Can't get Access Restrictions to work WRT54G v3
I am trying to get a cell phone to have access to my LAN from 3am to 7am. I gave the policy a name, allowed access, checked everyday and the time 3a to 7a. Under edit list of PCs, I entered the MAC address of the phone, and I have also entered the MAC address of the phone on the wireless>edit mac filter list, though didn't know if I should.
Anyway, I can't seem to get the Access Restriction to work and would appeciate any guidance...thanks
hmmmmmm... have you tried using the IP address instead? based on my experience, the Acces Restriction policies are a bit tricky.
Too bad the WRT54g has no parental controls which is a lot easier to configure.
"Don't fix it if it ain't broken."
Similar Messages
-
WRT54GL Cannot get access restrictions to work
I purchased a WRT54GL router (v1.1 with firmware 4.30.7) and I cannot for the life of me get the access restrictions to work. I made three policies, one for my PC with 24/7 access and one for the kids PC with access from 7pm to 9pm during the weekdays and another for the kids PC with access from 12pm to 10pm on the weekends. whenever I enable the policies, my PC can access the internet but the kids cannot (of course during the proper times). When I disable their policies they still cannot get on till I also disable my policy. I have gone thru everything I can think of including multiple hard resets but access restriction simply will not work.
Of course there is no mention of my hardware or firmware version anywhere on the linksys support system! Anyone have any thoughts?hmmmmmm... have you tried using the IP address instead? based on my experience, the Acces Restriction policies are a bit tricky.
Too bad the WRT54g has no parental controls which is a lot easier to configure.
"Don't fix it if it ain't broken." -
How do I get Access Restrictions to work
I have a WRT54GS with firmware ver 7.50.0. I would like to set up time restrictions (14 year old - self explanatory) and don't know how to go about it. I have gone in and set up times, but it has no effect.
I may be going out on a limb here and hope the explanation isn't too technical. I have read quite a few posts...and feel quite lucky that I got this thing set up in the first place as everyone seems to be much more technical than I am. Any help in as simple terms as possible would be appreciated!!
Also, supposing I get this to work, is there a way to limit what networks her laptop can access? Apparently a neighbor has a wireless network that she can access so if I time limit mine she could just connect to that one. Thx!I actually DID get it to work yesterday, but not really in the way I had wanted. I found the MAC address in Linksys EasyLink Advisor. (thx for the other directions gv) All I had to do was check the 'advanced view' box and it gives you that and the IP address. Anyway, I set it up to start at 5:30 pm, about 3 minutes from the time it was right then. My daughter was on and didn't complain about getting kicked off, so I thought it didn't work. Then we had to leave for a while and when we came back, she went to get on and came to tell me it was telling her "local" only, or some similar message. She couldn't get on MY network. Unfortunately, she got on the neighbors.
So I guess it works to the extent of preventing logging on, while I was hoping it would kick her off at 9 or 10 pm. But I also found, when I went in to change the time to something else so she could access my network then, it made the desktop and her laptop run *really* slow. I ended up powering down the router and bringing it back up and then it was ok.
It seems this is not really going to do the job I had hoped and with the neighbor's network available, she can get on anytime. Is there a way to make the laptop not be able to connect to a particular network?
We have had talks about the dangers, etc. and I trust her, it's the problem of not being able to pull herself away from it. I can go on and on about it, just like I do about cleaning her bathroom or bedroom, but every day it's like I never said it. She's a teenager. Sooooo, when it comes down to it, I will phyically have to take away the laptop when I decide enough is enough. I'd rather blame the technology, but if I have to be the bad guy, I will. -
Can't get direct rendering to work
On my notebook with an Intel 945GM card, I can't get direct rendering to work.
I'm using the 'xf86-video-intel' driver.
