Can't get my Linksys E2500 to work

So I'm on Comcast and got tired of paying rental for a cable modem, so I went out and bought one. I bought the Netgear CM400. Brought it home and went through the deal of setting it up and everything worked just fine until I hooked it into my Linksys E2500 wireless router and nothing. I'm using a 2005 Dell Inspiron Laptop running Windows 7. My Linksys doesn't even show up in my list of networks anymore. Any ideas.

Make sure that you have an active internet connection to your Netgear modem. You’ll need to reset the router and manually reconfigure it with your Cable modem.

Similar Messages

Can't get brand new WRT610N to work with Billion 7404 VGOM

I already posted this on whirlpool, here are my posts:
Hey All,
Just bought a LinkSys WRT610n and I can't get the darned thing to work with my Billion 7404VGOM.
At the moment I just want to network my pc to the LinkSys, LinkSys connects to my 7404 which is connected to the internet.
I've tried using DHCP automatic connection with the WRT610N, but it just doesn't talk route any traffic to the 7404...and thus nothing to the internet.
All cables and plugged in correctly, I tried the auto setup also but just can't figure the thing out.
Any suggestions?
Cheers,
Ken
I can't ping my 7404 modem from my PC when connected through the WRT610N. I can ping the WRT610N successfully, but when trying to ping the 7404 the WRT returns "Destination Host Unreachable"
7404 is function fine if I just connect to it directly though.
I don't understand, even If I couldn't get DHCP info working or syncing between both devices, it should still be able to ping it.....?
Right, I just plugged in my netbook via network cable into the "Internet" port on my WRT610N. I try to ping the router using this (it doesn't get any DHCP settings from the router, so I just set it manually and use the WRT as default gateway ip)...I just get request timed out.
I should be able to do this right?....starting to think my WRT610n has a dodgy "Internet" port.
Any suggestions?

If you connect your notebook via network cable into the "Internet" port on the WRT610N and if you ping the router it will not reply...also your Notebook will get any DHCP setting with this connection...However what exactly is Billion 7404VGOM ? A modem i guess!! Who is your ISP ?

Want to take back because i can not get my ipod touch to work on this

I can not get my ipod touch to work on this Linksys WRT54g router at all.I called them and was on the phone for a hour and still can not get it to work.And it is not the ipod because if i go outside i can get on with someone router outside.Can someone Please Please Help Me with this i would like to be able to use my rounter.
Regards
Chippy

Chippy:
I'll assume you've read the iPod manual. The directions I have seem fairly straightforward - iPod connects to a wireless network when it discovers one. Or, if that option is turned off, you have to manually connect it.
When it comes to attaching to your router, you will need to know what kind of security the router is using, what the security password is and most important - the router's DHCP function must be activated so the iPod can acquire an IP address.
If the iPod truly can handle the connection, and you have the necessary information I mentioned, it should connect without a problem. But since you can't connect, you need to review the settings I mentioned.
It's possible there is some sort of issue with the router and the iPod. But it's my guess that the iPod is not acquiring an IP address because the router is not giving them out.
Check these things out and post what you find. If we can figure out the answer, your post will be helpful to others who may run into the same problem.

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone an i have internet and all other functions working on my computer

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone and i have internet and all other functions working on my computer

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, look under User Diagnostic Reports (not "Diagnostic and Usage Messages") for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents—the text, not a screenshot. I know the report is long. Please post all of it anyway.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

How can I get my web cam to work in Adobe Connect ?

This is actually an end user's question that I am having trouble answering to...
We use Adobe Connect to give online language classes, the end user is one of the students.
I cannot find the right Support answer to give him.
Problem:
My camera does not work when I connect to Adobe's rooms but camera works fine with other software.
Even though I suspected my old camera was working fine, yesterday I went ahead and bought a new camera.
I thought perhaps my webcam software may have been a problem, so I bought a different type camera with different software.
Even after removing all the old software, same result:
I surmised the problem might be caused by my firewall and security software, so once I tried changing the permissions for Adobe, and my Webcam, but that didn’t work.
Another time, I restarted my computer right before class and then turned off my firewall completely so there would be no interference but to no avail. I’m totally perplexed.
Isn’t there anyone else experiencing a similar problem?   Has anyone else found a solution?
I run Windows Vista with McAfee Internet Security Software. I always reboot the computer before class and open no other programs other than Google Chrome.
I now have a brand new Microsoft LifeCam Cinema Camera with LifeCam 3.5 Webcam Software.
I test my camera before going online. It always works fine.   Then I shut down the camera program and login into class.
When I “connect webcam” in the room, the light on my camera comes on (suggesting that it is ON), but only a black image is transmitted to the room.

