Can't get router working after switching from DSL to Cable broadband???
I have a WRT54G v.5
I just switched from dsl service to cable broadband. I can't get my router to work. I hooked it back up just as the dsl modem used to be. there is an ethernet cable that goes from the cable modem to the router. then an eithernet cable that goes from the router to the computer. this does not work. If I just take the router out of the loop and run an eithernet cable straight from the cable modem to the computer it works fine. so the cable internet service is working fine up to the modem. The router is the problem. I have restarted both the computer and the router. so that rules that out. can you help me?
Open the setup page of the router by launching an Internet Explorer Browser and type the address bar, 192.168.1.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as admin and click on ok.On the main setup page the ""Internet Connection Type"" should be on ""Obtain IP Automatically - DHCP “. Click on the Save Settings button.Now click on the sub tab ""MAC address clone"".- Click on enable.Click Clone & click save settings
Check WAN Ip on Status page of router .... If getting Valid Ip .... try going online...If not ... power cycle for 4-5 minutes & then, try going online.
Similar Messages
-
Can't access PIX 501 after switch from dsl to cable
Hi--
I have two small offices and recently switched from dsl to cable internet. the two pix501 f/w units worked fine on dsl, but for the life of me I cannot even access the units now from the inside as I was able to do before when on dsl signal. I know I need to change the configuration from PPPoe to DHCP, but I can't get access to do it.
Any suggestions?
I believe I have 6.2 software, but I'm not sure. The Inside address is 10.8.6.1 now.
thanks--jbJorge--
I did have the Pix connected to router, 192 168.1.1 for convenience, so I could still get internet wirelessly without having to do lots of wire unplugging and plugging.
I have since changed to topology of comcast modem connected directly to pix which in turn connects directly to laptop.
In this configuration, laptop pings 10.8.6.1 ok, but pix has no connectivity to comcast.
When laptop connected directly to comcast modem,(ie pix removed) the ipconfig /all from laptop reads the following from comcast:
ip 71.192.7.130
mask 255.255.252.0
DG 72.192.11.1
DHCP server 68 87 71 52
DNS 68 87 71 226 and 68 87 73 242
Response to pix# show route | inc 0.0.0.0 is nothing.
For reference, here is show run
pixMDC# show run
: Saved
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password PVSASRJovmamnVkD encrypted
passwd PVSASRJovmamnVkD encrypted
hostname pixMDC
domain-name keene.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list outside_access_in permit icmp any any echo-reply
access-list outside_access_in permit icmp any any source-quench
access-list outside_access_in permit icmp any any unreachable
access-list outside_access_in permit icmp any any time-exceeded
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute
ip address inside 10.8.6.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm location 10.0.0.0 255.0.0.0 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 10.8.6.0 255.255.255.0 0 0
access-group outside_access_in in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 10.0.0.0 255.0.0.0 inside
http 10.8.6.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet 10.8.6.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 10.8.6.2-10.8.6.33 inside
dhcpd dns 151.203.0.84 151.202.0.84
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
vpnclient server 10.8.6.0 10.0.0.0
vpnclient mode client-mode
vpnclient vpngroup fnd password ********
vpnclient username fnd password ********
vpnclient enable
terminal width 80
Cryptochecksum:6ca15e834dc867c6f12b46b2bd28a4a8
: end
pixMDC#
pixMDC#
pixMDC#
pixMDC# ping 71.192.7.130
No route to host 71.192.7.130.
Usage: ping [if_name]
pixMDC#
It appears that the pix is not seeing the comcast dhcp signal and latching onto it.
Thanks,
Jeffrey -
Switched from DSL to CABLE. WRT54G Wireless Router stopped working.
When I switched from DSL to CABLE, my WRT54G Wireless Router stopped working. I am not able to access the router page (192.168.1.1) Also, when I use the set up CD for re-installation, the wizard aborts in the middle saying it can not connect.
I appreciate any help to resolve this problem.