/etc/X11/xorg.conf:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Touchpad" "AlwaysCore SendCoreEvents"
# InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "DontZap"
Option "DontZoom"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "xtrap"
Load "extmod"
Load "GLcore"
Load "record"
Load "dbe"
Load "glx"
Load "dri"
Load "freetype"
Load "synaptics"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "InputDevice"
Driver "synaptics"
Identifier "Touchpad"
Option "Device" "/dev/psaux"
Option "Protocol" "auto-dev"
Option "LeftEdge" "1700"
Option "RightEdge" "5300"
Option "TopEdge" "1700"
Option "BottomEdge" "4200"
Option "FingerLow" "25"
Option "FingerHigh" "30"
Option "MaxTapTime" "180"
Option "MaxTapMove" "220"
Option "VertScrollDelta" "100"
Option "MinSpeed" "0.06"
Option "MaxSpeed" "0.12"
Option "AccelFactor" "0.0010"
Option "SHMConfig" "on"
# Option "Repeater" "/dev/ps2mouse"
EndSection
Section "Monitor"
#DisplaySize 330 210 # mm
DisplaySize 338 211
Identifier "Monitor0"
VendorName "AUO"
ModelName "2174"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "ColorKey" # <i>
#Option "CacheLines" # <i>
#Option "Dac6Bit" # [<bool>]
#Option "DRI" # [<bool>]
#Option "NoDDC" # [<bool>]
#Option "ShowCache" # [<bool>]
#Option "XvMCSurfaces" # <i>
#Option "PageFlip" # [<bool>]
Identifier "Card0"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
BusID "PCI:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1280x800" "1152x864" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1280x800" "1152x864" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x800" "1152x864" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
And here is /var/log/Xorg.0.log:
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.4.0.90
Release Date: 5 September 2007
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-ARCH i686
Current Operating System: Linux zg6y3zg9f3x 2.6.24.3-ARCH #2 SMP PREEMPT Sun Mar 2 23:22:11 CET 2008 i686
Build Date: 03 February 2008 02:54:48PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Mar 3 00:20:16 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Touchpad"
(**) |-->Input Device "Keyboard0"
(**) Option "DontZap"
(**) Option "DontZoom"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(==) Including the default font path /usr/share/fonts/misc,/usr/share/fonts/100dpi:unscaled,/usr/share/fonts/75dpi:unscaled,/usr/share/fonts/TTF,/usr/share/fonts/Type1.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(==) |-->Input Device "Mouse0"
(==) The core pointer device wasn't specified explicitly in the layout.
Using the first mouse device.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81d65c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 2.0
X.Org XInput driver : 2.0
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(--) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,27a0 card 1025,0090 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:02:0: chip 8086,27a2 card 1025,0090 rev 03 class 03,00,00 hdr 80
(II) PCI: 00:02:1: chip 8086,27a6 card 1025,0090 rev 03 class 03,80,00 hdr 80
(II) PCI: 00:1b:0: chip 8086,27d8 card 1025,0090 rev 02 class 04,03,00 hdr 00
(II) PCI: 00:1c:0: chip 8086,27d0 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:1: chip 8086,27d2 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:2: chip 8086,27d4 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:3: chip 8086,27d6 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1d:0: chip 8086,27c8 card 1025,0090 rev 02 class 0c,03,00 hdr 80
(II) PCI: 00:1d:1: chip 8086,27c9 card 1025,0090 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:2: chip 8086,27ca card 1025,0090 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:3: chip 8086,27cb card 1025,0090 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:7: chip 8086,27cc card 1025,0090 rev 02 class 0c,03,20 hdr 00
(II) PCI: 00:1e:0: chip 8086,2448 card 0000,0000 rev e2 class 06,04,01 hdr 01
(II) PCI: 00:1f:0: chip 8086,27b9 card 1025,0090 rev 02 class 06,01,00 hdr 80
(II) PCI: 00:1f:2: chip 8086,27c4 card 1025,0090 rev 02 class 01,01,80 hdr 00
(II) PCI: 00:1f:3: chip 8086,27da card 1025,0090 rev 02 class 0c,05,00 hdr 00
(II) PCI: 05:00:0: chip 8086,4222 card 8086,1000 rev 02 class 02,80,00 hdr 00
(II) PCI: 06:01:0: chip 14e4,170c card 1025,0090 rev 02 class 02,00,00 hdr 00
(II) PCI: 06:04:0: chip 1524,1412 card 1400,0000 rev 10 class 06,07,00 hdr 82
(II) PCI: 06:04:1: chip 1524,0530 card 1025,0090 rev 01 class 05,01,00 hdr 80
(II) PCI: 06:04:2: chip 1524,0550 card 1025,0090 rev 01 class 08,05,01 hdr 80
(II) PCI: 06:04:3: chip 1524,0520 card 1025,0090 rev 01 class 05,01,00 hdr 80
(II) PCI: 06:04:4: chip 1524,0551 card 1025,0090 rev 01 class 05,01,00 hdr 80
(II) PCI: End of PCI scan
(II) Intel Bridge workaround enabled
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,7), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:28:0), (0,2,2), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 3: bridge is at (0:28:1), (0,3,3), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 4: bridge is at (0:28:2), (0,4,4), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 5: bridge is at (0:28:3), (0,5,5), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 5 non-prefetchable memory range:
[0] -1 0 0xd0100000 - 0xd01fffff (0x100000) MX[b]
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 6: bridge is at (0:30:0), (0,6,7), BCTRL: 0x0000 (VGA_EN is cleared)
(II) Bus 6 non-prefetchable memory range:
[0] -1 0 0xd0000000 - 0xd00fffff (0x100000) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:31:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-CardBus bridge:
(II) Bus 7: bridge is at (6:4:0), (6,7,10), BCTRL: 0x0740 (VGA_EN is cleared)
(--) PCI:*(0:2:0) Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xd0200000/19, 0xc0000000/28, 0xd0300000/18, I/O @ 0x5088/3
(--) PCI: (0:2:1) Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xd0280000/19
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) Active PCI resource ranges:
[0] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[1] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[2] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[3] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[4] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[5] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[6] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[7] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[8] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[9] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[10] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[11] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[12] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[13] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[14] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[15] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[16] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[17] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[18] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) Inactive PCI resource ranges:
