Can't get Pioneer DVR-110D to work

I just bought a Pioneer DVR-110D drive and installed it, but I can't get it to support burning. I tried PatchBurn 1 (I use OS 10.2.8) but to no avail. I searched this forum for posts on both PatchBurn and the drive, and I've been doing everything as detailed in the posts, but the system profiler still says burning isn't supported.
It reads CDs fine, and DVDs show up on the desktop (I don't have DVD playing software, though). It even erased a CD-RW.
In PatchBurn, there's 7 different Pioneer drivers listed, do I have to try replacing every one?

"In PatchBurn, there's 7 different Pioneer drivers listed, do I have to try replacing every one?"
In PatchBurn 1, try selecting the closest model number of Pioneer DVR drive from the list (if I remember, DVR-104). After it's unstalled, restart.
If that didn't seem to work, try a PRAM reset.

Similar Messages

Pioneer dvr-110d installed but not working properly

hello,
i'm new to the forum. i just purchased a pioneer dvr-110d for my my powermac g4 466mhz. it plays dvds correctly but the only thing that it doesnt do is load my osx 10.4 disc. i got the drive so i can install software without borrowing an external drive (i needed to reload my 10.4 because of other errors) so everytime i put the 10.4 disc in it reads it and says to restart but when that happens it restarts to a gray and sometimes blue screen. so the only way i get the disc back out is with restarting with the shift key held down and then i can force eject it. you guys are my last hope. it seems to working fine except with the startup disc. which is so strange to me.. and the system profiler recognizes it also

Hi
When you installed the drive, did you set the jumper block on the left rear of the drive to "Master"?
Have you set Energy Saver to sleep NEVER & unchecked HDD sleep?
Have you tried starting up w/ the "C" key?
Have you tried updating the drive firmware? Search Discussions for DVR-110, there are many threads with links to updating on a Mac.
Assuming you've also tried cleaning the install DVD, and updating firmware makes no difference, you should try booting from some other installer CD/DVD, to confirm that the drive is bootable; if it will not boot ANY installers, I would return it.
EDIT: you may want to also try
resetting PRAM & NVRAM, always a good idea when replacing hardware.

