Can't get DVD burner or Isight camera to work via FW

I can't get a DVD burner (FW) or an Isight camera to work. The DVD doesn't mont and the Isight camera just turns on then back off.......I did all the disc maintenance and reset the PRAM. At one time these devices did works. Sometimes the FW board shows up in the System Profiler and sometime it doesn't. Could it be a faulty FW board? Firmware?

A new PCI card and $39 fixed it. I got the firewire 400 since my DVD burner and iSight camera run on 400. The 800 would have been nice. And it was on sale as a discontinued item, $22 ($99). But there is a catch, 400 and 800 cables aren't the same. DAH!!! New cables would have cost around $68. Yes, I do have cable supplier here in town were I could have bought the same cables at pennies on the dollar. Another DAH!!! I didn't think of it till after I put the card in. All so my cable supplier is on the other side of town. I'm tried and lazy right now.
Here ends another happy story, and I thank you all.......

Similar Messages

How to I get the built-in iSight camera to work?

My built-in iSight camera is working but the "capture" button is greyed out and I can't record.

Hi there,
You may want to take a look at some for the troubleshooting steps found in the article below, specifically the section titled "Built-in iSight cameras"
How to Troubleshoot iSight
http://support.apple.com/kb/ht2090
Hope that helps,
Griff W.

Can't get Apple Laptop built in camera to work with Adobe Flash Player

Is there any way to get this to work? I'm trying to build an application that will work with both PC and Mac web cams and this won't work. Are there any other choices out there or anyone with experience on this? Thanks

Hello Brickwell
Perhaps I misunderstand what you want, but iSight works with Flash Player web content.
Have you configured your browser's Flash Player settings? If not, try the suggestion from this post:
http://discussions.apple.com/thread.jspa?messageID=4761707&#4761707
EZ Jim
PowerBook 1.67 GHz w/Mac OS X (10.4.11) G5 DP 1.8 w/Mac OS X (10.5.1) External iSight

In camera on iPad with the iso7 I can not get the video aspect of camera to work., any ideas?

In the camera app. I can take pics. But when I touch the video ,to change to taking a video it does not let me. All I can do is take pics. Any ideas of what I can do to make this work.

It took me a whole to work it out as well, it's not at all obvious. you don't press "video", like any normal person would assume. You have to slide those words up and down. Some of the design choices they have made in ios7 are just plain weird. My favourite is in Game Center... They have hidden the "play game" option behind three little dots.

Can't get my Linksys WVC54G IP Camera to work with AEBSn

I have even experimented with turning off WEP... doesn't work. I turned on MAC Address filtering and added the IP camera's MAC address to the router... doesn't work. The IP camera has a hard-coded IP address that is on my home network segment, comfortably in the range of IP addresses allowed with no other conflicts. Has anyone else gotten this product to work?

Hi JHeck16,
Welcome to the Support Communities!
You may have already tried some of these steps, but I would propose trying them again in the order presented:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Cheers,
Judy

How can I use the built-in Isight camera with an external camera (usb/firewire) at the same time?

How can I use the built-in Isight camera and an external video camera at the same time?
I'm wanting to stream over Oovoo/Skype/etc. using 2 cameras.
Thanks

