Can't get Wireless enabled uisng Windows XP

Hello,
a friend of mine has a laptop, it was a gift, but he has a problem and he gave me the laptop to fix it.
The laptop has network driver but it has no Toshiba software in it.
I don't know why, and he lost his CD, and the problem is that I can't enable the network.
The laptop has a small LED for the wireless card, but it's off.
I tried Fn + F8, but the wireless is still turned off.
The driver seems to work fine, but it says no networks found.
I know it needs some utility but I can't find it.
The computer runs Windows XP.
Any idea how I can get wireless enabled?
I know you need Flash Cards but i can't find something similar for Windows XP.
I tried a HotKey Utility but it has only 2 options and they don't seem to work at all, but they are still irrelevant to wireless anyway.

Well, the drivers for old notebooks are placed in the Archive area.
http://www.toshiba.eu/innovation/download_drivers_bios.jsp
In Product Type choose Archive then navigate to the Satellite A60
There you should find all the Win XP drivers.
But it looks like Common Modules are not available for this A60 model/series.
As I said above, not all notebooks required Common Modules.
In your case you would need to install the +Hotkey Utility+ to control the FN keys.
Also Controls Utility and other software available on the Toshiba page should be installed

Similar Messages

How can I get Wireless N 5MHZ Capabilities Dual Band up to 300MHZ on my DV7 Laptop?

How can I get Wireless N 5MHZ Capabilities Dual Band up to 300MHZ on my DV7 Laptop?
Question for 4/18 experts ...
Or specifically, how can I replace my wireless card on a DV7-6B32US and upgrade to Intel Centrino 6230?
I have a relatively new DV7-6B32US puchased on 11/2011. Still under warranty. purchased 2 of the laptops. (also own 3 hp desktops and 1 HP All in One)
Existing card is wireless N but does not support 5GHZ or dual band. It is Broadcom 4313 wifi card and I am just realizing that the Broadcom card does not do the dual band 5GHZ wireless N. I have Linksys e4200 router which supports 5GHZ and dual band speeds up to 300 Mbps.
I called tech support and with their help identified Intel Centrino 6230 as the correct upgrade, and with their help ordered 631956-001. In the Maintenance Manual for DV7 laptop, this part number was listed for Intel Centrino 6230. Turns out HP sends an Intel Wireless N 1030 card, which is no better than my existing card. I called HP and they acknowledged that some manuals use part number 631956-001 for Centrino 6230 and some use 631956-001 for INtel 1030. So HP support said they would give refund but case manager was of no help in solving the upgrade problem. Said it was unavailable but here is your money back.
So after more searching, I see others have used part number 636672-001 to order Intel Centrino 6230, specifically for HP ProBook 4530s, 4230s, 4730s. And if I use part number 636672-001 and go thru parts store at HP, I can purchase it.
But will it work??
First, will the Intel Centrino 6230 with part number 636672-001 from HP parts, work in my HP DV7-6B32US, even though the part number is NOT listed in the Maintenance and Service Guide for my specific laptop. I see postings about whitelists and changing bios, etc, and am hoping someone can provide some guidance. I have been thru 2 tech support calls and one case manager and have gotten 3 different feedback from HP, from yes it will work and ordering the part, to buy it on amazon, to it will not work and here is your money back.
Second, I see some postings about Centrino 6230 and multiple antenna's. When I replaced the Broadcom 4313 with the Intel 1030 card, I simply unattached 2 wires and reattached the wires. And it worked. I am wondering if the reason HP doesn't list the 6230 card for DV7 is that DV7 does not have the antennas required to support 6230. Does the Centrino 6230 require 3 antennas?
Thanks for any suggestions. The existing cards do work but I paid extra for the Linksys e4200 Router and just assumed a winter 2011 $700 laptop from HP would use the latest wireless n technology, otherwise I would just keep existing cards.

