Can't get Airport Extreme card to work in G5 Powermac

I'm probably being a dummy, but I need some help.
My main computer is just under two years old and has funcioned on a network through ethernet. Internet access comes through cable and I have a Linksys wireless router. My G4 ibook has operated on this network with an airport card quite successfully.
I decided to get rid of some cables and put the G5 on wireless. I installed an Airport Extreme card, connected the antenna. The Network Status panel tells me that the Airport card is turned on but not connected to a network. The signal indicator on the menu bar is greyed out.
Any attempts I have made to find a network signal or configure the card seem to be doomed.
What am I doing wrong?

IF those are the only two options, I don't know what it could be.
Going backwards,
Double check your antenna on the card.
Pull up Software Update, perhaps an update will come up for this situation.
Boot to an OSX install disk, Run Disk Util and run a Disk Repair then Disk Permissions Fix. Unlikeley bit worth a shot
Return the card?
Sorry man...

Similar Messages

  • Can't get Airport Extreme Card working

    I recently purchased a refurbished Airport Extreme Wiresless card for my EMAC from the Apple Store, installed it, but now when I try to configure the network connection, Wireless Airport is greyed out. I don't have the Extreme Station and didn't think I needed it, but I cannot figure out to make the connection to my existing wireless cable modem router in my house. Any help in this situation would be greatly appreciated!
    Thanks, SBeck

    Technoqueen,
    Welcome to the Apple Discussions!
    Does the card appear in Applications> Utilities> System Profiler under the Network> Airport Card heading? There have been a number of reports over the years from posters here in the Discussions to the effect that the Airport Extreme card is an extremely tight fit in the eMac. The card can fell as if it's fully seated in the slot, yet not actually be all the way in. It takes a surprising amount of force to fully seat the Airport Extreme card that last fraction of a millimeter; you need to push the card until just short of where the 50-lb eMac is shoved away from you on your work surface.

  • I can't get airport extreme to work with iPad

    I can't get airport extreme to work with iPad

    Ok, thanks for clarifying that for me. We have two distinctly different printing problems. Let's try tackling them one at a time if you don't mind.
    In order for the iPad to print to a printer it would either have to be AirPrint-enabled or you would need another solution, like PrintCentral for iPad or Printopia. Unfortunately, I don't believe your Canon printer is AirPrint-enabled. There aren't many printers on the market that currently are. All of them, that I am aware of, are HP devices.
    Now for the PC. I would go with what you have already suggested and that is try disabling either the Windows or third-party software firewall. Which version of Windows is it running? Just in case it's XP, here are two excellent iFelix articles on how to do so with or without using Bonjour.

  • Can a "bad" Airport Extreme Card work intermittently, i.e.

    work sometimes and then suddenly disconnect and reconnect? I'm having trouble with Safari crashes, and slow or no page loads... it was implied that the Airport Extreme Card may be not working properly. Can this happen?
    I figured it either works or don't work, but maybe it's slowly dieing? I don't know.
    Anyone with experience with the card dieing or being intermittent? Is there a good way to test it?
    Thanks for any observations.

    Well here's a new one, but I might be speaking too soon. I certainly hope not!
    The AirPort checked out just fine at the Apple Store, and sure enough within an hour back home my connection/browsers crashed. I shut down the computer and unplugged the gateway. It ran smooth for three whole hours before crashing this time (the longest time on record).
    There's been one more thing in the back of my mind, and before calling the DSL company to return the gateway I figured I'd give it a try.
    I unplugged the KENSINGTON wireless optical desktop for Mac, keyboard and mouse with the RF receiver, and guess what?
    I haven't crashed in " 10 entire hours"!!!!!!!!!!!!!!!! BIG RECORD!
    Who would know? Not I.
    I emailed Kensington Support and asked whether the RF reciever might interfer with a wireless connection via airport, but I don't expect a reply. Niether a reply from the Yahoo!SBC/DSL support, because nothing, i.e. no video works with Mac OSX on their homepage. Bummer! But that's another problem I CAN ignor.
    Has anyone here ever heard that a wireless keyboard and mouse can mess around your airport connection?
    So for so good.
    G5 dual 1.8   Mac OS X (10.3.9)  

