Can't get an Open NAT on my Jetpack

I have a Jetpack 5510L. I use it to play on my Xbox 360 and whenever I get on Call of Duty or Halo, it says that I have a moderate NAT. I can still get into some games but not alot. Is there a way to get it so my NAT is open?

No.
Your VZW Jetpack is sitting behind a corporate NAT firewall. No amount of configuration will allow you to open up your connection so that it will appear more like a normal public internet connection. This is a well documented limitation of the Jetpack devices.
Workarounds are as follows:
1. Find a way to setup a VPN so that you appear to be connecting from a normal public internet connection. This is particularly difficult for an Xbox scenario. You would need a VPN router and then cascade it into the Jetpack so that anything connected to the router is auto tunneled to the VPN server.
2. Purchase a static IP address from VZW for around $500.00.
3. Terminate your Jetpack and get VZW Home Fusion. HF comes with a non NAT connection.
3. Terminate and find an alternative service provider who can offer you a static and public IP address.
Xbox needs public IP Addresses for you to host games. It should not be necessary to join other Xbox games but it all depends on how that game is hosted. At the moment Xbox and VZW jetpacks are not a good combination.

Similar Messages

NAT settings Moderate can't get to Open

I have spent 6 hours trying every tip I could find in past Apple Support Communities, Google searches, etc and while I can connect to XBOX live it is still giving me a NAT moderate setting warning.
My modem is an Actiontec GT701-WG and my router is Time Capsule Firmware 7.6. Ethernet connection of TC to iMac. WiFi to Xbox from TC.
I think my issue is double NAT by the modem and the TC.
If I turn off NAT in the Actiontec modem, it requires a static IP address provided by my ISP, which I do not have.
I do not use the wireless component of the modem because the Time Capsule gives a better connection. So my thought is I don't want to bridge through the Time Capsule and downgrade my WiFi connection just to get an Open NAT connection on the Xbox Live Connection Test.
I have enabled UPnP on the modem.
I have enabled port mapping on the Time Capsule for the UPD/TCP ports 3074, 88, and 80 used by Xbox.
I have manually assigned a static IP address in the XBOX network configuration, and matched it to the port mapping on the TC.
I have set the DHCP address reservation in the Time Capsule for the Xbox IP address.
I have unplugged in the order recommended and restarted.
When I play a game online via Xbox Live, I can sometimes hear other players and sometimes I can not, sometimes I hear part of what they are saying.
Am I overlapping strategies and making this harder than it is?
Should I just be happy I can connect and play an Xbox Live game with Moderate NAT settings or am I missing something to create the Open NAT?

LazrDDS wrote:
I have spent 6 hours trying every tip I could find in past Apple Support Communities, Google searches, etc and while I can connect to XBOX live it is still giving me a NAT moderate setting warning.
My modem is an Actiontec GT701-WG and my router is Time Capsule Firmware 7.6. Ethernet connection of TC to iMac. WiFi to Xbox from TC.
I think my issue is double NAT by the modem and the TC.
There are at least 2 ways to fix that.. bridge the modem or bridge the TC.
If I turn off NAT in the Actiontec modem, it requires a static IP address provided by my ISP, which I do not have.
Not sure.. it depends on if your ISP supports pppoe.. if so you can use pppoe client in the TC without having a static IP.
I do not use the wireless component of the modem because the Time Capsule gives a better connection. So my thought is I don't want to bridge through the Time Capsule and downgrade my WiFi connection just to get an Open NAT connection on the Xbox Live Connection Test.
I have enabled UPnP on the modem.
I have enabled port mapping on the Time Capsule for the UPD/TCP ports 3074, 88, and 80 used by Xbox.
I have manually assigned a static IP address in the XBOX network configuration, and matched it to the port mapping on the TC.
I have set the DHCP address reservation in the Time Capsule for the Xbox IP address.
I have unplugged in the order recommended and restarted.
When I play a game online via Xbox Live, I can sometimes hear other players and sometimes I can not, sometimes I hear part of what they are saying.
Am I overlapping strategies and making this harder than it is?
Should I just be happy I can connect and play an Xbox Live game with Moderate NAT settings or am I missing something to create the Open NAT?
Ok, this is the way I would do it..
Pick one device as the router.. the easiest is the modem.. as it uses upnp.. Apple doesn't use upnp which is a pain.
So you need to bridge the TC.. this is easy. Go to airport utility and open the TC.. go to internet tab and down the bottom, connection sharing.. off (bridged).. update the settings.
The TC will now become a wireless and switch.. plus hdd. You can use it exactly as before .. you may need to turn off wireless if the modem also includes wireless or set channels manually.
The TC will create a wireless link between the modem router and the xbox.. but it is purely lan side.. no routing. Any issues are then to do with the modem router and you may need to troubleshoot there as well, or it might work fine.