I have went thru the exact same problems trying to upgrade the wireless card in my DV7. It is very frustrating that the wireless card can't be upgrade to one that supports 5Ghz. Here is my post from the network forum. http://h30434.www3.hp.com/t5/Wireless-Internet-Home/Unsupported-Wireless-LAN-6230/td-p/1419595 Doesn't sound like it is possible to upgrade to the Centrino 6230 without it being added the the "white list". Sound like HP doesn't update the list after shipping the notebook. I feel your pain. HP needs to help out the consumer in upgrading the wireless cards. I see we are not the only ones that have had this problem.

Can i get my music from windows media onto my iPod shuffle

I lost all the music on my ipod shuffle. It seems that my itunes library is empty. Can I get the music from Windows media player on a pc running windows xp and put it on my ipod? Thanks

your itunes account is your email address. you can try to see if you can sign in. you can always use one of these programs yamipod or music rescue.

My 1st ipod was lost. My library is on a Dell with Windows. I registered my new ipod to a Mac. How can I get my library from Windows onto my new Ipod?

My 1st ipod was lost. My library is on a Dell with Windows. I registered my new ipod to a Mac. How can I get my library from Windows onto my new Ipod?

Thank you for your help. I am still having trouble. As you can tell, I am not technologically advanced AT ALL. My music is all showing up in the library but when I go to file in the top left corner, Sync is greyed out and I cannot select it. I'm gonna continue to try this. It's been a long time since I had my 1st ipod and things have changed so much I will probably need to research this stuff. Thanks again for your help.

How can I get icloud on my windows xp PC.

how can I get icloud on my windows xp PC.

You can't.
http://support.apple.com/kb/DL1455
System Requirements
Microsoft Windows Windows Vista SP2 or Windows 7
Safari 5.1.1 or Internet Explorer 8 or later
Microsoft Outlook 2007 or 2010 recommended

Can I get rid of a windows partition on a MacBook running 10.4.11 without having bootcamp or bootcamp beta?

Can I get rid of a windows partition on a MacBook running 10.4.11 without having bootcamp or bootcamp beta? If so, how?

Yes, I think so, as would Snow Leopard probably. If your computer meets the requirements it would only cost $29 to buy Snow Leopard versus $129 for Leopard.
Snow Leopard General requirements
Mac computer with an Intel processor
1GB of memory
5GB of available disk space
DVD drive for installation
Some features require a compatible Internet service provider; fees may apply.
Some features require Apple’s MobileMe service; fees and terms apply.
Leopard System requirements
You must have a Macintosh computer with:
an Intel processor or a PowerPC G4 (867 MHz or faster) or G5 processor
a DVD drive >built-in FireWire
at least 512 MB of RAM (additional RAM is recommended for development purposes)
a built-in display or a display connected to an Apple-supplied video card supported by your computer
at least 9 GB of disk space available, or 12 GB of disk space if you install the developer tools

I'm new to boot camp and have always used Parallels which was easier to install but now I can't get my hands on Windows 8 for boot camp? What do i do?

I'm new to boot camp and have always used Parallels which was easier to install but now I can't get my hands on Windows 8 for boot camp? What do i do?

There is no Windows for Boot Camp. just buy a copy of Windows.

I have a credit in the iTunes store, but I can't get past the payment window to make a purchase. I don't want my credit card charged, so how do I do this?

How do I make a purchase from the iTunes store using a credit I have? I can't get past the payment window, and don't want my credit card charged instead of my credit.

same here but i cant purchase a movie or anything

How can I get wireless printing with my ipad?

How can I get wireless printing with my ipad?