Simple question with a not so simple answer.
(a) If you mean that you want to run multiple apps simultaneously using a different camera with each app, you may encounter computing power limitations. Digital video is processor intensive. The only way to know if your Mac can do this it to try it. If the video does not work together but each app works when it it the only app running, you are likely overloading your Mac's ability to process and/or move all the required data in your data bus. You can get a better indication of whether this is the case by watching your Activity Monitor utility while running the apps you want to use.
(b) If you mean that you want to have more than one compatible camera connected to your Mac simultaneously for ease of changing between video sources, some, but not necessarily all, apps you are using to operate your camera(s) allow you to select between your cameras.
How you select among connected cameras depends on which application you are using. Here is how camera selection works in a few examples:
(1) For iChat, you can choose which iSight you use in the "Camera:" choices bar in iChat > Preferences... > Audio/Video that appears when more than one compatible camera is connected. Although your camera choices will be different, the choices bar will look something similar to the Preferences settings shown here:
If you cannot see the "Camera" choices bar, your Mac is recognizing only one (or none) of your cameras. In that case, consider the suggestions fromhttp://support.apple.com/kb/HT2090 for iSight problems or refer to your other camera's documentation for help.
This particular choices bar solution applies ONLY to iChat. Most other applications also have settings that allow you to choose which camera to use. However, they do not all work the same way.
(2) For instance, iMovie HD's camera choice is NOT set via Preferences. When you have more than one compatible camera connected, iMovie6 HD uses a drop-down menu choice something like this (depending on which version of iMovie you use):
Note: Because I had no built-in iSight connected when I made this example, and because my external iSight was not connected, the drop-down menu showed only "Time Lapse." Because your Mac has a built-in iSight, your built-in iSight would show in the drop-down menu even when no other camera is connected. Connecting an additional Mac compatible webcam should allow you to choose either camera.
Other iMovie versions work slightly differently.
iMovie 9 (from iLife '11) uses a different camera choice button shown in this article:
http://docs.info.apple.com/article.html?path=iMovie/9.0/en/mov39f84285.html
iMovie 8 (from iLife '09) is slightly different as explained in this article:
http://docs.info.apple.com/article.html?path=iMovie/8.0/en/10172.html
In general, you can use your Mac's help for the application in use to find out how to select among more than one connected camera.
(3) Photo Booth in Snow Leopard 10.6.x and later uses the Photo Booth > Camera menu command to select which camera to use.
Note for readers with older Mac OS X: The previous version of Photo Booth that came with Tiger (10.4.x) is such a simple, basic app that it offers no menu selectable choice. Unless your built-in iSight is already occupied as the camera being used by some open application before you launch Photo Booth, Photo Booth will use ONLY your built-in iSight.
However, you can use the trick from ¶ 4 of http://docs.info.apple.com/article.html?artnum=302781 to let Photo Booth use an external camera.
(If you have an external Firewire camera connected, it may be used in preference to any USB webcam. If that is a problem for you, merely disconnect the problem Firewire device.)
(4) For FaceTime, launch the app and click the Video menu item.
If your Mac recognizes more than one connected compatible camera, a "Camera" section listing the cameras from which you can choose will appear there. Clicking on the desired camera name will let you select the one you want as shown in this image from my Mac Pro and LED Cinema Display:
If your Mac recognizes only one compatible camera, the "Camera" section will not appear in the Video menu, but FaceTime will automatically use the connected camera that is recognized by OS X.
(5) I do not use Skype oir Oovoo. For those or other apps, see Help for each app for info on how to select your desired camera.
Message was edited by: EZ Jim

How to get isight camera to work in windows live messenger

I'm on macbook using VMWare Fusion software, I have split HD into windows XP and Mac side. I'm trying to connect on windows side with my brother who has PC using the windows live messenger. I can't find out how to get my mac isight camera to work in windows live chat. Anyone know settings on win xp side for making mac built in camera work?
I tried mac side, but mac messenger doesn't have video capabilities!
Tks ahead for help!

I'm on macbook using VMWare Fusion software
Please post questions regarding Fusion on VMWare's own forums, as Apple discussions only provide support for Apple products:
http://communities.vmware.com/community/vmtn/desktop/fusion
I tried mac side, but mac messenger doesn't have video capabilities!''
Download and try aMSN: http://www.amsn-project.net/

Okay I use iPhoto 6 on an older mac and don't want to upgrade past 10.4.11. Can I upgrade iPhoto without the newer operating system? For the life of me I can't get iPhoto to recognize my camera reliably - although it does sometimes. Any advice, help?

