Can't get my WRT300N router to work

I am new to wireless networking. I have followed the instructions on the user set up disk to install wireless connection for my new Linksys WRT300N. The router seems to be working but there is no internet connection and the message that pops up is "Windows was unable to find a certificate to log you on to the network".
I am able to use the wifi connection using my older router (not Linksys) for wireless-G but I need to upgrade to wireless N for better and faster connectivity.
What I am doing wrong?
Thanks,
dotechan

That's caused by improperly setting the encryption to WPA-RADIUS
Instead of WPA-PSK on the client. The router and the client are both
Trying to find a RADIUS server with which to authenticate. Since you
Don’t have one; Change the Encryption to WPA-PSK (pre-shared key) on both ends....
See if it works ....

Similar Messages

Can't get my WRT54GS router to work

I have a few-years-old WRT54GS that was set up and working for months, then put away when my new ISP provided a router with their DSL modem. Now I'm on a cable ISP which supplies a modem but not a router, so I want to use the Linksys model. I've set it up but the Linksys router won't connect to the internet, even though my computer indicates that I have an "excellent" signal from the router. I thought that pressing the re-set button would revert the router to its "first time" setup state, so I could run the setup disk, but that doesn't work: still no internet. The router is out of warranty and Cisco wants me to buy a new one, or charge just as much to provide technical support. I'd prefer to solve the problem without further enriching Cisco. Can anyone help me out?
Solved!
Go to Solution.

Bypass the router and connect the computer directly to the cable modem.
Make sure that your computer can access the Internet when connected directly to the modem.
Connect the modem to the Internet port and computer to Ethernet port 1 on the router.
Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and reconfigure it.
Follow this link to configure Linksys router with the Cable Internet service.

Can't get my epson sx535wd to work. my epson will get contact with my router (sitcom wl306) and my mac is on wifi, but they can't connect. epson can't find the computer and my report says: there are conflicting channels on my router or entry point. help

can't get my epson sx535wd to work. my epson will get contact with my router (sitcom wl306) and my mac is on wifi, but they can't connect. epson can't find the computer and my report says: there are conflicting channels on my router or entry point. please help

OK, let's try these................
1 - Boot up from your install DVD and run "Repair Disk" from the Utility menu. When done, restart back to your desktop, repair permissions and restart your computer. Re-connect your printer.
2 - Download & install the Gimp drivers. Make sure the one you install is compatible w/your OS-Gutenprint 5.2.8-pre1. Repair permissions, restart your computer & re-connect your printer when done.
The Epson model I have, in order to get it to print wirelessly, I had to install a Gimp driver.
3 - Check out the following KB Articles:
Mac OS X 10.4 Help: Connecting to a network printer
Epson Printer Drivers v2.10 OS X
Adding a printer to your printer list in Mac OS X
Mac OS X 10.4 Help: The printer I'm adding says "Driver not installed"
======================
If still unsuccessful after trying all of the above, the problem could be your iBook or human error. You can either call Epson & ask to speak with a Mac savy supervisor or return the printer & find another that is compatible w/your current OS.

Can't get wake on lan to work on Hp n40l microserver

Hello
I installed arch on my HP proliant microserver and I can not get Wake on lan to work. I tested my device with ethtool and it supports and is enabled for WOL with g value set for both.
But whenever I power it off by systemctl poweroff I can no longer see it as a connected device to my router
Before installing arch I tried ubuntu for testing the hardware quickly and I got wake on lan working there. I can not figure out what might be the issue here. Wake on lan is enabled in the BIOS.
Any help would be appreciated
Cheers

As I see in the Archwiki , the wol package would also need the IP address ( though not necessary ) along with the mac address of the server.
I fear that the nic on the server does not obtain an ip in shutdown state, since I can't see it in my attached devices in the router settings( I could be very wrong ! )
Tried using wol on a laptop running arch, but with no luck.
I have seen this workaround in several places
https://bugs.launchpad.net/ubuntu/+sour … bug/981461
I even tried creating a similar script which would first do
ip link set dev enp2s0 down
systemctl poweroff
but that did not work either.
Cheers
Last edited by ayushjsh (2013-04-03 07:00:28)

When our iPad is in use on the internet, my iMac internet connection goes off. I can't get the two devices to work at the same time with the AirPort Express. Is there a setting somewhere I may have missed?

When our iPad is in use on the internet, my iMac internet connection goes off. I can't get the two devices to work at the same time with the AirPort Express. Is there a setting somewhere I may have missed?

When two or more devices conflict it typically means that the DHCP service is either misconfigured or is not running at all. DHCP provides IP addresses to local network clients.
Is your AirPort Express base station the only router in your current network configuration? That is, is it connected directly to an Internet modem and not to another router upstream of it?

I can't get Norton Safe web to work. (I've just upgraded to Norton 360 from NIS 2011 on which Safe web worked OK).