Best way is to use an AirPrint compatible printer:
http://support.apple.com/kb/HT4356
If your printer is not AirPrint compatible, you might want to take a look at Printopia.
http://www.ecamm.com/mac/printopia/

Can i get wireless access with a 10.4.11

Can I get wireless access on the internet with a Dual core intel processor 10.4.11

If it has an Airport card fitted, yes.
It's very likely it already has, but to be certain, go to the Apple menu > "about this Mac" > More info
Under Network in the left pane you'll see Airport' select that and it'll tell you what card is fitted (if any).
You should also have in the menu bar on the right a pie-slice type symbol; click that and you'll get the option to switch on airport if it's present.
You'll need to set it up in Network Preferences to connect to your wi-fi router.

If i have a swiss adress & credit card can i get Hebrew enabled creative cloud and work globaly?

if i have a swiss adress & credit card can i get Hebrew enabled creative cloud and work globaly?
also... can i use my CS3 discount for creative cloud?
Thanks.
DAVID.

Hi David,
Products which support Hebrew have to be installed in this language from Adobe Application Manager.
Please see the instructions here:
http://forums.adobe.com/message/4881433#4881433
I believe Photoshop, InDesign, and Illustrator have right to left text support now.
I don't know about your CS3 discount, you can typically upgrade for a CS3 owned product.
-Dave

Can't get HT enabled ??

Hi
I have a Pentium 4 2.4Ghz HT and I can't get HT enable with this board...
I used a Asus P4PE with the same processor and with that board there where no problem with HT....
Bios version on my msi board are updated today (version 2.1)
Anyone have a solution ???

First, please post the specifications of your computer in your signature, along with the ratings of your power supply.
There should be a setting in the BIOS that turns on this feature, but this also depends on what motherboard your're using, since we don't know.

Can not get mac to run Windows Virtual PC

I tried to download VM 7 but I cannot get it to load. It says that I have downloaded it earlier today. I tried but was unsuccessful at downloading it. Is there any way of finding it with Finder so I can uninstall it?

Windows on Intel Macs
There are presently several alternatives for running Windows on Intel Macs.
1. Install the Apple Boot Camp software. Purchase Windows XP w/Service Pak2, Vista, or Windows 7. Follow instructions in the Boot Camp documentation on installation of Boot Camp, creating Driver CD, and installing Windows. Boot Camp enables you to boot the computer into OS X or Windows.
2. Parallels Desktop for Mac and Windows XP, Vista Business, Vista Ultimate, or Windows 7. Parallels is software virtualization that enables running Windows concurrently with OS X.
3. VM Fusionand Windows XP, Vista Business, Vista Ultimate, or Windows 7. VM Fusion is software virtualization that enables running Windows concurrently with OS X.
4. CrossOver which enables running many Windows applications without having to install Windows. The Windows applications can run concurrently with OS X.
5. VirtualBox is a new Open Source freeware virtual machine such as VM Fusion and Parallels that was developed by Solaris. It is not as fully developed for the Mac as Parallels and VM Fusion.
Note that Parallels and VM Fusion can also run other operating systems such as Linux, Unix, OS/2, Solaris, etc. There are performance differences between dual-boot systems and virtualization. The latter tend to be a little slower (not much) and do not provide the video performance of the dual-boot system. See MacTech.com's Virtualization Benchmarking for comparisons of Boot Camp, Parallels, and VM Fusion. Boot Camp is only available with Leopard or Snow Leopard. Except for Crossover and a couple of similar alternatives like DarWine you must have a valid installer disc for Windows.
You must also have an internal optical drive for installing Windows. Windows cannot be installed from an external optical drive.

Re: Portege M800 - can't get bluetooth installed in Windows 7

Hi, I have a portege M800 PPM81C-07602D. It came with windows vista but I have reinstalled it to windows 7, and now I can't get the bluetooth drivers to install. I've tried the old vista drivers as well as the newer windows 7 drivers, but whenever I run the install I get the message "Please plug in the bluetooth device and click ok button."....If I click ok it just pops up again. I don't know why it wouldn't be finding the internal bluetooth....I dont think there's a physical on/off switch for the BT anywhere, and I looked to see if it had been disabled in the bios but there was nothing in there about it...so...I'm out of ideas.
Anyone have any thoughts I can try?
Any help is appreciated, thanks!