  • Airport extreme card not working with leopard / G5

    I just upgraded my PowerMac to leopard (G5 dual 1.8, 3 gigs of ram, 250 GB HD). I bought it new in December 2004 from apple. Previously I had been using a USB adapter to connect to my wireless internet at home (Linksys WRT54G). This device does not support leopard so I got an airport extreme card from gainsaver.com.
    The Airport extreme card is configured properly as far as I know but it will only connect to my network for about 5 seconds then it drops. The USB adapter worked perfectly in the same spot and my macbook right next to it works fine as well.
    1. Could it be a bad Airport extreme card?
    2. Is this a known issue? And possibly be resolved with the 10.5.2 update?
    It is a fresh Leopard install with no updates as I can not connect it to the internet to get them. Any help would be very much appreciated.
    Message was edited by: anthonylkelly

    Hi, I have the same machine (4 ram slots?) have you got the connector for the aerial that connects to the motherboard attached to your airport card. Mine works a treat.

  • Airport Extreme Card Not Working Properly (Web Browsing Slow)

    Hello people of apple discussions,
    I have the original MacBook Pro with Mac OS X 10.5.7 installed on it. And I have a problem, my airport extreme card is not functioning properly like when I go on the internet, it comes up with the server "www.google.com" cannot be reached or the same with Yahoo! Back when it had 10.4 it was functioning properly with very high speeds. But, all the other PCs in the house gets good internet even my iPhone and the router is functioning properly. It's been like this since for about 6-8 months and i am very upset with my mac!:|So can I have some help or any suggestions!
    Message was edited by: mr.ts

    Have you tried contacting your ISP? Sometimes they can help you optimize your settings. Such as DNS server numbers. I had a simullar problem and found out my DNS settings were wrong.
    Do you have other computers that use the wireless single? If not you might look into your router to see if maybe something is wroung with it. You can always go to a wifi hotspot or a friends house and see how the connection is there. If it seems normal then you know it is your ISP or your router. If not then it might be a laptop problem.

  • Is there a way to update firmware on airport extreme card to work with "n"?

    I have a airport extreme card in my G4 Powerbook and want to know if I can somehow update that card to make it compatible with the new "n" wireless standard?
    Even if I can't, should I update the firmware and if so, how do I go about doing it?
    Thanks!
    Dan

    No there is no software update that will give that card 802.11n capability.
    Your PowerBook can join an 802.11n network as long as that network is configured to operate in an 802.11b/g compatible mode. You will not get the speed benefits of 802.11n since your PowerBook will be operating at 802.11g.
    You may want to take a look at QuickTek's products.

  • Can't get dedicated graphics card to work.

    I can not get the dedicated graphics card to work on my laptop. I spend my night installing and uninstalling drivers, wich none of them seem to work.
    To check the card if its working, I dissabled Intel HD Graphics adapter and left the AMD, instead of getting the dedicated card to work I got "Microsoft Basic Display Driver".
    Please help me....
    EDIT: I only reinstalled AMD drivers, I didn't touched the intel ones since they work.
    My laptop: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c04089426&tmp_task=prodinfoCategory&cc=us&dlc=en...

    HI FXV,
    Thank you for your query, I will do my best to assist you.
     I understand  you have already uninstalled and then downloaded and reinstalled the recommended driver to no avail.
    Here is a link to a post by @Paul_Tikkanen  that may also help.  beta driver.  This seems to have solved the issued for someone else.
    Have you tried running the HP Support Assistant to aid with updates and resolving issues.
    Have you tried Using Automated Troubleshooting (Windows 8) to assist with this difficulty.
    You could also try Refresh Your PC to Resolve Problems (Windows 8) to resolve issues.
    That last thing I can suggest before referring to HP support is a recovery back to factory. Performing an HP System Recovery (Windows 8)
    During the recovery process you will get a prompt to backup your personal files to prevent data loss, if you have not done one recently, I suggest you do one now.
    Restoring Files that were Backed Up Using HP Recovery Manager (Windows 8).
    If none of the above has resolved the issue then I suggest contacting HP support for assistance. They have the ability to remotely access your system to help locate and resolve issues.
    Please call HP technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region HP Technical Support Sitemap.
    Please let me know the outcome.
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • Can't get Airport Extreme and Express to join same network