I can't get Norton Safe Web to work inFirefox since I upgraded to Norton 360. I was previously running NIS 2011 and it worked fine then.

Actually when you have created an ad hoc network using Internet Sharing your Mac is supposed to have a self-assigned IP.
What I suggest that you do is turn everything off on the Mac and tell the iPad to forget the Internet Sharing network, then restart the Mac and the iPad. Next slowly restart Internet Sharing on the Mac and when that is set up corectly try to connect to the network from scratch with the iPad. If you password protect your Internet Sharing network I suggest that you use the Other... option on the iPad; enter the network's name, select the correct protection scheme and finally enter the password and Join.
This issue should have nothing to do with your modem or router, this is all Mac and iPad.

How to get the wireless router to work when i change to new modem and internet connection

I already set up my wireless router in my macbook but then moved to a new house and basically have a new internet connection. My internet connection is fine when i connect the ethernet cable form the modem to my macbook. But when i plugged in the wireless router, my computer sees it but will not connect to the internet. I lost my installation CD and i tried to re-install using the dowloaded installation but it goes into error saying i can't re-install if i don't change back to default.. anyway, maybe the solution is simple but it eludes me so please help!
In summary:
1. same macbook
2. same wireless router
3. same internet provider but new connection and modem (since i moved to a different house)
how do i get my wireless router to work? thanks!!!

Who is your Internet Service Provider(ISP)?
If you have a cable connection then follow this link and if you have a DSL connection then follow this link to configure your router.

Can't get brand new WRT610N to work with Billion 7404 VGOM

I already posted this on whirlpool, here are my posts:
Hey All,
Just bought a LinkSys WRT610n and I can't get the darned thing to work with my Billion 7404VGOM.
At the moment I just want to network my pc to the LinkSys, LinkSys connects to my 7404 which is connected to the internet.
I've tried using DHCP automatic connection with the WRT610N, but it just doesn't talk route any traffic to the 7404...and thus nothing to the internet.
All cables and plugged in correctly, I tried the auto setup also but just can't figure the thing out.
Any suggestions?
Cheers,
Ken
I can't ping my 7404 modem from my PC when connected through the WRT610N. I can ping the WRT610N successfully, but when trying to ping the 7404 the WRT returns "Destination Host Unreachable"
7404 is function fine if I just connect to it directly though.
I don't understand, even If I couldn't get DHCP info working or syncing between both devices, it should still be able to ping it.....?
Right, I just plugged in my netbook via network cable into the "Internet" port on my WRT610N. I try to ping the router using this (it doesn't get any DHCP settings from the router, so I just set it manually and use the WRT as default gateway ip)...I just get request timed out.
I should be able to do this right?....starting to think my WRT610n has a dodgy "Internet" port.
Any suggestions?

If you connect your notebook via network cable into the "Internet" port on the WRT610N and if you ping the router it will not reply...also your Notebook will get any DHCP setting with this connection...However what exactly is Billion 7404VGOM ? A modem i guess!! Who is your ISP ?

AirPort Time Capsule. Read everything and tried everything. Can't get a guest network to work. Switched from bridge mode and still doesn't work. Anyone able to set up a guest network?

AirPort Time Capsule. Read everything and tried everything. Can't get a guest network to work. Switched from bridge mode and still doesn't work. Anyone able to set up a guest network?

I had a bright house cable modem that also had built-in wi-fi.
Don't mean to be picky here, but if the "modem" had built in Wi-Fi, it was not a modem. It was a modem/router, also known as a gateway type of device.
A device like this combines the functions of a separate modem and separate router in one package. Turning off the wireless on a device like this does not make a it modem.....it is still a modem/router or gateway with the WiFi turned off.
I think that if I have them replace the current "complicated" modem with a "simple" one I should be able to get the guest network up and running.
That would be correct. Hopefully, they offer this type of option for their customers.

Want to take back because i can not get my ipod touch to work on this

I can not get my ipod touch to work on this Linksys WRT54g router at all.I called them and was on the phone for a hour and still can not get it to work.And it is not the ipod because if i go outside i can get on with someone router outside.Can someone Please Please Help Me with this i would like to be able to use my rounter.
Regards
Chippy

Chippy:
I'll assume you've read the iPod manual. The directions I have seem fairly straightforward - iPod connects to a wireless network when it discovers one. Or, if that option is turned off, you have to manually connect it.
When it comes to attaching to your router, you will need to know what kind of security the router is using, what the security password is and most important - the router's DHCP function must be activated so the iPod can acquire an IP address.
If the iPod truly can handle the connection, and you have the necessary information I mentioned, it should connect without a problem. But since you can't connect, you need to review the settings I mentioned.
It's possible there is some sort of issue with the router and the iPod. But it's my guess that the iPod is not acquiring an IP address because the router is not giving them out.
Check these things out and post what you find. If we can figure out the answer, your post will be helpful to others who may run into the same problem.