Toshiba Bluetooth stack can be installed if the BT module is enabled properly so use FN+F8 key combination to enable BT module.
After doing this BT should be recognized and installed properly (you will se BT entries in device manager).

Can't get printer to work (Windows - Arch)

I have an XP box and my Arch box on my home network, have Lexmark X1100 connected to XP box (USB printer). It worked fine on Ubuntu, I know it can work but I haven't gotten anything going using the Arch wiki on CUPS. Here is my /etc/samba/smb.conf:
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options (perhaps too
# many!) most of which are not shown in this example
# For a step to step guide on installing, configuring and using samba,
# read the Samba-HOWTO-Collection. This may be obtained from:
# http://www.samba.org/samba/docs/Samba-HOWTO-Collection.pdf
# Many working examples of smb.conf files can be found in the
# Samba-Guide which is generated daily and can be downloaded from:
# http://www.samba.org/samba/docs/Samba-Guide.pdf
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentry and a ; for parts of the config file that you
# may wish to enable
# NOTE: Whenever you modify this file you should run the command "testparm"
# to check that you have not made any basic syntactic errors.
#======================= Global Settings =====================================
[global]
# workgroup = NT-Domain-Name or Workgroup-Name, eg: MIDEARTH
workgroup = MYGROUP
# server string is the equivalent of the NT Description field
server string = Samba Server
# Security mode. Defines in which mode Samba will operate. Possible
# values are share, user, server, domain and ads. Most people will want
# user level security. See the Samba-HOWTO-Collection for details.
security = user
# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
; hosts allow = 192.168.1. 192.168.2. 127.
# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
load printers = yes
# you may wish to override the location of the printcap file
; printcap name = /etc/printcap
# on SystemV system setting printcap name to lpstat should allow
# you to automatically obtain a printer list from the SystemV spool
# system
; printcap name = lpstat
# It should not be necessary to specify the print system type unless
# it is non-standard. Currently supported print systems include:
# bsd, cups, sysv, plp, lprng, aix, hpux, qnx
; printing = cups
# Uncomment this if you want a guest account, you must add this to /etc/passwd
# otherwise the user "nobody" is used
; guest account = pcguest
# this tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/%m.log
# Put a capping on the size of the log files (in Kb).
max log size = 50
# Use password server option only with security = server
# The argument list may include:
# password server = My_PDC_Name [My_BDC_Name] [My_Next_BDC_Name]
# or to auto-locate the domain controller/s
# password server = *
; password server = <NT-Server-Name>
# Use the realm option only with security = ads
# Specifies the Active Directory realm the host is part of
; realm = MY_REALM
# Backend to store user information in. New installations should
# use either tdbsam or ldapsam. smbpasswd is available for backwards
# compatibility. tdbsam requires no further configuration.
; passdb backend = tdbsam
# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting.
# Note: Consider carefully the location in the configuration file of
# this line. The included file is read at that point.
; include = /usr/local/samba/lib/smb.conf.%m
# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
; interfaces = 192.168.12.2/24 192.168.13.2/24
# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply
; local master = no
# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable
; os level = 33
# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job
; domain master = yes
# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election
; preferred master = yes
# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
; domain logons = yes
# if you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
; logon script = %m.bat
# run a specific logon batch file per username
; logon script = %U.bat
# Where to store roving profiles (only for Win95 and WinNT)
# %L substitutes for this servers netbios name, %U is username
# You must uncomment the [Profiles] share below
; logon path = \\%L\Profiles\%U
# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
; wins support = yes
# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
; wins server = w.x.y.z
# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one WINS Server on the network. The default is NO.
; wins proxy = yes
# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The default is NO.
dns proxy = no
# These scripts are used on a domain controller or stand-alone
# machine to add or delete corresponding unix accounts
; add user script = /usr/sbin/useradd %u
; add group script = /usr/sbin/groupadd %g
; add machine script = /usr/sbin/adduser -n -g machines -c Machine -d /dev/null -s /bin/false %u
; delete user script = /usr/sbin/userdel %u
; delete user from group script = /usr/sbin/deluser %u %g
; delete group script = /usr/sbin/groupdel %g
#============================ Share Definitions ==============================
[homes]
comment = Home Directories
browseable = no
writable = yes
# Un-comment the following and create the netlogon directory for Domain Logons
; [netlogon]
; comment = Network Logon Service
; path = /usr/local/samba/lib/netlogon
; guest ok = yes
; writable = no
; share modes = no
# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
;[Profiles]
; path = /usr/local/samba/profiles
; browseable = no
; guest ok = yes
# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
comment = All Printers
path = /var/spool/samba
printing = cups
printer = x125
browseable = yes
# Set public = yes to allow user 'guest account' to print
guest ok = yes
writable = no
printable = yes
# This one is useful for people to share files
;[tmp]
; comment = Temporary file space
; path = /tmp
; read only = no
; public = yes
# A publicly accessible directory, but read only, except for people in
# the "staff" group
;[public]
; comment = Public Stuff
; path = /home/samba
; public = yes
; writable = yes
; printable = no
; write list = @staff
# Other examples.
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
; comment = Fred's Printer
; valid users = fred
; path = /homes/fred
; printer = freds_printer
; public = no
; writable = no
; printable = yes
# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
; comment = Fred's Service
; path = /usr/somewhere/private
; valid users = fred
; public = no
; writable = yes
; printable = no
# a service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %U option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
; comment = PC Directories
; path = /usr/pc/%m
; public = no
; writable = yes
# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
; path = /usr/somewhere/else/public
; public = yes
; only guest = yes
; writable = yes
; printable = no
# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
;[myshare]
; comment = Mary's and Fred's stuff
; path = /usr/somewhere/shared
; valid users = mary fred
; public = no
; writable = yes
; printable = no
; create mask = 0765
And I followed this: http://wiki.archlinux.org/index.php/CUPS specifically http://wiki.archlinux.org/index.php/CUP … rinter_PPD and http://wiki.archlinux.org/index.php/CUP … s_to_Linux. But I run OO and I still only have Generic printer.
I was using the Gnome cups manager on Ubuntu, but I cannot find this package on my system now. I see it in AUR but shouldn't it be in pacman? I have searched and searched but can't find it. And I installed gtklp, but upon startup it just gives me "No printers found!" and exits.
EDIT: I have just built gnome-cups-manager from AUR and am at the point where I select a driver, however in the Manufacturer list there is nothing showing, and when I hit Install Driver and select the .ppd I got from the CUPS site for my printer, it just says "The PPD /usr/share/cups/model/Lexmark-X125-drv_x125.ppd is already installed" I can't get past this point??
Last edited by colbert (2008-01-09 17:34:32)

on xp box
1) install and start lpd daemon (done)
2) set printer sharing (short name, no spaces) (done)
3) make sure that xp allows tcp 515 (done?)
on linux
1) start cups
2) open konqueror (not firefox) and enter in the address bar
http://localhost:631/
log in as root (I assume that basic cups with user is configured)
3)select add printer
- first page:set priter description
- second page: Select device lpd/lpr host or printer
- third page enter lpd://hostname/queue (hostname if defined in /etc/hosts, otherwise ip address of XP box queue -> printer share name
- fourth page select manufacturer
-fifthpage driver
test it
KDE
K Menu -> Settings ->Printers ->Add -> follow screens
I found KDE method (under Arch) more reliable, but both should work. No idea about Gnome.
next
Last edited by broch (2008-01-10 01:15:24)

Can't get Wireless enabled uisng Windows XP

Similar Messages

Maybe you are looking for