Can't install canon pixma mp 980 for wireless printing

I've installed the canon pixma software for the mp 980 and ran the connection test and got a very good connection. When I try to add the printer , I've clicked on "More Printers" and it scanned to look for drivers and didn't come back with any results. I can't get the printer to show up in the list of available printers.
My Macbook is connected to the LAN wirelessly and the printer has been set up to print wirelessly. I have a Windows machine on the network that can print to the printer.
Any suggestions?

It could be a WPA key issue but I have never had such a problem with my MP980 to confirm this. You could try temporarily disabling the encryption and then seeing if the printer can be found. Note that you will have to reconnect the printer via USB to set the changes in the machine.
If disabling the encryption does not help, then I would ensure that you can ping the IP address of the MP980. If you don't get a reply, then it would indicate that something went wrong with the network setup and this is why the device is not seen in the More Printers > Canon IJ Network menu.
If you do get a response, then there could be something blocking the advertising of the printer, such as the internal firewall of the Mac. This has to be set to 'Allow all incoming connections' for the printer to be seen.

Similar Messages

Can I use an old UFO Extreme for wireless printing?

Greetings, I have a new airport extreme base station managing my wireless network, but I am still printing wirelessly from a Macbook Pro by sharing a printer with wired a G4 desktop. (my 'main' BS is in the basement, G4 and printer on the 3rd floor, connected to the BS via ethernet). I have an older UFO style base station gathering dust that I'd like to use for wireless printing by having it sit next to the printer and connect to it via usb, join my existing network wirelessly, and, well that's it. Essentially I want it to be an airport express, so I can print wirelessly without the G4. Is this an easy/possible setup? What settings will I have to change on my 'main' airport BS as well as the UFO? Any guidance you can give me I'd very much appreciate. Many thanks in advance, and sorry for what I suspect is a dumb question.

Badlyva, Welcome to the discussion area!
The AirPort Extreme base station (AEBS) can not join a wireless network like the AirPort Express (AX) can. But you could configure your new AEBS to act as a WDS main base station and the old AEBS to act as a WDS remote base station. The bad part is that you would need to use 802.11g and the WDS link would cut your available wireless bandwidth in half of that.

I need to reinstall my Canon Pixma Pro 9500 MK 2 printer on my iMac running Mavericks. It looks for software but Apple cannot find. The driver is available on my computer. Is there a way I can force the installer to use the available driver?

I need to reinstall my Canon Pixma Pro 9500 MK 2 printer on my iMac running Mavericks. It looks for software but Apple cannot find. The driver is available on my computer. Is there a way I can force the installer to use the available driver?

I need to reinstall my Canon Pixma Pro 9500 MK 2 printer on my iMac running Mavericks. It looks for software but Apple cannot find. The driver is available on my computer. Is there a way I can force the installer to use the available driver?

I desperately need help installing Canon Pixma ip6000D printer in Windows 7 64-bit

My software CD (drivers, etc.) will not work with Windows 7 64-bit. I have tried running it in Windows XP compatibility mode, but it says it is made for 32-bit and will not work with 64-bit. Canon's website says it has an add-on module, but it doesn't have
the printer driver, and it says "Your printer must be installed via Microsoft Update before you download and use this module." I have tried to find a way to install the printer via Microsoft Update, But I can't find any information
about how to do this.
I have also done searches for the canon pixma ip6000d drivers for windows 7 64-bit, but all the results I have seen say that they are an add-on modules.
I would GREATLY appreciate any help with this.

After doing some more digging, I found a solution, and hopefully it will help anyone else who is having problems. Go to this page:
http://windows.microsoft.com/en-US/windows7/Install-a-printer
You can manually install the printer by following these instructions. If the model of your printer does not show (mine didn't), click the update button. It will take several minutes (maybe longer if you have a slow internet connection), but eventually it
will bring up a new list of printers. Just choose your printer and follow the instructions. My printer is working fine now.

I installed Canon Pixma MG5520, since, always get "canon quick menu has stopped working" how do I fi

I installed Canon Pixma MG5520 on win 7, since, always get "canon quick menu has stopped working" how do I fix please?

Hi thaluza,
We can see if there are files in a folder called TWAIN_32 other than those related to the printer that may be causing a conflict with the Quick Menu. If there are, we can temporarily remove the files to see if this will resolve the issue.
To move the non-Canon Twain files from the Twain_32 folder, please follow these steps:
1. Go to Computer / My Computer and locate the C: drive, then double-click on it to open.
2. Locate the WINDOWS folder, then double-click to open it.
3. Locate the TWAIN_32 folder, then double-click to open it.
4. Inside of the TWAIN_32 folder, you will see a folder for your printer as well as a WIATWAIN.DS file. If there are other files in that folder, you will want to move them to another location, preferably your Desktop by doing the following:
4-1. Click on each of the other items in the folder other than the the WIATWAIN.DS file and the folder for your printer to select them. You will want to hold the the CTRL key on your keyboard while selecting each of the items until all of the items except for the two referenced above are selected. Please be sure to leave the WIATWAIN.DS file and folder related to your printer inside of the TWAIN_32 folder.
4-2. With all of the items you want to move selected, please go to the EDIT menu and select the CUT option.
4-3. Go to your Desktop (main window that comes up when you start Windows with all of the icons on it) and right-click your mouse in any blank area, then choose the PASTE option. The items you selected from the TWAIN_32 folder should appear on the Desktop.
5. Try to launch the Quick Menu again.
Hope this helps!
This didn't answer your question or issue? Please call or email us at one of the methods on the Contact Us page for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

