Can't get viewing card to work! Sky Sports. 'VCN i...
Card arrived tuesday, but doesn't seem to work.....inserted right way up, in slot for over an hour on Sky sports channel, tried to activate online.... Keeps saying 'VCN is not the current card for support' .... Pls help as am really fed up now.
What does this mean & can anyone advise me?
Many thanks.
Hi TheChairman,
Strange, could you email in your account details and forum username and I'll take a look at this?
The email address is my profile, on my username to see it
Thanks,
Stephanie
Stephanie
BTCare Community Manager
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post. If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
Similar Messages
-
I bought a Rosewill RC-200 raid card and can't get windows to instal to it with 2 x 80 gb drives RAID 0. In the BIOS, it doesn't show up in the "Standard CMOS Features" list, which I guess might make sense, but it does show up in the Hard Disk Boot Priority list. It lists 2 hard drives, SCSI-1: MAXTOR 6B080P0 AND SCSI-0: WDC WD800JB-00CRA1, and "Bootable Add-in Cards. If I boot to the Windows CD, neither of the drives or the RAID show up. I booted with and without the RAID 0 setup and no drives were available to install to. How can I get windows installed on this RAID?
Thanks
Joe McDaniel
System specs:
K8N Neo4 mobo w/ AMD 4600+Quote from: Joe Mac on 02-September-07, 18:03:10
Now here is the problem I am faced with. When I boot, it says "Disk Boot Failure insert system disk and press enter". If I insert the install cd it will boot Windows normally. If I boot without the CD it gives me the error. Any thoughts? I have XP installed on the RAID card. I have the boot sequence setup as Hard drive then CD and the Boot disk priority to the SCSI-0 Sil Striped Set <PM> first. Is there some other BIOS bit I'm missing?
Thanks
Joe Mac
It looks like that there is not active partition on the drive.
boot from XP CD, then go to recovery console.
use "fixmbr" to re-write MBR on the HDD.
then apply active partition with "diskpart"
type:
diskpart [ENTER]
select disk 0 [ENTER]
list partition [ENTER] /* locate your bootable parition and remember his number, usually its 1st listed, also "Type" of it listed should be "Primary" */
select partition 1 [ENTER]
active [ENTER]
exit [ENTER]
reboot PC, to reflect changes. -
Ok, I am actually having troubles with my itunes music card. I accidentally scratched off a letter. how can i get my card to work without the actual code? thank you.
Yu can try contacting iTunes. See the iTunes Cards abd Code topic of:
Apple - Support - iTunes -
Hardware missing -AGP Graphics card. How can I get my FCE 4 working on the new computer? Cheers
Hi I have just upgraded my computer to Mac OSX 10.6.7 now I cant open my FCE 4. Message reads, Hardware missing -AGP Graphics card. How can I get my FCE 4 working on the new computer? Cheers
Thanks, just so I know we are talking about the same items please let me know - When you say "run Prokit" do you mean downloaded? Which I did. I dont have Prokit 4.0.1 if you are referring to that, do I need this first? Please explain what application name I am looking for if other than Prokit which is sitting in my "download folder" do I need to manually put it into the apps folder? Sorry if the questions are layman but this area is not a very strong point for me. Thanks for your help so far.
-
Can't get direct rendering to work
On my notebook with an Intel 945GM card, I can't get direct rendering to work.
I'm using the 'xf86-video-intel' driver.