How can I get the "Open" and "Save As" dialog boxes to open at larger than their default size?

How can I get the "Open" and "Save As" dialog boxes to open at larger than their default size? I would like them to open at the size they were previously resized like they used to in previous operating systems. They currently open at a very small size and the first colum is only a few letters wide necessitating a resize practically every time one wants to use it. Any help would be appreciated.

hi Prasanth,
select werks matnr from ZVSCHDRUN into table it_plant.
sort it_plant by matnr werks.
select
        vbeln
        posnr
        matnr
        werks
        erdat
        kbmeng
        vrkme
        from vbap
        into table it_vbap
        for all entries in it_plant
        where matnr = it_plant-matnr and
              werks = it_plant-werks.
and again i have to write one more select query for vbup.
am i right?

How to get a open NAT type with a linksys E2000 on PS#

I called customer service and they were completely clueless, told me I had to pay for the Tech support to fix it. I have a Linksys E2000 and I cannot get a open nat for my PS3, tried the DMZ, and XBox settings but that obviously didnt work. So anybody have any ideas before I return this $100 router???
Solved!
Go to Solution.

I've been having the same problems but on my Xbox. I'm going to try this:
On router:
1 - Status tab
   Get DNS 1 & 2
On Xbox:
2 - Static IP on Xbox
   IP: 192.168.1.xxx
   Mask: 255.255.255.0
   GW: 192.168.1.1
3 - DNS Addresses on Xbox
On router:
4 - Forward ports
   TCP 80
   UDP 88
   Both 53, 3074
5 - Security tab
   uncheck Block Anonymous Internet Requests
   disable uPnP?
6 - Reset devices
I'll let you know how it goes.

Just upgraded to Maverick and can't get my opening page to stay on GOOGLE. it keeps opening in SITES and then I have to click on GOOGLE.

I just upgraded to Mavericks and can't get my opening page to stay on GOOGLE. IT keeps opening in SITES and then I have to click on GOOGLE to begin searching. I would rather not hav to go through 2 steps to start everytime. I entered google's address in preferences but it ignores my preference.

You don't say which browser you are using so I will assume it's Safari. If so then open Safari - Preferences - General tab and look for where you set the home page, just set it to www.Google.com
If this fails for some reason then open Safari and reset it (look in the Safari menu) and choose all options for the reset. The re-try setting the preference. Post back with your results.

WRT54G how to get a open NAT?

I have a WRT54G and it is not even possible to get a true open NAT with it for the xbox 360. I have tried port forwarding, DMZ, UPnP and just about everything else but nothign works. I can't seem to find a match of Call of Duty 4 online at all with the modem hooked up but as soon as i run it straight from the modem i find a match in like 3 seconds. Right now my 360 says open NAt but is not because i can't talk to friends or find matches so why does it says its open if it's not? Is there anyway or is this modem just garbage? I have seen alot of post regarding this problem with the WRT54G so i'm starting to this its a crap router. My router is version 6 by the way. Any help would be great thanks.

Ive opened up so many diffrent ports for it that i can't remember them all and yes i ahve set my MTU to 1365. So any other help maybe if anybody has this router and can get it to work with xbox live or mainly Call of duty 4. Maybe somebody could tell me why it says i have a open NAT when i obviously don't?

Getting an Open Nat on XBOX One?

