device are Apple "n" devices. Unfortunately, this feature is not compatible with devices from other manufacturers.

Extending my Linksys Wireless Network with AirPort Express

I would like to add an Airport Express to my wireless network to extend my wifi range and add AirPlay to my home theater system. Can Airport Express be used to extend my current wireless system that is not an Airport Extreme devise?
Also, by adding the Airport Express does this now limit the number of devices I can have on my wireless network to the 10 even if the Linksys supports 50?
Thanks for any advise...

Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your non-AirPort router can be extended wirelessly with the AirPort Express Base Station (AX).
The few that are known to work are:
another Airport Express Base Station
802.11g Airport Extreme Base Station (AEBS)
802.11n AirPort Extreme Base Station (AEBSn)
Linksys WRT54G or WRT54GS (not v5)
Belkin F5D7230-4 and F5D7231
BT Voyager 2091
Netgear WGR614 v6
Buffalo WGR-G54

Extend a E4200v2 wireless network with airport extreme

I have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2?
Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?
I can't stand the interface. The E4200v2 is brand new.

Before I suggest you for any trouble shooting steps, I would like to as few questions. Is you Linksys/Cisco router can able to access the Internet. If YES then try the following steps
1. After unpacking your Airport Extreme, connect the ethernet cable from your jack to the leftmost ethernet port on the back of the Airport. This is the WAN port marked with the small circular image. Next plug the AC adapter into the power port on the Airport and plug it into the wall.
2. Once the Airport Extreme has been plugged into the network and powered on, the status light on the front will go through a series of colored flashes. When the status light glows solid green, your Airport has been initialized and is connected to the network. This may take a few minutes. If your status light fails to glow solid green, please consult your manual for status light explanations.
3. Make sure the wireless card on your computer is enabled and turned on. Connect to your Airport Extreme, which will most likely appear as Apple Network followed by some letters.
4. Next install the Airport software from the included CD. After installation, launch the Airport Utility application. This is located in the Utilities folder in the Applications folder on a computer using Mac OS X, and in Start > All Programs > AirPort on a computer using Windows.
Please keep in mind that the Airport Utility is released with a new version every few months, so the screen shots you see below may not look exactly like what you see on your computer.
5. Select your base station, and then click Continue.
6. Enter a Wireless Network Name and a Base Station Name and click Continue. Write these names down for future reference.
7. Enter your Country and Radio Mode on the next screen. Using 802.11n (802.11b/g compatible) is the proper choice in most cases. Click Continue.
8. Select WPA2 Personal security on the next screen, then enter a Wireless Network Password and Verify it. This password must be between 8 and 63 characters. You should write this password down and keep it near your Airport Extreme in case you forget it. Click Continue.
9. Select "I connect to my local area network (LAN)" on the next screen and click Continue.
10. Leave the default settings (Using DHCP) on the next screen and click Continue.
11. If you are interested in connecting USB peripherals to your Airport, consult your manual for additional information. Otherwise leave the default settings and click Continue.
12. Enter a Base Station Password and Verify it. Write this password down and keep it near your Airport Extreme. You will need it if you ever want to modify any settings for your base station. Click Continue.
13. Click Update. Your Airport Extreme base station has been configured and will now restart. Quit the Airport Utility and connect to your new wireless network.
Check whether it helps you or not..

Extending a hidden wireless network with airport extreme

For some reason, I'm unable to get my second AEBS to extend the network of my primary AEBS.
Network Topology:
Internet =>
AEBS #1: Gen5 (tower) AEBS running v7.7.3 as my primary AP =>
=> Linksys 8-port Hub =>
LAN Devices
=> AEBS #2: Gen4 (flat) AEBS running v7.6.4 intended to extend the above network
Current Settings:
The AEBS #1 is configured as follows:
Create a wireless network
Do not broadcast the network name for either 2.4 GHz or 5GHz
Timed Access set with all MAC addresses established in the table including both AEBS's and both their frequencies
WPA2 Personal set
Router Mode: DHCP & NAT
The AEBS #2 is configured as follows:
Extend a wireless network
Do not broadcast the network name for either 2.4 GHz or 5GHz
Timed Access set with all MAC addresses established in the table including both AEBS's and both their frequencies
WPA2 Personal set
Router Mode: Off (Bridge Mode)
At this point, AEBS #2 cannot find the network I entered and suggests I select a network from the drop down. Of course, when I click the drop down, there is no network listed because AEBS #1 isn't broadcasting its network name.
So my question is this... will AEBS #2 actually extend the network of AEBS #1 under these circumstances or am I relegated to setting up AEBS #2 as creating another network with the same name, hidden but in bridge mode as above? The reason I would like to extend the network and not have two networks under the same name is because I believe its affecting device connectivity and performance.
Thanks...

Try unhide the name of the network on AEBS 1
Then, configure AEBS 2 to extend the network
Then, go back and hide the network on AEBS 1, then AEBS 2
The reason I would like to extend the network and not have two networks under the same name is because I believe its affecting device connectivity and performance.
We assume that you are configuring the AEBS 2 to extend using wireless. AEBS 2 must use the same wireless network name as AEBS 1 when it extends using a wireless connection. Not possible to use another wireless network name on AEBS 2 when it extends using wireless.
If AEBS 2 connects using Ethernet, then you can set it up with a different wireless network name. In that case it will not be setup to "extend a wireless network".....the correct setting would be "create a wireless network".
You must already know that there are a number of free utilities available on the Internet that will reveal a "hidden" network in seconds, and that anyone who wants to "see" your network can do so very easily. But, it's your call.

