Can't find autonomous image to Cisco Aironet 1140

Can anyone gives a link?
-JeIlMa

Here you go:
http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N

Similar Messages

  • How to load a boot image to cisco aironet 1140 series after missing boot image

    Hi all,
    I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
    When i tried next time, by pressing escape it shows this message that i have mentioned below.
    ap:
    ap:
    using  eeprom values
    WRDTR,CLKTR: 0x83000800 0x40000000
    RQDC ,RFDC : 0x80000035 0x00000208
    using ÿÿÿÿ ddr static values from serial eeprom
    ddr init done
    Running Normal Memtest...
    Passed.
    IOS Bootloader - Starting system.
    FLASH CHIP:  Numonyx P33
    Checking for Over Erased blocks
    Xmodem file system is available.
    DDR values used from system serial eeprom.
    WRDTR,CLKTR: 0x83000800, 0x40000000
    RQDC, RFDC : 0x80000035, 0x00000208
    PCIE0: link is up.
    PCIE0: VC0 is active
    PCIE1: link is NOT up.
    PCIE1 port 1 not initialized
    PCIEx: initialization done
    flashfs[0]: 1 files, 1 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 32385024
    flashfs[0]: Bytes used: 1536
    flashfs[0]: Bytes available: 32383488
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from system serial eeprom...Done
    Base Ethernet MAC address: 28:94:0f:d6:c8:62
    Ethernet speed is 100 Mb - FULL duplex
    The system is unable to boot automatically because there
    are no bootable files.
    C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Tue 18-Oct-11 14:51 by prod_rel_team
    ap:
    So , now my question is how to load the boot image ? From where will we get this ? OR
    I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?

    Take a look at this link as it should have the info you need
    https://supportforums.cisco.com/docs/DOC-14636
    Sent from Cisco Technical Support iPhone App

  • Lightroom 3 Can't Find My Images

    I use several external hard drives for my images and they occasionally get moved either to another folder or to another hard drive.  When this happens, Lightroom can't find the image so I go to the image in its new location and Lightroom finds it and all its neighbors.  That worked great in Lightroom 2 but does not work at all in Lightroom 3.  I can't change the original file folder structure at all.  Lightroom can't find the image even though I'm clicking on it.  Then I try to click a bit harder and eventually start pounding on the keyboard and shouting at Lightroom, "It's right here!"  Any suggestions or bug knowledge regarding this?
    Thanks,
    Richard

    brianbotticelli wrote:
    If you right click on the folder in the navigator and choose Update Folder Location, this will not work in LR3 running Mac OS 10.6.4.
    This should definitely work! What is happening if you do that, and what are your detailed steps?
    ... Also, if you right click on an image thumbnail and choose Show in Finder, then reset your image path from the dialogue box, this will not work either.
    As noted here, this seems to be a bug.
    Beat Gossweiler
    Switzerland
    Edit:
    If you move an entire folder from outside LR, you should get a "?" right next to the folder, and the option "Update Folder Location" is not availble, but "Find missing Folder". If you only move some images from one folder to another, "Update Folder Location" is not the correct way to go.
    Message was edited by: b_gossweiler

  • HT201386 how can I find the Image number of a particular photo in the Photos app included with iPad Air?

    how can I find the Image number of a particular photo in the Photos app included with iPad Air?

    Hello yamacutta,
    Thanks for using Apple Support Communities.
    The Photos app will not show you the actual file name of the photo.  However when you go through the image import process on your computer, you should be able to see both the thumbnail of the photo, as well as the filename of the image.
    Import photos and videos from your iPhone, iPad, or iPod touch to your Mac or Windows PC - Apple Support
    Take care,
    Alex H.

  • My iWeb image names are incompatible with FTP servers and must be renamed but I can't find the images in iWeb. I can upload to a desktop file and change them there but then I would need to download them to a new site in iWeb to publish them.

    my iWeb image names are incompatible with FTP servers and must be renamed but I can't find the images in iWeb. I can upload to a desktop file and change them there but then I would need to download them to a new site in iWeb to publish them. 
    What's the answer?
    Thanks 

    Many thanks to  responded to my question and sorry not to get back sooner.
    Yes, I discovered by this unfortunate experience that the names of photos are a serious issue if the site is to ever go to an FTP server.  Apple should discuss this carefully in their "manual".
    One more question:  I uploaded the website to a folder on my desktop. When I open it, unlike the photos in iWeb, there are folders for each page which have all the photos in them. I went through each folder and changed the names to be FTP compatible. I'm using iWeb SEO Tool which allows one to upload from this local folder to an FTP server but having trouble.
    Is this because there is an imbedment in iWeb that uses the old photo names to link to the actual photos and it can't find them because of the name changes?
    Thanks again for your help ...
    Phil McP

  • I can't find apply image command

    I'm learning with the Elements 8 trial system.  Trying to blend two photos. The help page gives instructions to us the Apply Image but it doesn't show up when I click image. Where is it?

