Can't get AE clients to connect to internet-Plz help me!

I've had a home with router, wired mac's and pc's, and apple laptops for years with no problems. I removed old router and installed AE base station. I can connect to the Base Station via internet and wireless, but can't get past it to the net. I'm out of ideas.
My DSL modem from Sprint is a Prestige 660ME-61, with an address of 192.168.2.1. My "test" G5 desktop has an IP address of 192.168.1.23, subnet 255.255.255.0 and Router ip of 192.168.1.254 - as shown in system pref/network/built in ethernet configuration. This works fine with old pbx/router. I tried looking at my PBX/router settings and they use different terminology.
The AE auto setup didn't work, and I noticed it had set an ip address of 10.0.1.1 for the Base Station. I changed that to 192.168.1.x in the manual setup mode of DHCP. That generated starting and ending addresses of 192.168.1.2 to 192.168.1.200. On the Internet Connection tab, it shows IP address of 192.168.2.2, Router address of 192.168.2.254, and the DNS address from Sprint. With these paramters, I get something like "no connection to the internet" when I try to connect.
It seemed to me that I should set the router to be on the same 192.168.1.x addresses that DHCP is handing out, but when I try to change the Rounter Address to 192.168.1.254, I get a message saying that rounter address is not compatible with the lan address..
I'v worked with computers and networking for a long, long time, but I am at wits end - maybe it was the chemo! I would very much appreciate some very smart person telling me which simple setting to change to make it work! And yes, the DSL modem is plugged into the WAN port on the AE. Some of you might wonder how I'm sending this. The answer is I went back to my pre-AE configuration.
Thanks in advance!
Randy

Did you happen to allow enough time for a power recycle when switching the router connected to your DSL modem?
Modem/Router Power ReCycling
- Power-off the DSL/Cable modem, Internet Router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the DSL/Cable modem; Wait at least 30 minutes.
- Power-on the Internet Router; Wait at least 5 minutes.
- Power-on the computer(s)

Similar Messages

  • Can't get airport express to connect to internet after ISP changed my modem

    Hi. My internet service provider installed fibre optic to my house, so they gave me a new modem. Have not been able to get airport express to connect to the internet ever since. Just get the flashing amber light. Other than paying $50 for phone support, I have no idea what to do. I just use the airport so I can play music from iTunes from my stereo using airplay. I use the airport utility on my laptop.

    Does the new modem provide a Wi-Fi network? If it does, and your only goal with Express is for iTunes streaming, the Express would just need to be reconfigured to join the new modem's wireless network. Please check out the following Apple Support article for details.

  • Can't get EA3500 routers to connect to internet.

    I'm trying to upgrade a pair of WRT54G routers to a new pair of EA3500 routers, but I cannot get the modems to connect to the internet.  I've tried both of the new modems, and multiple connection cables between the Charter cable modem and the router, but I have yet to get a usable internet connection.  I'm able to get to the router settings by browsing to 192.168.1.1, but the settings show there is no internet connection.  My old routers still work great if I switch the cable modem over to them, so the problem is not likely with the modem or cable connection.  Any suggestions on what might be going wrong?
    Rick
    Solved!
    Go to Solution.

    I had tried cycling the modem multiple times, but this time I gave it a full 5 minutes and I was finally able to connect.  Thanks!
    Rick

  • I can't get my router to connect. Someone pls help me.

    I've been trying for like 6 hours to get my router to work. It's recognised but it can't connect to the internet it did yesterday but now it won't. Also I've been trying to find my network key and the blank username and admin for password doesnt work. The model of my router is a WRT54GS.
    Message Edited by tgamerlegend on 03-25-200711:07 AM

    1st reset the router back to it's default settings by pressing the reset button at the back of the router for 20-30 seconds. Then unplug the power of the router for 10 seconds and plug it back in.
    Then to reconfigure the router from scratch including setting up your wireless settings... I recommend using a fairly easy to use software called EasyLink Connect. You can download this off the internet (by bypassing the router and connecting to the modem) from this website: www.linksys.com/easy

  • Wifi Problem - can't get iPod Touch to connect to Internet

    I've seen lots of posts and discussions around this issue but cannot seem to nail down a solution. I have no security or encryption whatsoever with my wireless router & network. Other devices can connect wirelessly with no problem but my iPod Touch, although it shows that it is connected to my wireless network with all the proper DNS settings, it cannot access the internet. Of course, none of the wifi-based apps will work as a result.
    Based on what I've deduced so far, I think the issue is that my brand new iPod Touch does not like my older Linksys WRK54G wireless router. That said, my brother's newer iPhone picked up my wireless network fine recently??
    Does anyone have any advice? Thanks.

