Can't get Airport Express back onto my wireless network???

Just returned from a trip where I had successfully used my AE in temp accommodation. Now I can't get the thing to rejoin my home network. I've reset it time after time, I go through Airport Setup Asst and get to the bit where it says it's updating the AE, congratulates me on setting it up - but the thing never rejoins and all I get is the amber blinking light. Once this happens it disappears off the network until I again, reset to factory settings.
I have tried entering WEP equiv passwords as well as the ASCII but am not sure which one to use now - totally confused. I have another AE on the network which is working fine. I must be missing something unless the thing has gone u.s?
Any ideas would be gratefully received.
Cheers
Chris
iMacs, Intel 20 inch 2.0 with 1.5 gig ram Mac OS X (10.4.9)

Hi Dan
I have posted a new topic on this because I feel strongly about it.
Here's a copy and paste of what I said:
"I have spent literally the equivalent of 3 full days, configuring, reconfiguring, re-installing, setting up, un-setting up, scouring the internet, phoning people, taking trips to the Apple Store to find a solution. All a total waste of time. Why? Because until there is an update to cure the problem, the Airport Extreme BS will not function properly when used in an environment other than a basic setup.
My network at home consists of 3 XP PC's, two Airport Expresses, and 5 Macs of various models. Until I removed an Express to use it on a trip, all of it worked well. When I came to return said Express into 'the fold' - that's when the trouble started. Mainly that, unless I had security switched to NONE, I couldn't connect the Expresses to the Base station, and my HP PSC2510 wireless printer would not connect either.
If you are anything like me, you will have been through every single combination of setups, restarts, reinstalls you name it. I got conflicting info about the level of security from the Admin utility - sometimes it would report WPA, others it would say WEP.
Cut a long story short, I finally returned the BASE Staion to the Apple Store and got a replacement. I had narrowed it down to that component only. Everything else on the network "seemed" to be fine.
I wondered whether it was a solitary, faulty AEBS, and by replacing that, it would eliminate the problem. In theory.
Brought home new AEBS but this unit also suffered collossally unreliable/unsuccessful connections from Printer, Expresses and one XP laptop.
I have been to the Moon and back with Hewlett Packard trying to work out what could have happened - overnight - to this normally fail-safe wireless printer. No clues, all seemed to be set up correctly. But it WOULD NOT JOIN THE NETWORK!!!.
So, as any mad (as in angry) scientist would do, I set up a "Control" experiment. Keeping everything as it was, all I changed was the AEBS. I swopped the AEBS for my older white AEBS (flying saucer). Guess what?
Within seconds, all connected. Including printer, Expresses, and XP PCs.
All working perfectly. Wrote down all the settings to check exactly the same as on the new (n) AEBS - identical. Swopped back - same problems. No way would it work.
I am no Network expert but have a feeling that it has a problem managing/distributing/assigning IP addresses. Dunno, just a hunch because the printer would connect fine when connected to AEBS by ethernet cable.
So I am now going to return the new AEBS to Apple and get a refund. I don't have time for this and I suggest not many people do.
So if you have a problem like I did, it might be an idea to try another router or eliminate it somehow and check your settings.
I hope this helps.
EDIT:
Looking again through a lot of posts on here - I would estimate that they are pretty much linked to the same problem - a few are reporting problems after connecting to different ISP then not being able to get it working again, some saying they can't get a single solitary PB to connect but al the others do. It all rings bells here! I am sure it's an IP problem (but what do I know) I would love someone to see into this. I doubt whether Apple will come up with something before Christmas - let's hope they prove me wrong eh?
Anyone know of a good, reliable wireless router that also allows external HD sharing?
Cheers!
Chris"

Similar Messages

Can't get Airport Express to connect to my network

I have a netgear wireless router, and the when I plug in the aiport express, it just blinks yellow. When I run the Airport express assistant, it gives me a warning that windows is not managing my wireless network. This is very frustrating!! What can I do?

