Can't get any response out of Mobo

Technical information:
Motherboard: MSI PM8M-V
CPU: Intel 2.4ghz Socket 478
PSU: 400W (Tried 2)
Memory: PC2700 2 x 512mb
This is for a new system, and I can't seem to get any response out of my board.  I have two boards and am having the same problem with each.  When I press the power button nothing at all happens (no fans, etc).  If I unplug the JPW1 (CPU Power) connector then the fans will power up, etc. but nothing comes up on the screen.  If I plug the JPW1 back in and then try to boot then it doesn't show any response.
I've tried removing all components to make sure they aren't part of the problem, but I can't even get a basic BIOS screen to show up.  Any suggestions?

Updated PSU Info
ATX 2.03 (P4)
Orange +3.3v/25a
Red +5v/30a
Yellow +12v/16a
Purple +5vsb/2a
White -5v/.5a
Blue -12v/.8a
Black com/return
Green ps-on/remote
Grey PW-OK/PG
+3.3v&+5v=185W Max -5v&12V=9.6w max  All output is extended to 400W max
Also, I am in the USA and the PSU is set to 110v

Similar Messages

  • I can't get any response when I try to buy an onli...

    I can't get any response when I try to buy an online number....your response just sits and spins...please advise

    Dream all,
    My advice is don't do it. I wish I had come to the forums first and read about the problems before purchasing a number. When I bought callout credits I've had no problems at all. Now it looks like I'm out $18. I'm just thankful I didn't opt for the whole year.

  • On my Iphone 4, I can not get any response accept the apple logo after recharging for an entire day and trying to connect to iTunes. help?

    On my Iphone 4s, I can not get any response accept the apple logo after recharging for an entire day and trying to connect to iTunes. A few days before that the speaker suddenly stopped working during a call. I also reset everything by connecting to itunes but no luck then. help?

    Hey there xntricj,
    It sounds like you are putting a password for your Apple ID that works without issue on your iPad into your iPhone but get a message saying that the password is incorrect. I recommend the steps from the article named:
    iCloud: "Incorrect Apple ID or Password" alert when setting up iCloud after upgrading to iOS 7
    http://support.apple.com/kb/TS5207
    After completing iOS 7 setup, go to Settings > iCloud.
    Scroll down and tap Delete Account, then enter your previous Apple ID and password.
    If your Apple ID or password are not accepted, follow the steps in iOS 7: If you're asked for your previous Apple ID when signing out of iCloud.
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • I have a brand new Nano Ipod 7th Generation.  I can't get any sound out of earphones.  Yes, have pushed the cord all the way in.  Screen shows tunes are playing, but I can't hear anything.  Volume bar shows volume all the way up.  Now what?

    No sound out of earphones.  Yes, cord is all the way in the jack.  Screen shows tune is "playing", but I can't get any sound out.  Help

    If this is the case, I recommend to visit Apple store to request for replacement. Cheers!

  • I can't get any sound out of iTunes when i play a song.

    Ever since i upgraded iTunes i can't get any sound out of it. The player shows the bar moving through the song but nothing is heard.

    Go to the link below.Enter your Product Number as listed on Service Tag attached to bottom of notebook (may be under battery). You can also get the Product Number by pressing Fn + Esc key. After entering PN, click Next ,then choose Software & Drivers.On the next page use the dropdown to select your OS (probably Windows 7 64bit). A list will populate with drivers. Download & install the latest Audio driver.
    http://h10025.www1.hp.com/ewfrf/wc/siteHome?cc=us&​lc=en
    ```````````````````````````````````````
    If still no sound,try a hard reset, works sometimes.Disconnect all external devices first.
    1-remove power cord and battery
    2-press power button for 30 seconds
    3-reinstall only power cord for first startup.
    4-power on
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Can't get any response from HttpsURLConnection