/etc/X11/xorg.conf:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Touchpad" "AlwaysCore SendCoreEvents"
# InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "DontZap"
Option "DontZoom"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "xtrap"
Load "extmod"
Load "GLcore"
Load "record"
Load "dbe"
Load "glx"
Load "dri"
Load "freetype"
Load "synaptics"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "InputDevice"
Driver "synaptics"
Identifier "Touchpad"
Option "Device" "/dev/psaux"
Option "Protocol" "auto-dev"
Option "LeftEdge" "1700"
Option "RightEdge" "5300"
Option "TopEdge" "1700"
Option "BottomEdge" "4200"
Option "FingerLow" "25"
Option "FingerHigh" "30"
Option "MaxTapTime" "180"
Option "MaxTapMove" "220"
Option "VertScrollDelta" "100"
Option "MinSpeed" "0.06"
Option "MaxSpeed" "0.12"
Option "AccelFactor" "0.0010"
Option "SHMConfig" "on"
# Option "Repeater" "/dev/ps2mouse"
EndSection
Section "Monitor"
#DisplaySize 330 210 # mm
DisplaySize 338 211
Identifier "Monitor0"
VendorName "AUO"
ModelName "2174"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "ColorKey" # <i>
#Option "CacheLines" # <i>
#Option "Dac6Bit" # [<bool>]
#Option "DRI" # [<bool>]
#Option "NoDDC" # [<bool>]
#Option "ShowCache" # [<bool>]
#Option "XvMCSurfaces" # <i>
#Option "PageFlip" # [<bool>]
Identifier "Card0"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
BusID "PCI:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1280x800" "1152x864" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1280x800" "1152x864" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x800" "1152x864" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
And here is /var/log/Xorg.0.log:
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.4.0.90
Release Date: 5 September 2007
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-ARCH i686
Current Operating System: Linux zg6y3zg9f3x 2.6.24.3-ARCH #2 SMP PREEMPT Sun Mar 2 23:22:11 CET 2008 i686
Build Date: 03 February 2008 02:54:48PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Mar 3 00:20:16 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Touchpad"
(**) |-->Input Device "Keyboard0"
(**) Option "DontZap"
(**) Option "DontZoom"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(==) Including the default font path /usr/share/fonts/misc,/usr/share/fonts/100dpi:unscaled,/usr/share/fonts/75dpi:unscaled,/usr/share/fonts/TTF,/usr/share/fonts/Type1.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(==) |-->Input Device "Mouse0"
(==) The core pointer device wasn't specified explicitly in the layout.
Using the first mouse device.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81d65c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 2.0
X.Org XInput driver : 2.0
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(--) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,27a0 card 1025,0090 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:02:0: chip 8086,27a2 card 1025,0090 rev 03 class 03,00,00 hdr 80
(II) PCI: 00:02:1: chip 8086,27a6 card 1025,0090 rev 03 class 03,80,00 hdr 80
(II) PCI: 00:1b:0: chip 8086,27d8 card 1025,0090 rev 02 class 04,03,00 hdr 00
(II) PCI: 00:1c:0: chip 8086,27d0 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:1: chip 8086,27d2 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:2: chip 8086,27d4 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:3: chip 8086,27d6 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1d:0: chip 8086,27c8 card 1025,0090 rev 02 class 0c,03,00 hdr 80
(II) PCI: 00:1d:1: chip 8086,27c9 card 1025,0090 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:2: chip 8086,27ca card 1025,0090 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:3: chip 8086,27cb card 1025,0090 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:7: chip 8086,27cc card 1025,0090 rev 02 class 0c,03,20 hdr 00
(II) PCI: 00:1e:0: chip 8086,2448 card 0000,0000 rev e2 class 06,04,01 hdr 01
(II) PCI: 00:1f:0: chip 8086,27b9 card 1025,0090 rev 02 class 06,01,00 hdr 80
(II) PCI: 00:1f:2: chip 8086,27c4 card 1025,0090 rev 02 class 01,01,80 hdr 00
(II) PCI: 00:1f:3: chip 8086,27da card 1025,0090 rev 02 class 0c,05,00 hdr 00
(II) PCI: 05:00:0: chip 8086,4222 card 8086,1000 rev 02 class 02,80,00 hdr 00
(II) PCI: 06:01:0: chip 14e4,170c card 1025,0090 rev 02 class 02,00,00 hdr 00
(II) PCI: 06:04:0: chip 1524,1412 card 1400,0000 rev 10 class 06,07,00 hdr 82
(II) PCI: 06:04:1: chip 1524,0530 card 1025,0090 rev 01 class 05,01,00 hdr 80
(II) PCI: 06:04:2: chip 1524,0550 card 1025,0090 rev 01 class 08,05,01 hdr 80
(II) PCI: 06:04:3: chip 1524,0520 card 1025,0090 rev 01 class 05,01,00 hdr 80
(II) PCI: 06:04:4: chip 1524,0551 card 1025,0090 rev 01 class 05,01,00 hdr 80
(II) PCI: End of PCI scan
(II) Intel Bridge workaround enabled
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,7), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:28:0), (0,2,2), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 3: bridge is at (0:28:1), (0,3,3), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 4: bridge is at (0:28:2), (0,4,4), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 5: bridge is at (0:28:3), (0,5,5), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 5 non-prefetchable memory range:
[0] -1 0 0xd0100000 - 0xd01fffff (0x100000) MX[b]
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 6: bridge is at (0:30:0), (0,6,7), BCTRL: 0x0000 (VGA_EN is cleared)
(II) Bus 6 non-prefetchable memory range:
[0] -1 0 0xd0000000 - 0xd00fffff (0x100000) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:31:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-CardBus bridge:
(II) Bus 7: bridge is at (6:4:0), (6,7,10), BCTRL: 0x0740 (VGA_EN is cleared)
(--) PCI:*(0:2:0) Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xd0200000/19, 0xc0000000/28, 0xd0300000/18, I/O @ 0x5088/3
(--) PCI: (0:2:1) Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xd0280000/19
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) Active PCI resource ranges:
[0] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[1] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[2] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[3] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[4] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[5] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[6] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[7] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[8] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[9] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[10] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[11] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[12] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[13] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[14] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[15] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[16] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[17] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[18] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) Inactive PCI resource ranges:
