Can't install Control and Simulation Module in LABVIEW2009

HI all,
I m using LABVIEW2009 x64 and wanted to update control module in it.
when ever I try to install the Control DEsign and Simulation module, the setup won't proceed.
IT shows the following error message : 
NI LabVIEW 2009 Control Design and Simulation Module
The Control Design and Simulation Module requires LabVIEW 2009 Full or Professional Development System to be installed.
however, I have already installed and reinstalled once as well. Please help me.

Hi Rishabh,
Unfortunately, we do not have a version of Control Design and Simulation for x64. You can try to install the 32-bit version of LabVIEW instead on a 64-bit OS. This should allow you to install CD&SIM.
Please let me know if can help any further.
Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

Similar Messages

  • Fpga, Control and Simulation Module

    Hello,
    I am trying to implement control by Control and Simulation Module through NI CRIO 9024. The error message pops up when trying the run the RT vi. 
    Other vis which are not coded by the Control and Simulation Module can work properly. However, when it comes to the Control and Simulation Module, the error message pops up. Is there anything wrong with the installation of the Control and Simulation Module? Please let me know if you have an idea about that. I appreciate your help.

    Hi Richard629,
    As seen in this Knowledgebase article, you most likely do not have the Control Design and Simulation module installed on the controller. You can use NI Measurement & Automation Explorer to install the Control Design and Simulation module on your controller.
    Regards,
    Allison M.
    Applications Engineer
    National Instruments
    ni.com/support

  • Control design and simulation module

    Hi,
    I am new to Labview and i am trying to work on Control System design. I have downloaded and installed the Evaluation Module of Control Design and Simulation Module. The problem I am facing witht this is its not showing any control fuctions in functions Palette. While installing it said its installing only control design and simulation assistant. Please, can anyone help with this.
    I am actually looking at this module to implement Sliding mode control for non linear systems. I would like to know if there are any examples to implement this??
    Thank You.

    Hello
    The problem is the following. The version of LabVIEW that you are using does not match the version of the evaluation version of LabVIEW Control Design and Simulation Module (CD&SIM). If that happens, the installer will not select the support files for your LabVIEW. If you download LabVIEW 2011, then you must install CD&SIM 2011.
    Now, the module in the current version does not have an example with sliding mode control. But using this module, you can easily implement the algorithms and simulation its result using the Control and Simulation Loop.
    Hope this helps.
    Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

  • Where can I find more information on Control and Simulation Software?

    Where can I find out more information on Control and Simulation Software for G (GSIM)?
    I am currently programming a PID controller using a Siemens PLC. I have installed LabVIEW DataLogging and Supervisory Control Module which allows LabVIEW to interface with my PLC.
    Would appreciate if you could offer me some advice on whether it would be possible for the PLC PID controller to control a first order process model created using GSIM? Please email me at [email protected] if you could offer me any advice or assistance.
    Merry Christmas and a Happy New Year.
    Best regards
    Donald

    I see that you posted to the DSC forum, but you did not get GSIM information. Below is the link for the user manual for the Control and Simulation Toolkit. It is the single best source for info on the toolkit.
    http://digital.ni.com/manuals.nsf/webAdvsearch/63E23F9BA1494FE98625665E00635898?OpenDocument

  • LabVIEW Control Design and Simulation Module version 2013

    I have had Labview downloaded for quite some time now. Downloaded control design and simulation module. Installed it. When i go to use it in the
    functions menu, only the window appears. Opening it shows an empty window. I have attached a screenshot of the issue. Could someone please explain to me what the problem is and how I can go about fixing it?
    Attachments:
    Labview screenshot.docx ‏998 KB

    As Altenback said, It is very possible it expired or it needs activation. To see for sure, go to your "NI License Manager" and expand the Modules. you should see:
    If not green then you have to fix the license.
    Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

  • Design control and simulation palette

    After hitting Next bottoms and succesfully installation for Design control and simulation toolkit , when I launchำก Labview programme  there is nothing in this function and the palette is blank. Anyone knows what happen.  I use Labview 2013 student edition 64 bit(free 6 months version). Thanks in advance+++
    Solved!
    Go to Solution.

    Do you truely have the 64bit version of LabVIEw installed?
    If you do, then you will not be able to use this module.
    It is only valid for 32bit LabVIEW.
    You can see the system requirements here:
    http://www.ni.com/labview/requirements/#cds
    You can try to install 32bit version of LabVIEW and then install the module.

  • How to use Fuzzy Logic Controller for transfer function in labview control and simulation loop?

    I am facing problem with fuzzy PD logic controller for transfer function in control and simulation loop.
    Plz Help me in this regard...................
    i have attache snapshot of my program
    Attachments:
    fuzzy in simulation loop.JPG ‏52 KB

    Hi Sankhadip,
    Sorry for the late response. I was looking at your code and
    I noticed that the graph scale does not start from zero. That might be the
    reason why you don't see the transient in the simulation. To change the scales
    simply double click on the lower limit and set it to zero. If this is not the
    expected results, can you please post the expected results, so we can see what are the
    differences between the results . Also, you might be using different
    solvers, and that gives different results as well.    
    Thanks and have a great day.
    Esmail Hamdan | Applications Engineering | National
    Instruments

  • Control and simulation

    For someone who is skilled in labview and spare some time ,I am new to labview and found an intersting labview application which it can be used as a start for control and simulation. I would like a help to run this vi and see what could be added to it to make it more usefull.
    Attachments:
    RS.vi ‏84 KB

    Bin,
    You should post this question to the page where you found the VI, and ask ADEEB or Al S what they used the VI for.
    Zvezdana S.

