Can't get my UC320W to see a phoneline

Hello,
I have a UC320w which I am trying to set up for an office. I am currently unable to get the device to see any phonelines, despite being plugged into the master socket of each one. The FXO line simply says "no-service" - I have tried all four ports) and will do no more than that.
I have tried different cables, confirmed the phone line to be good by using an analogue telephone on it and resetting the device back to factory defaults (and rebooting), all to no avail.
Has anyone got any suggestions?
Thanks,
Jamie

Hi Jamie,
This sounds like you need to load the PMF for FXO overload. This PMF fixes issues with FXO lines not being detected.If you go to
https://supportforums.cisco.com/docs/DOC-16301
You can download the FXO_Overload_disable.pmf and then go to Status>Devices>Alter PMFs in Configure Utility and apply configuration. This should fix the issue.
Regards,
Chris

Similar Messages

Bought a NuPower replacement battery, but can't get my MacBook to see it.

Hi Everyone!
Bought a NuPower replacement battery and installed it. Rebooted and the fans are running at full tilt. Did a SMC reset and a PRAM zap. Shut down. Restarted and the battery icon still has an X in it (no batteries available). Fans are running fast as well (again).
Repeated this a few times, but still can't get the MacBook to see it.
Here's the deets of my MacBook:
Hardware Overview:
Model Name:          MacBook
Model Identifier:          MacBook5,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          3 MB
Memory:          4 GB
Bus Speed:          1.07 GHz
Boot ROM Version:          MB51.007D.B03
SMC Version (system):          1.40f2

Having problems as well.
It has been less then 48 hours that I have installed the new battery and it's still not charging. It says that I has 51% of charge, but it has not pass that number in the past 48 hours. I have reset the PRAM and SMC and no change.
When I go the System Information, I see that it recognize it, but it does not what to charge:
Model Information:
Serial Number: W024902CY6GOA
Manufacturer: Newer Tech
Device Name: ASMB013
Pack Lot Code: 3230
PCB Lot Code: 30db
Firmware Version: ddae
Hardware Revision: dac2
Cell Revision: 2b39
Charge Information:
Charge Remaining (mAh): 2814
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 5505
Health Information:
Cycle Count: 1
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 11769
AC Charger Information:
Connected: Yes
Charging: No

How can I get iMovie 10 to see my iPhoto Library after I relocated it.

How can I get iMovie 10 to see my iPhoto Library after I relocated it. I moved my iPhoto Library to a secondary hard drive, because my main SSD wasn't large enough. I then upgraded to IMove 10.0.4 and also moved my iMovie Library to the secondary hard drive. When I highlight the iPhoto Library in iMovie there is nothing there. Any ideas on how to get iMove to find my relocated iPhoto Library?

I think I may have solved my own problem. I left cliked on the relocated iPhoto Library and went to "Open with >." I then went to "Other...." I then set the wind located in the bottom labled "Enable:" to "All Applications" and picked iMovie. It gave me a error, but the ultimate result was that iMove now was linked to my iPhoto Library.

Some websites keep asking to enable cookies in my browser when they are and I can't get this sites to see that, they worked fine yesturday but not now, any help

Some websites keep asking to enable cookies in my browser when they are and I can't get this sites to see that, they worked fine yesterday but not now. I've restarted the browser, restarted the computer, disabled then enabled cookies in the privacy settings and still nothing. Any help?

Hi,
Many site issues can be caused by corrupt cookies or cache. In order to try to fix these problems, the first step is to clear both cookies and the cache.
Note: ''This will temporarily log you out of all sites you're logged in to.''
To clear cache and cookies do the following:
#Go to Firefox > History > Clear recent history or (if no Firefox button is shown) go to Tools > Clear recent history.
#Under "Time range to clear", select "Everything".
#Now, click the arrow next to Details to toggle the Details list active.
#From the details list, check ''Cache'' and ''Cookies'' and uncheck everything else.
#Now click the ''Clear now'' button.
Further information can be found in the [[Clear your cache, history and other personal information in Firefox]] article.
Did this fix your problems? Please report back to us!

How can I get Siri to not see some iCal calendars?

When I ask to see my calendar, Siri shows calendars that I want to supress. I have some iCal calendars with misc info (warranties, medicines, etc.) that I turn off in iCal, off on the phone calendar. But Siri shows me (for ex: "19 meetings"" when I ask to see my calendar. How can I get Siri to avoid those calendars I have turned off elsewhere? Thanks!

If it is your own conference bridge you can create a new contact named "My Bridge" and enter your 1800 number along with a "wait" command and pass code and #. It would look something like this 1-800-555-5555;12345678#. This way when you tell Siri to call "My Bridge" she'll dial and then you'll notice an option in the lower left to dial the pass code. Press that and you're all set. You can do the same for frequent conference bridges you connect to. Hope this helps.