[0] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[1] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[2] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[3] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[1] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[2] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[3] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[4] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[5] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[6] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[7] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[8] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[9] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[10] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[11] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[12] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[13] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[14] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[15] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[16] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[17] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[18] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) Inactive PCI resource ranges after removing overlaps:
[0] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[1] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[2] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[3] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[5] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[6] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[7] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[8] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[9] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[10] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[11] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[12] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[13] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[14] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[15] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[18] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[19] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[20] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[22] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[23] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[24] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[25] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[26] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[27] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[28] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "xtrap"
(II) Loading /usr/lib/xorg/modules/extensions//libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DEC-XTRAP
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.4.0.90, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 4.3.99.902, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 2.2.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "synaptics"
(II) Reloading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
965GM, 965GME/GLE, G33, Q35, Q33, Intel Integrated Graphics Device
(II) Primary Device is: PCI 00:02:0
(WW) intel: No matching Device section for instance (BusID PCI:0:2:1) found
(--) Chipset 945GM found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[5] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[6] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[7] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[8] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[9] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[10] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[11] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[12] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[13] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[14] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[15] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[18] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[19] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[20] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[22] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[23] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[24] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[25] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[26] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[27] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[28] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[5] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[6] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[7] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[8] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[9] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[10] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[11] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[12] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[13] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[14] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[15] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[16] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[19] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[20] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[21] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[22] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[23] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[24] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[25] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[26] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[27] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[28] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[29] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[30] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[31] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
[32] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[33] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.1.0
ABI class: X.Org Video Driver, version 2.0
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 0.1.0
ABI class: X.Org Video Driver, version 2.0
(**) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 945GM
(--) intel(0): Chipset: "945GM"
(--) intel(0): Linear framebuffer at 0xC0000000
(--) intel(0): IO registers at addr 0xD0200000
(II) intel(0): 2 display pipes available.
(==) intel(0): Using EXA for acceleration
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"(II) Module "i2c" already built-in
(II) intel(0): Output VGA using monitor section Monitor0
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): EDID vendor "AUO", prod id 8564
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) intel(0): initializing int10
(WW) intel(0): Bad V_BIOS checksum
(II) intel(0): Primary V_BIOS segment is: 0xc000
(II) intel(0): VESA BIOS detected
(II) intel(0): VESA VBE Version 3.0
(II) intel(0): VESA VBE Total Mem: 7872 kB
(II) intel(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip Accelerated VGA BIOS
(II) intel(0): VESA VBE OEM Software Rev: 1.0
(II) intel(0): VESA VBE OEM Vendor: Intel Corporation
(II) intel(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics Controller
(II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(0): Output TV has no monitor section
(II) intel(0): EDID vendor "AUO", prod id 8564
(II) intel(0): Output VGA disconnected
(II) intel(0): Output LVDS connected
(II) intel(0): Output TV disconnected
(II) intel(0): Output LVDS using initial mode 1280x800
(II) intel(0): Monitoring connected displays enabled
(II) intel(0): detected 256 kB GTT.