P.S. The router acts like a one-port wired router.Here is my favorite method for resetting a router to factory defaults, and trying to get it working again.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you. -
IPhone 4s Voice mail notification not working after switching from Verizon to PagePlus.
iPhone 4s Voice mail notification not working after switching from Verizon to PagePlus. How can I get the notifications working?
Contact your carrier - voicemail, and visual voicemail, is a carrier feature.
-
Switched from DSL to cable and now can't find apple tv in itunesdevice list
I just switched from DSL to Cable and now for whatever reason I cannot find my apple tv in the itunes device list on my desktop computer. If I use another laptop through the same wireless router I can see the apple tv no problem. My apple tv can see my wireless router and connect to the internet and watch youtube/trailers/etc.
I have tried restoring the apple tv, and have also tried uninstalling and reinstalling the itunes on the desktop. I also reset the wireless router...none of the above seem to work. any suggestions would be greatly appreciated as this has been crazy frustrating...thanks in advance.If you have an AirPort Extreme or a Time Capsule, you need to use the AirPort utility to access it. Otherwise, your router has a control panel that you can access by entering the router's IP address into your web browser. You'll have to check your router's documentation for the default login name and password, but it's often admin admin or root root (which is why you should at least change the password as soon as possible).
-
Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????
Hmmmm.
If you reset the AirPort Extreme by holding in the reset button for 9-10 seconds and then releasing, the AirPort should be back in default settings which would allow mutliple computers to connect to the LAN ports on the AirPort.
Power off the cable modem for now and leave it off at least 15 minutes.
With the AirPort Extreme still powered on, hold in the rest button on the back for 9-10 seconds and release. Allow a full minute for the AirPort Extreme to restart to a slow, blinking abmer light.
Then, power off the AirPort Extreme.
Check to make sure that the Ethernet cable from the modem is connected to the WAN "O" port on the AirPort Extreme.
After the modem has been powered off for at least 15 minutes, power it up and let it run for 5 minutes by itself.
Now, power up the AirPort Exteme and let it run for 2-3 minutes
Open Macintosh HD > Applications > Utilities > AirPort Utility
Connect an Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Express
Click on the AirPort Exteme, then click Continue to follow the guided setup tp configure the AirPort Extreme. You can use the same wireless network name, password, etc that you used before, or set up a new name and password, etc. -
Switched from DSL to cable, need help getting TC back on line.
I just switched from dsl to a cable modem to access the internet and my service provider doesn't offer support for my TC. Where can I find out how to change my settings (I guess from PPPOE to DHCP) to allow internet access from my wireless network? It seems like a matter of plugging the right numbers into the right place but I don't know where to find the numbers or where to put them exactly. Any help is appreciated.
Hello Sivad72. Welcome to the Apple Discussions!
I suggest that you first perform a "hard" reset on your Time Capsule (TC). Then, perform a complete power recycle of your network components to get them "talking" again.
Power Recycling Steps
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
o Power-off the modem, TC, & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the TC; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset." -
Computer won't CONNECT to c4480 after move from DSL to cable
I have a Photosmart C4480 operating under Windows 7 Home Premium 64bit
It worked fine I could print/scan and read and write to a card
I moved so disconneted it packed it. When I got to the new place set up the computer
hooked up the USB cable and connected it between the printer and the computer.
When I tried to print nothing happened. I Opened Windows Explored and discoverd
that the computer could not see the printer I checked the cable thats Ok tried reinstalling drivers
when it finished it said "connect USB cable" meaning that it could not see the printer.
Other than that there were no error messages
The only thing that changed was at the old location I was using DSL now I am on cable
Do I need a new printer?
This question was solved.
View Solution.BAC0296, if I understand your issue correctly, you recently moved and now your USB connected printer is no longer recognized by the computer. Is this correct? If so, don't worry about moving from DSL to cable, it shouldn't effect a USB connection.
To start, I would unplug the USB cable from the printer and the computer. Then go to your Devices and Printers folder and delete the copies of the printer there. We're going to start fresh from here.
Once they are all removed, go to your start menu and then to All Programs and find the "HP" folder. In that folder there shold be another folder for your c4480. In that folder there should be an item listed for the printer setup and installation. Go through this process and when you are prompted plug the USB cable into the printer and the comptuer. Finish the installation from here.