I'm sorry you are having problems. When I cabled directly to the Express from my computer and ran the assistant it worked perfectly. After disconnecting the calbe, it connected wirelessly to my existing network. I am running an Aiport Extreme for my base station, I don't know if that makes a difference. When you run the assistant do you select "Join existing network"? There is a great post on here somewhere with other instructions on setting up the Express a different way. Sorry I can't be more helpful.

How can I get airport to connect automatically to wireless network?

I temporarily switched from a DSL internet provider to a cable provider, and then back to my old DSL Internet provider. My g5 iMac computer connects to the network through a wireless Belkin router.
Since I switched Internet providers, every time I turn on my computer, it no longer automatically connects into the wireless network. Instead, to connect I now have to manually select the network.
I'd really appreciate tips on automating this step. My kids use this computer and due to parental restrictions, they do not have rights to connect to the network.

Hi there,
Strictly speaking changing how the internet is coming into the wireless router should not affect the wireless and how machines connect to it, but however to get you out of a hole I would say create a new Location for your home and start again.
Basically,Disable your wireless first, then in your network settings there is a drop down box at the top of the panel where you can change and create new locations. Create a new one, then select it and click Apply. Now enable your airport and connect to the wireless, once that is done you should be good to go.
Hope that helps,
Callaghan001

Can't connect Airport Express to my main wireless network, just my guest account.

I go to join my Airport Express to my wireless network so I can play music from Itunes to my sound system in my living room. That is all I want to use it for at this point. I pull up a list of the networks available, and my guest network shows up on the list, but my main network, which all my computers and Iphone is connected to, isn't on there. I have a Linksys E3000 with a guest account set up trhough it. Windows 7. I called tech support and they said something about a hidden setting. I went and checked and couldn't find anything about this. Also, when people come over they can access my main wireless account with my password.

Hi JWHITHAM and welcome to the forums!
Have you tried manually adding your wireless network to the iPod touch? Mine does the same too sometimes and I just add it manually. So far it works.

HT1414 i backed up tha data on my iphone before i unlocked and restored as "new." how can i get the data back onto my iphone?i backed up tha data on my iphone before i unlocked and restored as "new." how can i get the data back onto my iphone?

Hi,
I wanted to unlock my at&t iphone 3gs that i had for 3 years. i was told to back up the data on my phone and then restore it as new. now i don't have any data i had before it was restored. how can i get that data back onto my iphone 3gs? can i put that data on my ipad?

Is it an iTunes backup or an iCloud backup? If iTunes, connect the iPhone, right click on the name of the iPhone under the DEVICES section in iTunes. Click on Restore from Backup.
If iCloud, on the iPhone go to Settings > General > Reset > Erase All Content and Settings. When the device powers back on, you will see the original setup screens you saw when your iPhone was fresh out of the box. One of these screen asks you if you want to restore. Choose Restore from iCloud backup.

I deleted my music through the "manage storage" section in the options to make room for the ios update awhile back. Now I can't get any music back onto my device through itunes. (I've tried restoring the device twice to no avail)

I deleted my music through the "manage storage" section in the options to make room for the ios update awhile back. Now I can't get any music back onto my device through itunes. (I've tried restoring the device twice to no avail)

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

New router now can't get airport express to work

Att installed a new wireless router.
Everything else seems to be fine but can't get airport Express to communicate with My MAC. Green light on airport device. Just downloaded OX on Mac recently.
Any suggestions would be appreciated!

Reset the Express to factory and start over.. this is always required when you make major network changes.

Using Airport Express to extend my wireless network

I recently purchased a Time Capsule but found that I could not see the wireless signal from my bedroom. To solve this I purchased an Airport Express to extend the range. I plugged the AE into an outlet in my bed room and set it up to join my existing network. Everything looked fine from the point of view of the Airport Utility. Unfortunately my iPod Touch still can not see my wireless network from my bedroom. I new iPad can see it but the signal is very weak, even when I hold it right next to the AE. Is there a setting I missed?