(II) intel(0): detected 7932 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Will not try to enable page flipping
(==) intel(0): Triple buffering disabled
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(**) intel(0): Display dimensions: (338, 211) mm
(**) intel(0): DPI set to (96, 154)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 2.2.0
ABI class: X.Org Video Driver, version 2.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module "ramdac" already built-in
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to 0xd000000a
(WW) intel(0): PP_STATUS before: on, ready, sequencing idle
(WW) intel(0): PP_STATUS after: on, ready, sequencing on
(WW) intel(0): Register 0x68080 (TV_FILTER_CTL_1) changed from 0x8000085e to 0x800010bb
(WW) intel(0): Register 0x68084 (TV_FILTER_CTL_2) changed from 0x00012d2d to 0x00028283
(WW) intel(0): Register 0x68088 (TV_FILTER_CTL_3) changed from 0x00009696 to 0x00014141
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xd0300000 - 0xd033ffff (0x40000) MS[b]
[1] 0 0 0xc0000000 - 0xcfffffff (0x10000000) MS[b]
[2] 0 0 0xd0200000 - 0xd027ffff (0x80000) MS[b]
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[7] -1 0 0xd0000000 - 0xd0001fff (0x2000) MX[b]
[8] -1 0 0xd0100000 - 0xd0100fff (0x1000) MX[b]
[9] -1 0 0xd0544000 - 0xd05443ff (0x400) MX[b]
[10] -1 0 0xd0340000 - 0xd0343fff (0x4000) MX[b]
[11] -1 0 0xd0280000 - 0xd02fffff (0x80000) MX[b](B)
[12] -1 0 0xd0300000 - 0xd033ffff (0x40000) MX[b](B)
[13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[b](B)
[14] -1 0 0xd0200000 - 0xd027ffff (0x80000) MX[b](B)
[15] -1 0 0xd0003100 - 0xd00031ff (0x100) MX[b]
[16] -1 0 0xd0003800 - 0xd000387f (0x80) MX[b]
[17] -1 0 0xd0003400 - 0xd00034ff (0x100) MX[b]
[18] -1 0 0xd0003000 - 0xd000307f (0x80) MX[b]
[19] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprD)
[20] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprD)
[21] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprD)
[22] 0 0 0x00005088 - 0x0000508f (0x8) IS[b]
[23] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[24] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[25] -1 0 0x00005420 - 0x0000543f (0x20) IX[b]
[26] -1 0 0x00005440 - 0x0000544f (0x10) IX[b]
[27] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[28] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[29] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[30] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[31] -1 0 0x00005400 - 0x0000541f (0x20) IX[b]
[32] -1 0 0x000050e0 - 0x000050ff (0x20) IX[b]
[33] -1 0 0x000050c0 - 0x000050df (0x20) IX[b]
[34] -1 0 0x000050a0 - 0x000050bf (0x20) IX[b]
[35] -1 0 0x00005088 - 0x0000508f (0x8) IX[b](B)
[36] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[37] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) intel(0): Kernel reported 488960 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 1955836 kB available
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
[drm] failed to load kernel module "i915"
(EE) [drm] drmOpen failed.
(EE) intel(0): [dri] DRIScreenInit failed. Disabling DRI.
(==) intel(0): VideoRam: 262144 KB
(**) intel(0): Framebuffer compression enabled
(**) intel(0): Tiling enabled
(II) intel(0): adjusting plane->pipe mappings to allow for framebuffer compression
(II) intel(0): Page Flipping disabled
(==) intel(0): Write-combining range (0xc0000000,0x10000000)
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) EXA(0): Offscreen pixmap area of 19660800 bytes
(II) EXA(0): Driver registered support for the following operations:
(II) Solid
(II) Copy
(II) Composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x007bf000 (pgoffset 1983)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x00c80000 (pgoffset 3200)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB)
(II) intel(0): 0x00020000-0x0061ffff: compressed frame buffer (6144 kB, 0x000000007f820000 physical
(II) intel(0): 0x00620000-0x00620fff: compressed ll buffer (4 kB, 0x000000007fe20000 physical
(II) intel(0): 0x00621000-0x0062afff: HW cursors (40 kB, 0x000000007fe21000 physical
(II) intel(0): 0x0062b000-0x00632fff: logical 3D context (32 kB)
(II) intel(0): 0x00633000-0x00633fff: overlay registers (4 kB, 0x000000007fe33000 physical
(II) intel(0): 0x00640000-0x00c7ffff: front buffer (6400 kB)
(II) intel(0): 0x007bf000: end of stolen memory
(II) intel(0): 0x00c80000-0x01f3ffff: exa offscreen (19200 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is off
(II) intel(0): Display plane B is now disabled and connected to pipe A.