Hi all, first post here.
I'm trying to configure my Xbox One so that I have an open nat type as opposed to the moderate one I have now but have abosuletly no idea on how to go about this. I've followed a few guides, but not made any progress. In terms of hardware, i'm running with a BT HH5 Type A on Infinity Option 2. I know for a fact I'm not on Carrier Grade Nat.
So, any ideas? I'm a bit lost really...

The Home Hub 5 has poor UPnP support. Because of this it is not fully compatible with the xbox one.
There are work-arounds you can try
To tell you how to get round the problem I need to know a couple of things
Do you own more than one Xbox One?
Do you also own an xbox 360?
Do you play Call of Duty Ghosts on the xbox one?
There is a workaround to open the NAT but this wont work for call of duty ghosts.
Go to the Network settings in the xbox settings app then run a multiplayer test. When test is finished press and hold both the triggers and the bumper buttons at the same time to go to detailed stats screen.
When on this screen press A then press A again. Hopefully your NAT should now be open. You sometimes have to do this two or three times though to get the NAT open.
Because of the home hub 5's poor UPnP support though there is no way to open the NAT in cod ghosts using UPnP. You need to forward port 3075 to open the NAT in Ghosts.
This is all a total pain and I keep hoping BT will update the firmware with a fix but i not holding my my breath.
It should be said though that NAT doesn't matter for games that use dedicated servers. So for games like Forza or Titanfall you don't need to worry about NAT. It's only games that use p2p that need the NAT open like COD or assassins creed black flag.

In contacts I just have a list view but can't get my open book view

In contacts I can only get a list view, I don't know how to get back to my open book view.

Transfer your iTunes folder (which contains your entire iTunes library) from your old PC to your new PC. On Windows, your iTunes folder is in the “My Music” folder. Place it in the same location on your new PC and quit iTunes before making the transfer. You will also need to authorize your new computer with iTunes with your iTunes account.
Syncing contact information and calendar events is done by iTunes with the supported application on your computer, but is not stored by iTunes.
You can sync contact info and calendar events with Outlook 2003 or 2007, or contact info with the Address Book used by Outlook Express with XP, or with the Address Book used by Windows Mail with Vista - the name change for Outlook Express with Vista.
Before syncing contact info with the supported application on your new computer, enter one contact in the address book on your computer. Make one up if needed. If you are syncing with Outlook 2003 or 2007, do the same with a calendar event.
This will provide a merge prompt when syncing this data, which you want to select.
Any photos transferred from your old computer to your iPhone need to be transferred from your old computer to your new computer.

Can't Get into Open Firmware

Hi there,
I've got a G3 All-in-One and I can't seem to get into Open firmware properly. I've got the right combination (Option-Apple-O-F) but the screen just goes black. I've tried this on two different units and they do the same thing. Am I missing something?
Thanks in advance...

every once in a wile mine does the same thing. but it really is at open firmware its just the screen is so dark you can barly see anything even in a room at night with all the lights out. try doing it in a very dark room and look real close to the screen.try resetting pram first to see if that helps and then try to go into open firmware. I have 2 beige G3 AIO's both do this try to hold the key combo as soon as you start to hear the start chime, then if this dont work try to hold them just after the start chime, and try to hold them at diffrent length's of time first start by trying to jusk keeping the key combo held down, then try realeasing then just after start chime, one of these combo holds should work. but make shure you are in a room that will be dark with the light's turned out cause very faintly you should see the open firmware prompt at the very top left of the screen.
good luck

Can't get file open thumbnail previews inside Photoshop CC?

Hi all,
When in Photoshop CC I then go to file / open, my machine won't display preview thumnails for each of my image files (.jpg, .gif, .png, .psd etc) and all I see is the blue Photoshop icon for each of these files, I have also tried changing the view options on the folder and change to medium, large and extra large thumnbails but again they all just display the Photoshop CC blue icon.
When I run Photoshop CS5 on this exact same machine it shows them!
Is there a setting I need to change in Photoshop CC to get this to work, or is Adobe trying to get us to use bridge or?
I am running Windows 7.
Any help would be great

I can recommend trying out the FPV codec pack. http://www.fastpictureviewer.com/codecs/
It's a trial,but I get thumbs inside Photoshop CC under Windows 7 and for a $15 license it's a deal.
There are programming reasons as to why thumbnails won't register in newer versions of Photoshop,but I'll have to let an Adobe programmer explain that part.
Gene

Can not get pass opening screen, help please!!