    I have read all the posts and did all the numerous solutions/suggestions for 2 days now and what worked for me is this:
    I went to Dlink online and went to Wireless connection settings to change the SSID name as if I am using my router for the first time, then changed it to WPA 20 characters! then saved the settings. Do this on the original PC (in my case, a desktop linked to the router via Ethernet cable as I have 2 laptops running
    from that router as well. Note, before doing the "Save the settings"
    above, I reset the Dlink router (by putting a pin at the back of the unit,
    then turning it off and on including my separate Netcomm modem.
    You then go back to your Ipod touch/ Settings and Choose the new Network Name.GOOD LUCK.

  • I've tried 3 different hifi's but can't get my iPod to connect....HELP

    Please help me.....my iPod won't connect with my hifi.
    It's a new iPod touch, software version 4.3.5 and the hifi is a new Sony CMT-CX5Bip.
    This is my 3rd hifi, having returned 2 others thinking they were faulty!
    Is it my Touch?
    What can I do?

    Does the documentation say it is compatible with the a 4G iPod with iOS 4.3.5? I Googled but could not find any info on compatibility.

  • Can't Get Sony PSP To Connect to Internet via my WRT54G Wireless Router

    Hi:
    I hope someone can help who was able to do this.  I have tried everything and the PSP will not connect to my network.  I use WEP security and a MAC address filter.  I even turned both of these security features off and it still won't connect.
    What am I doing wrong?
    Thanks,
    Paul

    I have version 1.1, but it has the latest firmware revision 4.21.1 of January 30, 2007. The firmware notes state it supports up to hardware version 3.  So you think this router won't work with the PSP because it is too old?

  • Can't get Airport Extreme to connect to Internet

    I have a D-Link 320T ethernet modem. This works fine connected straight into my Mac, but as soon as its connected to the Airport I loose my internet connection. Its seems to be something to do with my setup, but I'm clueless as to what.
    My airport seems to be transmitting something, as my Nintendo DS can pick up the Network name I have created, but it gives me this message "connected to access point, but unable to connect to the server", error code 52100.

    Hi Bidge,
    Welcome to the Apple.com user discussion boards!
    Do you have ADSL? Have you setup the Airport Extreme to establish the PPPoE session with your ISP?
    To configure this, please refer to this Apple article - http://docs.info.apple.com/article.html?artnum=166636

  • Can not get my URL to work in AS3 – plz help.