(II) intel(0): Pipe B is on
(II) intel(0): Display plane A is now enabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output LVDS is connected to pipe B
(II) intel(0): Output TV is connected to pipe none
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): Set up textured video
(II) intel(0): Set up overlay video
(II) intel(0): direct rendering: Failed
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) AIGLX: Screen 0 is not DRI capable
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/xorg/modules/extensions//libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) GLX: Initialized MESA-PROXY GL provider for screen 0
(II) intel(0): Setting screen physical size to 331 x 207
(II) Synaptics touchpad driver version 0.14.6 (1406)
(--) Touchpad auto-dev sets device to /dev/input/event5
(**) Option "Device" "/dev/input/event5"
(**) Option "SHMConfig" "on"
(**) Option "LeftEdge" "1700"
(**) Option "RightEdge" "5300"
(**) Option "TopEdge" "1700"
(**) Option "BottomEdge" "4200"
(**) Option "VertScrollDelta" "100"
(**) Option "FingerLow" "25"
(**) Option "FingerHigh" "30"
(**) Option "MaxTapTime" "180"
(**) Option "MaxTapMove" "220"
(--) Touchpad touchpad found
(**) Touchpad: always reports core events
(**) Option "CoreKeyboard"
(**) Keyboard0: always reports core events
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "auto"
(**) Mouse0: Device: "/dev/input/mice"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: always reports core events
(**) Option "Device" "/dev/input/mice"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5 6 7"
(**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
(**) Mouse0: Buttons: 11
(**) Mouse0: Sensitivity: 1
(II) evaluating device (Mouse0)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) evaluating device (Keyboard0)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) evaluating device (Touchpad)
(II) XINPUT: Adding extended input device "Touchpad" (type: MOUSE)
(--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(--) Touchpad auto-dev sets device to /dev/input/event5
(**) Option "Device" "/dev/input/event5"
(--) Touchpad touchpad found
Could not init font path element /usr/share/fonts/Type1, removing from list!
AUDIT: Mon Mar 3 00:21:47 2008: 10765 X: client 7 rejected from local host (uid 1001)
(II) intel(0): xf86UnbindGARTMemory: unbind key 0
(II) intel(0): xf86UnbindGARTMemory: unbind key 1
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x007bf000 (pgoffset 1983)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x00c80000 (pgoffset 3200)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB)
(II) intel(0): 0x00020000-0x0061ffff: compressed frame buffer (6144 kB, 0x000000007f820000 physical
(II) intel(0): 0x00620000-0x00620fff: compressed ll buffer (4 kB, 0x000000007fe20000 physical
(II) intel(0): 0x00621000-0x0062afff: HW cursors (40 kB, 0x000000007fe21000 physical
(II) intel(0): 0x0062b000-0x00632fff: logical 3D context (32 kB)
(II) intel(0): 0x00633000-0x00633fff: overlay registers (4 kB, 0x000000007fe33000 physical
(II) intel(0): 0x00640000-0x00c7ffff: front buffer (6400 kB)
(II) intel(0): 0x007bf000: end of stolen memory
(II) intel(0): 0x00c80000-0x01f3ffff: exa offscreen (19200 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is off
(II) intel(0): Display plane B is now disabled and connected to pipe B.
(II) intel(0): Pipe B is on
(II) intel(0): Display plane A is now enabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output LVDS is connected to pipe B
(II) intel(0): Output TV is connected to pipe none
(II) Mouse0: ps2EnableDataReporting: succeeded
(--) Touchpad auto-dev sets device to /dev/input/event5
(**) Option "Device" "/dev/input/event5"
(--) Touchpad touchpad found
Can anyone help me with this?
Last edited by bughunter2 (2008-03-03 01:06:30)The standard arch kernel includes all the required modules, at most you need to load them explicitly listing them in MODULES in /etc/rc.conf
You need also the hw specific stuff, that is i915 and intelagp. Check lsmod and see if they are loaded. If they are not, inspect dmesg and see if udev tries to load them and fails for some reason.
I remember some cases where intelagp and i915 are not loaded by udev in the right order, if this is your case you can try to list them in the right order in MODULES.
There should be no need to recompile the kernel or to install a particular version of dri (just use the arch packages for mesa, libdrm etc; but I guess you have them already) -
Can't get the software to work with Audigy 2
Hi, I have had my Audigy 2 ZS going on a year now and haven't had any problems. I recently made a clean install of Windows XP and upgraded to SP2 and all that. Now, I can get sound out of the card but can't get the software to work at all; cannot get the volume slider bar to appear when I click the icon (it appears in the task bar though and I get a small gray square where the slider should appear), the surround mixer does not show when I double click the volume icon, EAX conxole is a no go, get an empty error box when I try to start the Equaliser.