Rick, welcome to the discussion area!
I plugged the AE into an outlet in my bed room and set it up to join my existing network.
You need to configure the AirPort Express to "Extend a wireless network". The AX does not provide any additional wireless coverage when it is set to "join".
First, you need to check a setting on your Time Capsule as follows:
AirPort Utility > Manual Setup > Wireless tab (below the icons)
Make sure there is a check mark next to "Allow this network to be extended"
Update to save any changes
On the AirPort Express move it close to the Time Capsule for configuration:
AirPort Utility > Manual Setup > Wireless tab
Wireless Mode = Extend a wireless network" (Hold down the option key on your Mac if you do not see this choice appear when you click the selection box).
Wireless Network Name = Same name as your Time Capsule Network
Check mark next to "Allow wireless clients"
Security = Same setting as your Time Capsule
Password = Same password as your Time Capsule
Confirm Password
Update to save settings
The AirPort Express can only "extend" what it "receives". Most users position it too far away from the main router and consequently, the Express extends a weak signal. Try a location that is about 1/2 to 2/3 the distance between the Time Capsule and the area that needs move coverage. Then experiment a bit to find the best signal.
Post back on your results.

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

Airport express failing to extend wireless network

Have got an airport extreme connected via ethernet to my Virgin Media hub (hub is in modem mode). Also have an airport express to extend the wireless network. Setup has been working perfectly for over a year, then this weekend, literally no settings have been changed, and airport express is giving me a status message of "This airport base station was unable to extend the wireless network. Make sure the wireless network you're trying to extend was setup and is working correctly, that you entered a matching wireless network password into this device and that this device is in range of the wireless network"
I have reset to factory settings 3 times now and whilst it goes through the initial setup, i always get the same status message. Front light is green.
The express version I'm using is the 2012 redesigned version, looks like a white Apple TV and it has the latest firmware. I've tried configuring via my MBA, windows desktop pc (windows 7) and ipad, nothing works
Any ideas?

You have to think of the Express devices as matching pairs when you have one set up to create a wireless and the other to extend it. Here, I assume that you still have the extending Express set up to extend the network.
Power off both AirPort Express devices. The power down order does not matter.
Wait a minute
Power up the main AirPort Express.....the one directly connected to the Virgin hub....and let it run a full minute
Then, power up the extending Express
Check the network and report on your results

Airport Express won't extend wireless network

I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

Can't get Airport Express to work with Windows

I got a used Airport Express to use as a wireless print server. I got only the Airport Express; no manuals or CD's or anything. I have been reading through the manuals and everything online, but I can't get anything to work. It seems like I need to get the Airport Express Assistant, but I can't find it. I got the Airport Admin Utility, and that installed fine on Windows Vista. Then I installed what I thought was the Express Assistant, and it just seemed to change the Airport software in the start menu, but I still don't have the Assistant, only the Admin Utility. Anyway, I open the Admin Utility and it opens the Base Station Chooser. There is nothing there, so I rescan, and it seems to do nothing. It doesn't find anything anyway.
Where do I go from here? I am kind of stuck. I am trying this on a Windows Vista PC which is hardwired to a Linksys WRTSL54GS router. I have the airport express plugged in and the light is flashing Amber. I have a HP psc2410 plugged into the airport express that I would like to print wirelessly to.
Thanks for any help.