Okay I use iPhoto 6 on an older mac and don't want to upgrade past 10.4.11. Can I upgrade iPhoto without the newer operating system? For the life of me I can't get iPhoto to recognize my camera reliably - although it does sometimes. Any advice, help?

The latest version of iPhoto which can operation with OS X 10.4.11 is iPhoto 7 which is part of iLife 08. You might be able to find a copy of iLIfe 08 on Amazon.com or Ebay.com.
iLife 08's full system requirements are:
Mac computer with an Intel, PowerPC G5, or PowerPC G4 processor
iMovie ’08 requires a Mac computer with an Intel processor, a Power Mac G5 (dual 2.0 GHz or faster), or an iMac G5 (1.9 GHz or faster)
iDVD ’08 requires 733MHz or faster processor
512 MB of RAM; 1 GB recommended; high-definition video requires at least 1 GB of RAM
3 GB of available disk space
DVD drive required for installation
From: http://support.apple.com/kb/HT1010
OT

How can I get all photos from the camera roll onto the photo stream so they will share between iphone and ipad?

How can I get all photos from the camera roll, and all new pictures taken, to get on the photostream so they can share between iphone and ipad?

When turning PhotoStream on with photos available in the Camera Roll, only photos captured by the iPhone or saved on the iPhone are placed in the PhotoStream.
For all photos that were in the Camera Roll prior to turning PhotoStream on, import the photos with your computer and add the photos to your PhotoStream on your computer.

I can't get dvds to play "There was an initialization error. A valid video device could not be found for playback. [-70017] Anybody know how to resolve this?

I can't get dvds to play and, instead, get "There was an initialization error. A valid video device could not be found for playback. [-70017]" I went in for a Genius appt Friday and it played for the tech...but now I'm back home (one and a half hours from the store) and I'm getting the error message again when I try to load a dvd. Any recommendations?

Hello, try this...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
Reboot... any change?

Bridge wont recognizw my Nikon d610. I am running windows 8 and photoshop cs6 with 8.6 camera raw plug in. How can I get bridge to recognize my camera? Thanks to anyone who can help!!

Bridge wont recognizw my Nikon d610. I am running windows 8 and photoshop cs6 with 8.6 camera raw plug in. How can I get bridge to recognize my camera? Thanks!!

That camera model has been supported since ACR 8.3 and it is most certainly supported by ACR 8.6 and ACR 8.7 (beta).
Either you have damaged, corrupt image files, or a faulty Photoshop and/or ACR installation.
If there are no privacy issues, you can post one of your files to the FTP service of your choice (such as Dropbox or yousendit.com), post the link to it, and someone here can take a look at it for you.

I have aperture 3.2.4 on my laptop and have the serial number, but just bought a new MAC and I can't get the Ver 3.0 link to work. Anyone know how to move it from my laptop to our new mac?

I have aperture 3.2.4 on my laptop and have the serial number, but just bought a new MAC and I can't get the Ver 3.0 link to work. Anyone know how to move it from my laptop to our new mac?

I am talking about the Ver 3 download link that came with the purchase email.
That link is no longer available. Use "Migration Assistant" to copy your Applications from your old mac to the new Mac, then immediately run software update. Aperture Version 3.2 will not run on your new mac with Mavericks, you will have to Upgrade to version 3.4.5 at least - you can download this update from the Support page: Aperture 3.4.5
Then launch Aperture and enter your registration key and try now too update from version 3.4.5 to 3.5 from the AppStore. The AppStore will change your Aperture registration to an AppStore version, so you will able to reinstall by downloading from the AppSTore in future.
If you want transfer only Aperture and no other applications, do it manually: You will have to copy not only the application but folders from the libraries as well:
/Applications/Aperture.app
/Library/Application Support/Aperture/
~/Library/Application Support/Aperture/
Leonie