Help needed to track down Problem in tiger with Pioneer DVR-110D

ok as i stated in another topic i own a Beige G3 AIO that is running OS 9.2.2 and OS X 10.4.8 and i have done allot to this system to get it to run faster and to run properly.
part of this setup has a Pioneer DVR-110D it there and when i bought it i was running OS 9.2.2 only. at first i could not burn anything with it cause it wasn't supported and when i went to put the system to sleep it would freeze when i would wake it up it never did this before i installed the drive so i knew what was causing it.
i turned off HDD sleep and the problem was fixed. but i didn't like the ideal of having the hdd running all the time when idle. me and a friend was talking about optical drive issues and he said he found this driver replacement for the apple cd/dvd driver called intech speed tool's 6.0 for OS 9.2.2 and that i should give it a try cause it fixed a few problems for him.
i downloaded the demo of it and installed it and i turned on hdd sleep and put the system to sleep and woke it back up and the system was running great. so now the wake up freeze problem was cured. but still no burn support. so after a few weeks of posting on here about the problem some one came by and said he knew what the problem was and sent me a modded PioneerCDR authoring support extension. i installed it and rebooted and opened iTunes and iTunes showed Pioneer DVR-110D as the devise to burn to. so i tryed it and behold it burned a audio cd with no problems.
later i bought a western digital SE 120gb hdd and installed it and partitioned it 3 times a 8gb first partition for OS X a second partition 10gb for OS 9.2.2 and the 3rd partition was the rest of the drives size for shared data and storage. the hdd worked great with no issues so it was time to try OS X on this system cause i was waiting to get a large HDD to do so.
i figured that the Pioneer drive would not boot the OS X jaguar cd and is a known problem with non apple cd rom drives. so i took out the Pioneer and reinstalled the apple 24x stock cd rom drive. and the jag install cd booted without a hitch. Jag installed and was running so i updated to 10.2.8 and found out the internal screen kept going out and locking the system up. so i searched this forum for the onboard video blackout and came across the terminal work around to get the system to behave itself with having more than 192mb ram installed. i rebooted and all went fine afterward.
i reinstalled the Pioneer drive and went to testing it all was fine everything mounted on the desktop that i put in the drive. but i lacked the ability to burn with the drive cause still the drive wasn't supported be the system so i searched the forum and came across the program called patchburn. i downloaded it and ran it and patched the driver to support iApps burning with this drive. so i put in a blank cd and went to burn in iTunes it burned flawlessly so i tryed a dvd-r with the finder it to burned flawlessly.
o loved playing a game planeshift and then they stopped supporting 10.2.8 so i went to buy the tiger install cd's. i already knew the Beige G3 was not a supported version of Os X on this system and you had to use xpostfacto 4 to install tiger on this system. so i did what i had to do to install tiger on the system and selected use old NDRV and selected to install tiger. which installed some files to boot tiger and rebooted yet again the Pionner drive refused to boot the install cd's . i got mad and held down the command option power key's for about 10 seconds and let off. the tiger installer booted and got to where it started to copy the files to the hdd and stalled out and the drive spun down never to spin back up or show signs of life so i powered down the system and removed the pioneer drive and put the stock 24x cdrom in and installed tiger.
after tiger was installed i shut down the system and installed the pioneer drive. and powered back on and it was in verbose mode showing what was going on one part showed that the Pioneer drive was detected but had no kernel dependencies and continued to boot. i went to repair the permitions when the onboard video went blank and the system locked up. i rembered that 10.2.8 did the same thing so i tried the 10.2.8 screen blackout fix in 10.4 and rebooted. the onboard video didnt come on but since i had a ATI Radeon 7000 i could work around in tiger to update to 10.4.7 at the time. i first repaired permitions and then ran software update and updated everything and rebooted. the onboard video came back on allong with the ATI Radeon 7000 which being used as boot video device and shown the gray apple logo with the spinning pin wheel at the bottom.
so far tiger was running great so i put a disk in the drive and nothing it didn't mount anything so i ejected it with the button on front of the drive and tryed a dvd movie and got the same nothing as with the cd. so i rebooted with the dvd in the drive al behold tiger mounted the dvd but as soon as i would try to do anything with it the drive would stop and i would have to reboot the system to gain the drive back so i can repair permissions. and never tryed to use the drive again
10.4.8 update came out i updated to it using software update and rebooted. the update went flawless so i thought to myself what if the pioneer drive worked now. so i put a cd in the drive and it mounted the disk. then i ejected it with amazement and put a dvd in and it to mounted. so i tryed to play the dvd and it played the dvd to the end of the movie. i took out the dvd and rebooted. i tryed to put the dvd back in but it didnt mount. which ****** me off as to why it was just working and now its not.
i rebooted and the dvd mounted as soon as the desktop showed up so i tried to play it but this time it only played for about 10-13 minutes before the drive stopped spinning which made dvd player stop responding which made me have to force quit the dvd player and try to restart which gave me a kernel panic. so i forced restarted (got a forum to send to apple to report the KP so i did) and the dvd mounted once again as soon as the desktop showed so i ejected the dvd and put a audio cd in and it mounted and i played the hole cd. so i ejected that and put a blank cd in and treed to burn and it got to 30% and then the drive spun down and made the disk utility stop responding. so i forced quit disk utility and rebooted. once it rebooted nothing popped up so i pressed the eject button on the drive and the cd r came out.
the OS X 10.4.8 update made the drive more stable but still wont burn anything. some times it will still not mount anything, some time it will not play anything, and still fails to copy files over to the hdd. so now im left to believe its a driver issue some where since this drive worked so flawlessly in jaguar and OS 9 but fails to work properly in tiger.
i looked in the extensions in ASP in 10.4.8 and there is a few extensions showing errors. i made a list of them to show
PatchedAppleNVRAM:
Version: 3.0
Last Modified: 8/9/05 6:07 PM
Location: /System/Library/Extensions/PatchedAppleNVRAM.kext
kext Version: 3.0
Load Address: 0x4db000
Valid: Yes
Authentic: Yes
Dependencies: Incomplete
Dependency Errors:
com.macsales.iokit.OpenOldWorldNVRAM: No valid version of this dependency can be found
Integrity: Unknown
OpenPMUNVRAMController:
Version: 2.0
Last Modified: 8/9/05 6:08 PM
Location: /System/Library/Extensions/OpenPMUNVRAMController.kext
kext Version: 2.0
Load Address: 0x63a000
Valid: Yes
Authentic: Yes
Dependencies: Incomplete
Dependency Errors:
com.macsales.iokit.OpenOldWorldNVRAM: No valid version of this dependency can be found
Integrity: Unknown
GossamerDeviceTreeUpdater:
Version: 3.0
Last Modified: 8/9/05 6:07 PM
Location: /System/Library/Extensions/GossamerDeviceTreeUpdater.kext
kext Version: 3.0
Load Address: 0x63d000
Valid: Yes
Authentic: Yes
Dependencies: Incomplete
Dependency Errors:
com.macsales.iokit.OpenPMUNVRAMController: No valid version of this dependency can be found
Integrity: Unknown
that is the list of extensions that are reporting some sort of errors. at first i was figuring it was a problem with the driver for the Pioneer drive but my friend brought over his digital audio G4 which was also running 10.4.8. and we decided to try the drive in his Mac to see if there was any problems. it mounted everything we threw in it. it played dvd's great and played audio cd's great, it copied files over to the hdd without fail. it even burned a flawless cd. ok now the ideal of the driver for the drive was thrown out the window. so it has to be something else causing the problem. either a driver for a part on the motherboard or what i have no clue.
im just wondering what driver it would be causing a problem not allowing the Pioneer drive to work properly. cause its not the drive being bad cause it worked flawlessly in OS 9.2.2 and jaguar and in tiger in my friends digital audio G4
im just wondering if anyone might know what could be done to fix this problem cause i know it can be fixed but i don't know where to begin or how. so i ask you how could i begin to fix this
thank you all for baring with me and reading all this. i know i wrote allot but i had to explain what was going on before i could ask for help so you could better understand what was going on. i have already updated the firmware to the latest with no change the firmware use to be the old 1.11