You don't necessarily need the AirPort Setup
Assistant, you should be able to set up the AirPort
Express Base Station (AX) with the AirPort Admin
Utility...as it is a much more powerful tool. You
need to make sure that you are using the version for Windows. At this
time, the AirPort software is only supported for
Windows 2000 or XP. A Vista-version has not been
released.
I suggest the following...
- First, perform a "factory default" reset on the AX to get
it back to it's original "out-of-the-box" state.
- Next, temporarily connect your computer directly,
using an Ethernet cable, to the Ethernet port on the
AX during the set up phase.
- Then set up the AX as a "wireless client."
I have this same problem. I have a Vista Windows notebook and I am trying to get airport working to play music wirelessly through my home stereo. The "base station chooser" software does nothing on my Vista notebook.
I used a friend's MacBook and was able to set up the airport as a client so I can see it listed in my Dlink router DHCP Client Table. The airport express box is plugged in, has a steady green light and everything looks good except there is no option to choose "computer" or "home stereo" speakers in my iTunes. i installed the airport express CD including the itunes it came with.
Any ideas how to get this working on vista? Previously i had the newer version of iTunes 7.1 installed and the airport express CD told me it couldn't complete the install because a newer version of iTunes was installed. I uninstalled the iTunes and reinstalled the CD including the iTunes version 4.
Help!
Sony Vaio Windows Vista

Can't Get Airport Express to Connect to my D-Link DIR-655?

Here's what I did - I should point out all I wanted to do was connect my PC based iTunes upstairs with my stereo system downstairs. First I tried to have the Airport Express join the d-link wireless network. It joined but playback was choppy and I could not get it to work. Next I tried my solution for the Xbox Live issues we've had, which is to go with a NetGear home wiring etherenet, and try to get it on that, but the network never saw the Airport Express. Last, I simply set up the Airport Express as a second wireless (but only "local") network in the house, and so far it works like a charm - no choppy plyback, and I use my iTouch with the Remote app to control iTunes from anywhere in the house. So perseverance won out. However, it really was a bummer that the other solutions did not work, and proved once again to me the "glitchiness" of Apple products.

I'm sorry you are having problems. When I cabled directly to the Express from my computer and ran the assistant it worked perfectly. After disconnecting the calbe, it connected wirelessly to my existing network. I am running an Aiport Extreme for my base station, I don't know if that makes a difference. When you run the assistant do you select "Join existing network"? There is a great post on here somewhere with other instructions on setting up the Express a different way. Sorry I can't be more helpful.

Can't get airport express to connect to internet after ISP changed my modem

Hi. My internet service provider installed fibre optic to my house, so they gave me a new modem. Have not been able to get airport express to connect to the internet ever since. Just get the flashing amber light. Other than paying $50 for phone support, I have no idea what to do. I just use the airport so I can play music from iTunes from my stereo using airplay. I use the airport utility on my laptop.

Does the new modem provide a Wi-Fi network? If it does, and your only goal with Express is for iTunes streaming, the Express would just need to be reconfigured to join the new modem's wireless network. Please check out the following Apple Support article for details.

Can I use my airport express to extend a wireless network with a non-apple router?

I have been trying to extend my wireless network in my house. Right now I have a dsl modem/router provided by Century Link and an older AirPort express (not sure how old but it uses AirPort utility v5.6). I want to be able to share my printer and use AirTunes. Currently I have the AirPort plugged into the router and setup to create a new wireless network. I would like to combine them so I don't have to switch between to print and play music. I am not really sure where to start or if it even possible. Any info would be great!

If you keep the Express connected using Ethernet and configure the Express to "Create a wireless network" using exactly the same wireless network name, exact same wireless security and same wireless password as the Century Link network.....everything will behave as one "big" network, and you will have additional wireless coverage near the Express.
If you do not need extra wireless coverage, you can turn off the wireless on the Express.
The Express must be in Bridge Mode.
Most users know the name of their wireless network and password, so the really tricky part of doing this is that you must know exactly what type of wireless security settings the Century Link router is using....and then match up the same settings on the AirPort Express.
If the settings do not match up exactly, then you wind up with two separate networks that will each require their own log on.
If you can check the setting for wireless security on the Century Link router and provide that information to us, we can tell you how to set things up the way that you would like.

Can't get Airport Express back onto my wireless network???

Similar Messages

Maybe you are looking for