[0] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[1] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[2] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[3] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[1] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[2] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[3] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[4] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[5] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[6] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[7] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[8] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[9] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[10] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[11] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[12] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[13] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[14] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[15] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[16] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[17] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[18] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) Inactive PCI resource ranges after removing overlaps:
[0] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[1] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[2] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[3] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[5] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[6] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[7] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[8] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[9] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[10] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[11] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[12] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[13] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[14] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[15] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[18] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[19] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[20] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[22] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[23] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[24] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[25] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[26] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[27] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[28] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "xtrap"
(II) Loading /usr/lib/xorg/modules/extensions//libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DEC-XTRAP
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.4.0.90, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 4.3.99.902, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 2.2.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "synaptics"
(II) Reloading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
965GM, 965GME/GLE, G33, Q35, Q33, Intel Integrated Graphics Device
(II) Primary Device is: PCI 00:02:0
(WW) intel: No matching Device section for instance (BusID PCI:0:2:1) found
(--) Chipset 945GM found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[5] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[6] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[7] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[8] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[9] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[10] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[11] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[12] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[13] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[14] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[15] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[18] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[19] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[20] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[22] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[23] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[24] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[25] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[26] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[27] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[28] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[5] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[6] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[7] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[8] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[9] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[10] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[11] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[12] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[13] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[14] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[15] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[16] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[19] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[20] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[21] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[22] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[23] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[24] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[25] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[26] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[27] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[28] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[29] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[30] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[31] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
[32] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[33] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.1.0
ABI class: X.Org Video Driver, version 2.0
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 0.1.0
ABI class: X.Org Video Driver, version 2.0
(**) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 945GM
(--) intel(0): Chipset: "945GM"
(--) intel(0): Linear framebuffer at 0xC0000000
(--) intel(0): IO registers at addr 0xD0200000
(II) intel(0): 2 display pipes available.
(==) intel(0): Using EXA for acceleration
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"(II) Module "i2c" already built-in
(II) intel(0): Output VGA using monitor section Monitor0
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): EDID vendor "AUO", prod id 8564
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) intel(0): initializing int10
(WW) intel(0): Bad V_BIOS checksum
(II) intel(0): Primary V_BIOS segment is: 0xc000
(II) intel(0): VESA BIOS detected
(II) intel(0): VESA VBE Version 3.0
(II) intel(0): VESA VBE Total Mem: 7872 kB
(II) intel(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip Accelerated VGA BIOS
(II) intel(0): VESA VBE OEM Software Rev: 1.0
(II) intel(0): VESA VBE OEM Vendor: Intel Corporation
(II) intel(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics Controller
(II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(0): Output TV has no monitor section
(II) intel(0): EDID vendor "AUO", prod id 8564
(II) intel(0): Output VGA disconnected
(II) intel(0): Output LVDS connected
(II) intel(0): Output TV disconnected
(II) intel(0): Output LVDS using initial mode 1280x800
(II) intel(0): Monitoring connected displays enabled
(II) intel(0): detected 256 kB GTT.