    I have 3 movie clips that each have a button nested within. I need to make this button an active URL link to a web page. I can't seem to get it to work.
    EXAMPLE:
    The first movie clip name is:
    myBalzacMC
    The button nested within this particular MC is:
    balzacURLBtn
    Everything is brought onto the stage dynamically.
    With the code I pasted below, is this enough information for someone to help me? I have also pasted a
    I also get this error:
    TypeError: Error #1010: A term is undefined and has no properties.
    at ParisMap3_fla::MainTimeline/frame1()
    Part of the code:
    function showOrder(evt:MouseEvent):void {
    if (mc.numChildren>0) {
    mc.removeChildAt(0);
    addChild(mc);
    switch (evt.target.name) {
    case "b1" :
    var myBalzacMC:BalzacMC = new BalzacMC();
    mc.addChild(myBalzacMC);
    mc.y=175;
    balzacMCTween=new Tween(mc,"x",Strong.easeOut,1050,638,1,true);
    balzacMCTween2=new Tween(mc,"alpha",Regular.easeIn,0,1,1,true);
    break;
    case "b2" :
    var myCastilleMC:CastilleMC = new CastilleMC();
    mc.addChild(myCastilleMC);
    mc.y=175;
    castilleMCTween=new Tween(mc,"x",Strong.easeOut,1050,638,1,true);
    castilleMCTween2=new Tween(mc,"alpha",Regular.easeIn,0,1,1,true);
    break;
    case "b3" :
    var myDeVignyMC:DeVignyMC = new DeVignyMC();
    mc.addChild(myDeVignyMC);
    mc.y=175;
    deVignyMCTween=new Tween(mc,"x",Strong.easeOut,1050,638,1,true);
    deVignyMCTween2=new Tween(mc,"alpha",Regular.easeIn,0,1,1,true);
    break;
    //________ URLs_______________________
    mc.myBalzacMC.balzacURLBtn.addEventListener(MouseEvent.CLICK, goSite1);
    function goSite1(evt:MouseEvent):void {
    navigateToURL(new URLRequest("https://www.phgsecure.com/IBE/brandRedirect.ashx?propertyCode=PARCP&rateCode=MKTPAR&brandC ode=PV&iataNumber"));
    mc.myCastilleMC.castilleUrlBtn.addEventListener(MouseEvent.CLICK, goSite2);
    function goSite2(evt:MouseEvent):void {
    navigateToURL(new URLRequest("https://www.phgsecure.com/IBE/brandRedirect.ashx?propertyCode=PARCP&rateCode=MKTPAR&brandC ode=PV&iataNumber"));
    mc.myDeVignyMC.deVignyURLBtn.addEventListener(MouseEvent.CLICK, goSite3);
    function goSite3(evt:MouseEvent):void {
    navigateToURL(new URLRequest("https://www.phgsecure.com/IBE/brandRedirect.ashx?propertyCode=PARDV&rateCode=MKTPAR&brandC ode=PV&iataNumber"));

    No errors found with the trace.
    I think it has something to do with the renaming of MC's to make the switch statement work properly?? Does that make sense?
    myBalzacBtn.name="b1";
    myCastilleBtn.name="b2";
    myDeVignyBtn.name="b3";
    function showOrder(evt:MouseEvent):void {
    if (mc.numChildren>0) {
    mc.removeChildAt(0);
    addChild(mc);
    switch (evt.target.name) {
    case "b1" :
    myClickIconsMC.visible=false;
    var myBalzacMC:BalzacMC = new BalzacMC();
    mc.addChild(myBalzacMC);
    mc.y=175;
    balzacMCTween=new Tween(mc,"x",Strong.easeOut,1050,638,1,true);
    balzacMCTween2=new Tween(mc,"alpha",Regular.easeIn,0,1,1,true);
    break;
    case "b2" :
    myClickIconsMC.visible=false;
    var myCastilleMC:CastilleMC = new CastilleMC();
    mc.addChild(myCastilleMC);
    mc.y=175;
    castilleMCTween=new Tween(mc,"x",Strong.easeOut,1050,638,1,true);
    castilleMCTween2=new Tween(mc,"alpha",Regular.easeIn,0,1,1,true);
    break;
    case "b3" :
    myClickIconsMC.visible=false;
    var myDeVignyMC:DeVignyMC = new DeVignyMC();
    mc.addChild(myDeVignyMC);
    mc.y=175;
    deVignyMCTween=new Tween(mc,"x",Strong.easeOut,1050,638,1,true);
    deVignyMCTween2=new Tween(mc,"alpha",Regular.easeIn,0,1,1,true);
    break;

  • How can I get the ipad to connect to itunes 10.6.3?

    How can I get the ipad to connect to itunes 10.6.3?

    The iPad mini requires iTunes 10.7 or newer to sync.
    (82182)

  • I get a message the message " Can not get mail. Not connected to server" Yet I am connected with Wi-fi and can access all other websites. Can you advise? My iPad is only a month old!