I have tried everything from simple re-install to clean sweep to praying to the pagan gods. I have alsoo tried updating the drivers of course.
I run XP on an Intel MoBo (on-boeard sound deactivated), 52RAM, ATI 9700 ALL-IN-WONDER.
DOES THE CREATIVE SOFTWARE DEPEND ON ANY WEIRD LITTLE WINDOWS SERVICE OR SETTING THAT I MIGHT HAVE CHANGED DURING SETUP?
This is quite infuriating as any idea I come up with takes up a lot of time in installation, uninstallation and clean up. It worked before, why not now?
Thanks in advance. dentoreOk I got it to work. This is the reply I got from Creative but I didn't remove the program from the add/remove option on the PC b/c that didn't work at first. I inserted the installation CD and remove it from that wizard. Rebooted and the PC found new hardware. I then installed the driver and software from the CD and now it works.
For Mediasource. It appears something was corrupted in Mediasource or there is a conflict within the system.Please uninstall all software and drivers for the soundcard, from add/remove programs. Once this is done, shut down the system and changePCI slots for the soundcard, then turn the system back on, cancel the found new hardware wizard, disable all background applications (especially virus scanner, firewall, and any other background applications running in the bottom right hand corner of the system), andthen perform a full reinstallation of the drivers and software from the soundcard installation cd.
CAT I hope you fix your sound card. Good luck. -
Can't get completion insight to work
Hi all,
I just can't get completion insight to work on the newer releases of sqldeveloper. It works fine until Version 1.5.5 Build MAIN-5969. However on both Version 2.1.0.62 Build MAIN-62.61 and Version 2.1.0.63 Build MAIN-63.73 it justn't work no matter what settings I use.
I have run both the builds from \sqldeveloper\bin\sqldeveloper.exe and no exceptions are reported.
This is the console output from 2.1.0.63
Finished parsing = 16
UsersCache.fillIn() time = 2015 ret==null?: false
Finished parsing = 0
Finished parsing = 0
Finished parsing = 0
Finished parsing = 0
*...?aux t2?, parse time = 172
Finished parsing = 0
Finished parsing = 0
InsightableOracleDatabase.fetch() time = 2609
select 'TABLE' type, user owner, name object_name, null column_name, null column
id, null datatype FROM sys.obj$ o
where o.owner# = 173
and o.name not like 'BIN%'
and o.type# = 2
and rownum <=50
union all
select 'VIEW' type, user owner, name object_name, null column_name, null column_
id, null data_type FROM sys.obj$ o
where o.owner# = 173
and o.name not like 'BIN%'
and o.type# = 4
and rownum <=50
Code completion time = 3516
Finished parsing = 0
*...?aux tok2?, parse time = 31
Finished parsing = 0
Finished parsing = 0
Finished parsing = 0
Finished parsing = 0
Finished parsing = 0
Finished parsing = 0
InsightableOracleDatabase.fetch() time = 38828
select 'TABLE' type, ''||o.owner# owner, name object_name, null column_name, nul
l column_id, null data_type FROM sys.obj$ o
where o.name not like 'BIN%'
and o.type# = 2
and rownum <=50
and name like ?
union all
select 'VIEW' type, ''||o.owner# owner, name object_name, null column_name, null
column_id, null data_type FROM sys.obj$ o
where o.name not like 'BIN%'
and o.type# = 4
and rownum <=50
and name like ?
union all
select 'TABLE' type, user owner, synonym_name object_name, null column_name, nul
l column_id, null data_type
from all_synonyms
where synonym_name like ?
and rownum <=50
and owner in (user,'PUBLIC')
AP_I%
AP_I%
AP_I%
Code completion time = 38984
Any help to get this working would be much appreciated.
ThanksThis console output says that the completion insight queries are executing - the first example took ~ 3.5 seconds and the second example took ~ 39 seconds. Unfortunately, it doesn't tell you how many records it returned.