    Wow!  That took care of my question and then some.  Thank you very much.
    Thank you very much!
    Tim McNulty
    Date: Thu, 16 Sep 2010 05:04:33 -0600
    From: [email protected]
    To: [email protected]
    Subject: I can't find apply image command
    Hi,
    Please Refer the following link it may help you.
    http://www.photoshopessentials.com/photo-effects/elements/photo-blend/
    Thanks
    www.mediacafe.in
    >

  • Can't Find Core Image on Computer

    I have installed Developer on my harddrive, gone to applications and find Core Audio and Core Foundation but I can't find Core Image at all. I'm wanting to experiment with it's editing features on digital images.
    I have Tiger 10.4.6 and I assume I had the correct version of Developer Tools.
    Need some advice.
    Bill

    Core Image is part of Quartz. It's a collection of programming APIs, not a separate application.
    However, my Dev Tools installation includes a pre-built sample app called "Core Image Fun House" found in "Developer -> Applications -> Graphics Tools". There area also several Core Image example programs found in "Developer -> Examples -> Quartz -> Core Image".
    If you're interested in examining the Core Image header files they can be found in "System -> Library -> Frameworks -> QuartzCore.framework -> Headers".
    You might also want to experiment with "Quartz Composer" (also found in "Developer -> Applications -> Graphics Tools".
    Reference documentation for all this stuff should have been installed with your copy of Xcode Tools (current version is 2.3).
    Steve

  • Recently Image Capture does not work.  It can't find one camera and can't find the images from another camera.  Help?

    Recently Image Capture stopped working.  It can't find one camera and can't find the images from a different camera.  Help?

    Launch iPhoto. From the menu: iPhoto>Preferences>General: Select Connecting camera opens>Image Capture.

  • Configuring Cisco Aironet 1140 for Radius and setting up a Radius server

    guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
    When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?

    Here are other links with examples:
    https://supportforums.cisco.com/thread/331581
    http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
    http://downloads.avaya.com/css/P8/documents/100041614
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Cisco Aironet 1140: 3 of our 4 are always hanging

    Our office has 4 Cisco Aironet 1140 access points mounted on the ceiling. They are all powered via PoE. Every few days 3 of the 4 access points hang and have to be rebooted. When they hang I am not able to connect to their web interface to check the logs. The fourth, for some reason, always seems to stay alive.
    I checked the configuration for all AP's and "Hot Standby" is disabled
    They are all using static IP addresses. I've tried 2 different banks of static IP addresses and 3 of 4 still hange so I don't think this is an IP conflict
    I have saved the configurations and compared them and they are all identical, where possible.
    They all have software version: 12.4(21a)JA1
    They all have bootloader version: 12.4(23c)JA1
    I have tried to download the latest software/firmware, but unfortunately I do not have a valid service contract in place with Cisco and therefore can't download the latest version. All of our CISCO hardware was purchased from Amazon resellers and they can't seem to help me with this. I have also tried to contact Cisco and they can't seem to help either. If anyone has a suggestion on how I can get a valid service contract that information would also be very helpful!!!
    Does anyone have any ideas why 3 of our 4 access points would hang? When they hang, I can't login to the web interface and the logs seem to reset when I reset each access point. I have also set up an rsyslog server and I don't see a log entry that would indicate a problem.
    Any ideas?
    Thank you

    Here is the config for one of the AP's that keeps hanging:
    ! Last configuration change at 09:18:05 -1000 Mon Jan 30 2012 by admin
    ! NVRAM config last updated at 09:18:05 -1000 Mon Jan 30 2012 by admin
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname XXX2
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    clock timezone -1000 -10
    ip name-server 8.8.8.8
    ip name-server 8.8.4.4
    dot11 syslog
    dot11 ssid XXX2
       authentication open
       authentication key-management wpa version 2
       guest-mode
       wpa-psk ascii 7 01234567890123456789012
    username admin privilege 15 password 7 01234567890123456789012
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm
    ssid XXX2
    antenna gain 0
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no keepalive
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.100.252 255.255.255.0
    no ip route-cache
    ip default-gateway 192.168.100.1
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    snmp-server community MyCommunity RO
    bridge 1 route ip
    line con 0
    line vty 0 4
    sntp server 192.43.244.18
    sntp broadcast client
    end

  • Can't find disk image to delete

    I made a disk image from a home movie dvd I made so I could duplicate it. Afterward I wanted to delete it but can't find it using Spotlight or All My Files or anything else. When I right-click and choose open in finder, it says it's on the desktop but it's on there only in the finder not on the actual desktop when I use a hot corner to reveal the desktop. I read a post that said there were programs you can download to aid in removing them, is that to say Apple didn't build something into its operating system (Mountain Lion 10.8.5) to do it? That post was the only one even dealing with this issue and was from 2008 and locked. Any help would be very appreciated. Thanks.

    Jules1857 wrote:
    I made a disk image from a home movie dvd I made so I could duplicate it. Afterward I wanted to delete it but can't find it using Spotlight or All My Files or anything else...
    Presumably, you know at least a portion of the exact name of the disk image. If so, check out EasyFind in the App store. If it's anywhere on your HD, EasyFind will find it and "Reveal in Finder" will take you there.