Let me know if this helps! -
[solved] couldn't get NX work after switching to 64 bit system
I switched the system to 64 bit with my "home" folder untouched. Then I couldn't get NX work. Here is the detailed output:
NX> 203 NXSSH running with pid: 4866
NX> 285 Enabling check on switch command
NX> 285 Enabling skip of SSH config files
NX> 285 Setting the preferred NX options
NX> 200 Connected to address: xxx.xx.xxx.xxx on port: 22
NX> 202 Authenticating user: nx
NX> 208 Using auth method: publickey
HELLO NXSERVER - Version 3.2.0-73 OS (GPL, using backend: 3.4.0)
NX> 105 hello NXCLIENT - Version 3.2.0
NX> 134 Accepted protocol: 3.2.0
NX> 105 SET SHELL_MODE SHELL
NX> 105 SET AUTH_MODE PASSWORD
NX> 105 login
NX> 101 User: horse
NX> 102 Password:
NX> 103 Welcome to: office user: horse
NX> 105 listsession --user="horse" --status="suspended,running" --geometry="1400x1050x24+render" --type="unix-gnome"
NX> 127 Sessions list of user 'horse' for reconnect:
Display Type Session ID Options Depth Screen Status Session Name
NX> 148 Server capacity: not reached for user: horse
NX> 105 startsession --link="wan" --backingstore="1" --encryption="1" --cache="16M" --images="64M" --shmem="1" --shpix="1" --strict="0" --composite="1" --media="0" --session="work" --type="unix-gnome" --geometry="1400x1030" --client="linux" --keyboard="pc102/us" --screeninfo="1400x1030x24+render"
NX> 1000 NXNODE - Version 3.2.0-73 OS (GPL, using backend: 3.4.0)
NX> 700 Session id: office-1000-593D8F5A1C9C4FC7C01CA605A678F07D
NX> 705 Session display: 1000
NX> 703 Session type: unix-gnome
NX> 701 Proxy cookie: b3fb6908954b810ed8535b0deb2ff786
NX> 702 Proxy IP: 127.0.0.1
NX> 706 Agent cookie: b3fb6908954b810ed8535b0deb2ff786
NX> 704 Session cache: unix-gnome
NX> 707 SSL tunneling: 1
/opt/NX/bin/nxagent: error while loading shared libraries: libXcomp.so.3: cannot open shared object file: No such file or directory
/opt/NX/bin/nxserver: line 1531: 8001 Terminated sleep $AGENT_STARTUP_TIMEOUT
NX> 105 NX> 596 Session startup failed.
NX> 1004 Error: NX Agent exited with exit status 1. To troubleshoot set SESSION_LOG_CLEAN=0 in node.conf and investigate "/home/horse/.nx/F-C-office-1000-593D8F5A1C9C4FC7C01CA605A678F07D/session". You might also want to try: ssh -X myserver; /opt/NX/bin/nxnode --agent to test the basic functionality. Session log follows:
Can't open /opt/NX/var/db/running/sessionId{593D8F5A1C9C4FC7C01CA605A678F07D}: No such file or directory.
mv: cannot stat `/opt/NX/var/db/running/sessionId{593D8F5A1C9C4FC7C01CA605A678F07D}': No such file or directory
NX> 1006 Session status: closed
NX> 280 Exiting on signal: 15
I guess there are two problems with it:
1. It couldn't resume. (in fact I want to start a new session. I don't know where are the old session information: I already removed all related file in the home folder.)
2. the error with "nxagent". It says it couldn't load libXcomp.so.3. I don't know how to install it.
Any help will be appreciated.. Thanks!
Last edited by horsecool (2010-12-28 17:53:36)Thanks for your reply! I do have Xorg installed. And The X works fine on the local computer (not remote login).