(II) intel(0): detected 7932 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Will not try to enable page flipping
(==) intel(0): Triple buffering disabled
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(**) intel(0): Display dimensions: (338, 211) mm
(**) intel(0): DPI set to (96, 154)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 2.2.0
ABI class: X.Org Video Driver, version 2.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module "ramdac" already built-in
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to 0xd000000a
(WW) intel(0): PP_STATUS before: on, ready, sequencing idle
(WW) intel(0): PP_STATUS after: on, ready, sequencing on
(WW) intel(0): Register 0x68080 (TV_FILTER_CTL_1) changed from 0x8000085e to 0x800010bb
(WW) intel(0): Register 0x68084 (TV_FILTER_CTL_2) changed from 0x00012d2d to 0x00028283
(WW) intel(0): Register 0x68088 (TV_FILTER_CTL_3) changed from 0x00009696 to 0x00014141
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xd0300000 - 0xd033ffff (0x40000) MS[b]
[1] 0 0 0xc0000000 - 0xcfffffff (0x10000000) MS[b]
[2] 0 0 0xd0200000 - 0xd027ffff (0x80000) MS[b]
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[7] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[8] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[9] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[10] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[11] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[12] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[14] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[15] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[16] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[17] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[18] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[19] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprD)
[20] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprD)
[21] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprD)
[22] 0 0 0x00005088 - 0x0000508f (0x8) IS[b]
[23] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[24] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[25] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[26] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[27] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[28] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[29] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[30] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[31] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[32] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[33] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[34] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[35] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
[36] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[37] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) intel(0): Kernel reported 488960 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 1955836 kB available
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
[drm] failed to load kernel module "i915"
(EE) [drm] drmOpen failed.
(EE) intel(0): [dri] DRIScreenInit failed. Disabling DRI.
(==) intel(0): VideoRam: 262144 KB
(**) intel(0): Framebuffer compression enabled
(**) intel(0): Tiling enabled
(II) intel(0): adjusting plane->pipe mappings to allow for framebuffer compression
(II) intel(0): Page Flipping disabled
(==) intel(0): Write-combining range (0xc0000000,0x10000000)
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) EXA(0): Offscreen pixmap area of 19660800 bytes
(II) EXA(0): Driver registered support for the following operations:
(II) Solid
(II) Copy
(II) Composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x007bf000 (pgoffset 1983)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x00c80000 (pgoffset 3200)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB)
(II) intel(0): 0x00020000-0x0061ffff: compressed frame buffer (6144 kB, 0x000000007f820000 physical
(II) intel(0): 0x00620000-0x00620fff: compressed ll buffer (4 kB, 0x000000007fe20000 physical
(II) intel(0): 0x00621000-0x0062afff: HW cursors (40 kB, 0x000000007fe21000 physical
(II) intel(0): 0x0062b000-0x00632fff: logical 3D context (32 kB)
(II) intel(0): 0x00633000-0x00633fff: overlay registers (4 kB, 0x000000007fe33000 physical
(II) intel(0): 0x00640000-0x00c7ffff: front buffer (6400 kB)
(II) intel(0): 0x007bf000: end of stolen memory
(II) intel(0): 0x00c80000-0x01f3ffff: exa offscreen (19200 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is off
(II) intel(0): Display plane B is now disabled and connected to pipe A.
(II) intel(0): Pipe B is on
(II) intel(0): Display plane A is now enabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output LVDS is connected to pipe B
(II) intel(0): Output TV is connected to pipe none
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): Set up textured video
(II) intel(0): Set up overlay video
(II) intel(0): direct rendering: Failed
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) AIGLX: Screen 0 is not DRI capable
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/xorg/modules/extensions//libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) GLX: Initialized MESA-PROXY GL provider for screen 0
(II) intel(0): Setting screen physical size to 331 x 207
(II) Synaptics touchpad driver version 0.14.6 (1406)
(--) Touchpad auto-dev sets device to /dev/input/event5
(**) Option "Device" "/dev/input/event5"
(**) Option "SHMConfig" "on"
(**) Option "LeftEdge" "1700"
(**) Option "RightEdge" "5300"
(**) Option "TopEdge" "1700"
(**) Option "BottomEdge" "4200"
(**) Option "VertScrollDelta" "100"
(**) Option "FingerLow" "25"
(**) Option "FingerHigh" "30"
(**) Option "MaxTapTime" "180"
(**) Option "MaxTapMove" "220"
(--) Touchpad touchpad found
(**) Touchpad: always reports core events
(**) Option "CoreKeyboard"
(**) Keyboard0: always reports core events
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "auto"
(**) Mouse0: Device: "/dev/input/mice"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: always reports core events
(**) Option "Device" "/dev/input/mice"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5 6 7"
(**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
(**) Mouse0: Buttons: 11
(**) Mouse0: Sensitivity: 1
(II) evaluating device (Mouse0)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) evaluating device (Keyboard0)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) evaluating device (Touchpad)
(II) XINPUT: Adding extended input device "Touchpad" (type: MOUSE)
(--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(--) Touchpad auto-dev sets device to /dev/input/event5
(**) Option "Device" "/dev/input/event5"
(--) Touchpad touchpad found
Could not init font path element /usr/share/fonts/Type1, removing from list!