    I recently bought an Airport Extreme so I could create a wireless network with my Airport Express. THis way I could browse the internet and stream music to my stereo at the same time. After spending hours trying to get both AP Extreme and Express linked together in a WDS network, I have failed time and time again. I have no problem setting the AP Extreme as the WDS main. My iMac and laptop connect to the AP Extreme just fine. I can set up the AP Express to stream music via iTunes to my stereo without problems. But to get them working together in the same network has got me stumped.
    I've set the AP Extreme as WDS main and Express as WDS remote. They are both set to same wireless channel. Where am I going wrong? Is it a 802.11n/802.11g compatibility issue?
    I'd appreciate any insight. Thanks.

    adrian,
    I have done this a dozen time today with different base stations like yours.
    The only thing I can think of is this:
    1. With the WDS Main, make sure you have the address of the Remote in the box.
    2. With the WDS Remote, make sure you have the address of the Main in the box.
    3. Make sure both base stations have the same network name in the wireless tab.
    Then restart both base stations.
    Let us know what you find out.
       Joseph Kriz

  • I am unable to get Airport Extreme WiFi to work with Windows 8 Sony Laptop

    My Airport Extreme WiFi works with my Mac Book Pro, iphones, ipad and DVR's, but will not work WiFi with my Sony VAIO laptop running Windows 8.  Although it does work with the laptop using a ethernet cable.  Has anyone else had this issue and can you please tell me how to resolve the problem?

    Windows can have issues with the wireless name.
    Make sure the name conforms to windows standard.
    Short, 2-20 characters
    No spaces,
    Pure alphanumeric.
    eg AEwifi is a good wireless name.
    Fred Blog's Airport Extreme Wireless87AD34 is a really bad name.
    Test also by removing the security and just see if you can connect if the short name doesn't help.
    WPA2 Personal is really the only security worthy of the name and the password should be mix of upper and lower case plus numbers.. keep it pure alphanumeric also.
    Set fixed wireless channels at least for 2.4ghz may help, depending on your location geo standards wise.
    Test 11, 6, 1 in that order. With no security briefly. And a short name. (different name on the two bands is also a good idea).
    Then wireless is not compatible.. you should download another driver for whatever wireless card the Sony uses.. intel most likely and they have a reputation as lousy. So download latest and a few prior to that as well.

  • Can't get wireless PCI card to work

    I bought a Sonnet wireless PCI card but we can't get it to work yet. Before I return it I wanted to check to make sure all the software was right.
    The AirPort utility is v4.2. The extensions are:
    Airport 3.4.7
    Airport2 4.0
    AirportFW 3.4.7
    AirportFWAP 3.4.7
    The system can see the card in the PCI slot (it didn't before upgrading the utility to 4.2, but the card doesn't detect any networks (and there are usually 3-4).
    I'm running 10.3.9 on a G4 MDD 2003.
    Thanks
    Tom

    Yes, it does have an external antenna.
    http://www.sonnettech.com/product/aria_pci.html

  • Can't get airport extreme to connect to xbox

    Hi! As you can tell from my post I am really new at this, i will try to explain as best I can:
    I have an Airport Extreme Base station(AEBS) connected by ethernet to a Westell 327W router, my airport is in bridge mode and has is successful networking three other laptops and a printer in the house. The problem is only with my xbox 360 The 360 reads the base station correctly, but will not accept the password (I have double-checked with ISP and the password is correct, X-box just won't accept it.) I have attempted to program with the Equivalent Network Password that I found (Airport>Base station >Equivlaent Network Password) to no avail. I was told by x-box tech that AEBS is just not compatible with 360 system. Please help - i don't want to re-do the whole system to get X-box live! Thanks. (I hope this description makes sense)

    My son has his xbox live working wifi with the aebs (n).
    However, he frequently complains about delays in general and delays with certain other players networked into the game. Occasionally, cable internet can slow down and xbox live regularly has its own issues. What is needed here is someone who can suggest alternative configurations using the aebs dhcp/nat settings. The airport utility help on this subject seems tentative and noncommittal in the vague suggestions provided. Miscrosoft xbox live is a reality that needs to be addressed. I am working on this issue when I can now. If I get any useful info, I will post it here. Is there an online gaming discussion group? That could help.

  • MBP can't find airport extreme but internet works

    I have a MBP with Lion.  I just purchased an airport extreme and connected an external harddrive with time machine linked to it.  Perodically my MBP, loses the Airport Extreme base station and cant find the Airport Extreme.  It cant find it in Airport Utility even after rescanning.  When this occures, time machine wont work because it cant find the drive/server.  I can manually locate the airport extreme by using the IP address though and I have a working internet connection.  But it's getting annoying because it seems to be at random that the base station just disapears.