    sorry, i've reformat the code here again
    Deal frens,
    Currently i'm doing a code to get a response from https link in my servlet. I don't know where the lack of my coding, but i don't get any response from the server when i execute my code. here is my code
    import java.io.*;
    import java.net.*;
    import javax.servlet.*;
    import javax.servlet.http.*;
    import javax.net.ssl.*;
    public class Servlet1 extends HttpServlet {
      private static final String CONTENT_TYPE = "text/html";
      //Initialize global variables
      public void init() throws ServletException {
      //Process the HTTP Get request
      public void doGet(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException {
        response.setContentType(CONTENT_TYPE);
        PrintWriter out = response.getWriter();
        String authentURL = "https://server1.tst.cvs/servlet/RequestHandler?login=admin&pwd=admin&method=viewUser&username=00032a0183db";
        out.println("<html>");
        out.println("<head><title>Servlet1</title></head>");
        URL url = new URL(authentURL);
        HttpsURLConnection URLconn = (HttpsURLConnection) url.openConnection();
       // HttpsURLConnection conn = null;
        URLconn.setDoInput(true);
        URLconn.setDoOutput(true);
        URLconn.setRequestMethod("GET");
        URLconn.setUseCaches(false);
        OutputStream authOut = URLconn.getOutputStream();
        BufferedReader reader = new BufferedReader(new InputStreamReader(URLconn.getInputStream()));
        out.println("<body bgcolor=\"#ffffff\">");
        out.println("<p>The servlet has received a GET. This is the reply.</p>");
        out.println("output"+authOut);
        out.println("output2"+URLconn.getContent().toString());
        out.println("output3"+reader);
        out.println("</body></html>");
      //Clean up resources
      public void destroy() {
    } the result suppose i get when i execute the script is..
    userdata=234&uname=00032a0183db&concurrentlogins=1
    i don't have any problem when i paste the link
    https://server1.tst.cvs/servlet/RequestHandler?login=admin&pwd=admin&method=viewUser&username=00032a0183db
    and i able to get the response
    userdata=234&uname=00032a0183db&concurrentlogins=1
    please..please help..what is wrong with my code

    YOU DON'T READ ANYTHING IN YOUR CURRENT CODE !!!
    If you use a BufferedReader, then read the input stream via readLine() method.
    Default implementation of getContent() method is not generally usable for getting your desired "content". Experiment that.

  • WIRE DOWN: Can't get any response to a wire down.....

    It is virtually impossible to report a Verizon wire/cable down.  It took me nearly an hour to find a number.  Verizon sites have nothing.  I finally got a number from Ask.com.
    I reported the wire down; explaining that I had called the localelectric utility.  They were there in 30 minutes - but they said they can't repair the line, as it is a Verizon cable that is down.  Apparently, since the service is not OUT - they don't seem to care.
    Wire is hanging from pole line...about 6 ft. off the ground.  I reported - Ticket number: {edited for privacy}; but nobody came.
    Getting a response from the Maryland Public Service Commission is almost as bad.  What gives??

    Hi PoppyBaze,
    Your issue has been escalated to a Verizon agent. Before the agent can begin assisting you, they will need to collect further information from you. Please go to your profile page for the forum and look at the top of the middle column where you will find an area titled "My Support Cases". You can reach your profile page by clicking on your name beside your post, or at the top left of this page underneath the title of the board.
    Under "My Support Cases" you will find a link to the private board where you and the agent may exchange information. This should be checked on a frequent basis, as the agent may be waiting for information from you before they can proceed with any actions. Please keep all correspondence regarding your issue in the private support portal.

  • Can't get any response from the Tuner - is it broken?

    I'm happily chugging away through my new David Nahmani tutorials and I've discovered that I can get no response from the Tuner. The controls in the window appear to be working, but no line appears in the meter and flat lines appear in the center for pitch and octave. The channel strip indicates normal sound input and variation. I don't have any trouble recording (so far anyway). Is there anything I'm not aware of that could cause this?

    Thanks for the reply, Rob. I'm just trying to tune a wind instrument through the built-in mic on my MacBook Pro, but I discovered the answer not too long after submitting the question. As I said, I'm trying to work through the Nahmani Logic Pro and Logic Express 8 book. I've been trying to be very meticulous about the installation and the setup for the tutorials, but I guess I inadvertently made settings changes that interfered with the Tuner, because choosing Logic Express > Preferences > Initialize All Except Key Commands allowed the Tuner to work the way I expected. I assumed the problem must have been bus related after I saw the Tuner respond to internal playback after modifying some bus settings, so I executed that command and all was well (uh, I should probably change that to "most was well", but at least the Tuner is working now). Thanks again.

  • How come I can't get any sound out of my speakers

    I  have a mid 2011 iMac...can't get sound to come out of the speakers... It was working earlier today... I checked to make sure everything was connected and not muted... Thank you in advance for any help out there...
    Shane

    Go step by step and test.
    1. System Preference > Sound > Output > Internal Speakers
        Highlight  Internal Speakers / Headphones
        Make sure that Mute is not enabled.
    2. If you see red light in the headphone port, plug the headphone
        in and out of the port 5 or 6 times to flip the microswitch inside.
        Sound output may be stuck in the digital mode.
        Try this even if you don’t see the red light.
    3. Reset PRAM.  http://support.apple.com/kb/PH14222
    4. Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the appropriate method.
    5. Applications > Utilities > Audio MIDI Setup
        Audio Devices window
        Side Bar
        Click the Built-in Output.
         Make sure that no box is checked under “Mute”.
    6. System Preferences > Sound> Sound Effects
        Play sound effects through:
        Select "Internal speakers" and then back to "Selected sound output device".
    7.Launch iTunes and play a song through headphone and adjust the volume
       in  the Mini player.