First off, when I tried to turn of my emac earlier this evening it took a few tries. Then when I went to turn it back on, it got to the opening white screen, with the grey apple in the middle but would not go any further. I tried a few more times, with the same results, white screen, grey apple, no farther.
Any help will be much appreciated, I thank you in advance!!

You can also try to Start Up in Safe Mode, with one important warning: once it gets to the gray screen / Apple logo stage, walk away and leave it be for at least a half hour! When a Mac shuts down improperly (power failure, errors on shutdown, multiple force restarts before completing startup), on next start it will attempt to run a faceless variant of the Repair Disk utility in the background. Depending on the size of the hard drive, the amount stored on it, the processor speed, and the amount if any of damage detected, this can take anywhere from 5 minutes to over 30 minutes. If the process is interrupted and the Mac restarted or shut down, then it tries again from the beginning on the next start. This can obviously put you in a vicious loop if you're not aware of what it's trying to do.
Since the Safe Mode disc repair is faceless, you don't get any immediate feedback as to any errors being turned up. It's better to follow cosmichobo's advice and use the OS X Install disc to run Disk Utility from the Installer menu; that will let you see what's going on. Note that if any errors are reported repaired by Disk Utility/Repair Disk, you should immediately run it again --- it's possible for one disc error to mask others.
Another option would be to boot the Mac into single user mode and use the Unix file system check utility fsck (if you're not adverse to using the Unix command line prompt). Refer to Using Disk Utility and fsck for detailed instructions.

My ipod is disabled and i can not get it open to put a password in.

Whatdo i do when I can't open my ipod because it is disabled? It wont let me even put in a password. I tryed connecting to itunes and it says my ipod is disabled and i need to disable it. What can i do?

Hello Nicolemarie8888
Put your iPod classic into Disk Mode and plugging it into your computer and restore it in iTunes. The articles below will assist you to get past being stuck with the passcode on your iPod classic.
Putting iPod into Disk Mode
http://support.apple.com/kb/ht1363
Restoring iPod to factory settings
http://support.apple.com/kb/ht1339
Regards,
-Norm G

Magic trackpad is stuck shut and there's corrosion. How can I get it opened, or am I out of luck?

I went to change the batteries and noticed corrosion. I can't even get the batteries out. I bought it about a year ago. Will any of this be covered by Apple, and is there a good work-around to get the battery compartment open, or am I out of luck?

IMHO you are out of luck. Even if it opened, the corrosion has probably damaged the device.
Barry

How can i get the open sale orders for given material no and plant

Hi,
I have to retrieve the open sale orders depending on the material number and plant.
For only open sale orders at header level and item level.
I want to use VBUK-GBSTK to find open sale order at header level and
                      VBUP-GBSTA at item level.
Can any one suggest me the best logic as performance is concerned?
Thanks,
Kumar.

hi Prasanth,
select werks matnr from ZVSCHDRUN into table it_plant.
sort it_plant by matnr werks.
select
        vbeln
        posnr
        matnr
        werks
        erdat
        kbmeng
        vrkme
        from vbap
        into table it_vbap
        for all entries in it_plant
        where matnr = it_plant-matnr and
              werks = it_plant-werks.
and again i have to write one more select query for vbup.
am i right?

I can't get firefox to open at all. I can't get it open to do anything on the firefox window such as open it in the safe mode.

A small screen tells me firefox was shutdown and windows was looking for a solution. I deleted Firefox and downloaded another Firefox program and installed it. The same thing happened. What do I do. Windows said it could be a DEP problem. I have no idea what that is. I can open Windows Explorer and use but I don't really like it. Help!!!

OK - undo the changes you made to DEP.
Open Firefox - take a screenshot of any message that appears and post back here

Can't get an Open NAT on my Jetpack

Similar Messages

Maybe you are looking for