AUDIT: Mon Mar 3 00:21:47 2008: 10765 X: client 7 rejected from local host (uid 1001)
(II) intel(0): xf86UnbindGARTMemory: unbind key 0
(II) intel(0): xf86UnbindGARTMemory: unbind key 1
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x007bf000 (pgoffset 1983)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x00c80000 (pgoffset 3200)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB)
(II) intel(0): 0x00020000-0x0061ffff: compressed frame buffer (6144 kB, 0x000000007f820000 physical
(II) intel(0): 0x00620000-0x00620fff: compressed ll buffer (4 kB, 0x000000007fe20000 physical
(II) intel(0): 0x00621000-0x0062afff: HW cursors (40 kB, 0x000000007fe21000 physical
(II) intel(0): 0x0062b000-0x00632fff: logical 3D context (32 kB)
(II) intel(0): 0x00633000-0x00633fff: overlay registers (4 kB, 0x000000007fe33000 physical
(II) intel(0): 0x00640000-0x00c7ffff: front buffer (6400 kB)
(II) intel(0): 0x007bf000: end of stolen memory
(II) intel(0): 0x00c80000-0x01f3ffff: exa offscreen (19200 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is off
(II) intel(0): Display plane B is now disabled and connected to pipe B.
(II) intel(0): Pipe B is on
(II) intel(0): Display plane A is now enabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output LVDS is connected to pipe B
(II) intel(0): Output TV is connected to pipe none
(II) Mouse0: ps2EnableDataReporting: succeeded
(--) Touchpad auto-dev sets device to /dev/input/event5
(**) Option "Device" "/dev/input/event5"
(--) Touchpad touchpad found
Can anyone help me with this?
Last edited by bughunter2 (2008-03-03 01:06:30)The standard arch kernel includes all the required modules, at most you need to load them explicitly listing them in MODULES in /etc/rc.conf
You need also the hw specific stuff, that is i915 and intelagp. Check lsmod and see if they are loaded. If they are not, inspect dmesg and see if udev tries to load them and fails for some reason.
I remember some cases where intelagp and i915 are not loaded by udev in the right order, if this is your case you can try to list them in the right order in MODULES.
There should be no need to recompile the kernel or to install a particular version of dri (just use the arch packages for mesa, libdrm etc; but I guess you have them already) -
Can't get video chat to work outside of LAN...
Hello,
I can't get video chat to work.
All computers, LAN and WAN are running the latest iChat under 10.4 (including latest updates).
Within our LAN, via Bonjour, everything is fine.
I'm now trying to set up an offsite Intel iMac (10.4) and I can't connect via video chat with them.
I've had this problem in the past and eventually gave up (so much for "it just works" - I've spent the last 10+ years dealing with Macs and Mac-based networking, I can't imagine "my dad" figuring this all out). Trying again with fingers crossed...?
If someone could help, it'd be much appreciated.
Thanks,
Kristin.
The studio router/firewall is a SonicWall TZ 170 Standard.
This router has a static IP.
All suggested ports on the SonicWall are set up correctly to allow in/out from our LAN.
All computers on the LAN have static IP addresses.
Quicktime streaming settings set as suggested.
OS X Firewall on all computers = OFF.
No iChat add-ons on any computers.
Internet connection speed = 7404 kb/s
The offside router/firewall is a LinkSys WRT54G
This router does not have a static IP.
DMZ is ON and set to the only computer connected to it.
Computer has a static IP address.
Quicktime streaming settings set as suggested.
OS X Firewall on all computers = OFF.
No iChat add-ons on computer.
