Can't hear an audio track that I have recorded.

I recorded an audio track through my preamp to my motu interface and it displayed the wave form in the track but I never heard it through the headphones of the interface when I was monitoring and during recording or in playback. I did in that project. hear all the other midi files I had been arranging. This seems strange I can see it but not hear it. I checked my audio set up to run in and out of the PCI on the Motu unit. So where is that sound then?
thanks for your gracious help.
Jason.

Is the audio file placed on an audio track (no instrument or midi track)?
Did you select the correct output for this audio track?
(sorry for the question: any mute or solo buttons turned on?)
To hear your recording signal during recording you have either to switch "Software monitoring" to on or use the direct monitoring of your audio interface. Software monitoring routes the recorded signal through logic which will cause latency. Direct monitoring will reduce latency but you have to setup your audio-interface mixer properly.
Eddie

Similar Messages

I can not hear the audio tracks in iMovie

I can not hear the audio tracks in iMovie 10.0.1.
Can anyone help me?

Have a look in Utilities > Audio Midi Setup

Can only hear 1 audio track?

I,m new to Elements 10 and have just started editing. I just dragged a clip onto my timeline but can only hear one audio channel. I know there are two tracks, how can I mix both through?
thanks. Darrell

Hi Steve, thanks for your help. but this has really got me beat. When I play the track straight off my computer I hear all audio tracks. But then I “get media” bring the clip in and listen off the elements timeline – I only hear track one???
So my computer must be fine?
When you say “Can I see both right and left channel in the wave form? Its hard to tell – am I meant to be looking at the “green strip “ on the timeline? Its so very small. - I see a yellow line and a grey line underneath? what am I looking at. Its very frustrating because I am trying to edit a friends concert and the music is on track one – but the atmos and applause is on the other 3 tracks – but all I can hear is the music
any suggestions?
cheers mate
Darrell Brown
0418-954-858
[email protected]

How can I revert my audio clips that I have edited in Soundtrack Pro back to the original audio?

I edited a project in FCP6 and sent numerous audio clips to Soundtrack Pro where I sampled and removed some AC and fridge compressor
hum from some interview footage. I'm sending the project out for professional sound mixing and they advised me to restore the original
audio to prevent the creation of artifacts when they process the sound in a different program.
Is there some way to "revert" all my clips that I edited in Soundtrack Pro back to the original audio without going back to
my original interview footage and cutting in clip by clip? (Next time I'll save my original audio on a duplicate timeline -- live and learn!)
Thanks in advance for any helpful ideas!

What happens if duplicate the sequence, then choose one of them to use "match frame" to get back to the original clips?
x

On my ipad 2 I can't "see" the hundreds of spoken audio tracks that are in my itunes and on my ipod touch. Is there something I didn't do during sync up?

On my ipad 2 I can't "see" the hundreds of spoken audio tracks that are in my itunes and on my ipod touch. Is there something I didn't do during sync up? The tracks are from voice recordings that were downloaded from an extrernal drive and weren't necessarily tagged as spoken audio. Do I need to go back into itunes and relabel these tracks so they will show up on my ipad2?
Thanks in advance for your help!

With the iPad connected to the computer, while iTunes is running, click on the iPad name on the left side under devices. Click on the Movies tab and look for Movie Rentals. You want to "Move" the films to the iPad.

Using Pro Logic X to record. I have several tracks and I'm trying to record an audio track. I have the mic connect to Avalon 737 then into apollo interface. When I record all track are being recorded into that track. I can't just get the audio to record.

Using Pro Logic X to record. I have several tracks and I'm trying to record an audio track. I have the mic connect to Avalon 737 then into apollo interface. When I record all track are being recorded into that track. I can't just get the audio to record.