    Has any one experienced not being able to send mail and only receiving some? I get the message " can not get mail. No connection to the server! " Yet I get some mail but can not send out any. My iPad is only 1 month old! It worked perfectly for about 10 days.
    Thx
    Agnes

    Hey agnesfromcopenhagen k,
    Thanks for the question. I understand you are experiencing issues with Mail on your iPad. The following resource provides some troubleshooting steps. What kind of account are you using? Some internet providers require that you be connected to your home Wi-Fi (or for work accounts, inside your corporate Wi-Fi/firewall). Also, some email accounts require two-step authentication. For more information, see this resource:
    iOS: Troubleshooting Mail
    http://support.apple.com/kb/TS3899
    Thanks,
    Matt M.

  • How can I know which clients are connected to my network through express and which are connected through extreme?

    I have an airport express extending, through wireless, a network provided by an airport extreme. How can I know which clients are connected to my network through express and which are connected through extreme?
    Here you can see both routers:
    I would expect to some clients connected to the express, other than the extreme. And that's all I see: only the airport extreme appears as client of the airport express.
    Below, one can see the summary of the config for both routers.
    Would somebody explain it?
    Thanks,
    Marcelo
    Message was edited by: Marcelão

    please disregard this answer.
    Message was edited by: Marcelão

  • Hi I can not get my printer to connect to the internet.

    Hi
    I can not get my printer to connect to the internet. it is connected to my network according to wifi test printout but my computer can not find it.
    When I try to download apps directly from the printer it says that it is not connected to the internet.
    I have an airport extreme + 3 airport express a macbook pro and printer is an HP 7510e
    I see the printer on the first page in the airport utility when I click on my airport extreme.so it is online but nothing happens when I try to print.
    Please help me

    Hi all,
    Guess I understand what is going on as I'm also experiencing the problem.
    Basically the issue is about the iPhone 4's personal hotspot.
    I'm trying to hook on personal hotspot to my toshiba laptop but it couldnt work as the connection is limited to local only without Internet access.
    The hotspot works well on other laptop and I-devices, but not my toshiba...
    Hope to get assistance here. Thanks

  • How can I get my iPad to connect the love film app to my Apple TV?

    How can I get my iPad to connect the love film app to my Apple TV?

    Have you confirmed that the app supports AirPlay? If it doesn't, then you'll have to connect via screen mirroring. See:
    http://support.apple.com/kb/HT4437
    and
    http://support.apple.com/kb/HT5209
    Regards.

  • Just got an iPhone and can't get iTunes Match to connect. Keep getting a message that I'm not subscribed, but already did on my pc. Any ideas?

    Just got an iPhone and can't get iTunes Match to connect. Keep getting a message that I'm not subscribed, but already did on my pc. Any ideas?

    You must be signed into the mobile iTunes Store using the same Apple ID you used to originally purchase iTunes Match. On the iOS device go to Settings > iTunes and App Stores and tap the Apple ID. Log out, then log in with the correct ID.

Maybe you are looking for

  • Installing DI on Linux impossible : libclntsh.so does not exist

    Hello, We have an ECC6 ehp4 system (Central Instance) running on HPUX Itanium (B.11.23). The database being Oracle 10.2 : Database Client Library : OCI_102 (10.2.0.2.0) Now, we are trying to add a dialog instance running on a Linux Suse application s

  • Creative Vision:M, best video conversion program(freeware or softwar

    I recently got a creative vision:m and love it, but i cannot figure out whether or not my recently purchased "23 Copy DVD Gold Edition" software is worth the fifty bucks i had to pay. Does anyone know of online freeware etc that works well and produc

  • Widescreen 16:9 Project Option

    VC3 should have the option for users to set whether they will be producing a 4:3 project or a 16:9 project. The supplied graphics and preview windows would "adjust" themselves accordingly. Just about everyone is producing at least some, if not all, o

  • How do you auto populate a dynpro field when hit key while in other fields?

    This is a dialog programming question for a custom dialog program (it is NOT an SAP program). I have a dialog program that neds to be changed to accomodate the following. i have searched SDN and can not find anything to resolve this issue. I have a s

  • Handing off a DPS file

    I want to start creating DPS files for outside clients, but I do not want to handle the publishing aspect (it's their publication that they are selling, so they need to set up their own merchant account.) Am I able to create a file (or suite of files