Internet connection speed = 5116 kb/s
If any more information is required to help you help me, just let me know!Does the TZ170 have UPnP or Port Triggering then ?
I can not see that it does here
Opening the ports in the manner listed on that link will only allow one computer (IP) to use the open ports.
The Linksys is router and you have not mentioned what the modem is doing at that end.
Why not use UPnP here ? The Linksys does it (on the Administration page)
Most likely this needs the Respond to Anonymous Pings checked on the Security page.
9:29 PM Thursday; January 17, 2008 -
Updated to IOS 5.0.1 and now if I tap on a game icon instead of opening the game a grayish color comes over it and nothing happens. How can I get my games to work again?
Purplehiddledog wrote:
I do backup with iCloud. I can't wait until the new iMac is available so that I can once again have my files in more than 1 location without needing to rely solely on the cloud.
I also rely on iTunes and my MacBook and Time Machine as well as backing up to iCloud. I know many users know have gone totally PC free, but I chose to use iCloud merely as my third backup.
I assume that the restore would result in my ability to open Pages and Numbers and fix the problem with deleting apps, but this would also mean that if my Numbers documents still exist solely within the app and are just not on iCloud for some reason that they would be gone forever. Is that right?
In a word, yes. In a little more detail.... When you restore from an iCloud backup, you must erase the device and start all over again. There is no other way to access the backup in iCloud without erasing the device. Consequently, you are starting all over again. Therefore, it would also be my assumption that Pages and Numbers will work again and that the deleting apps issues would be fixed as well.
If the documents are not in the backup, and you do not have a backup elsewhere, the documents could be gone forever. -
I have just got a iPhone 4s and I can't get the iCloud to work, everytime I turn on auto downloads it defaults back to off, can anyone help?
Welcome to the Apple Community.
Check you are logged into your store account properly (settings > store). Also check there are no restrictions set that might be causing this (settings > general > restrictions) -
Can't get my design to work, could someone lend some guidance?
Hi,
I'm a complete newb to Labview v8.6.1. I come from the .Net world and I'm having difficulty making the transition, some guidance would be greatly appreciated.
I've attached my .vi that I came up with but I've hit a wall and I can't get this design to work correctly:
I have two buttons on my .vi, a Sample button and a Calibrate button. When I hit the sample button, I need to write out the values from my linear sensors to a file, this actually works fine. When I hit the calibrate button, I need to get the values from the sensors, store them in an array for later use. This works fine as well.
The problem I'm having is I need to use the stored values in the array in my Sample button logic which doesn't work because I don't have cases for my "False" condition.
Am I even close to the right solution here?
Thanks for any guidance.
Solved!
Go to Solution.
Attachments:
FirstDesign.zip 68 KBDo you have access to the Event Structure? It will work a lot better for GUI like this instead of polling the buttons (and using a lot of CPU).
You should look into shift registers to store your calibration array. I think the resources nyc gave should mention these somewhere in there.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines -
i can't get my ichat to work. I made an aol login but it says my password is incorrect, which i know it is not. I have a MobileMe but i can't remember the password to that. Every time I try to change my password it just changes my msn address on apple id. I have ox s lion operating system but, I couln't get the ichat to work before that either. I can use facetime tho.
HI,
If you created an AIM Name here then can you now Login Here > https://settings.aim.com/
AIM allow some other characters that alphanumeric ones but these are limited to ! @ # and the . (full stop/dot)
Is it possible that you have used other characters in the password ?
If you created an AOL Login have you used the full name ([email protected]) in the name in iChat ?
AIM never tell you directly that it is the Password.
You can get to infer it is the password when compared to other messages but it does normally refer to "Name or Password". (I just want to check that is what you are seeing)
MobileMe Name
Checking your Own Computer
Open Keychain Access in the Applications/Utilities folder
Have the Login item to left highlighted
Have the Passwords items listed if using lion lower left
Check the list on the right for your MobileMe name. It may possibly listed with an Cloud icon or the "A" created by ther pen brush and ruler icon.
It may also get listed twice or more if you have tried different passwords and asked for them to be saved.
Double click one.
In the new Panel that open change to the Access tab and check iChat is in the list if using Allow Specific items.
Return to the Attributes tab
Tick the Show Password box (Dialogue biox appears needing your Mac User Password and to Allow Once
If this password is correct then delete any other entries.
If incorrect then check others and edit one if required.
(I am hoping you will see one you recognise)
The iForgot site can be used to change the password.