Thanks for responding. Everything seems to work right except for the when I plug into the 737. Ok let me see if I can be more clear. I had this set up done with two representatives of Neumann, and DBox. Here it is I hope this helps. 32 Channel snake (24 Inputs 8 outputs) Channels 1-8 from snake to my Octopre for Drums. From Octropre output quarter inch lines into the Apollo 2, quarter inch input. This is so that the Apollo 2 is taking the drum tracks. Snake Channel 9-12 into Apollo 1 channels 1-4 xlr. Snake Channel 13-16 into Apollo 2 Channels 1-4 xlr. Snake Channel 17 into the 737, output of 737 into Channel 5 of the Apollo 1 quarter inch.
Ok The Dbox. Sum output L&R into channel input 7&8 of Apollo 1. Apollo 1 output channels 1-8 into summing input channel 1-8 of Dbox. Apollo 1 main L&R going to main analog input L&R of Dbox. Spid out to DAW input of Dbox. I have both ADAT of both Apollos connected by optical wire. Also have port 2 of Apollo 1 into port 1 of Apollo 2 connected by Firewire. Let me know. Hope I got it right. Thanks for responding.

I can't hear the narration track over the audio, what do I do? And where is the "audio mixer"?

Just downloaded Premiere Elements 12 and lost my favorite audio music (wish I could bring it over from 11 somehow), so I drug a new clip in the audio track and now I can't hear my narration track. Also, can you pull up projects made in 11 with Premiere 12? Should I delete 11 off my computer? Also, where is the audio mixer?

The Audio Mixer is under the Tools menu in Expert view or under the Tools drop-down menu at the top of the interface.

How can i use original audio track in video editing for iPad 2?

I am struggling to understand how the video editing apps work for iPad 2, and specifically, to understand why all the editing apps I have looked at explain how you can make these terrific video clips by ADDING audio tracks from iTunes, or. From the audio library. I just want to use the original audio on the tape? Is that so strange? Today I took a video clip of my daughter singing with her guitar. I wanted to shorten the length a bit, so I downloaded a couple of Visio editing apps. When I pulled the clip out of my Camera Roll storage into the video editing screen, there was no sound at all,though there were ways to add other sounds ( for .99cents) most frustrating is that nowhere, does Apple explain this. The tutorials just show someone editing a video of their friends ( with no sound) And adding text and music, as if it's normal not to include the actual sound that originally accompanied the video clip. Seems like i wouldn't be the only customer who would prefer to hear my daughters own voice Ina video of her singing, and would like thisexplainedbefore I started downloading editing apps. If it can't be done, couldn't This be posted?

I am not understanding your question, or your complaint, if it is a complaint.
I movies takes a video clip, including its audio track.
You have the option of mutimg it, or of importing some other sound from your music library, or narrating. What other option do you want?

My iMovie is skipping like crazy when I try to edit and then goes to a black screen and you can only hear the audio!?!? What's happening??

I use iMovie almost everyday for Youtube videos. I have nothing in my imovie except the 5 clips that I'm editing now. I have all my media on an external hard drive and delete everything after I'm done with ( I empty all trash cans). My iMovie is now skipping when I try to edit and then the clips just go to a black screen and I can only hear the audio, this has been going on for a week and I don't know what to do?!? Any help?

Try Resetting your Mac's PRAM and NVRAM
If that doesn't help, try Resetting the System Management Controller
-- Those links are currently down for maintenance but should available shortly.

I am editing a clip but it won't show in the screen, I can only hear the audio. any suggestion?

I am editing a clip but it won't show in the screen, I can only hear the audio. any suggestion? The clip is visible in the timeline but when I play it I can only hear the audio and no images.

Hey, I'm having the exact same problem.
I just got my Macbook Pro and I tried to partition/install windows xp the first day I got it. After successfully partitioning my HD, the 50GB partition didn't show up while trying to install the windows platform.
To be a bit more specific, it doesn't even show up in my startup disk in the system preferences menu (if that's any help?)
So after about a week of abandoning my Macbook and going back to my PC I went to the Apple store and someone from the genius bar just told me to reformat the entire thing...so that's what I did and I'm still having the same problem.
Any advice Lyssa?

WMA audio files can only placed in audio track 8 for some reason

Using CS3. The only other audio tracks that have any files in them are tracks 1 through 3 . The WMA files in track 8 were recorded from a small digital recorder.
Every other audio file..... mp3 and the captured mpeg's audio portion.... can go in any audio track.
Why are these WMA files not able to be placed in the other tracks?

