Can't get VPN to work on RV220W

Question

I am a home office user who bought a RV220W router for the speed advertised on smallnetbuilder.  I am trying to set up the VPN but can't get it to work with the Quick VPN client.  I am using dyndns to manage the dynamic IP and have entered that into the setup noted below.  I can access the router remotely (remote administration) when enabled using the dyndns address so I know that is working.
IKE Policy Table
General
Policy Name:                 krafty001vpn    
Direction / Type             Responder    
Exchange Mode:           Aggresive    
Enable XAUTH Client:    None    
Local Identification
Identifier Type:               FQDN    
FQDN:                          krafty001.dyndns.org    
Peer IKE Identification
Identifier Type:               Remote Wan IP    
FQDN:                          krafty001.dyndns.org    
IKE SA Parameters
Encryption Algorithm:     3DES    
Authentication Algorithm:          SHA-1    
Authentication Method:          Pre-Shared Key    
Pre-Shared Key:          xxxxxxxxx    
Diffie-Hellman (DH) Group:          Group 2 (1024bit )    
SA-Lifetime:          28800 Seconds
VPN Policy Table
Add / Edit VPN Policy Configuration
Policy Name:
krafty001vpn
Policy Type:
Auto Policy
Remote Endpoint:
FQDN
krafty001.dyndns.org
NETBIOS:
Enable
Local Traffic Selection
Local IP:
ANY
Start Address:
End Address:
Subnet Mask:
Remote Traffic Selection
Remote IP:
ANY
Start Address:
End Address:
Subnet Mask:
Split DNS
Split DNS:
Enable
Domain Name Server 1:
Domain Name Server 2:
(Optional)
Domain Name 1:
Domain Name 2:
(Optional)
Manual Policy Parameters
SPI-Incoming:
SPI-Outgoing:
Encryption Algorithm:
                             3DES                             None                             DES                             AES-128                             AES-192                             AES-256                             AES-CCM                             AES-GCM                            
Key-In:
Key-Out:
Integrity Algorithm:
                             SHA-1                             SHA2-256                             SHA2-384                             SHA2-512                             MD5                            
Key-In:
Key-Out:
Auto Policy Parameters
SA-Lifetime:
3600
                             Seconds                             KBytes                            
Encryption Algorithm:
                             3DES                             None                             DES                             AES-128                             AES-192                             AES-256                             AES-CCM                             AES-GCM                                                       
Integrity Algorithm:
                             SHA-1                             SHA2-256                             SHA2-384                             SHA2-512                             MD5                            
PFS Key Group:
Enable
                             DH-Group 1 (768 bit)                             DH-Group 2 (1024 bit)                             DH-Group 5 (1536 bit)                            
Select IKE Policy:
                                                          krafty001vpn                                                                                     
Quick VPN Setip
User Profile: homevpn
User Name krafty001vpn
Password: xxxxx
Server Address:  krafty001.dyndns.org
Port for QuickVPN:   Auto
Any help in identifying what setup component I have configured incorrectly would be appreciated
Thanks

Answer 1

I am not sure this will help but make sure the following is set correctly:
Currently VPN is somewhat broken on all versions of firmware of the RV220W including beta where VPN will ONLY negotiate on 443. If you are port forwarding 443 to a server or something else it will fail. You must allow the VPN to authenticate on 443. The router SHOULD be able to connect on 60443 as indicated on the QUICKVPN software however it doesn't this has been confirmed by a CISCO engineeer I have been speaking with regarding my VPN woes. Currently there is NO ETA on this fix.
But since you didn't mention if your 443 ports were being routed elsewhere I figured i would lay out that information here incase you where. Also I strongly recommend contacting Cisco Support for the beta firmware it makes the RV220W much better.
Also the reason for the update to the beta firmware it resolves the hair pinning problem which could also lead to VPN issues.