It requires you have access to the linked email you used.
Or that you remember the security questions that you gave for the MobileMe name.
(Presumably you know your Date of Birth which you also get asked. )
10:03 PM Saturday; January 21, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously -
I can't get net flix to work on my Macbook pro. I used to be a window guy
I can't get net flix to work on my macbookpro.
You're going to have to give us more info than "I can't get net flix to work."
What have you done to try to get it to work?
Have you installed Silverlight?
Have you activated you Mac with NetFlix?
How are you accessing NetFlix? (Browser, Boxee....)
Exactly what is happening? -
BlackBerry z10 can't get access to mobile network, please help!
Hi, i got my unlocked z10 a few days ago and still i can't get access to mobile network. Only wifi have worked for me till now.. i used the same sim card as my old phone (where i i got access fine). I've tried rebooting and switched every setting on and off etc. Could any one please help me with this..
Since you are using the same sim I suggest you contact your service provider to check your provisioning.
Let me know if this help. -
Hi Apple, i forgot my ipad (ipad2, ios 7.04) password and i can't get access to my ipad, how can i recover my password?
Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
1. iOS- Forgotten passcode or device disabled after entering wrong passcode
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. Restoring iPod touch after forgotten passcode
4. What to Do If You've Forgotten Your iPhone's Passcode
5. iOS- Understanding passcodes
6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
Forgotten Restrictions Passcode Help
You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
Also, see iTunes- Restoring iOS software. -
I upgraded MacBook Pro (13-inch, Early 2011) to yosemite. I have no more access to Finder, App Store and some apps. Since I have no access to App Store I cannot download the missing parts. How can I get access to App Store?
Welcome to Apple Support Communities
What do you mean by having no access to those apps? Can you start up your Mac and work with it, and only some OS X apps do not work?
Anyway, what you can try is to reinstall OS X. To do this, hold Command and R keys while your Mac is starting up and reinstall OS X. You will not lose any file. -
Can't get my wired internet working
As the topic sujests, I can't get my wired ethernet working.
I'm using Mac OS X 10.5.2, I have a Linksys WRT54G router
configured to automatic DHCP.
I go into my iMac's System Preferences > Network > Ethernet.
I should be able to select DHCP from the configure menu and the router
should give me my IP address. I went into the router's settings and put my computers MAC address in, and it has assigned my iMac an IP. But on the iMac,
it doesn't come up.
Any help would be appreciated.
Thanks
Message was edited by: ShaneO'ConnorI tried that.
The way I got it to work is: I set the "configure" to manually. Then I entered the IP Address, Subnet Mask, Router, DNS Server, and Search Domains. And now it works. Thanks for your suggestion though. -
i just downloaded AOL Desktop 1.7 for Mac and I can't get my email to work. It welcomes me but I know I have new email but it doesn't recognize that I have ANY mail at all. HELPPPPPPPP Please
Hey I've been all over and can't get any help. I'm well aware its not an Apple product but its an app for Mac OS so I thought I'd try here. I bought 2 new iMacs yesterday for my parents (5K) and I'm just trying to get them some help as there in their 70's and AOL is all they know.
But hey thanks for your help,
Maybe you are looking for
-
Forgot recovery key and lost device
I no longer use any Apple products but still want to go on my Apple ID account to change some settings. Unfortunately for me I have lost the SIM card that had the number linked to my account and I have also misplaced my recovery keys so I literally c
-
Hyperlinks won't work on some (my client's) machines but are fine on others
Hi All, I'm stuck on an infuriating problem and I'm really hoping someone here may be able to help. I've created a report for a client which includes several hyperlinks to URL's. These work perfectly on my PC, also on my MacBook (in both Acrobat and
-
My phone keeps dropping calls what can i do to fix this?
My phone is dropping calls, and having trouble downloading apps over the 3G.
-
Adobe Reader XI give "Stopped Working" Error after Closing Writable PDF
I have Adobe Reader XI version 11.0.10, on a Windows 7 computer, and when a writable PDF is opened then the entire Adobe Reader program is closed it gives a "Adobe has stopped working" error. I've ran a repair with no change and Protected Mode is dis
-
Photoshop to Illustrator color shifting
First off, I have my Photoshop CS2 and Illustrator CS color preferences set exactly the same in both programs so the color should be consistent from one to the other. However, lately the colors are giving me huge hassles! In Photoshop CS2, I create C