yea i have along time ago and also made a update to xlr8's drive database. cause i fixed the problems with the drive in OS 9.2.2 (AKA no burn support with the built in burning app or iTunes, now have full support for burning with the finder burn and iTunes thanks to a edited PioneerCDR authoring support extension that someone edited for me. found out that the Apple CD/DVD driver extension was at fault for the locking up on wake up with hdd sleep enabled that started when i installed the Pioneer drive. fixed with intech CD/DVD speedtools 6.0).
When i did the first report on the drive database on xlr8yourmac i reported what problems i was having in OS 9.2.2 and i think i reported that i had no problems in jaguar, and was trying to obtain a driver or something to try to get it to work. but to no avail at first. after i fixed the problems i did a update report
in jaguar the drive had no problems but no burn support. installed patchburn and the drive worked 100% in jag no problems what so ever. im thinking it has somthing to do with one or all of the extensions with errors but i can be wrong.
i just wonder where ryan has been on the forums in OWC's site. cause i would like to submit my crash log panic log and the extensions with errors so he could help track down the problems to see if it cant be fixed. but ive tried emailing him but no replay's. and his last reply on the OWC forums was back in desember 2005 a few day's over a year
i know it isnt the drive cause it worked flawlessly in tiger 10.4.8 on my friends Digital Audio but i know why it worked fine cause it has the proper files for the DA to work cause its a supported system. i would like to try to help to get xpostfacto to work better on the Beige G3 system
in tiger if it is something to do with xpostfacto