Here is the result from "locate libXcomp":
$ locate libXcomp
/opt/NX/lib/libXcompext.so
/opt/NX/lib/libXcompext.so.1
/opt/NX/lib/libXcompext.so.3
/opt/NX/lib/libXcompext.so.3.4.0
/opt/NX/lib/libXcompsh.so
/opt/NX/lib/libXcompsh.so.3
/opt/NX/lib/libXcompsh.so.3.4.0
/opt/NX/lib/libXcompshad.so
/opt/NX/lib/libXcompshad.so.3
/opt/NX/lib/libXcompshad.so.3.4.0
/usr/lib/libXcomposite.so
/usr/lib/libXcomposite.so.1
/usr/lib/libXcomposite.so.1.0.0 -
Switched from DSL to Cable, Can't connect to the internet
After switching to cable modem (Motorola SB5120 SURFboard) from DSL, I can't connect to the internet using my airport express. Everything is green - modem and airport, and the signal on my computer looks like I have full access, but there is a scrolling message... looking for PPPoe host. I have unplugged everything and restarted per the instructions on this site, but get the same result every time. My computer connects just fine using direct connection to the modem. I saw a download for a firm ware update for the express, but don't know how to apply that, either. Any help out there?
Thanks!Hello mom2gr82. Welcome to the Apple Discussions!
Let's double-check your AirPort Express Base Station's (AX) settings...
AirPort Express Base Station Setup (AX) w/High-Speed Cable Modem
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
Modem/Router Power ReCycling
o Power-off the Cable modem, AX, & computer(s); Wait at least 30 minutes.
o Power-on the Cable modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
Setup the AX
Connect to the AX's wireless network, and then, using the AirPort Admin Utility, try these settings:
AirPort tab
o Base Station Name: <whatever you wish or use the default>
o AirPort Network Name: <whatever you wish or use the default>
o Create a closed network (unchecked)
o Wireless Security: Not enabled
o Channel: Automatic
o Mode: 802.11b/g Compatible
Internet tab
o Connect Using: Ethernet
o Configure: Using DHCP
o WAN Ethernet Port: Automatic
Network tab
o Distribute IP addresses (checked)
o Share a single IP address (using DHCP & NAT) (enabled)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
Change Wireless Security
o Wireless Security: WPA Personal or WPA2 Personal
o Encryption Type: WPA and WPA2
Base Station Options - WAN Ethernet Port
o Enable Ethernet Port (checked)
o Enable SNMP Access (unchecked)
o Enable Remote Configuration (unchecked)
o Enable Remote Printer Access (unchecked) -
Switched from DSL to cable, can't connect through Airport Extreme.
Network help required!! I switched from my spotty, poor DSL hookup this afternoon, to a new faster cable hookup. I have 5 devices to attach through an airport extreme. All 5, ( 2 iMacs 1 iPhone 1 iPad all wireless 1 XBox wired ) on dsl, hooked up this morning, now on cable, only 1 at a time. And only after restarting the cable modem. The only part of my network that changed is the isp...thoughts?
I have the cable to the modem, ethernet to AE, wireless signal to iDevices, ethernet to XBox.Follow the expert instructions in this User Tip provided by forum guru Tesserax:
AirPort - Complete Power Recycle -
Switching From DSL to Cable Modem
I am about to switch from a DSL service to a faster Cable Modem service using my local provider's (Time Warner Roadrunner) self install kit. I was hoping that you experts could give me some advice before I begin the conversion.
Currently, my DSL modem connects to Airport Extreme, then Airport Extreme to my iMAC.
My question is whether to first plug in the ethernet cable from the new cable modem directly into the iMAC and make sure that the internet is accessible. Then power off all devices, hook up Airport Extreme back into the chain and try again.
Or right from the start, should I just plug the new cable modem into Airport Extreme and see if the iMAC sees the internet automatically?
Any step by step advise would be appreciated.
KranepoolMy question is whether to first plug in the ethernet cable from the new cable modem directly into the iMAC and make sure that the internet is accessible. Then power off all devices, hook up Airport Extreme back into the chain and try again.
You pretty much summed it up.