Extend Time Capsule Wireless Network with Airport Extreme

I tried to install two base stations in my house. The first one is the Time Capsule which I use as my main router connected to the DSL modem by Ethernet and which has the main wireless network. The second is an Airport Extreme Base Station which tries to connect wirelessly to Time Capsule to extend the wireless network. I use WPA2 Personal as a security mode and it says there is an error at the end when it reconfigures the Airport Base Station --- questions: does it normally work with these two devices in that order? What process to make it work?”

use Airport Utility manual set up button and place the secondary router in bridge mode then configure your wireless setting.

Extend existing wireless network with airport express..impossible?

I have tried to extend my existing wireless network with an airport express, but it seemd that I always need a ethernetcable...apple support insured me it is possible but the airport utility software only allows me to extend using a cable it seems....

Couple of thoughts here.......
The AirPort Express will only extend a wireless network if you have another Apple router providing the wireless network to be extended.
Is your "main" wireless router an Apple product? If yes, what model number do you have?
It would also help if we could get the model number of the AirPort Express. Some older versions are not capable of extending a wireless network.

Extend wireless network with AirPort Express

How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

HT5022 I'm trying to add a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version. I've downloaded all available updates of the OS and the utility.. Help!

I'm trying to add my HP wireless printer as a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version. I've downloaded all available updates of the OS and the utility.. Help!

Why would you need to ADD a new Client. Unless the APE sytem is completely different then any other Wireless router the printer should get an IP address from the router. That is IF the printer is setup to get an IP from the LAN DHCP server.
Now you may want to make that IP it does get a Staticly assign IP address so it never changes, which will screw up printing if it does change. But i don't know if you can do that with APE routers.

How can I rename an established wireless network using airport extreme?

How can I rename an established wireless network using airport extreme?

Thanks for the info. On your Mac......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the picture of the AirPort Extreme
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window that appears
Edit/backspace out the Wireless Network Name and type in a new name that you want to use
Click Update at the lower right of the window
Wait a full minute for the AirPort Extreme to restart
Close AirPort Utility
The new network that you named will use the same network password that you set up originally.

Extending Sky Wireless Network with Airport Express.

I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
Does anybody know if this is possible and if so, can they please advise me how I do this. (I am using Windows 7 on my Dell laptop)

I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
Unfortunately, the salesman may not have understood your question, or he may have given you incorrect information.
It's possible to have the AirPort Express provide more wireless coverage if you connect it using an ethernet cable permanently to your Sky router.
But, the AirPort Express cannot "extend" the wireless network produced by the Sky by connecting using wireless only. The "extend" feature will only work if you have an Apple to Apple wireless connection. This feature is not compatible with the products of other manufacturers.

Extending an existing wireless network with an airport express

My wireless signal is quite weak in my room so I'm looking for a way to extend the range of the network by using an airport express. I understand i can't do this wirelessly but is it possible to run an ethernet cable from my existing router to the airport express in my room and then have a stronger signal in my room?
Thanks in advance!

Welcome to the discussion area, Aaron!
If you connect an ethernet cable from your existing router to the AirPort Express, and then configure the Express to "Create a wireless network" with the same name, security settings and password, this will in effect, extend your current wireless network.
The Express must be configured as a "bridge" to operate correctly on your network when you do this, meaning that the setting for Connection Sharing on the Express will be set to "Off (Bridge Mode).

Extending Gen 1 Time Capsule Wireless network with Airport Express N

I am having difficulty setting up my new Airport Express w/ 802.11N (SKU# MB321LL/A) to extend the wireless network from my Time Capsule (SKU# MB276LL/A).
My setup is as follows:
Time Capsule is connected to Cable modem with the following wireless settings:
Wireless mode -> Create a Wireless Network
Allow this network to be extended -> Checked
Radio Mode ->802.11n (5Ghz N only)
Wireless Security -> WPA2 Personal
The issue is the when I attempt to setup the AE to extend the network. I match the settings to the Time Capsule:
Wireless Mode -> Extend a Network
Select the Time Capsule Network
Allow wireless clients -> Checked
Wireless Security -> WPA2 Personal
However after I reset the AE the LED glows Amber and the following problem is reported:
+Wireless Network+
+This AirPort wireless device is set up to join a specific wireless network that can't be found. If you don't see the network that you want to join in the Network Name Pop-up menu, enter the network name and network password if necessary to try again.+
When I check the Airport->Wireless tab the settings were as before.
Any thoughts on this? Thanks.

Welcome to the discussions!
Have you tried to position the AirPort Express close, say 10-15 feet, as a test to see if it will connect that way?
If so, then move it back another 10-15 feet, etc.
5 GHz signals do not travel well or penetrate surfaces very well, so my first thought was that the signal was not strong enough for the Express to pick it up where you had it located.
Message was edited by: Bob Timmons

Can't extend my Apple Wireless network with Airport Utility 6

Similar Messages

Maybe you are looking for