Beige G3 AIO with Pioneer DVR-110D not booting OS X 10.2 retail install CD

for some reason my Pioneer DVR-110D wont boot the 10.2 retail install cd's i have it will boot the OS 9.2.1 retail install cd's just fine. the only way i can boot the OS X install cd's is if i hold the command-control-power key's for 5 second's after the normal attempt to boot the cd normaly.
but during the file copying during the install it stall's out. the only way i can install OS X is if i put the orignal 24x cd-rom drive and then it will boot normaly and install normaly.
the same goes with trying to install tiger useing Xpostfacto4 but it will boot into the installer with no problem but durring the install the Pioneer will stall and will go no further during the copy prosses i can however install useing the orignal cd-rom drive
but after i get tiger installed i cant mount any disk's with either the normal cd-rom or the pioneer DVR-110D and the same goes with my other AIO i have. I dont have the disk mounting problem in OS X 10.2 or 10.2.8.
also i figured out why i was having a wake up freeze in OS 9.2.2 with the Pioneer DVR-110D there is a extention conflict happening some where with the apple cd/dvd driver extention. i disables the apple cd/dvd driver extention and rebooted amd put the system to sleep and it woke up fine but it wouldent mount any disk's cause of the extention being disabled so i rebooted and back to the wakeup freeze.
the only way to get around the wakup freeze i was having in OS 9.2.2 is to open the energy saver window and set the hdd to never fall asleep and have the monitor the only thing that sleep's and let the system idle to sleep.
sorry for the long post guy's/and gal's

From what I've read, many beiges had problems booting the 10.2 installer. I didn't have any problems booting 10.2 installer with this drive and it installed perfectly fine. However, after it installed, I couldn't actually boot into the OS, I got as far as the gray screen and it stopped and wouldn't go any further. I could boot the 10.4.3 disc as well, but as you said, the installation always stalled at "installing base system" and would go no further. I installed it by pulling my HD and hooking it up in my dad's G4, then brought it back to my computer. That worked great and 10.4.3 ran wonderfully. I just last night upgraded to 10.4.4 and it is snappy as well, however, I still have the problem with the DVR-110D. My drive will not copy large files (over 5MB) from a disc to the HD. I can mount discs and read them, but after a bit of time, it stops working entirely and won't mount discs at all. I have not tried the beta version of xpostfacto, I thought I had that version until I checked it just now. Perhaps a trip to the site to download the beta is in order. Also, the drive works great under 9.2.2, just as yours does, so I know it is not a drive error and has to be something with the Beige G3 architecture and Tiger, something is not communicating correctly. I've posed the question previously (which wasn't answered yet) about whether or not an 80 wire ATA cable would make a difference? Perhaps the 66mhz bus speed is not sufficient to have info flow from the drive to the HD? I don't know and I'm getting frustrated because I know this is a good drive! Hope we can figure it out!
Mark

Tiger and pc version of the Pioneer DVR-110D problems

ok here we go
I have tried the Beige G3 part of this forum with no luck cause i use a Beige G3 AIO
ok i have a Beige G3 AIO with a pc version of the pioneer DVR-110D running tiger 10.4.7 the drive will hardly work in tiger but will work flawlessly in 10.2 - 10.2.8, OS 9.x, windows 98, windows xp
the only way this drive will work in tiger is if i reboot with a disk in the drive and then it will work. but it will some times decide to stop working after 20 minutes or until i take out the disk.
some times it will stay working until i try to play dvd movies or try to burn with it then it will stop working and have to reboot with a disk in the drive in order to get it working again. if i don't reboot with a disk in the drive the drive will not work at all until i reboot with a disk in the drive.
im not sure if tiger is using a wrong driver for the drive or what. i know the drive is not bad cause it works so good under OS 9 and OS X 10.2 - 10.2.8. i can burn i app's under OS 9.2.2 with a modded pioneercdr authoring extension, and i can burn under OS X 10.2 - 10.2.8 with patchburn. but tiger refuses to work with the drive.
other than that tiger is running flawlessly on my Beige G3. the way it seems that its using a improper driver for the drive cause there is a apple branded version of the Pioneer DVR-110D with a modded firmware and a standard PC Pioneer DVR-110D with a pc firmware. if tiger is trying to use the drive as the apple version of the drive it can cause this cause the firmware is totally different from the standard pc version of the drive.
is there any one that can shed some light on this. maybe a driver edit or something maybe firmware to the apple version so i can try to flash this pc version to the apple firmware. or something. this drive should work as is if it works so great under OS 9.x, OS X 10.2 - 10.2.8, windows 98, and windows xp.
another problem i have is not being able to boot any OS X cd by normal means. i can get it to boot the 10.2 install cd by having the cd in the drive and hold the command option and power key's for about 5 seconds and some how the drive is tricked to boot and it does but it always fails to install cause the drive stop's working during the copy process.
the drive will boot the tiget install cd (with help from xpostfacto) without doing the trick to get OS X 10.2 install cd to boot but will still fail during the copy process. i know the fix for this is to get ahold of the apple version firmware for the DVR-110D drive. that also might fix the problem that it has under tiger. but it weird since the drive works great under OS X 10.2 - 10.2.8
sorry for making this a monster post but i would love to et this drive to work like it should under tiger like it does under the other OS's
BTW tiger is running great on the old beast besides the pioneer drive problem. not once has tiger failed to boot, not once has tiger crashed, ive timed this system on its boot time into tiger (34 seconds from start chime to full working tiger)its kinda sad to have tiger working so great but has this problem with the pioneer drive