I would do the following in order:
o Power down the DSL modem, AirPort Extreme Base Station (AEBS), and iMac. Order is not critical.
o Install the new cable modem and connect the iMac directly to it using an Ethernet cable.
o Power-on the cable modem; wait at least 10-15 minutes.
o Power-on the iMac, and then, check for Internet connectivity.
o Power down the iMac, and then, the cable modem.
o Disconnect the iMac from the modem; connect an Ethernet cable between the modem and the WAN port of the AEBS; connect another Ethernet cable between the LAN port of the AEBS and the iMac.
o Power-on the cable modem; wait at least 10-15 minutes.
o Power-on the AEBS; wait at least 5 minutes.
o Power-on the iMac, and then, check for Internet connectivity. -
Can't get GDM to work after switch from KDE/KDM to Gnome/GDM
When I start up it boots into GDM but goes to failsafe with a single terminal and that is it. I would then go to init 3 and startx from there. Goes to Gnome. I open a terminal and use gdmsetup and get that another login manager is starting a boot up. I changed .xinitrc and inittab to point to gnome and gdm but nothing. What am I missing. KDE is uninstalled, is it possible the kdm didn't uninstall.
help pleaseadd @gdm to your daemons list
-
Trackpoint does not work after switching from the tablet to laptop mode.
I use my tablet to run a smartboard. Sometimes when I switch to the tablet mode and back by reversing the display, the trackpoint and mouse keys stop working. The touchpad below it still works. I am running windows 7. I have gone into the control panel, under mouse, and both the trackpoint and touchpad are still both checked. ?? When I restart the functions return.
Hi Remaxjoe,
Welcome to Lenovo Community Forums!
I’m really sorry to hear that trackpoint is not working properly in your Lenovo system.
I would suggest you to download the Ultranav drivers for your system and install it.
Below is the link to enter downloads page and install the Ultranav driver.
• Support Drivers & Software downloads
Please click on "QUICK PATH”, enter your system model and select the exact model depending on the MTM number of your device.
Spoiler (Highlight to read)
You can refer here for further information.
Hope this helps!
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter! -
Stolen 4s returned but can't get it working after reset
My fone was solen in November and returned by the police yesterday. The thief had changed all setting and named the fone as his. I had it on FIND MY FONE but no luck but yesterday it deleted it. The screen is black with the circle icon going round . When I turn it off and back on it shows Apple badge for a bit then home screen , slide to unlock then back to the circle going round and round . It also said sim is locked and i cant unlocknit quick enough before black sreen again.Please help
You need to force the phone into recovery mode & restore it, as described here:
http://support.apple.com/kb/ht1212
You can't just connect to iTunes as Eric's post tells you, that won't work.
Maybe you are looking for
-
How can I wipe my hard drive and clean install Mountain Lion?
Hi I have a 21.5 inch mid 2011 iMac running Mountain Lion, I want to wipe my hard drive and clean install Mountain Lion. I dont want all my stuff back, just photos and music, the rest I'll reinstall my self. I also dont have a exteranl harddrive. onl
-
I upgraged my macbook 2.4 GHz ram to 4g and now lower slot shows empty
I have recently upgraged my ram to 4g and now the lower memory slot always shows empty. Any suggestions?
-
Due to Upper() query not using Indexes.......
Hi, I have query as under: SELECT max(A.REGION_ID) FROM SOP_REGION_COUNTRY_MAP A, SOP_REGION_PRODLINE_MAP B, SOP_REGION_ACTIVITY_MAP C WHERE A.REGION_ID = B.REGION_ID AND A.REGION_ID = C.REGION_ID AND upper(trim(COUNTRY_NAME))
-
Portege series, different battery life on R100 and M100?
Hello everybody, I want to buy a new notebook with high battery life for mobile working. The R100 and M100 are shortlisted, but does anybody know if there are differences in battery life. I have tested the two NBs at my dealer, but I have no experien
-
Problems passing std::vector char by reference
I'm currently developing an InDesign Server plug-in off the CS5 SDK (Build 335). I've written some code that attempts to return the image bytes of a JPEG via a function bool CJPEGImage::Copy( std::vector<char>& Data ); The typical usage is...