Per Harm's comment, you can look at the Audio Track Header for the little "speaker" icons for each Track: one speaker = mono, two speakers = stereo, and "5.1" = a 5.1 Audio Track.
If you set up your Project/Sequence with the required Audio Track types for your Assets, you can have your mono, or 5.1 Audio Tracks almost anywhere you want, and can also change the name, from say "Audio 1" to "SFX_Mono_01."
Also, if you have a bunch of unused Audio (or Video) Tracks, you can Delete those, or can create new ones, about wherever you wish. If you do not have the proper type of Audio Track created, PrPro will create a new one, of the proper type, for you. Just drag your Asset to below the Master, and boom! a new proper Track will appear, with the Clip in it.
Good luck,
Hunt

When i take a call or dial a call in the high density traffic area or noicy area i can't hear properly so at that time i put my phone in the loud speaker mode.

when i take a call or dial a call in the high density traffic area or noicy area i can't hear properly so at that time i put my phone in the loud speaker mode.

I have had this happen to me on 3GS, 4 and 4s. Usually the solution is one of the following:
1- If your volume indicator says headphones even though they are not plugged in, then:
Stick your headphones into the headphone jack and then remove quickly.
2. If that does not work Power your phone off. Then when restarting Reset the phone by pressing the home button and the power button at the same time until the apple logo appears.
3. Make sure you have not chosen to send audio to an Airplay device such as Apple Tv.
Hope one of these works for you

Adobe Premier Pro CS4 can't play mpg audio track - any fix?

Hello
I need some help about Premier Pro CS4:
I'm using Mac OS X 10.5.8 and adobe premier CS4
I Imported a video file .mpg to timeline, but the audio track is'nt vilible or playable, it's just like it doesn't have any just like.
The file came from DVD, after demultiplex, using Vob2Mpg (open source software), this operation produced a file with mpg extension - the file that does'nt work.
I looked in the web and some say that it works on adobe premier CS3
Anything that can fix this, any solution?
thanks

Adobe Premier Pro CS4 can't play mpg audio track - any fix?
Hello
I need some help about Premier Pro CS4:
I'm using Mac OS X 10.5.8 and adobe premier CS4
I Imported a video file .mpg to timeline, but the audio track is'nt visible or playable, it's just like it doesn't have any sound.
The file came from DVD, after demultiplex, using Vob2Mpg (open source software), this operation produced a file with mpg extension - the file that does'nt work.
And Quick Time doesn't recognize it as video file
I looked in the web and some say that it works on adobe premier CS3
Anything that can fix this, any solution?
thanks, again, sorry about the errors in the first post

How can I keep my audio track, delete a short segment of video, and reinsert a new video clip, without changing the audio with the way it lines up with the original video?

How can I keep my audio track, delete a short segment of video, and reinsert a new video clip, without changing the audio with the way it lines up with the original video?

If you have either iMovie 09 or iMovie 11 you can do this easily using the Cutaway feature.
Go to iMovie/Preferences and make sure that the Advanced Tools are enabled.
Now you jut drag and drop the 2nd clip onto hte first clip at the frame where you want the Cutaway to start. A popup menu will appear. Choose Cutaway.
Here is a good Tutorial.
If you have iMovie 08, let me know. There is a way to do it, but it is more complex.

How can I edit imported audio track? After selecting and deleting region and joining remaining parts, it keeps playing the track with the deleted part! What am I doing wrong?

How can I edit imported audio track? After selecting and deleting region, and joining remaining parts, it keeps playing the track with the deleted region!
What am I doing wrong?

After selecting and deleting region, and joining remaining parts, it keeps playing the track with the deleted region!
What am I doing wrong?
How exactly are you doing this?
When I cut out a part of an audio region, then drag the remaining parts together, so they are touching, the track will skip the cut out section when playing the file. Also, if I select the remaining parts of the region and use the command "Edit > join regions". This will create a new audio file with the cut out part deleted.
You should see this prompt, when you are joining the regions:

Can't hear an audio track that I have recorded.

Similar Messages

Maybe you are looking for