i didnt say i used patchburn in tiger, only in jaguar did i use patchburn to gain burn support. altho i can try to use patchburn in tiger to see if it would help with the issue. AKA it seems like a driver issue to me
on how it will mount disk's when i reboot with a disk in the drive but will only halfway work. but will not mount anything if i boot without a disk in the drive when i put a disk in . but ASP in the ATA tap will show the drive . i can select disk burning in ASP only when the drive is working in its halfway state to show info. if i try when its in its non working state is will lock ASP up and some times throw tiger into a kernel panic when i try to reboot . after all that if i leave the drive alone tiger is ok

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone an i have internet and all other functions working on my computer

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone and i have internet and all other functions working on my computer

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, look under User Diagnostic Reports (not "Diagnostic and Usage Messages") for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents—the text, not a screenshot. I know the report is long. Please post all of it anyway.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

How can I get my web cam to work in Adobe Connect ?

This is actually an end user's question that I am having trouble answering to...
We use Adobe Connect to give online language classes, the end user is one of the students.
I cannot find the right Support answer to give him.
Problem:
My camera does not work when I connect to Adobe's rooms but camera works fine with other software.
Even though I suspected my old camera was working fine, yesterday I went ahead and bought a new camera.
I thought perhaps my webcam software may have been a problem, so I bought a different type camera with different software.
Even after removing all the old software, same result:
I surmised the problem might be caused by my firewall and security software, so once I tried changing the permissions for Adobe, and my Webcam, but that didn’t work.
Another time, I restarted my computer right before class and then turned off my firewall completely so there would be no interference but to no avail. I’m totally perplexed.
Isn’t there anyone else experiencing a similar problem?   Has anyone else found a solution?
I run Windows Vista with McAfee Internet Security Software. I always reboot the computer before class and open no other programs other than Google Chrome.
I now have a brand new Microsoft LifeCam Cinema Camera with LifeCam 3.5 Webcam Software.
I test my camera before going online. It always works fine.   Then I shut down the camera program and login into class.
When I “connect webcam” in the room, the light on my camera comes on (suggesting that it is ON), but only a black image is transmitted to the room.

Check to see if you have Google Voice installed. If so, remove it and see
if your problem vanishes. If not Google Voice, check to see if you have
any other communications software which interacts with your cam and
disable it. This was the problem I had with a similar problem on a Mac.
MosesJOI <[email protected]>
10/13/11 12:08 PM
Please respond to
[email protected]
To
jsb152 <[email protected]>
cc
Subject
How can I get my web cam to work in Adobe Connect ?
Re: How can I get my web cam to work in Adobe Connect ?
created by MosesJOI in General Discussion - View the full discussion
Thanks a lot Heyward for the swift reply !
I sent the advice out to the end user, but unfortunately this wasn't the
solution.
His reply is below :-
The default resolution of my new camera is already set at 640x360, but I
went ahead and tried several lower resolutions (e.g. 424x240; 320x240; and
160x120) but none worked in the room - camera still showed up as black
blank screen. Also, as far as I can tell, I don’t have the option of
adjusting the frame rate.
I started playing around with my Internet Security Settings to see if they
might be playing a role. So far, all to no avail.
Hmm...quite a tricky one - webcams always are - maybe if he can find a way
to adjust the frame rate (?).
He's going to fiddle about with the settings a bit more and see if
something does the trick.
If anyone has had a similar problem and found an ingenious solution,
please jot on a note on this thread.
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either
reply to this email or visit the message page: [
http://forums.adobe.com/message/3969561#3969561]
To unsubscribe from this thread, please visit the message page at [
http://forums.adobe.com/message/3969561#3969561]. In the Actions box on
the right, click the Stop Email Notifications link.
Start a new discussion in General Discussion by email or at Adobe Forums
For more information about maintaining your forum email notifications
please go to http://forums.adobe.com/message/2936746#2936746.