  • I can't find the image object menu item when trying to add an image placeholder in dreamweaver cs6

    I am new to dreamweaver, and am walking through some tutorials.  I can't seem to find the image object menu item to place a image placeholder on my page.  Any suggestions?  Do I have a setting that is currently hiding its visibility?  Thanks  (I am currently working with dreamweaver cs6)

    They removed it in the new Cloud version of DW CS6.
    http://blogs.adobe.com/dreamweaver/2012/10/dreamweaver-creative-cloud-update-12-1-faqs.htm l

  • Can't find still images???

    I dragged and dropped some still images into iMovie '09 for a project to use with some video clips.   When I right-click on these images in the Project window to "reveal in finder", nothing happens?  This works for all the video clips in my project, but nothing happens on any of the still images?  Please help because I have tons of stills on tons of drives and I can't go through everything again to find these images again.
    Thanks for ALL your help in advance  ----------<-<@

    Open the video animation (Control-v). In transform>All click and drag the X and Y keyframes (which should be together) – left to speed up the scale change and right to slow it down . It may take a little practice to get this to work (I seldom get it right the first try).
    You could do this individually for each clip, or you wanted to adjust multiple clips you can copy and paste attributes to your other other clips.
    Russ

  • How can I find the image file for iTunes album artwork?

    I know how to see the image, how to search for album artwork on the web, and how to save a new or different image. However, I want to be able to find specific images in Finder that are already connected with an album. I am not able to zero in on it. All I find is a collection of folders.

    These things accesible by control clicking (or right clicking with a multibutton mouse) are what are known as contextual menus and are incredibly powerful timesavers.  Try control clicking on things and see what you find. 

  • Cisco Aironet 1140 Issues (Dropping clients, 5GHz issue, AP Switching)

    Greetings,
    We've been having issues for a while with these Aironet 1140's. We have two of them in the office and the issue is similar to the first issue displayed in this post:
    https://supportforums.cisco.com/docs/DOC-26228
    The only difference is that I can't do this since we don't use a controller.
    We're using Mac clients on Lion/Mt. Lion. We have no issues connecting to the access points, but occassionally the user will drop off one of the AP's(Access Point 2). Recently I changed the setup from TKIP/WPA to AES-CCM/WPA to get the PHY address to 802.11N instead of 802.11G. I got the speeds working fine, but I suppose this caused an issue of people dropping off at different times. I noticed if I remove the SSID from the preferred list and reconnect it goes from WPA to WPA2. Not sure if this is relevant information, just trying to list what I can to resolve this issue. I haven't had any reported issues with the other Access Point(Access Point 1).
    Another issue we have is getting the radio to work on 5GHz for Access Point 1. It seems when a user is connected to the 5GHz signal, it will not load any web pages. Can ping out just fine, and ping internally as well. I've checked to see if the client is getting an IP address, and it is. It also has DNS set to 8.8.8.8 and another DNS IP we use. The other Access Point seems to work just fine with 5GHz enabled. Both work with 2.4GHz with no issues at all.
    Lastly, clients are not switching Access Points to the strongest signal. I've tried this test with 5+ machines running different OS's from Snow Leopard to Mt. Lion. The client will not switch over passively, the Laptop must be closed and reopened to re-establish the connection to grab the closest signal. This isn't a huge issue, but it's something I'd like to get fixed. This could have been an ongoing issue before I switched the AP's to AES-CCM, but I've only noticed it after the fact.
    If there's any additional information needed that could help resolve these issues, let me know.
    Thanks!

    The wireless clients/devices decides which WAPs to join.  It's not a "Cisco thing".  It's the standard.
    That's what I figured, it's just an issue we have been having lately and trying to rule out the possibility it might be an Access Point issue.
    Did you enable WPA and WPA2???  Apple does not like to "choose".  You have to either use WPA OR WPA2.
    Actually, yes I should have included my steps of trying to resolve the issue. For some reason, the SSID would not appear in the listing of SSID's so I removed the preferred connection, which was WPA, and manually added it to be WPA2 Personal on the client. Still saw some issues with a few users, others seem to have rectified or they're not telling me.
    I checked the event logs on the device and saw this:
    Packet to client e0f8.4735.c16e reached max retries, removing the client
    After some research, it was recommended to raise the packet retry value to 128. I haven't received any complaints from the 3 people that usually complain about dropped wifi yet, but it's still too soon to say.
    The only thing I can think of is the signal strength.  Disable the 2.4 Ghz and see what signal strength you are getting with the 5.0 Ghz.
    It should not be signal strength since I am about 10 feet away on my test machine which has the issue as well as any other clients in any distance long enough to grab the connection. I will try turning off 2.4 when there's nobody in the office tomorrow in the morning to see if that actually works. I would like to have it dual band though since we're not all at 5GHz here. With this issue, I was actually fearing that there just may be an issue with the 5GHz radio hardware. We also have an extra 1140 laying around I used for testing; the 5GHz radio worked with identical settings to the one not working.
    Thanks for the reply! I will take a look at what you suggested a little further and keep this updated if increasing the packet retry value actually rectified the problem just in case someone else has the same issue.

Maybe you are looking for