Can't get Jump Cut to see Beat Markers

I've watched several tutorials. I've tried this in a new project and I can ge it to work. I just can't get it to work in my existing project. I've put the music in the background where it's behind the video clips. I go into Clip Trimmer or what ever it's called and add my beat markers, but when I select the portion of the clip surrounding the beat markers it doesn't split up the clips like it does when I try it in a new project.
I've unchecked the snap menu items under view or edit. Like the snap to ends, snap to beats or whatever.
What am I missing here?
Can I create what I want in one project and copy and paste that combo back into my other project?

Might I suggest a training DVD
http://www.classondemand.net/media/final-cut-training/fcp7.aspx
This is an AVCHD camera. You need to use the log and transfer function with the correct settings. You should not use iMovie for capture as it captures in an older codec that's not very good. In FCP7 you can capture in ProRes or ProRes LT, both of which are superior.
I stand to profit from this message.

After HD crash, restoring to new HD. Library files missing or corrupt. How can I get iTunes 10 to see my music

The hard drive on my fairly new HP Pavilion desktop died hard on boot-up. HP replaced the drive the next day. Used the Recovery Disks and got the unit up and running. I have been using Memeo Premium Backup and never did get any error messages during backup. When I went to restore the data, much of it is missing or corrupt. In the Restore data on the backup drive, I can see many folders but only a few have data. I opened a ticket with Memeo and after they made a few useless comments, they closed the ticket.
Fortunately, most of my iTunes data (folders and files) were restored in-tact. The exceptions were the library files, which are missing. The library files in the Previous Itunes Library folder were corrupted. I installed iTunes 10, but there are no songs, podcasts,etc, in it. I have tried every article in the knowledgebase and tried to fix the ITL and XML files, but it is hopeless. Also, when iTunes is running, at the top it shows .iTunes Preferences.plist. So, I have a disaster and about 10 gb of music going nowhere. Any ideas? I would really appreciate any help I can get.
Brad

They are all mostly the same size at around 6MB but there are a couple that are very large 55MB (including the 30 tmp file I mentioned above. There is also one around 7KB). I tried renaming the most recent (as of 8:30PM last night) tmp file as iTunes Library.itl but when I launch iTunes, I get the "The file 'iTunes Library.itl" cannot be read because it was created by a newer version of iTunes" popup.
But when I go into a directory I created to get the most recent itl file I've been saving as a backup and copy it into the iTunes directory to replace the one that I tried to make with the tmp file, and launch iTunes, my whole library loads with no problem.
However, if history repeats itself, this will work for at most a couple of days before I have to copy the saved itl file back into the iTunes directory.

How can I get MAX (Labtop) to see my PXI system?

I have a PXI system consisted of PXI 8184 (Microcontroller) and PXI 6552. I wish to run LabView 8 application on my labtop and run it and see how the PXI device respond to my application. TO establish the communication I read that I can use a CAT5 crossover cable or a hub. I couldn't get the PXI system to show up under Remote Systems in MAX residing in my labtop.
How can I solve this problem can any body clue me on that?
Thanks

Greetings!
   1) Are you using a PXI system which has an embedded controller
with Real Time (RT)?
   2) Did controller have RT installed / shipped with it. We can
confirm that in the bios if the LabVIEW RT menu options show up?
   3) Listed below are few links you can go through to get started
and troubleshoot. Specifically the chapter 2 in the manual for 8184
http://www.ni.com/pdf/manuals/370836b.pdf
http://digital.ni.com/public.nsf/websearch/A43DD6F680D123DD86256F870002B6A2?OpenDocument
http://www.ni.com/support/install/install_hardware_5.htm
   4) When you connect a monitor to the controller what do you see in
the screen?
   5) Did you get a chance to install the embedded sw CD that came
with the controller in your host computer?
   6) You can also verify if you have a folder similar to following
in your host computer after the installation (Similar to the following)
   C:\Program Files\National
Instruments\RT Images\Base\2.0\7151
Thanks and hope this helps to get you rolling
Good luck
Avi Harjani

Can't get Apple Tv to see my Buffalo Linkstation Live, please help

Have tried everything to get the two to talk, but the apple tv does not see the buffalo drive. I have turned on the itunes server on the buffalo drive, and have verified that all folders are sharded on the drive. I am at a loss, and would really welcome some help. Thanks.

A 3rd gen Apple TV needs an iTunes library shared using Home Sharing, which means a Mac or PC based iTunes will only work.