HT2250 I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour. Is that correct?

I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour. Is that correct?
paul.kelly

Hi Steve,
No expert, but since nobody else has piped in...
Did you setup the DNS Server IP?

How can I install the Amazon Kindle plugin for InDesign in InDesign CC?

How can I install the Amazon Kindle plugin for InDesign in InDesign CC? I have it installed in InDesign CS6 and it works fine.

Amazon has not updated the Kindle plugin for Indesign CC.

I have a macbook with 10.6 os and i can't get my new hp 6600 officejet online for wireless printing.

i have a macbook with 10.6 os and i can't get my new hp 6600 officejet online for wireless printing.

OK, thanks for that.
Download and install this: http://support.apple.com/kb/DL907
Reset the printing system:
- Go to System Preferences > Print & Scan
- Right (or control) click in the rectangle listing your printers and select Reset Printing System.
WARNING - this will delete ALL of your printers!
- Select the plus sign to re-add a printer. Select the Defualt tab on the top of the window. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Photoshop Elenents 13 does not recognize my Canon Pixma Pro Mark II 9000 printer.

Photoshop Elements 13 does not recognize my Canon Pixma Pro Mark II 9000 printer. I get the following error message “The saved printer information is not compatible with this version of Photoshop Elements, or the saved printer is no longer available. You will need to check your printer settings before printing” and I cannot print.

I have been checking my computer files and find that PSE 13 is only the 32 bit system and my computer is a 64 bit system. In PSE 12 I was able to take the Adobe
Twain Driver (Twain 32 bit} in to the Optional Plug-in folder and then my Canon Scanner would work with PSE 12. My printer Canon Pixma Mark II 9000 worked with PSE 12. Now that I have upgraded to PSE 13 neither the scanner or my printer will work. There I no “Optional Plug-in Folder” in PSE 13. Is there some way that I can drag files into PSE 13 that will enable both my scanner and printer to work? My scanner is a Canon Canoscan 8800.
Or must I go back to using PSE 12.
Robbie

Can not connect All in one 209b to new router for wireless printing....

Have an HP laptop and All in one priner 209b. All was working fine, wired and wireless printing. Then we had to upgrade our ATT Uverse router. Everything works...even wireless laptop and printer when connected to laptop. However, can't get printer to printer wireless since it has the old router info. I used the disk but when it asks to you to pick the printer, I choose the printer but it says printer now found ??? what ???? and this is with the cable connected. I do not have the wizard on the touch screen but I did reset to factory settings hoping it would load new router info but it does not. How do you manually enter router into for wireless printing. Is it best to delete the printer and reinstall as new...wired and then wireless ???
I am about to call an outsite company and pay the outrageous charge as the help on HP is not working. Thanks

Try this utility:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02114394&cc=us&dlc=en&jumpid=reg_r1002_usen&lc=...
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

How can I get the template( word rtf ) for PO – Printed Purchase Order ?

I want to convert the “PO - Printed Purchase Order” report from Oracle rdf format to BI Publisher. I am looking for the template but could not find in UNIX.
As per the Oracle blog, the template is available. Please see the URL : https://blogs.oracle.com/xmlpublisher/resource/121BIPReports.pdf
The template code is POXPRPOL_XML.rtf
when I look at the $PO_TOP/patch/115/publisher/templates/US directory, I cannot find POXPRPOL_XML.rtf
How can I get the template( word rtf ) for PO – Printed Purchase Order ?
Thank you,
Biju Varghese.

