Can't get past gray screen

I posted earlier about a problem that resulted from installing the usual software updates that pop up periodically. Initially I posted that after the restart, the screen was blue with a wide black vertical line on the right side. With closer observation I noticed that before that happens, the screen kind of changes color from a purplish tint. If I leave it powered on, the blue screen with the black line eventually disappears and it just becomes a gray screen. Because I haven't seen any icon of a blinking question mark I still have hope that my hard drive isn't dead! Can anyone please offer any advice?
I have tried starting it in safe mode but nothing happens. I also tried holding command/option/P/R and that just did the same thing with the line.
I am looking for my original disks but have not found them yet!

1) try to boot from the install cd-dvd
(if this doesn't work)=>
2) Try to connect it to an external monitor. (if this shows an image on the external display your lcd is broken)
(if this does not show an image) =>
3)your motherboard is probably
broken (that is the graphics card integrated on your motherboard)

Similar Messages

  • Can't get past gray screen with file icon on it

    When i turn on my computer the power light goes out but the gray screen stays on. After two or three minutes an icon of a file with a question mark appears. I cannot get past this screen. I have removed my battery and tried again. I have also tried the other processes for a computer that won't turn on. In my case the computer does turn on just never gets past this gray screen. Please someone help me

    The question mark on the file tells you that your MacBook wants to start up but can't find a viable OS to start from. Can you start up from the DVD that came with your Mac? If so, go to Disk Utility and see if you can repair the internal hard drive. If you can't see the hard drive from within DU, your drive may have failed, and you may need to replace it. Good luck.

  • Can't get past gray screen with progress indicator... Help

    I can't turn on my Macbook. It starts but won't go past the gray screen with the progress indicator (spinning circle).
    I have tried:
    1. turning off, removing battery, holding start for 5+ seconds, replacing battery and then turning on.
    2. Holding command + option + R + P while staring up, waited for 3+ chimes.
    3. holding Shift down while starting up
    none of these things are working.
    I've been on hold with apple service/support for almost an hour now.
    I have an assignment on the computer that is due by midnight.
    HELP!
    I'm not very computer savvy and this is my first mac.
    Any ideas folks??
    Thanks.
    Macbook   Mac OS X (10.4.7)  

    You've done all the standard procedures. If you have any peripherals attached, disconnect them.
    This describes resetting the PMU:
    http://docs.info.apple.com/article.html?artnum=303319
    Did you have the AC disconnected when you did it? I don't have any other ideas.
    These are the startup key options:
    http://docs.info.apple.com/article.html?artnum=303124
    Edit: If you have the install disc stuck in it anyway, can you get the hardware test to work? (Reboot while pressing the D key.)

  • Can't get past gray screen for OS X but will boot into Windows partition.

    Hi- I am really desperate for help here.
    Restarted my computer this evening when Front Row wasn't able to find the files on my external HD. When it booted it went directly in to my Windows Boot Camp partition. So I restarted, held down 'option', choose my OS X disk and just got the spinning sun icon on the gray screen for several minutes. It then booted into Windows again. If I hold down 'option' again I can cut it off before it gets to Windows.
    I've tried booting into a cloned HD via FireWire and same results.
    I've tried booting with the install disk (c key held down) and it won't recognize it.
    I've tried Safe Mode (shift key) - same.
    I've booted into Single User and done fsck and and it says everything is ok.
    - BUT I did notice it says further up- "BSD: rootdisk0s2, major 14, minor 2". Are these errors? If so why didn't fsck find and fix them.
    I've tried resetting PRAM and SMC.
    The only thing I have done out of the ordinary was an hour before I was trying to get some of my files on my wife's laptop and went into permissions on my HD and changed "Everyone" Priviledges to Read (or maybe it was Read and Write) then chose "apply to enclosed items". This change took about 20 minutes.
    The computer is, of course, just over a year old and has worked perfectly up until now.
    Someone-Please!!!

    Tried that and it just doesn't read the disk. I've booted it with the disc already in and held Shift and also tried it with "C". The same for putting the disc in just as it boots up.
    I went into Single User mode again and compared the text against what shows up on the laptop. Their are a few differences. At the very beginning of the iMac text there is:
    npvhash=4095
    hi mem tramps at 0xffe00000
    PAE Enabled
    64 bit mode enabled
    -then-
    Extension "com.apple.driver.AppleACPIPlatform" has immediate dependencies on both com.apple.kernel and com.apple.kpicomponents; use only one style.
    Extension "com.apple.driver.AppleIntelCPUPowerManagement" has immediate dependencies on both com.apple.kernel and com.apple.kpicomponents; use only one style.
    -then- after "MAC Framework successfully initialized" comes this three times...
    Extension "com.apple.driver.AppleACPIPlatform" has immediate dependencies on both com.apple.kernel and com.apple.kpicomponents; use only one style.
    These are really the only major differences that I can see in the Single Mode screen.
    I also have tried booting from the Firewire drive clone on the laptop but it is not an available option for booting. The disk partitions mount but have a lock in the corner and say they cannot be opened because I have insufficient access privileges.