If you copy the queries out of the console output and run them manually, do you get any results? For example, the second query would be:
select 'TABLE' type, ''||o.owner# owner, name object_name, null column_name, null column_id, null data_type
FROM sys.obj$ o
where o.name not like 'BIN%'
and o.type# = 2
and rownum <=50
and name like 'AP_I%'
union all
select 'VIEW' type, ''||o.owner# owner, name object_name, null column_name, null column_id, null data_type
FROM sys.obj$ o
where o.name not like 'BIN%'
and o.type# = 4
and rownum <=50
and name like 'AP_I%'
union all
select 'TABLE' type, user owner, synonym_name object_name, null column_name, null column_id, null data_type
from all_synonyms
where synonym_name like 'AP_I%'
and rownum <=50
and owner in (user,'PUBLIC')theFurryOne -
Help... I can not get my microphone to work
Help.... I can NOT get my microphone to work with my Blaster X-Fi XtremeGamer Fatal1ty Professional card. When I plug it in and test it (in either Configure Speech Recoginition - Windows Vista / or in Counter-Strike Source, Test Microphone Button under the game options) both indicate that the system is not receiving any sound. However, both the speakers (5.1) and headphones work fine. I am using a Plantronics headset.
I am not sure what I am doing wrong. Below are my complete system specifications. Let me know what additional information you need, if any.
-Michael
PS - Seems like I have a similar problem to this post (http://forums.creative.com/creativel...&message.id=58)
Motherboard: MSI K9A2 Platinum Socket AM2+ ATX
CPU: AMD|PHENOM 9600 2.3GHz
RAM: GeIL Evo One 8GB(4 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Quad Channel Kit
Video Card: Two (2) ATI Radeon HD 3870 512mb ddr4 w/hdtv & DVI - CrossFire Enabled
Power Supply: CORSAIR CMPSU-750TX TX 750W Power Supply
Monitor: Samsung 305T SyncMaster 30in Analog/Digital LCD Monitor
Hard drives: Two (2) Seagate Barracuda 7200.11 ST3500320AS 500GB 7200 RPM SATA 3.0Gb/s
Optical Drives: Two (2) Lite-On Super-Multi LH20A1H Lightscribe DVD Burner, PLEXTOR px-810sa 18x DVD+/-rw dual layer/dvd-ram SATA
Additional PCI cards: HAUPPAUGE wintv-hvr-1800 dual tuner ntsc/atsc/qam pci express, Creative 7.1 Channels PCI Interface Sound Audio Card: Blaster X-Fi XtremeGamer Fatal1ty Professional
Number of fans present: Seven (7) [2 Front - 1 Center - 1 Side - 1 Rear - 1 Power Supply - 1 CPU]
Video Card Drivers in Use: Catalyst Control Center
Message Edited by mac19406 on 02-10-200807:57 PMHere is the fix:
http://forums.creative.com/creativelabs/board/message?board.id=Vista&message.id=29191 -
I can't get my headphones to work
Hello,
My sound works perfectly through the speakers, but I can't get the headphones to work. The headphones work perfectly on Windows 7.
Please just tell me if you need some information about my hardware.
Cheers,
Sam.Thanks for the reply.
I do have a ~/.asoundrc file, here it is:
defaults.pcm.card 1
defaults.pcm.device 3
defaults.ctl.card 1
Here is the lspci | grep -i audio output:
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Redwood HDMI Audio [Radeon HD 5000 Series]
Here is the lsmod | grep snd output:
snd_hda_codec_hdmi 21248 1
snd_hda_codec_realtek 51810 1
snd_hda_intel 20208 1
snd_hda_codec 80733 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
snd_pcm 61237 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc 5901 2 snd_pcm,snd_hda_intel
snd_hwdep 4746 1 snd_hda_codec
snd_timer 14902 1 snd_pcm
snd 44394 9 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec,snd_hda_intel
soundcore 4378 1 snd
And finally, here is the aplay -l output:
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: ALC887-VD Analog [ALC887-VD Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: ALC887-VD Digital [ALC887-VD Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Generic [HD-Audio Generic], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
Hope this helps to give useful data.
Cheers,
Sam. -
i just downloaded AOL Desktop 1.7 for Mac and I can't get my email to work. It welcomes me but I know I have new email but it doesn't recognize that I have ANY mail at all. HELPPPPPPPP Please
Hey I've been all over and can't get any help. I'm well aware its not an Apple product but its an app for Mac OS so I thought I'd try here. I bought 2 new iMacs yesterday for my parents (5K) and I'm just trying to get them some help as there in their 70's and AOL is all they know.
But hey thanks for your help, -
My iPhone is using my work email to sign in to the cloud, but my apple id and password are with my "personal" email address. I can't get rid of my "work" email address on my iPhone 4S
Hi Sister Kate,
If you change the Apple ID you are using on an iPhone or other iOS device, there are several places you need to change it on the device. See this article -
Apple ID: What to do after you change your Apple ID
Thanks for using Apple Support Communities.