Can't get my ATV to see my desktop PC

Can anyone give me some advice on how to set it up so I can stream my music from my desktop PC to my TV through apple tv. When I look at the computers menu on ATV, there is nothing that shows up. Home sharing is enabled on both my ATV and my desktop. My Desktop PC connects to my router via ethernet cable.

I don't see an airplay option on my Itunes. On my appletv the only thing I can find regarding airplay is under settings. Then it just asks me to turn on/off and password.
I disabled my virus symantec software. I believe homesharing is set up property. It is turned on in my Itunes on my desktop with the same account information as I entered on my appletv under settings/computers
Any other idea's for troubleshooting?

On my work computer, on the work network (not at home), FireFox can't get into gmail, nor see graphics on this site or ones like Linkedin. Settings to change?

Got a new computer at work that is very locked down. I am running Firefox off my USB since they give us only IE 8 and a very locked down Chrome that has no access to extensions,
At work (not at home), when I try to get into gmail, I get all these certificate errors. Granting exceptions doesn't work.
Another problem is when I go to sites like this one, or like Linkedin, it is all text, no graphics. But when I use this same computer on my home network, there is no problem.
Would appreciate if there is some setting I can change on this to enable access.

On your work computer, you're probably behind a proxy server. When you make exceptions and proceed to a site, often you will get an incomplete page load because many sites now use multiple servers and the exception only covers the main one.
Assuming that is the problem, you may be able to import whatever certificate IE and Chrome are using to get around this problem. (They both share the Windows certificate store.) In particular, there would be an master certificate that the proxy is using to sign its fake SSL certificates that you could export from IE and import into Firefox as an Authority. I assume this would work on a Portable version of Firefox, but I've never heard of anyone trying it.

How can I get my trigger to see the SQL that activated the trigger?

The catch here is that this is a standard edition instance so FGA is not available.
TIA, Allen

I would be very interested in why you would want the literal SQL...
While this won't be particularly efficient, you can get the SQL currently being executed in a session via something like
select sql_fulltext
   from v$sqlarea area,
        v$session sess
where sess.sql_address = area.address
    and sess.sql_hash_value = area.hash_value
    and SYS_CONTEXT( 'USERENV', 'SID') = sess.sidI haven't tested that this returns the query that actually fired the trigger in every situation, but it's probably a reasonable guess...
Justin

Can't get Windows XP to see SATA drives

Please help
SATA Drives show up in the system hardware but not in My Computer or Explorer
K8T Neo FIS2R (Updated BIOS Yesterday via Live Update)
amd 64 3000+
Centon PC3200 (2 X 512 in slots 1 and 2)
WD 80 gig ATA drive (Windows Xp Home on this drive)
2 Maxtor 250 GIG SATA Drives (tried both Raid 0 and no Raid)
All drivers from CD installed (Updated drivers via Live Update Yesterday)
Promise disabled and using VIA slots
Nvidia FX 5900 Video card

Good evening -
Thanks for the response. I loaded drivers from CD. I want to keep the operating system on the 80 GIG ATA drive and use the SATA RAID for programs. The drives show up in the device manager and in the VIA RAID utility that came with the motherboard but I can't see or access them through My Computer. I have tried to set up the RAID through both the Windows software and through the Boot program, but no luck. When I tried to update the drivers from the floppy it said no newer drivers found. (I tried to update drivers through the Device manager.) Also when I deleted the raid and tried to set up the drives individually the same thing happened. Is it possible I don't have the BIOS set up correctly? I am at a loss.
Tony

Can't get Windows 7 to see it and charge my iPad

It makes the noise but won't show up as an extra drive to copy pictures form or to it and it says not charging...
New iPad with Retina display and updated to iOS7.0.3
Help

Saying not charging is normal. Most USB ports don't put out enough power for the iPad.
When you use windows explorer can you see hte device?
You may need to update your iTunes.

No Problem hooking up Vista laptop with WRT110 Wireless Router but can not get XP laptop to see it

I purchased a WRT110 Linksys wireless router this afternoon and had no problem configuring it for my wired desktp and my wireless Vista laptop, but my Acer XP wireless laptop will not even see the network. I have tried WEP, WAP, and no security, but I can see the neighbors routers but I can not see mine. My XP laptop is an Acer 3680-2574 with a Broadcom 802.11g network adapter.

Is the SSID enabled on the router ?
What is the firmware on the router ?
Click here to check the updated list of firmwares.
For information on upgrading the firmware on the linksys routers :
http://linksysfirmwares.googlepages.com/upgradingfirmware
For information on wireless security :
http://linksysfirmwares.googlepages.com/wirelesssecurity
C | EH
linksyshelp.blogspot.com

Can't get my UC320W to see a phoneline

Similar Messages

Maybe you are looking for