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone an i have internet and all other functions working on my computer

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone and i have internet and all other functions working on my computer

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, look under User Diagnostic Reports (not "Diagnostic and Usage Messages") for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents—the text, not a screenshot. I know the report is long. Please post all of it anyway.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

How can I get my web cam to work in Adobe Connect ?

This is actually an end user's question that I am having trouble answering to...
We use Adobe Connect to give online language classes, the end user is one of the students.
I cannot find the right Support answer to give him.
Problem:
My camera does not work when I connect to Adobe's rooms but camera works fine with other software.
Even though I suspected my old camera was working fine, yesterday I went ahead and bought a new camera.
I thought perhaps my webcam software may have been a problem, so I bought a different type camera with different software.
Even after removing all the old software, same result:
I surmised the problem might be caused by my firewall and security software, so once I tried changing the permissions for Adobe, and my Webcam, but that didn’t work.
Another time, I restarted my computer right before class and then turned off my firewall completely so there would be no interference but to no avail. I’m totally perplexed.
Isn’t there anyone else experiencing a similar problem?   Has anyone else found a solution?
I run Windows Vista with McAfee Internet Security Software. I always reboot the computer before class and open no other programs other than Google Chrome.
I now have a brand new Microsoft LifeCam Cinema Camera with LifeCam 3.5 Webcam Software.
I test my camera before going online. It always works fine.   Then I shut down the camera program and login into class.
When I “connect webcam” in the room, the light on my camera comes on (suggesting that it is ON), but only a black image is transmitted to the room.

Check to see if you have Google Voice installed. If so, remove it and see
if your problem vanishes. If not Google Voice, check to see if you have
any other communications software which interacts with your cam and
disable it. This was the problem I had with a similar problem on a Mac.
MosesJOI <[email protected]>
10/13/11 12:08 PM
Please respond to
[email protected]
To
jsb152 <[email protected]>
cc
Subject
How can I get my web cam to work in Adobe Connect ?
Re: How can I get my web cam to work in Adobe Connect ?
created by MosesJOI in General Discussion - View the full discussion
Thanks a lot Heyward for the swift reply !
I sent the advice out to the end user, but unfortunately this wasn't the
solution.
His reply is below :-
The default resolution of my new camera is already set at 640x360, but I
went ahead and tried several lower resolutions (e.g. 424x240; 320x240; and
160x120) but none worked in the room - camera still showed up as black
blank screen. Also, as far as I can tell, I don’t have the option of
adjusting the frame rate.
I started playing around with my Internet Security Settings to see if they
might be playing a role. So far, all to no avail.
Hmm...quite a tricky one - webcams always are - maybe if he can find a way
to adjust the frame rate (?).
He's going to fiddle about with the settings a bit more and see if
something does the trick.
If anyone has had a similar problem and found an ingenious solution,
please jot on a note on this thread.
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either
reply to this email or visit the message page: [
http://forums.adobe.com/message/3969561#3969561]
To unsubscribe from this thread, please visit the message page at [
http://forums.adobe.com/message/3969561#3969561]. In the Actions box on
the right, click the Stop Email Notifications link.
Start a new discussion in General Discussion by email or at Adobe Forums
For more information about maintaining your forum email notifications
please go to http://forums.adobe.com/message/2936746#2936746.

How can I get iCloud to accept my working Apple ID and password

My Apple ID and password works for iTunes and App Store. I'm trying to set up iCloud on my iPhone and iPad but i keep getting an error message that reads unsupported ID. Apple ID must be in the form of email address (@me.com). I don't have a MobileMe account. How can I get iCloud to accept my working Apple ID and password?

I've also reset my password to my Apple ID. I still get the Unsupported ID and password.

Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.

Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.

Hi deamayfield,
Thanks for visiting Apple Support Communities.
If your Music app is unresponsive, try restarting/resetting your iPhone:
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
Best,
Jeremy

I just got a new itouch and i can't get imessage or facetime to work on my home network

I just got a new itouch 4 and i can't get imessage and facetime to work on my home wifi network (Airport Express). I can't explain it. The itouch works fine otherwise uncluding the internet. Facetime and imessage work at the apple store so there must be something wrong with my home network. Please help if you can!
iPod touch, iOS 5.0.1

I changed the DNS to 8.8.8.8 as you suggested with no success, I even tried 8.8.8.8, 8.8.4.4 as suggested by others with no success either. When I try and activate iMessage or Facetime, I still get the same message "could not sign in, please check your network connection". The internet and Mail work perfectly fine on the iPod touch so the WiFi signal IS going through. I am at a loss, any other suggestions would be more than welcome. Thanks!

Can't get my WRT300N router to work

Similar Messages

Maybe you are looking for