Check to see if you have Google Voice installed. If so, remove it and see
if your problem vanishes. If not Google Voice, check to see if you have
any other communications software which interacts with your cam and
disable it. This was the problem I had with a similar problem on a Mac.
MosesJOI <[email protected]>
10/13/11 12:08 PM
Please respond to
[email protected]
To
jsb152 <[email protected]>
cc
Subject
How can I get my web cam to work in Adobe Connect ?
Re: How can I get my web cam to work in Adobe Connect ?
created by MosesJOI in General Discussion - View the full discussion
Thanks a lot Heyward for the swift reply !
I sent the advice out to the end user, but unfortunately this wasn't the
solution.
His reply is below :-
The default resolution of my new camera is already set at 640x360, but I
went ahead and tried several lower resolutions (e.g. 424x240; 320x240; and
160x120) but none worked in the room - camera still showed up as black
blank screen. Also, as far as I can tell, I don’t have the option of
adjusting the frame rate.
I started playing around with my Internet Security Settings to see if they
might be playing a role. So far, all to no avail.
Hmm...quite a tricky one - webcams always are - maybe if he can find a way
to adjust the frame rate (?).
He's going to fiddle about with the settings a bit more and see if
something does the trick.
If anyone has had a similar problem and found an ingenious solution,
please jot on a note on this thread.
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either
reply to this email or visit the message page: [
http://forums.adobe.com/message/3969561#3969561]
To unsubscribe from this thread, please visit the message page at [
http://forums.adobe.com/message/3969561#3969561]. In the Actions box on
the right, click the Stop Email Notifications link.
Start a new discussion in General Discussion by email or at Adobe Forums
For more information about maintaining your forum email notifications
please go to http://forums.adobe.com/message/2936746#2936746.

How can I get iCloud to accept my working Apple ID and password

My Apple ID and password works for iTunes and App Store. I'm trying to set up iCloud on my iPhone and iPad but i keep getting an error message that reads unsupported ID. Apple ID must be in the form of email address (@me.com). I don't have a MobileMe account. How can I get iCloud to accept my working Apple ID and password?

I've also reset my password to my Apple ID. I still get the Unsupported ID and password.

Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.

Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.

Hi deamayfield,
Thanks for visiting Apple Support Communities.
If your Music app is unresponsive, try restarting/resetting your iPhone:
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
Best,
Jeremy

I just got a new itouch and i can't get imessage or facetime to work on my home network

I just got a new itouch 4 and i can't get imessage and facetime to work on my home wifi network (Airport Express). I can't explain it. The itouch works fine otherwise uncluding the internet. Facetime and imessage work at the apple store so there must be something wrong with my home network. Please help if you can!
iPod touch, iOS 5.0.1

I changed the DNS to 8.8.8.8 as you suggested with no success, I even tried 8.8.8.8, 8.8.4.4 as suggested by others with no success either. When I try and activate iMessage or Facetime, I still get the same message "could not sign in, please check your network connection". The internet and Mail work perfectly fine on the iPod touch so the WiFi signal IS going through. I am at a loss, any other suggestions would be more than welcome. Thanks!

How can I get my excel spreadsheet to work in numbers

How can I get this budget sheet to work in numbers when it's from excel.

I couldn't get the picture of the whole thing it wouldn't load but you see where it say like 700.00 then below that it say 175.00 well that part works telling me what I need to know but when it get to where it says the 850 it stops working? it won't sum it out or something I'm not great with excel and this was sent to me by a first and it's our budget plan and I really need to be able to use it

How can I get my iPhone 5s to work in my 2015 outback

How can I get my iPhone 5s to work in my 2015 outback?

I Tried that and I can get calls out and in but no messaging.
AWindow opens and says this feature is not supported on this device
my iPhone 4 worked fine is it my iOS?

How can you get the apple tv to work in a hotel where to get on the wifi you have to still go to a website first and put in your room

How can you get the apple tv to work in a hotel where to get on the wifi you have to still go to a website first and put in your room?

Welcome to the Apple Community.
Unfortunately the Apple TV doesn't have a web browser so you can't do that.

How can I get an external microphone to work on an iphone?

How can I get an external microphone to work on an iphone?

Japib is correct.
WHAT happens? Exactly.
Also helpful would be to tell what event preceded this behavior - added App, update iOS, etc.
Quoted from  Apple's "How to write a good question"
To help other members answer your question, give as many details as you can.
Include your product name and specs such as processor speed, memory, and storage capacity. Please do not include your Serial Number, IMEI, MEID, or other personal information.
Provide the version numbers of your operating system and relevant applications, for example "iOS 6.0.3" or "iPhoto 9.1.2".
Describe the problem, and include any details about what seems to cause it.
List any troubleshooting steps you've already tried, or temporary fixes you've discovered.
ÇÇÇ

Hi, Im trying to install the CC installer on my new MacPro. When the installer loads it says there's a "Download Error" and can't get beyond that. Everything work fine on my old Mac. Any Ideas?

Im trying to install the CC installer on my new MacPro. When the installer loads it says there's a "Download Error" and can't get beyond that. Everything work fine on my old Mac. Any Ideas?

Chasel please see Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html for information on how to resolve download errors.

I can't get my blade tool to work in Final Cut Pro X 10.0.7

I can't get my blade tool to work in Final Cut Pro X 10.0.7. I magnify the clip to the highest zoom and when I select the blade tool, I see the icon but when I click on the clip to chop it.....nothing. The blade turns red and nothing happens. Please help.

If you are in fact in the active project window, try command B at the location of the skimmer and see whether it makes the edit.
Russ

HT204053 i have put in my apple id and password but still can not get imessage and facetime to work

I have put in my apple id and password but still can not get imessage or facetime to work please help...thanks

Please try to sign in at https://appleid.apple.com
Check if your new username/email address is verfied
If this works, delete your account on your iPhone (Settings > iCloud)
Sign back in

Can't get my Linksys E2500 to work

Similar Messages

Maybe you are looking for