  • Can't get past gray screen after Boot Camp Assistant

    So last night I decided it was time to start experimenting with Boot Camp and Windows XP Pro. I fired up Boot Camp Assistant and allocated a 32gb partition of my HD for the XP install. When prompted, I put in the XP Pro CD and restarted. It booted into the XP install utility, but when asking about which partition to use, instead of the 32gb partition, all I saw was a 131gb partition. Thinking that it was my OS X partition, I decided to cancel out of the install and do some more investigating. When it restarted, all I got was a blank gray screen, no spinning gear, no logos, nothing. When rebooting while holding down a mouse button, I was able to eject the Windows XP cd. Here's what I've tried so far:
    CDs: Leopard, Original OS X Disk 1, Windows XP, None
    Keys: none
    Result: Gray screen
    Keys: option
    Result: Gray screen with mouse pointer that initially is moveable, but then freezes
    Keys: c
    Result: Gray screen
    Keys: d
    Result: Gray Screen
    Keys: shift
    Result: Gray Screen
    Keys: command + r + p
    Result: Gray Screen
    Holding power button
    Result: Long tone while starting up, then gray screen.
    What can I do?? I'm thinking that Boot Camp fried my HD partition data, but I can't seem to access any of the boot disks or any sort of disk utilities

    I did. I took it into the Apple store and they replaced my hard drive. It was under warranty, so it wasn't a problem. I got them to give me my old hard drive back, which I hooked up to an external SATA enclosure. My mac recognized it, but said it wasn't initialized. I downloaded Data Rescue II and it recovered all of my software. I'm now using it as a Time Machine disk.
    After further research, I found out the my main problem was that I used Windows XP SP1. You NEED to use SP2, otherwise, this problem will occur. I figured I could just upgrade later, but nope, you need a native SP2 disk.
    If your Mac isn't under warranty, try this post:
    http://phail.net/2008/04/10/bootcamp-windows-xp-sp1-epic-phail/
    and his solution:
    http://phail.net/2008/04/13/bootcampsp1-white-screen-of-death-a-solution/
    In short, you need another Leopard computer. I bet if you print out the instructions and take them to the Apple store with you, the Genius Bar will help you, they've always been super helpful/nice with me.
    Good luck!!

  • I can't get past white screen when starting up, any ideas?

    I Can't get past white screen when starting up, any ideas

    http://support.apple.com/kb/TS2570 Mac OS X: Gray screen appears during startup
    ===============
    When posting in Apple Communties/Forums/Message Boards.......It would help us to know which Mac model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
    CLICKY CLICK---> https://discussions.apple.com/docs/DOC-3602
    CLICKY CLICK-----> Help us to help you on these forums

  • I recently installed iTunes on my new HP laptop computer, authorized it according to the instructions, but now can't get past a screen that tells me that I need to authorize the computer.  I purchased an album and it's in the library, but it won't sync.

    I recently installed iTunes on my new HP laptop computer, authorized it according to the instructions, but now can't get past a screen that tells me that I need to authorize the computer.  I purchased an album and it's in the library, but it won't sync.

    Have a look here...
    http://support.apple.com/kb/TS1389

  • How to get past gray screen on MacBook?

    How to get past gray screen on MacBook?

    Here are some initial things to try.
    http://support.apple.com/kb/ts2570
    http://lifehacker.com/how-to-troubleshoot-the-four-most-common-oh-sh-t-mac-48708 0511

  • Macbook keeps restarting, can't get past icon screen

    I had to correct my permissions because I couldn't edit my address book and ical. Everything was working fine last night after I did the permission fixes. But when I booted up my Mac tonight, the farthest I could get was the white screen with the Apple icon and the animated circle. After a few minutes, the laptop will reboot itself and continued to do that for 30 minutes. I can't get past that screen. What is going on? How do I fix this? I finally turned off the Mac and am using my Dell.

    The question mark on the file tells you that your MacBook wants to start up but can't find a viable OS to start from. Can you start up from the DVD that came with your Mac? If so, go to Disk Utility and see if you can repair the internal hard drive. If you can't see the hard drive from within DU, your drive may have failed, and you may need to replace it. Good luck.

  • My old iMac and OS 10.4 will not accept the New iTunes Version 10 application and I can't get past the screen offering to download iTunes 10.  This is wrong and I need help getting past this situation. Help!