Best,
Brett L -
I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the MacBook Pro and connected to the TVs Component and Audio in ports.
Will not work. To my knowledge, dual converting like that isn't supported. The Mac must detect the connected video output device and that sort of info cannot be done across an analog component uni-directional connection.
-
Can't get video chat to work outside of LAN...
Hello,
I can't get video chat to work.
All computers, LAN and WAN are running the latest iChat under 10.4 (including latest updates).
Within our LAN, via Bonjour, everything is fine.
I'm now trying to set up an offsite Intel iMac (10.4) and I can't connect via video chat with them.
I've had this problem in the past and eventually gave up (so much for "it just works" - I've spent the last 10+ years dealing with Macs and Mac-based networking, I can't imagine "my dad" figuring this all out). Trying again with fingers crossed...?
If someone could help, it'd be much appreciated.
Thanks,
Kristin.
The studio router/firewall is a SonicWall TZ 170 Standard.
This router has a static IP.
All suggested ports on the SonicWall are set up correctly to allow in/out from our LAN.
All computers on the LAN have static IP addresses.
Quicktime streaming settings set as suggested.
OS X Firewall on all computers = OFF.
No iChat add-ons on any computers.
Internet connection speed = 7404 kb/s
The offside router/firewall is a LinkSys WRT54G
This router does not have a static IP.
DMZ is ON and set to the only computer connected to it.
Computer has a static IP address.
Quicktime streaming settings set as suggested.
OS X Firewall on all computers = OFF.
No iChat add-ons on computer.
Internet connection speed = 5116 kb/s
If any more information is required to help you help me, just let me know!Does the TZ170 have UPnP or Port Triggering then ?
I can not see that it does here
Opening the ports in the manner listed on that link will only allow one computer (IP) to use the open ports.
The Linksys is router and you have not mentioned what the modem is doing at that end.
Why not use UPnP here ? The Linksys does it (on the Administration page)
Most likely this needs the Respond to Anonymous Pings checked on the Security page.
9:29 PM Thursday; January 17, 2008 -
My "Hanging with Friends" app keeps crashing whenever I try to open it. I have deleted and re-downloaded the app, restarted my iPhone, and even restored my iPhone all together, and nothing is working. How can I get this app to work again?
Can you start Firefox in [[Safe mode]] ?
You can also do a clean reinstall and download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
You can initially skip the step to create a new profile, that may not necessary for this issue.
See http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall -
After upgrading to Lion can't get Boot Camp to work! Just get "The startup disk cannot be partitioned or restored to a single partition". Anytone?
This message, and threads like yours got asked daily for over two years, now it is only a couple times a week!!
Is it so hard to follow through? you were to have backup already, clones are best, then erase/format and restore.
Then partition.
Some have been able to use Disk Utility booted from OS X DVD or another drive, and repair the drive.
You have to use Boot Camp Assistant (99.9% anyway) to create and achieve a proper Windows Master Boot Record partition.
Maybe you are looking for
-
When I open firefox i am getting a new small browser window opening with some kind of ad (different ad each time). McAfee blocks the ad after about 10 - 15 seconds. I also noticed that while looking at ads on craigslist, a few of the words are differ
-
ADFc: No view port found when using both Browser dialog and TF inline-popup
Hi, Using JDev 11.1.1.2. We have a table with data and two commandlinks. One navigates to a task-flow-call configured to "run as dialog" in a modal inline-popup. This opens a modal inline-popup that can be used to modify the data. The second command
-
Major Problem w/ USB Sound Interface Driver
I want to start off saying that I have Parallels Desktop installed w/ a Windows 7 Guest OS. I have the Audio 8 DJ driver installed on Windows 7 AND OSX Lion. However when I plug the Audio 8 DJ interface in, it allows me to choose whether it will be c
-
My Tasks page in My Site doesnt appear after migration to 2013
We have recently migrated our My Sites from 2010 to 2013. everything has been migrated without issues except that when you click on Tasks in My Site page it takes you to the About me page instead. This is not the case for new users who are creating
-
Vlaues comparison error when using 'lt'
Dear all, I have a little problem with the comparison functions (lt, gt, eq, ne). Given the following XML document: <root> <node id='10,3,4,12'/> <node id='5,4,6'/> <node id='0,1,3'/> </root> I want to return only nodes having a number less than 3 in