How can I get iCloud to accept my working Apple ID and password

My Apple ID and password works for iTunes and App Store. I'm trying to set up iCloud on my iPhone and iPad but i keep getting an error message that reads unsupported ID. Apple ID must be in the form of email address (@me.com). I don't have a MobileMe account. How can I get iCloud to accept my working Apple ID and password?

I've also reset my password to my Apple ID. I still get the Unsupported ID and password.

Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.

Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.

Hi deamayfield,
Thanks for visiting Apple Support Communities.
If your Music app is unresponsive, try restarting/resetting your iPhone:
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
Best,
Jeremy

I just got a new itouch and i can't get imessage or facetime to work on my home network

I just got a new itouch 4 and i can't get imessage and facetime to work on my home wifi network (Airport Express). I can't explain it. The itouch works fine otherwise uncluding the internet. Facetime and imessage work at the apple store so there must be something wrong with my home network. Please help if you can!
iPod touch, iOS 5.0.1

I changed the DNS to 8.8.8.8 as you suggested with no success, I even tried 8.8.8.8, 8.8.4.4 as suggested by others with no success either. When I try and activate iMessage or Facetime, I still get the same message "could not sign in, please check your network connection". The internet and Mail work perfectly fine on the iPod touch so the WiFi signal IS going through. I am at a loss, any other suggestions would be more than welcome. Thanks!

How can I get my excel spreadsheet to work in numbers

How can I get this budget sheet to work in numbers when it's from excel.

I couldn't get the picture of the whole thing it wouldn't load but you see where it say like 700.00 then below that it say 175.00 well that part works telling me what I need to know but when it get to where it says the 850 it stops working? it won't sum it out or something I'm not great with excel and this was sent to me by a first and it's our budget plan and I really need to be able to use it

How can I get my iPhone 5s to work in my 2015 outback

How can I get my iPhone 5s to work in my 2015 outback?

I Tried that and I can get calls out and in but no messaging.
AWindow opens and says this feature is not supported on this device
my iPhone 4 worked fine is it my iOS?

How can you get the apple tv to work in a hotel where to get on the wifi you have to still go to a website first and put in your room

How can you get the apple tv to work in a hotel where to get on the wifi you have to still go to a website first and put in your room?

Welcome to the Apple Community.
Unfortunately the Apple TV doesn't have a web browser so you can't do that.

How can I get an external microphone to work on an iphone?

How can I get an external microphone to work on an iphone?

Japib is correct.
WHAT happens? Exactly.
Also helpful would be to tell what event preceded this behavior - added App, update iOS, etc.
Quoted from  Apple's "How to write a good question"
To help other members answer your question, give as many details as you can.
Include your product name and specs such as processor speed, memory, and storage capacity. Please do not include your Serial Number, IMEI, MEID, or other personal information.
Provide the version numbers of your operating system and relevant applications, for example "iOS 6.0.3" or "iPhoto 9.1.2".
Describe the problem, and include any details about what seems to cause it.
List any troubleshooting steps you've already tried, or temporary fixes you've discovered.
ÇÇÇ

Hi, Im trying to install the CC installer on my new MacPro. When the installer loads it says there's a "Download Error" and can't get beyond that. Everything work fine on my old Mac. Any Ideas?

Im trying to install the CC installer on my new MacPro. When the installer loads it says there's a "Download Error" and can't get beyond that. Everything work fine on my old Mac. Any Ideas?

Chasel please see Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html for information on how to resolve download errors.

Can't get Pioneer DVR-110D to work

Similar Messages

Maybe you are looking for