    My old iMac and OS 10.4 will not accept the New iTunes Version 10 application and I can't get past the screen offering to download iTunes 10.  This is wrong and I need help getting past this situation. Help!

    Sure, you can get around it if you don't need the newest version of iTunes. I still use version 7.5 because the newer versions didn't strike me as offering anything I needed.
    If you do need a version 10-something then you will have to upgrade your operating system to Leopard (fi your computer will support it) at least.  If you need 10.5 for some reason then there's no getting around it, you will have to buy a new computer.

  • On my wife's iPad mini I can't get past the screens accepting the software license to upgrade over WiFi

    On my wife's iPad mini I can't get past the screens accepting the software license to upgrade iOS over WiFi.
    Works if I do it over iTunes on my desktop.
    I get the screens to agree to the software license (twice) then it sits there until I get impatient. like 30-60 seconds. Have tried a hard boot but have to connect it to the computer each time. Latest was when I upgraded to 8.2

    Solving the iTunes Installation Problems in Windows
    1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
    2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80.

  • HT1349 Successfully loaded ios7 to iphone 4S from iTunes...now iphone asks me to agree to terms and privacy, then it locks up and won't accept my "agree." Goes in a loop and can't get past this screen.  Pls help.  thanks.

    successfully loaded ios7 to iphone 4s.
    now iphone asks me to agree to terms and privacy, then it locks up and won't accept my "agree."
    goes in a loop and can't get past this screen.  Pls help.  thanks.

    Have you tried resetting the device?
    Hold down the home and lock buttons until you see an Apple Logo, then release the buttons.
    If that doesn't work, you should check to see if you have a backup because you may have to restore your device.

  • Trying to install Acrobat XI Pro.  On my Mac, I get the message, "Please close the following applications to continue: - Safari.  Safari is closed, but I can't get past this screen.  Each time I click "Retry", the message reappears.

    I am trying to install Acrobat XI Pro.  On my Mac, I get the message, "Please close the following applications to continue: - Safari.  Safari is closed, but I can't get past this screen.  Each time I click "Retry", the message reappears.

    TErminate the processes in activity monitor an/ or configure Safari tomnot use the quick launcher and automatic update check so that those processes aren't used to begin with.
    Mylenium

  • My iPhone gone mad can't turn off voice control which turned on by itself now can't access phone as can't get past my screen lock! Also it keeps calling random people in my contacts help please

    iPhone 4 gone mad voice control taken over phone, can't get past my screen lock it won't  respond at all, keeps dialling random people won't do anything at all!!! Even when go on voice control screen and hold power off and home screen down nothing No response. Help please? My mother very sick in hospital and need my mobile!!

    Have you tried to power off and on?  If that doesn't work and the reset didn't work, have you tried connecting to iTunes to see if it is recognized?
    If none of this works you probably need to visit an Apple genius bar and have it checked out by the techs.

  • HT1551 Want to play tv shows purchased on iPad on Apple tv. When I touch icon for apple tv and choose "apple tv" it asks for an apple tv password. We have never set up any password and can't get past this screen. Does anyone know how to find this password

    Want to play tv shows purchased on iPad on Apple tv. When I touch icon for apple tv and choose "apple tv" it asks for an apple tv password. We have never set up any password and can't get past this screen. Does anyone know how to find this password?

    You can remove the Airplay password from the Settings menu on your AppleTV.

Maybe you are looking for

  • Is there an APP to monitor call usage and number of texts sent

    Is there an APP to monitor call usage (in minutes) and number of texts sent etc so I can ensure I am keeping within my contract? I am getting my 3GS on Thursday so do not know if the phone has this facility already inbuilt or whether there is an app

  • Exchange calendar invitations accepted in IOS remain "new" in iCal

    My work calendar and email is based on Exchange. I manage both from a Mac (using Outlook 2011 for Mac) and an iPhone 5 running IOS 7.latest. It works just fine. If I accept an invitation on any platform is is accepted on all. Then I look at OSX Calen

  • How do i find dataloss in Data Guard?

    We are using redo log, in async mode, following is our setting. SERVICE=xxx_sb max_failure=100 reopen=600 LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES,PRIMARY_ROLE) DB_UNIQUE_NAME=xxx_sb When i query V$managed_Standby for delay_mins, its always zero. Meanin

  • Bluetooth won't turn off or on.

    At times, my blue-tooth is very finicky. When I try to connect a mouse, and I disconnect the mouse, and turn off the BT, I have to RESTART my Mac before BT can be turned on again. If I don't restart the Mac, the blue-tooth will be in a perpetual "tur

  • How to attach files to a business partner in CRM

    Hi experts, The aim is to develop a program with the same functionality as the way CRM  attaches files to business partners (via a browser). For example, I want to attach an excel file ( or whatever ) to a given Account ID via a program, so when refr