  • I can't get any sound out of the speakers

    Sound coming out of my speakers

    Go to the link below.Enter your Product Number as listed on Service Tag attached to bottom of notebook (may be under battery). You can also get the Product Number by pressing Fn + Esc key. After entering PN, click Next ,then choose Software & Drivers.On the next page use the dropdown to select your OS (probably Windows 7 64bit). A list will populate with drivers. Download & install the latest Audio driver.
    http://h10025.www1.hp.com/ewfrf/wc/siteHome?cc=us&​lc=en
    ```````````````````````````````````````
    If still no sound,try a hard reset, works sometimes.Disconnect all external devices first.
    1-remove power cord and battery
    2-press power button for 30 seconds
    3-reinstall only power cord for first startup.
    4-power on
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Hey i have a ipod touch and i can t get any sound out of my head phones. The lil bit i can get is scratchy and very very low??

    I have a ipod touch and i can only get a very lil bit of sound and its scrachy souding out of my head phones... sounds good if you dont use head phones??? Can anybody help??

    Your MacBook Pro doesn't have HDMI output... it's DVI. For sound, you will need to use the headphone out/optical digital audio out port to the TV/stereo. As far as video goes, I'm confused as to what cable you're using but at one point you're converting DVI to HDMI.

  • GmaiI crashes the iPad; everything locks up and I can't get any response.

    I foolishly opened many Gmail messages on my iPad while looking for an old message.  Now I can only open one or two messages before the screen locks and there is no response to any command.  I have to go back Home and open mail again.
    If I Delete my gmail account from the iPad in Settings, will that only delete it on the iPad.  I would try deleting the account and then adding it back.  Everything worked well with Gmail until I opened too many messages and I think overloaded it.
    Any suggestions?

    Reset your iPad: Hold down the home and sleep buttons, wait for the Apple logo, let go of the buttons.

  • I can't get any sound out of my iMac unless I am wearing headphones.  Is there a way to fix this?

    When I turned on my computer this morning I noticed that I didn't hear the chime, but realized that my son had left his earphones plugged in.  When I unplugged them, the computer still didn't have any sound.  When I plugged the earphones back in I could hear sound but only in my headphones.    We stream Netflix/Hulu videos so we are in need of help.  Has anyone else had this problem?  If so, is there a solution?

    Sounds like either the internal speaker volume is muted or the micro switch inside the headphone jack is stuck and the computer thinks something is still plugged in.
    1. Check the sound preferences and see if you can select and/or unmute the internal speakers?
    2. If not, try plugging in gently jiggling and then unplugging the headphones to see if you can unstick the micro switch?
    3. If not, contact your local AASP and make a service appointment.

  • Apart from the phone function, I can't get any sound out of my iPhone, i.e. music, youtube movies etc. is this a failing phone or a settings problem. I and others all failed to find a relevant setting.

    What photo?????????.

    It's atrocious... And they don't give a **** at all. I'm serious considering going with a different carrier after nine years. These guys will tell you anything just to lock you in your contract for another two years. They never had the number of units upfront to be selling us all in a pre order, that's already been reported. And they continue to jostle dates around and blame it all on Apples supply. The ironic part of the excuse is that they cannot take stock of what they have real time and then make those phones available on time and begin the back order process per the demand in real time either. As if to say " Appke will be getting is more they promised", when they should be saying " we're sold out and were not sure when our supplier is going to send the next shipment to fulfill orders" but you hear mon of that from these scumbags. They just want you to take a month late "pre order" and then say that it's all apples fault. Suggestion Verizon : DONT ******* SELL PHONES YOU DONT PHYSICALLY HAVE TO SELL IN A PRE ORDER

  • NO SOUND! I can't get any sound out of logic express....

    Very recently, sound stopped coming out of my Logic Express.
    There is a level (on the master) going out, and the master volume of the program is up, but nothing is coming through the speakers!
    All other sounds are coming out (itunes etc), just not logic. Has previously been working fine!
    I must have clicked something by accident, any suggestions please?!?
    Alex

    The first time I synced with the ipad I did go through "restore" from iTunes. The other options on the screen were "restore from iCloud" and "new ipad".
    How do I do a restore now? With the ipad attached? Everytime I connect and disconnect the ipad to the cable, even with reboot, it takes me back to the same grey iPad configuration screen. Do I need to do a hard reset?

Maybe you are looking for