How can I get the template( word rtf ) for PO – Printed Purchase Order ? XML Publisher Administrator -> Templates
find by code or name
open it and you can downloadtemplate by "download" button

I have a hp deskjet 3050 all-in-one printer how can i setup for wireless printing my os is windows7.

how do i setup my hp deskjet 3050 all-in-one printer for wireless printing my operating system is windows7

Unplug the USB cable. Now go to Start > All Programs > Hewlett-Packard > Deskjet 3050 > Add a Device. Run the program and choose Wireless as the installation type.
Follow the directions. It will ask you to connect a USB cable temporarily. Do not connect until it asks and remove it when it tells you.
Finally, when you are done, go to Control Panel > Devices & Printers and delete the USB instance of the printer so you don't get confused when printing.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

HP LaserJet Pro P1102w printer "Ready" for wireless printing, but gives "error -- printing" message

This P1102w printer was configured for wireless printing from two computers (WinXP and Win7), both with a network sharing designation, and all functions worked perfectly:
Printing from the WinXP computer directly, and from a networked Win2K computer as a guest.
Printing from the Win7 computer directly, and from a networked Win2K computer as a guest.
Windows Printer Test Pages were printed from both installed computers, showing correct computer names, the printer name, Port names (IP addresses), Data format (IMF), Driver information, etc.
Several days later (after new boots), the WinXP computer showed printer status as being "Ready", along with the correct printer "Type" (HP LaserJet Professional P1102w), "Where" (IP address), and "Comment" (network printing). When a print job was submitted from Microsoft Word, the control-panel printer window first showed the message "printing", and then the message "error -- printing". Nothing was printed. The same results occurred when a print job was sent to the WinXP computer from the networked Win2K computer. HP’s troubleshooting routine did not identify the error, its cause, or what can be done about it.
Successful printing continued, as before, from the Win7 computer directly, and from the networked Win2K computer to the Win7 computer as a guest.
The printer’s blue “i” network indicator lamp is lit, and all three computers continue to communicate through the hub to each other and to the Internet.
HP’s printer installation program was executed on the WinXP computer, using the “fix” option, but nothing changed. The installation program was executed again on the WinXP computer, using the “new install” option (without removing the existing P1102w installation); the “browse” function saw the network, but no printers were found, and the installation could not be completed.
This is very perplexing. Any suggestions?
PS: The same problem occurred once before, and it was fixed by resetting factory defaults on the printer, hard wiring the printer to the WinXP computer through a USB cable, re-installing the printer’s wireless settings from HP’s installation disk, and repeating all of the networking and sharing setups on all three computers. This is a lot of work that is not worth repeating, because the successful results have not been permanent.

To: Neonskeleton,
Thanks for your response -- especially because you are an HP employee!
My Win2k machine does not use HP software, nor communicate to the HP printer. (HP did not write a Win2k driver for the P1102w -- and evidently no one else has done this, either.) My WinXP and Win7 machines use their HP drivers to send print jobs to the P1102w wirelessly, and both machines have the P1102w set up as a shared printer. Then, when I connect to those machines as a "guest" and submit a print job to those machines, those machines receive the print job and then communicate with the printer using the proper installed printer drivers.
Everything worked great with this configuration, until suddenly the printer was no longer responsive to ANY jobs coming from the WinXP machine, even though there was a "printer ready" indication on the WinXP machine, and even though the printer responded perfectly to print jobs coming from the Win7 machine.
When I tried to "fix" the WinXP setup by running HP's setup program on CD, nothing changed. Then, when I tried to reinstall the WinXP setup for wireless printing, the program insisted that I reset THE PRINTER'S factory defaults and proceed using a USB cable -- even though I wanted to simply ADD the computer for wireless communication to an existing networked printer! I would conclude that something screwed up the printer's inner settings (maybe an unsolicited and invisible HP update sent to my printer from the Internet?).
As I mentioned in my original post, I went through this process once before, reinstalled everything on all machines, and all was well. Until THE SAME non-recognition problem surfaced again!
I do not want to spend any more time on this. I went to Staples and bought a second P1102w printer (it is a nice little machine that uses a xerographic cartridge, rather than costly inkjet cartridges that frequently plug up). I'll use a USB cable for the connection, rather than the installed wireless feature, and set up the P1102w as a shared printer. I expect that all of my other computers will be able to link as a "guest" through the wireless hub and be able to print.
Thanks again.
PS. I am a retired computer-systems manager from Northrop Grumman.

How do I set up my HP psc2175xi all in one printer for wireless printing or network printing?

How do I set up my HP psc2175xi all in one printer for wireless printing or network printing?
I am changing the set up of my home computer to add another computer.
I would like to go wireless from my computers to the hub and wired from the hub to my
printer. I do not think this printer can do that since it does not have the ports to connect to a router hub, I think.
I am rather new to this way of setting up, so any help would be nice.

You could get a wireless router that supports USB printers, but these only support printing, not scanning. You could just go buy a new wireless printer since your printer is pretty old, anyway.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

What is the best printer for wireless printing with the iPhone?

What is the best printer for wireless printing witth the iPhone?

Roaminggnome has the list......pick on of those TERRIBLE printers and go for it....
I hope Apple see fit to broaden this list, because, having thrown away several of those brands in my life, I now have a network compatble BROTHER printer that's awesome,
"There's an app for that," ie the BROTHER, but you can only print pictures and soforth.
Apple, step up, open up the list of printers we can use!

Can't install canon pixma mp 980 for wireless printing

Similar Messages

Maybe you are looking for