  • Synchronize Control and Simulation loops

    When simulating control systems with LV Control and Simulation loops, I often have multiple loops running at different rates. For example, I have a PWM loop running at 20 kHz, a data acquisition loop running at 100 kHz, and a control loop running at 10 kHz. How can I synchronize all of these loops so that they stay on the same time base? Obviously the master time base will need to be at least as fast as the fastest simulation loop.
    I've tried synchronizing all loops to the 1 kHz clock (I'm running on Windows), but each loop runs one period per clock tick (e.g. my 20 kHz loop counts up 50us per clock tick, my 100 kHz loop counts up 10us per clock tick, etc). I need all of the loops to be synchronized to one master time base so the simulation time is identical in each loop, but each loop will be executed at a different rate.
    Any thoughts?
    Solved!
    Go to Solution.

    Hello,
    A quick suggestion - why can't you run all three systems in a single simulation loop, but have different sample rates for the blocks for each system ?
    Is your system entirely digital, or a mixture of continuous and digital - it may simplify things if you can convert everything to discrete time.
    Hope this helps,
    Andy Clegg
    Consultant Control Engineer
    www-isc-ltd.com

  • Resetting Integrator in Control and Simulation Loop

    Hello,
    I am trying to run a real-time simulation in Labview 14. I have prepared front panel controls and data flow such that I can reset the simulation to some preset initialization values upon clicking a button. However, I am not able to figure out how to reset the integrator in the control and simulation loop. Even after reinitialization of all the values, the integrators will overwrite the initialization values with whatever they were holding. Please help me find a way out.
    Thanks

    Please share what code you have so that we can see what you've tried and understand exactly what you're trying to do.

  • How many times can I install Photoshop and Premiere Elements 13?

    How many times can I install Photoshop and Premiere Elements 13?

    mbuenger
    Are you referring to how many times can I install, uninstall, reinstall Photoshop Elements 13 or Premiere Elements 13 on the same computer?
    Or, how many of your computers can have a same purchased activated serial number at the same time for either of these products?
    If the former, I know of no limit.
    If the latter, the answer would be as John as mentioned.
    ATR

  • Installed CS6 all but Illustrator installed correctly, I received error DF024, DW063, and DW050, how can I install Illustrator and fix these errors?

    installed CS6 all but Illustrator installed correctly, I received error DF024, DW063, and DW050, how can I install Illustrator and fix these errors?
    this is the log error file I get:
    Exit Code: 6
    Please see specific errors and warnings below for troubleshooting. For example, ERROR: DF024, DW063 ...
    -------------------------------------- Summary --------------------------------------
    - 0 fatal error(s), 4 error(s), 0 warning(s)
    ----------- Payload: {AAF0D225-F129-40F2-916E-12E28DBD19ED} Adobe Illustrator CS6 Core 16.0.0.0 -----------
    ERROR: DF024: Unable to preserve original file at "/Applications/Adobe Illustrator CS6/Adobe Illustrator.app/Contents/Frameworks/AdobeCrashReporter.framework/AdobeCrashReporter" (Seq 1649)
    ERROR: DW063: Command ARKDeleteFileCommand failed.(Seq 1649)
    ERROR: DW050: The following payload errors were found during install:
    ERROR: DW050: - Adobe Illustrator CS6 Core_AdobeIllustrator16en_USLanguagePack: Install failed
    ERROR: DW050: - Adobe Illustrator CS6 Core: Failed due to Language Pack installation failure

    hold down shift-cmd-alt while starting ai.  if done correctly, you'll see a preferences reset prompt.
    if that fails, uninstall, clean and reinstall per Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6

  • Can I install Lightroom and/or Photoshop CC on my Android tablet?

    Can I install Lightroom and/or Photoshop CC on my Android tablet?

    Not the regaular versions, however we have Photoshop Touch CC which you can install and use on Android.

  • I can not install Waik and mdt on server 2012 so that i can deploy windows 7 please may you help me?

    i can not install  Waik  and mdt on server 2012 so that i can deploy windows 7 on target machine, i have downloaded mdt  Waik i got error saying you must install frame 2.0  which needs also adk windows 8. i am using hyper  machine.
    thank you

    Hi Warsame12,
    It is worth mentioning that don’t use IPV6 PXE, Windows 7 doesn’t support WDS 2012 deployment over IPv6 PXE. If IPv6 PXE boot is enabled and a 
    Windows 7 installation is selected, a blank screen will appear and Setup will not run.
    The related KB:
    Windows 7 client deployment over IPv6 PXE network boot does not work.
    http://support.microsoft.com/kb/2803741
    I’m glad to be of help to you!
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Can I install 8.5.1 modules on a LABVIEW 8.5 system

    Can I install 8.5.1 modules especially ARM module on a LABVIEW 8.5 system ...
    Since 8.5.1 is just a minor upgrade to 8.5 I guess it should do ..
    But does it work effectively while importing code to  ARM processor

    Hi Bharath,
    No, it's not a good ideal to install an 8.5.1 module on LabVIEW 8.5.  It may function, but chances are that it won't.  The versions should match exactly.
    You will want to upgrade your LabVIEW to 8.5.1 before installed the LabVIEW Embedded Module for ARM Microcontrollers.  (Of course, you are welcome to try, but I suspect that you will get an installation error.)
    Kevin S.
    Applications Engineer
    National Instruments

Maybe you are looking for