Isight camera not working after the last update

After reboot of the last OS update
Isight camera not working...
i've tried photobooth, ichat, skype and it doesn't show up anywhere. in fact, when i go to system profiler, it doesn't show isight under USB connections at all.
just to give you a recap of what i've tried so far:
* restarting (obviously)
* resetting PRAM/SMC (by booting it the way it was specified in the isight troubleshooting thing)
* just shutting down my computer and taking the battery out for several hours
any Help pls
because i mast to use it as soon as possible in a conference

*A few suggestions.........*
Try running repair permissions from your HD and afterwards run +repair disk+ from your software install DVD.
my isight camera is not working-not recognized with photo booth or ichat
To fix your iSight, shut down computer. Reboot in safe mode (press power button and then hold shift key down). After computer boots, restart again. Hopefully, your iSight will start working again.

(Slow Network): iSight camera not working in iChat since Leopard upgrade

I have a different type of iChat video issue. My Power Mac G4, 867 MHz, 1 GB DRAM is a supported Mac for the Leopard upgrade. I've successfully installed OS 10.5.
Also my Power Mac meets the iChat Conferencing Requirements for 1-on-1 Video Chat per the OS 10.5 system requirements and the application note here:
http://docs.info.apple.com/article.html?artnum=301050
My iSight camera is connected via Firewire to an Apple Cinema Display, which feeds back to the Power Mac G4.
1) When I boot from my 10.3.9 Carbon Copy Cloner backup my iSight works in iChat (at least locally to see myself) without any issue. Green light comes on and shows me locally on video and audio sound bars. Before the OS upgrade the iSight worked fine for live video conferences with iChat 2.1.3 under Mac OS 10.3.9
2) Running OS 10.5 when I go to iChat 4.0's preferences video pane the following message is waiting "This computer does not support video conferencing."
3) With Leopard iChat 4.0 the Connector Doctor under "capabilities" says "(Slow Network)" for 1-on-1 Video Chat and won't even show video locally or turn on the iSight's green light.

Fixed!
My Power Mac Quicksilver G4, 867 MHz. problem with (Slow Network) in the iChat Connection Doctor, no video preview or video iChat since upgrading to OS 10.5 Leopard and iChat 4.0 has been solved with the following posted towards the end of the thread below. I can finally see my video preview with iChat 4.0 and have also video chatted successfully with one other user.
Topic : Macbook - iChat says "This computer does not support video conferencing"
http://discussions.apple.com/thread.jspa?threadID=1197506
Fixed by Apple Article: http://docs.info.apple.com/article.html?artnum=307035
Products affected
Mac OS X 10.5 Leopard
iChat
PowerPC-based Mac with a 867MHz processor
Solution
Quit iChat.
Open Terminal (it's in the Utilities folder, in the Applications folder).
In Terminal type or paste this command on a single line:
defaults write com.apple.iChat newbwdup 300000
Press Return.
Quit Terminal.
Open iChat.

HT2090 External iSight camera quit working after upgrade.

My external iSight camera quite working after OS upgrade. It appears the Firewire port is dead. Camera doesn't turn on, no green light. The camera is not recognized by any software.

Restart your Mac and troubleshoot using http://support.apple.com/kb/HT2090 suggestions.
Be sure to test more than one Apple app in more than one user account. Do NOT use the "Guest" account for this test. If you do not have more than one user account for the testing, create a new one now. (A "Standard" account is all you need for testing.)
If your trouble persists, when you post back here tell us:
   (1) what version of OS X you use.
        (You can find this with your Mac's  > About This Mac menu command.)
   (2) Whether the "upgrade" you mean was an OS X upgrade, an iOS upgrade, or both,
   (3) whether your external iSight works with Apple apps like Photo Booth, iMovie, etc.
        If not, confirm that the symptoms are EXACTLY the same in every user account.
We will offer more specific suggestions based on the details you provide in your response.
Message was edited by: EZ Jim
Mac OSX 10.8.2

Can't get DVD burner or Isight camera to work via FW

Similar Messages

Maybe you are looking for