    I bought an Airport Extreme yesterday and hooked it up today. Everything went great, but eventually all my wireless devices lost their connections. I've read several other forums where this has been observed as far back as 2009. Most attribute it to a firmware update, but that certainly isn't my case. My wireless devices include a Samsung TV, a Sony 'Google TV' internet box, and two Macs just to name a few of what I connected today. And they eventually lost their connection. Wired connections don't seem to be affected.
    It appears that Airport Extreme's wireless feature is going into a sleep mode that is hard for it to wake up from, or it's overheating (it gets very hot). And this has nothing to do with signal strength, range, or interference. It could be a combination of settings as a 2010 post stated that Apple told him to do a hard reset and ensure "Allow Setup over WAN..." and "Allow SNMP" are both unchecked.  Neither are checked on mine, so I guessing that might have been a lucky workaround back then. It's a pain to restart AE and re-enter the password on any device just because AE might have been idle for a period. After more than 2 years of this behavior, I'm surprised it continues to this day with no fix or clear explanation. Maybe there's a solution out there somewhere.....

  • Can't get Airport Extreme to recognize my eMac.

    I just invested in a MacBook and AirPort Extreme - I have the internet running on the MacBook but cannot get the older eMac (OS2.8) to recognize the wireless connection. I'm using a cable modem for internet connection. It looks like there is an AirPort Utility in the eMac but it doesn't recognize the MacBook as a base station. Would appreciate any help.

    In the system profiler of the eMac there are two AirPort entries: AirPort Admin Utility and AirPort Setup Assistant (both files are from 2003). Does this mean that I have a wireless card?
    No those are just applications used to configure one of Apple's base stations.
    In System Profiler, look under Network and then click on "AirPort Card". Is there any information in the right column? If not, the wireless card is not installed.
    If not, how can I reconnect the eMac to the cable service without shutting down the MacBook Base Station?
    When you say "MacBook Base Station" I assume that you mean AirPort Extreme base station (AEBS). You can connect the eMac to the AEBS via Ethernet without shutting anything down.

  • Can't get Airport Extreme to connect to Internet

    I have a D-Link 320T ethernet modem. This works fine connected straight into my Mac, but as soon as its connected to the Airport I loose my internet connection. Its seems to be something to do with my setup, but I'm clueless as to what.
    My airport seems to be transmitting something, as my Nintendo DS can pick up the Network name I have created, but it gives me this message "connected to access point, but unable to connect to the server", error code 52100.

    Hi Bidge,
    Welcome to the Apple.com user discussion boards!
    Do you have ADSL? Have you setup the Airport Extreme to establish the PPPoE session with your ISP?
    To configure this, please refer to this Apple article - http://docs.info.apple.com/article.html?artnum=166636

Maybe you are looking for

  • HDMI does not work, service tech still waiting for parts.

    Service tech can't get parts after 2 1/2 months to fix tv that i bought in Jan. 2012 it upsets me that this can't be resolved i spent 1400 dollars on a tv i can't use i would like to know who dropped the ball here?  some body please pick up the ball.

  • How to hide the view latest instance option for the reports in XIR3

    Created an access level and denied the rights "view document instances" and "view document instances that the user owns" in the access level. Applied this access level for a particular group on a particular folder. Login to Infoview and when view the

  • PC hard drive wiped out, how do I transfer to new one?

    Our home PC (running Windows XP) had to have it's hard drive replaced, therefore I lost everything I had on itunes (I know, I know, I should have had it all backed up!). I spoke to a great guy on the helpline, who told me how to at least get all my p

  • Where do I find my Acrobat Serial Number? It's nowhere on the box.

    Hi there, I've been trying to licence my Acrobat Pro software, but I can't find the serial number on the box. I only have the barcode Can anyone tell me where I could find this, because I have about 5 days left on my trial version. Prema

  • Programatically pushing toolbar button in web browser

    Hi all, I've got a tool going via a c++ plugin. Pushing the tool button and using it works well in Acrobat, including inside an internet explorer browser window acrobat plugin. What i'm trying to do now is activate the tool programatically by sending